Hello, excuse my bad english I'm using google translate.
The problem I have is that my xperia xa is dead.
the reason of it, was that I wanted to flash the rom of my cell to remove the applications that come with the mobile company.
when I realized my error, was that I did the following, in the flash tool, in the rom selection, I made the error, not selecting the following settings:
-APPS_LOG
-DIAG
-QNOVO
-USERDATA
-CUST-RESET
as shown in the following image:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
when the flash operation ended, the cell phone did not want to turn it on, the only function it had and has so far, is that it does not vibrate, it does not turn on, it does not go into flash or fastboot mode, it's dead, it just turns on the red led.
when I try to perform the flash operation again, I simply get the following message when I connect the device.
in the windows device manager, recognizes the phone as "usb serial device (com)".
I searched the net, and I did not find the solution to this problem, I appreciate your attention, and I expect some help.
PD: I already tried the connection with pc companion, and even the function from system symbol of windows with the tool fastboot to flash the boot, with the img.
the problem is that the device does not go into any mode
1990macsfull said:
Hello, excuse my bad english I'm using google translate.
The problem I have is that my xperia xa is dead.
the reason of it, was that I wanted to flash the rom of my cell to remove the applications that come with the mobile company.
when I realized my error, was that I did the following, in the flash tool, in the rom selection, I made the error, not selecting the following settings:
-APPS_LOG
-DIAG
-QNOVO
-USERDATA
-CUST-RESET
as shown in the following image:
when the flash operation ended, the cell phone did not want to turn it on, the only function it had and has so far, is that it does not vibrate, it does not turn on, it does not go into flash or fastboot mode, it's dead, it just turns on the red led.
when I try to perform the flash operation again, I simply get the following message when I connect the device.
in the windows device manager, recognizes the phone as "usb serial device (com)".
I searched the net, and I did not find the solution to this problem, I appreciate your attention, and I expect some help.
PD: I already tried the connection with pc companion, and even the function from system symbol of windows with the tool fastboot to flash the boot, with the img.
the problem is that the device does not go into any mode
Click to expand...
Click to collapse
2 times so far, my XA died the same way after trying to flash a mod. Both times I was eventually able to resurrect it by holding down various combinations of buttons while plugging and unplugging, trying different cables, etc. The second time, it wouldn't do anything until the next day, and then it suddenly came to life when using a different cable and plugging into the wall while holding power and volume down. I would try it. I'm not too familiar with flashtool on XA. I have used it for 3 years with my Z1c and never hard bricked a phone with it. Seems like X series have a little bit different rules, but I don't see why your phone would hard-brick just because you didn't wipe a few partitions... Also good idea to check in with FT thread.
If the computer does recognize it, maybe you need to reinstall your usb drivers. If its not, then u have a big problem with it, before making anything you need to see if there is a way to connect it by Fastboot, and install his custom TWRP. if u are able to do that, there is a sollution for you.
Remember always to install your usb flash drivers, and the fastboot drivers too.
Same problem my XA F3113 is dead. The LOG says everything was ok but after disconnect it from PC the phone dies.
Look like exist a way to get it back to life but we need the SCATTERED FILE.
Can somebody share us the SCATTERED FILE of this Model?
Really appreciate this guy....
Awesome person. He had recover my dead XA ultra through online. Just with 500 INR.
wrundawan said:
Whats app me +918147499618 I can help you to fix your dead phone.
Click to expand...
Click to collapse
i have a same problem
please help. my phone f3113 is dead after downgrade
wrundawan said:
Whats app me +918147499618 I can help you to fix your dead phone.
Click to expand...
Click to collapse
Be careful this guy is a cheater he cheated $30 from me
Who the hell has cheated you?
Check your paypal with your open eyes since you had raised claim on your money inside paypal your money was refunded by them. And I am helpless as I didn't got your money.
mballe francois said:
Be careful this guy is a cheater he cheated $30 from me
Click to expand...
