Samsung J5 2016(SM-J510FN) Brick - General Questions and Answers

Hi everyone , i have a Samsung J5 2016(SM-J510FN) , i have stock ROM + Root + TWRP on the phone, 2 days ago i try to make factory reset from android menu , after that my phone restarted but every time start only in TWRP recovery mode , i try it to make it a clean install with Odin but every time is stuck on <ID:0/004> aboot.mbn , or an older version of Odin give me fail , i try it to install a custom rom with twrp , install succesfuly but start again only in TWRP recovery mode , i try to use SmartSwitch from samsung , but say my S/N is not valid ( i think becouse is from Romania) , on Download mode i have this mesage if help
Product Name SM-J510FN
Curent Bynary: Custom
System Status: Custom
Fap Lock: OFF
Waranty void: 0x1 (2)
Qualcom Secureboot: Enable (CSB)
RP SWREV: S1 , T1, R1, A2, P1
Secure Download: Enable
i try to flash another TWRP to fix it problem , stuck on image.img , how can i unbrick this idiot phone?

your hard is dead ! u should to change the hard . or change your main board
You should not retset factory when your charging Below 70%

Related

Galaxy note 4 sm n910f stuck in odin mode

I need help recovering my galaxy note 4 model sm n910f.
I tried installing TWRP recovery using TWRP Manager from playstore the installation was unsuccessful now the phone wont boot and is stuck in odin mode.it displays the following
Could not do normal boot
ODIN MODE (HIGH SPEED)
PRODUCT NAME:SM N910F
CURRENT BINARY:Custom
SYSTEM STATUS :Custom
REACTIVATION LOCK(KK): ON
KNOX WARRANTY VOID :0×1
QUALCOMM SECUREBOOT : ENABLE (CSB)
AP SWAREV : S1, T1, A1, A1, P1
SECURE DOWNLOAD :ENABLE
UDC START
Phone is on stock rooted 4.4.4 kitkat
Solution greatly appreciated

Bricked Rooted Galaxy Core Prime

OP Junior Member2 posts Thanks: 0
Help me please I rooted my prime with kingroot that went great. I then downloaded and installed the twrp I flashed it using flashify it then re booted upon reboot it would not boot past the Samsung logo with this dialogue in the upper left hand corner
Odin mode
Product name : sm- g360t1
Current binary: Samsung official
System status : official
FAP lock: off
Qaulcomm secureboot: enable (csb)
Rp swrev: s1 t1 h1 r1 a1 p1
Secure download: enable
I can't get it to hard reset or into download mode it just turns off when I try
I do not have a pc and was wondering if there is any way to unbrick my phone without a pc or if I have to use a pc how to do it?

Please help s7 is bricked I can not boot the phone

I have Galaxy S7.
I try to root the phone and put superman rom on and now the phone won't boot. I mean it's not booting at all. I try to boot in recovery mode and it shows
Recovery booting .... in blue and it goes to blue screen and it says in red custom binary blocked by secure boot (boot img) and also "system software not authorized by att has been found on your phone etc.
And when I go downloading mode it shows
Odin mode high speed
Product name smg930a
Current binary custom
System status custom
Fap lock on
Warranty voided 0x0
Qualcomm secure boot enabled
Rp swrev: n4 (2,1,1,1 ) k1 s3
Secure download enable
You can't flash a stock ROM from download mode with ODIN?
Well you can try to flash back a stock rom or try to recover the firmware with samsung kies 3.

[Resolved] J510fn twrp

Hi everyone , i have a Samsung J5 2016(SM-J510FN) , i have stock ROM + Root + TWRP on the phone, 2 days ago i try to make factory reset from android menu , after that my phone restarted but every time start only in TWRP recovery mode , i try it to make it a clean install with Odin but every time is stuck on <ID:0/004> aboot.mbn , or an older version of Odin give me fail , i try it to install a custom rom with twrp , install succesfuly but start again only in TWRP recovery mode , i try to use SmartSwitch from samsung , but say my S/N is not valid ( i think becouse is from Romania) , on Download mode i have this mesage if help
Product Name SM-J510FN
Curent Bynary: Custom
System Status: Custom
Fap Lock: OFF
Waranty void: 0x1 (2)
Qualcom Secureboot: Enable (CSB)
RP SWREV: S1 , T1, R1, A2, P1
Secure Download: Enable
i try to flash another TWRP to fix it problem , stuck on image.img , how can i unbrick this idiot phone?

SM-J710FN with Binary 6 HELP

Hello, long story short.
I wanted to install TWRP on my J710FN and when I did so it wouldn't boot got stuck on the logo.
So, I tried to flash the stock firmware but the thing is my phone has a U6 binary.
I can't unbrick it using odin to flash the stock firmware because I cant find any U6 firmwares for my device.
I tried to flash these:
J701FXXU6BRH9
J710FNDDU1BRB2
J710FXXU5CRJ7
J710FNXXU5BRD5
J710FXXU4BRA2
And none of them worked.
I even tried with Samsung smart switch but when I enter the S/N it says its not correct.
Please any help?
m_alswairki said:
Hello, long story short.
I wanted to install TWRP on my J710FN and when I did so it wouldn't boot got stuck on the logo.
So, I tried to flash the stock firmware but the thing is my phone has a U6 binary.
I can't unbrick it using odin to flash the stock firmware because I cant find any U6 firmwares for my device.
I tried to flash these:
J701FXXU6BRH9
J710FNDDU1BRB2
J710FXXU5CRJ7
J710FNXXU5BRD5
J710FXXU4BRA2
And none of them worked.
I even tried with Samsung smart switch but when I enter the S/N it says its not correct.
Please any help?
Click to expand...
Click to collapse
Also, I cant get in the recovery mode.
and in the download mode it says:
Product Name: SM-J710F
Current Binary: Custom
System Status: Official
FRP Lock: Off
Secure Download: Enable
RP WEREV: B:6 K:1 S:2
m_alswairki said:
Also, I cant get in the recovery mode.
and in the download mode it says:
Product Name: SM-J710F
Current Binary: Custom
System Status: Official
FRP Lock: Off
Secure Download: Enable
RP WEREV: B:6 K:1 S:2
Click to expand...
Click to collapse
Same problem around me! - Finally any good new news for that?
J710FXXU6CSE1
I use this, yesterday this one repair my bootloop (black screen after logo), naw i cant find any possible to root my phone.
When u get binary 6 most important in wersion is J710FXXU---6---CSE1 (marked 6), this seys how meny binary it's. U need same number binnary or more binnary to flash phones corrects.
PS. - my model phone was change from SM-J710F to SM-J710FN but till naw all works fine.
If anyone get binnary 6 and got worked root files plis share.

Categories

Resources