Hi,
Hope this it the correct place to ask this question, if not i can someone please give me a hint where to post.
Have an issue with my Xperia V / lt25i after installing a boot animation with ROM Toolbax Pro, think it was the Xperia Play animation, or one with an animation in the start and ends with a Sony Ericson logo.
When i turn on the phone, the animation runs for a few seconds, then the geen/white Sony E logo appears, and after some seconds the screen dims the light and then it goes black, like when the screen turns of before the phone locks normaly.
Pressing the on/off / lock button turns the screen back on again, and the logo is shown, and after some seconds it goes black again.
Flashed the LT25i_9.1.A.1.140_1268-6904.ftf file downloaded from another thread on this site.
The phone is flashed with Flashtool (v 0.9.10.1 for Windows) and then rooted with Bin4ry (v 26) and worked fine before installing the boot animation.
Have disabled USB Debugging after i rooted the phone, so no luck getting access to it so far.
Is there a way to bypass the boot animation?
Or a way to reset the phone, so the original boot animation will be re-installed and getting access to the phone?
Did try the guide on this site phonetipsandtricks.com to perform factory reset and hard reset, but no luck, the phone just starts up with the same animation and ends with the logo, and then the screen goes black.
Any suggestions ?
Kind regards,
Alex
Maybe there is a way to re-flash ...
Hi ...
Started pressing the screen to see weather or not the boot animation actually just stopped, or it maybe just blocked the screen from the actual startupscreen with the pattern to unlock.
Managed to unlock the phone, still with the SonyE logo on the screen and otherwise a black screen, and pressed the voloume up/down and heard the beep when pressing, getting louder or weaker, so managed to get into the phone in "the blind" sort of say.
Will try to get into the USB Debugging setting from what i remember of the structure of the menu, if i can just get that one enabled, then maybe it will be possible to use Flashtool and re-flash.
Time for a little experiment with fingers on the display.
Kind regards,
Alex
Phone re-flashed and rooted again.
Hi.
Just an update ...
Managed to find the USB Debugging setting and activate it on the black screen and have now re-flashed and rooted the phone and looks like it's working just fine now.
Alex
hello. from some time, after a while 'time of use of the nexus 5 the screen goes black. If i press rhe power botton, only thing I see on the screen is the option of switching off. This has happened to me with the 5.0.1 and 5.1.1. I have supersu 2.49. you think it is a hardware or
software problem? I flashed clean ROM with fastboot.
Thank
Hi everyone, please help me.
I am using a d6633 dual sim z3, using stock sony android 5.0 rom, Locked bootloader but I got root and already installed ZX dual recovery.
I use to see a green led light while restarting my phone, and when i press vol - it will boot into recovery mode.
but now I don't see any colour led light while restarting, which means it doesn't boot in recovery mode :crying:
My led light works fine when noification comes out.
Don't know what is going on, please help MEEEEEEEEEEEEEEEEE:crying::crying::crying:
Install zx dual recovery from your pc again, if not worked then try again & again, i hope your problem will b solve.
Hello everyone! This is my first post and I am not a noob nor an expert. So by the way I had a Sony xperia t2 ultra dual D5322 and I soft bricked it when I flashed twrp recovery and it didn't boot anywhere except recovery then I erased everything from my phone from recovery and reboot without an os installed and hard bricked . after a time I found Sony flash tool by androxyde (I guess that's his name) and flashed Sony t2 dual wrong model (D5303) but it did enable fast boot so from that I flashed D5322 4.3 firmware but the screen has gone black. When I hold power button it vidrates then I swipe up on screen then it gives the screen unlock sound and then I can toggle with the the volume buttons to see if it is working and its fine but the screen is black. And the firmware came with usb debugging off. Any help? I hope!
Hello,
I have flashed lineage os 14.1 on my Sony Xperia E3 and everything works fine except the issue, that when i press the power button to get it to sleep and after that I press the power button again the screen remains unresponsive. It's happening in recovery mode also.
what can I do? what is the root of the Problem?
Sorry for my bad english
Greetings