Click to collapse
mtk scatter
Related
Hello guys. I've ran into a trouble from nowhere with my phone. I've installed Link2SD to copy unmoveable apps to sd card, edited some things to GravityBox, pressed reboot button, and phone has had never turned on. It's not responding on fastboot nor flashmode. Battery was about 40% and phone was charging. I can't do anything to put the phone back on. It doesn't vibrate when pressing power key, it't just behaving like it has no battery inserted. Battery is good, phone is 4 months old, unlocked bloader, rooted, 1.12 stock, thunderzap 4.1-r2. If you want more info, just ask, I will provide as much as I can. Please help me
If it doesnt respond to fastboot/fastmode it might be better to take it to a service center
Tapatalked that sh*t
Joery360 said:
If it doesnt respond to fastboot/fastmode it might be better to take it to a service center
Tapatalked that sh*t
Click to expand...
Click to collapse
What do You think could go wrong? It just happened, but why?
aerzjee said:
What do You think could go wrong? It just happened, but why?
Click to expand...
Click to collapse
Buy another battery before you take it to a service center just in case but you will need to relock the bootloader and restore ta partition or they won't touch it. sounds like a hard brick corrupted boot partition
gavster26 said:
Buy another battery before you take it to a service center just in case but you will need to relock the bootloader and restore ta partition or they won't touch it. sounds like a hard brick corrupted boot partition
Click to expand...
Click to collapse
But the problem is, that I can't relock bootloader, because the device isn't responding to anything. I can't boot in flashmode, fastboot or normally. It is just dead. The PC sees the phone as USB Input Device, or as unknown device.
I've tried different systems, different computers, nothing has helped.
Try following the instructions given here
S1N1S73R said:
Try following the instructions given here
Click to expand...
Click to collapse
But the phone is seen as Unknown Device, doesn't matter how I would plug it. If I connect my phone to charger, nothing happens. It's just behaving, like I would plug phone to charger, but not to socket in wall.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
aerzjee said:
But the problem is, that I can't relock bootloader, because the device isn't responding to anything. I can't boot in flashmode, fastboot or normally. It is just dead. The PC sees the phone as USB Input Device, or as unknown device.
I've tried different systems, different computers, nothing has helped.
Click to expand...
Click to collapse
Did you partition your internal sd for link2sd
gavster26 said:
Did you partition your internal sd for link2sd
Click to expand...
Click to collapse
Nope, only moved few apps like I normally would by using settings > apps. I did it by link2sd because it was faster for me.
aerzjee said:
Nope, only moved few apps like I normally would by using settings > apps. I did it by link2sd because it was faster for me.
Click to expand...
Click to collapse
Ok what exactly did you do in gravertybox
Try with other usb cable
Sent from my C2105 using xda premium
aerzjee said:
But the phone is seen as Unknown Device, doesn't matter how I would plug it. If I connect my phone to charger, nothing happens. It's just behaving, like I would plug phone to charger, but not to socket in wall.
Click to expand...
Click to collapse
Had the exact same problem with my Xperia L.
It somehow entered the firmware downloader mode for the qualcomm cpu after rebooting, but could not fix it and had to send it back.
The unknown device is QHSUSB_DLOAD, drivers from here work fine
http://forum.xda-developers.com/showpost.php?p=14909282&postcount=19
after repair, service said they needed to replace the main board in the phone.
gavster26 said:
Ok what exactly did you do in gravertybox
Click to expand...
Click to collapse
I've unlinked ringtone volume from notification volume. I've just laughed at my phone when I saw it hard-bricked :laugh:
virald said:
Had the exact same problem with my Xperia L.
It somehow entered the firmware downloader mode for the qualcomm cpu after rebooting, but could not fix it and had to send it back.
The unknown device is QHSUSB_DLOAD, drivers from here work fine
http://forum.xda-developers.com/showpost.php?p=14909282&postcount=19
after repair, service said they needed to replace the main board in the phone.
Click to expand...
Click to collapse
Is there any thing I can do in that firmware download mode? Forcing it to boot an image it already has? Is it similar to U-Boot from other SoC's (like in routers)? If yes, I think I could get it working.
virald said:
Had the exact same problem with my Xperia L.
It somehow entered the firmware downloader mode for the qualcomm cpu after rebooting, but could not fix it and had to send it back.
The unknown device is QHSUSB_DLOAD, drivers from here work fine
http://forum.xda-developers.com/showpost.php?p=14909282&postcount=19
after repair, service said they needed to replace the main board in the phone.
Click to expand...
Click to collapse
It seems that my issue is different, or I'm installing that driver in wrong way.
EDIT: If it could help You in anything, device identificator is: USB\VID_0FCE&PID_D18E&REV_0000
Hello,
so today I wanted to root my LG g4 Stylo (H635) with kingoroot (downloaded latest version from XDA with a APK file to install it on my mobile phone). So after restarting the phone I got this error:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
This keeps repeating, I mean it restarts and gives the same result. Hard reset does not work cuz it goes also in the same direction. Is this phone completely bricked or can I do something in home to unbrick it? Or am I convicted to give it to the warranty and pray for my innocent?
spaykerek said:
Hello,
so today I wanted to root my LG g4 Stylo (H635) with kingoroot (downloaded latest version from XDA with a APK file to install it on my mobile phone). So after restarting the phone I got this error:
This keeps repeating, I mean it restarts and gives the same result. Hard reset does not work cuz it goes also in the same direction. Is this phone completely bricked or can I do something in home to unbrick it? Or am I convicted to give it to the warranty and pray for my innocent?
Click to expand...
Click to collapse
It not hard to fix.
try this http://guidebelajar.blogspot.com/2015/11/guide-to-flash-bricked-bootloop-lg-g4-stylus.html
hopefully your version is on download page if not google h635 kdz and you'll find it.
Complete instructions and download links are at the above address
Turns out you're right, you need to enable oem unlock and keep it active. otherwise the root fails every time.
Hello,
thank you for your help guys. @Thediesel1972, the problem was that I couldn't even boot my phone and my pc didnt' even detect my phone at all. What I did was a Download mode which saved me, but I appreciate your input and thank you for your link, gonna be for later if I fail with something. @TheDerekHarper, I had that option turned ON and when Kingroot tried to root my mobile phone it restarted and the error occured like it's on the screen. I couldn't even make it with hard reset cuz the mobile phone restarted and it was a loop which never ended.
@topic
to fix it, you need to press volume UP and press the USB cable to your pc and check if the mobile phone turns out to the Download mode.
Thank you and greetings once again.
Hi, i have the same problem but it's very easy to solve. Download the software LG Bridge and go to Software Update connect the device in download mode (vol up and insert usb cable) and click on software error recovery and the program start the process
My device Metro Stylo i actually used Lg Bridge also to Recover my phone even though i had the Tmob 6.0 Update flashed to my phone which is the H631 LG Bridge recognized my phone as the Metro Stylo MS631
I installed LG bridge from their site but it was all in Korean. After figuring out how the change it to English I tried connecting in download mode, but LG bridge just says can't connect, please disconnect your USB cable from the computer and try again.... Does not seem to see the phone at all.
LG bridge method didn't work for me
The LG Bridge method was a no go for me. I did find this to work, http://forum.xda-developers.com/lg-...o-t-mobile-h631-unbrick-t3339329#post66240431.
Unfortunately it wipes the device and returns it back to out of box state. That's better than what i did have though.
Just another suggestion
Hey guys, did anyone find a mirror for the h635 stock firmware? It dissappeared from the official LG servers for some reason.
im having this exact problem. is there a fix or no... ive tried everything out there.
Same problem
I had exactly the same problem. Your phone isn't completely bricked, but I don't have the solution to repare it at home. I send it to repare company en I was lucky. I honestly told that I rooted my phone and that it went wrong. And they repaired it without loosing my warranty:laugh:
I got it back completely well functioning. And they even installed android 6.0 for me. But the same problem stays at hand. The internal storage is to small. That was the reason to root the phone. Sow if someone has the solution......maybe I dare to try it again. (fingers crossed) LG G4S H-635
Try the LG Bridge flashing software from the return to stock thread. The Korean one didn't seem to work for me as I remember.
I will be straightforward:
I bought an used OPO, I booted it up, configured the phone, took a photo and then decided to reboot it (turn off and then turn on), then my device simply hard bricked.
1. I already tried turning it on, the device does nothing (no vibration).
2. I already tried using Power + Vol Up and Power + Vol Down, nothing happens (no vibration).
3. Windows recognizes the device as "QHSUSB_BULK", I already tried installing the drivers and using ColorOS flashing tool from here http://forum.xda-developers.com/oneplus-one/general/guide-unbrick-oneplus-one-t3013732 , the device IS RECOGNIZED by the tool, but when I start flashing, it starts a loop when trying to flash the "8974_msimage.mbn" file (the progress bar goes until the end and then the process repeat in the same file).
Yes, the device has the bootloader unlocked, because the previous owner flashed a custom ROM, custom kernel and SuperSU.
No, the device isn't recognized by adb.
No, the device isn't recognized by fastboot.
I already tried searching on Google for this issue, everyone who had this issue never replied saying that they fixed the issue...
I never had any kind of soft/hard brick on my Moto G 2014 (and I flashed custom ROMs constantly on it)... so... can someone help me? Thanks!
I'm also willing to give 5$ on PayPal to someone who can fix this issue.
Also, if I try to use the ColorOS flashing tool, the device disconnects in the middle of the process, causing the infinite flash loop.
First, if you have a computer which installed Windows XP, just flash the ROM with COLOROS tool.
Second,if you a using Windows7 or later,,give me a photo of what the COLOROS tool showed.
Thanks for forgiving my poor English
sino1641 said:
First, if you have a computer which installed Windows XP, just flash the ROM with COLOROS tool.
Second,if you a using Windows7 or later,,give me a photo of what the COLOROS tool showed.
Thanks for forgiving my poor English
Click to expand...
Click to collapse
Nah, your english is fine, I could understand what you are saying.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After I clicked "Start"
Then the "device plugged in" sound plays and the process repeats...
It keeps doing this:
(If you can't view the images, click here:
http://lori.mrpowergamerbr.com/sharex/Msm8974DownloadTool_2016-07-22_10-39-42.png
http://lori.mrpowergamerbr.com/sharex/Msm8974DownloadTool_2016-07-22_10-40-18.png
http://lori.mrpowergamerbr.com/sharex/2016-07-22_10-41-05.gif
)
Morning,my friend.
I tried to brick my OPO for testing.
Here's the solution.
First,open Device Manager and checked this(dont know how to speak in English):
Second, open COLOROS tool,click start and it will show the situation like what happened to you.
NOW,check Device Manager again.
Has three ways.
1.shows 9006 and MMC storage.COLOROS tool wil continue later.
2.shows QHSUSB_BULK with a yellow ! before,means no driver.
3.shows unknown device,means not enough elec.
You should be the second way.
Third,Disable Signed Driver Enforcement in Windows 7 or later.
My laptop company's suggestion:
http://acer.custhelp.com/app/answer...windows-10:-disable-signed-driver-enforcement
After that, reinstall the bricked driver and everything will be in way 1.
At last,wait for the imgs downloading,unplug microUSB,press power and reboot twice,then you can unlock bootloader and do what you want.
sino1641 said:
Morning,my friend.
I tried to brick my OPO for testing.
Here's the solution.
First,open Device Manager and checked this(dont know how to speak in English):
Second, open COLOROS tool,click start and it will show the situation like what happened to you.
NOW,check Device Manager again.
Has three ways.
1.shows 9006 and MMC storage.COLOROS tool wil continue later.
2.shows QHSUSB_BULK with a yellow ! before,means no driver.
3.shows unknown device,means not enough elec.
You should be the second way.
Third,Disable Signed Driver Enforcement in Windows 7 or later.
My laptop company's suggestion:
http://acer.custhelp.com/app/answer...windows-10:-disable-signed-driver-enforcement
After that, reinstall the bricked driver and everything will be in way 1.
At last,wait for the imgs downloading,unplug microUSB,press power and reboot twice,then you can unlock bootloader and do what you want.
Click to expand...
Click to collapse
Thanks for replying!
Sadly, your suggestion didn't work, I plugged in the OPO, opened Msm8974DownloadTool.exe and clicked "Start", closed drivers manager and reopened it and nothing changed (It was like your first screenshot)
EDIT: And yes, I'm on Test Mode + Allow Unsigned Drivers
MrPowerGamerBR said:
Thanks for replying!
Sadly, your suggestion didn't work, I plugged in the OPO, opened Msm8974DownloadTool.exe and clicked "Start", closed drivers manager and reopened it and nothing changed (It was like your first screenshot)
EDIT: And yes, I'm on Test Mode + Allow Unsigned Drivers
Click to expand...
Click to collapse
Open Device Manager.
Press Power &Vol Up for about 10 seconds.
See if it will change between 9008 and 9006.
I have same thing did it work
I am just wondering if u managed to fix it.
I had the exact same issue. To stop the device from disconnecting, I needed to remove all existing drivers, let the phone charge, plug it into the PC. Hold volume up + power until the PC recognises it. Then I used the color OS flashing tool.
I had to run it as administrator, and it worked fine on Windows 10, without anything extra. However remember you'll lose all your stuff. Lucky for me I had a backup of my entire phone on my PC when I switched file system to F2FS.
This issue in itself has really baffled me. It happened to me when flashing sultans rom, and the phone completely bricked. However I'm using the rom now after fully recovering the device... I guess it's just down to bad luck?
mark1320 said:
I am just wondering if u managed to fix it.
Click to expand...
Click to collapse
Nope, never fixed it, I don't even have the device anymore (now rocking a Moto G Turbo)
mark1320 said:
I am just wondering if u managed to fix it.
Click to expand...
Click to collapse
Don't use "msm8974-download-manager" use qfil to recover the phone. Worked for me.
http://www.androidbrick.com/ultimate-qualcomm-snapdragon-unbrick-guide-snapdragons-are-unbrickable-qhsusb_dload_qpst_qfil/
Download 2012 qhs diagnostic driver and use xp machine.It will work just fine.
install a fresh windows either x32/x64 winxp/win 7 extract color OS and install the correct drivers
Well I have tried every way to get my LG D686 up and running again before that let me revise how I got here
1 - i rooted the LG D686 in 2016, it worked well for a year until one day I had got a certification boot error msg on start up and had no access to bypassing that except the download mode
2 i downloaded a firmware for D685 instead and flashed it with LG FLASHTOOL. It got hard bricked. When ever I would connect it to the pc it would just connect and disconnect repeatedly. it would not turn on or go in recovery or download mode nothing
3- then i tried to use this method here https://forum.xda-developers.com/optimus-g-pro/help/exclusive-solution-lg-d686-dead-flash-t3330691 . I opened the phone managed to short the resistor to ground and got the PC to recognize the phone in mtk mode. Used SP flash tool flashed it successfully but the phone still wont turn on and even tried a hard reset.
4 - I only want to know if its bricked for good or is there still a chance. The mobile repair shop says hardware and software is gone for a toss , will cost allot to fix, however that was before i tried the testpoint method here https://forum.xda-developers.com/optimus-g-pro/help/exclusive-solution-lg-d686-dead-flash-t3330691. Since I was able to short the resistor on the mother board now the pc detects my phone and never disconnects (in MTK mode) which is a good thing ( i have closed the phone so for now its assembled, i have been able to do a format/downlad 100% successfully with the phone assembled
Do I have a bricked phone for good ? or is there any chance?
I have also attached photos of my progress but my phone will never turn on be it fastboot mode , recovery mode, hard reset, no vibration too. Once I even kept the phone charged for a whole night and checked the battery voltage with a multimeter and it says about 90% charge again that was before i tried this test point method, now if i keep it charged on the charger adaptot the back of the phone right near the sim card slot is never warm as before. its cool which i feel its not being charged now. but if its connected to the PC yes , the area near the simcard slots is warmer, so i guess its getting charged.
I have d686 scatter firmware files from A_1st™ Support Team
I have SP flash tool (tried latest one as well however this version works well for scanning emmc.txt)
drivers are detected properly on PC . i have attached an image for that as well
I apologize if creating this thread is breaking any rule violations but there was no reply on the page/ thread i was seeking help for hence I thought I will start a new thread
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Any one have any idea the hardware needs replacement ???
Is this phone to old for an answer ? Just a simple yes or no . Is it bricked for good that the mother board needs to be replaced ? Or is there a chance I can recover it ?
after i got into Fastboot Mode for a Longtime about 30mins.. my Phone got blackscreen and no sign of Light even in Notification Light. i tried to turn it on holding the Power Button for about 30sec or more it doesnt do anything.. soo i go to Device Manager and i see in ports that the Phone is detected with labaled name "Qualcom SDH 9008" and installed MiFlash Tool, and i was trying to Flash it when i press Refresh it detects as "COM3" after searching on YouTube for lot of many ways i didnt find any solution like FireHose File to bypass MiFlash Auth. but i didnt see anything for Poco x3 Pro. no luck!
i already TestPoint the back of the Phone but the only Prob is the Auth thing in account to Proceed to Update firmare file .tgz
can someome help me pleaseee its been Day 4 of searching and still no luck! my Phone is sleeping for 4days now. and i dont have any Phone. im from Philippines by the way.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
PHnambawan said:
after i got into Fastboot Mode for a Longtime about 30mins.. my Phone got blackscreen and no sign of Light even in Notification Light. i tried to turn it on holding the Power Button for about 30sec or more it doesnt do anything.. soo i go to Device Manager and i see in ports that the Phone is detected with labaled name "Qualcom SDH 9008" and installed MiFlash Tool, and i was trying to Flash it when i press Refresh it detects as "COM3" after searching on YouTube for lot of many ways i didnt find any solution like FireHose File to bypass MiFlash Auth. but i didnt see anything for Poco x3 Pro. no luck!
i already TestPoint the back of the Phone but the only Prob is the Auth thing in account to Proceed to Update firmare file .tgz
can someome help me pleaseee its been Day 4 of searching and still no luck! my Phone is sleeping for 4days now. and i dont have any Phone. im from Philippines by the way.
View attachment 5333005
Click to expand...
Click to collapse
Listen to me carefully extract the .tgz file in a folder and download platform tools from the web and also extract platform tools files also in the same folder where you extracted the .tgz files after keeping both file extraction in a folder then turn your phone in. Fastboot mode and plug in and run the flash all .bat file it gonna take around 10-15 minutes and your device will recover
Did it solve your problem??
You are most likely in EDL mode. In order to get out of it, you need to snap off the battery and connect it back. Perhaps no flashing is needed
You can try to find authorized user patch for miflash somewhere on net but don't get your hope up as poco is relatively new
oleg.ignatov2011 said:
You are most likely in EDL mode. In order to get out of it, you need to snap off the battery and connect it back. Perhaps no flashing is needed
Click to expand...
Click to collapse
Does this method really work? im on Redmi Note 9 Pro, Hardbricked as well, and also stuck at edl authentication ehrn attempting to flash fastboot rom
oleg.ignatov2011 said:
You are most likely in EDL mode. In order to get out of it, you need to snap off the battery and connect it back. Perhaps no flashing is needed
Click to expand...
Click to collapse
Does This Method Work? Im on Redmi Note 9 pro hardbricked as well, I Also cant get past to Edl Authentication
Did you resolve the issues. and method used. I am also stucked in the same.
kiyookusanagi said:
Does This Method Work? Im on Redmi Note 9 pro hardbricked as well, I Also cant get past to Edl Authenticatio
Click to expand...
Click to collapse
If your computer is detected as QH 9008 or similar, it seems to be more of a hardware fault than a software one, since it indicates that the CPU is not having good communication with the UFS memory.
PHnambawan said:
i already TestPoint the back of the Phone but the only Prob is the Auth thing in account to Proceed to Update firmare file .tgz
Click to expand...
Click to collapse
How did you do this?
Can you explain the process step by step, pls.
I've tried with several different ways but no one works. Phone isn't getting in EDL.