Hi, new Android user here.
I was trying to root my Nexus S phone yesterday and I'm having problems. There is a lot of rooting guides out there and I used one from xda and also one from unlockr.com. Managed to root the phone ok (I think), but everytime I flash a custom ROM, the phone won't start at all, it just sits at the boot up screen and repeats itself.
So I'm thinking, I should just start over again. So I flash the stock ROM from xda back to 2.3.1. Everything seems ok, the phone starts up... but it's always stuck on airplane mode and the phone itself doesn't even show stuff like IMEI, mac address anymore.
So now I figure I've probably messed the phone up enough and need help lol. How do I go about reflashing the stock ROM and getting my Nexus back to out of the box condition (Stock ROM and no custom bootloader)?? Any guides or step by step instructions would be very helpful.
Thanks
Did you wipe before flashing roms?
Sent from my Nexus S c",)
Maybe flashing the KB2 modem would help that but the 9020a came stock with 2.3.3 and not 2.3.1 so that could be it...I'm not sure but that software wasn't meant at all for ours so it could be part of the problem. But if I was you I'd take a look at this thread wich has all the stock software for your phone. Make sure you wipe everything in clockework and then flash the stock rom. http://forum.xda-developers.com/showpost.php?p=13123996&postcount=39
dsixda uploaded the stock backup and the stock recovery, you can read more at that link, good luck hope it helps
You can download the full stock ROM from the link below:
http://goo.gl/8P8vl
Move the zip file to sdcard. Boot into recovery and flash the ROM. It should get you back to stock 2.3.4 ROM, all locked.
jungbum said:
You can download the full stock ROM from the link below:
Move the zip file to sdcard. Boot into recovery and flash the ROM. It should get you back to stock 2.3.4 ROM, all locked.
Click to expand...
Click to collapse
that did the trick. thanks everyone, now time to try rooting and flashing ROM again!
hrm lol now trying to update it to 2.3.4, it downloaded the update, but on reboot i get the white triangle with ! in it :\
this phone is so messed now
edit: well now everything is ok again, wiped data, flashed with CM7 and now it says 2.3.4, go figure.
Hello guys,
I installed CM11 a while ago on my Nexus 5. I had no trouble installing it through Cyanogenmods own installer, but now i want to install
the official rom again, so android 4.4.4 Kitkat. But when I want to flash it through TWRP i get the error that there is no MD5 file found.
I got the rom from the official site from Google.
I want to install the clean version of android again because i have some trouble with my battery and want to try if its still a problem with original software
installed.
So can you help me with this?
Thanks in advance.
Eelke91
When you after trouble shooting a battery issue you should wipe your phone and flash the stock image. Do not trouble shoot a battery issue with a custom ROM. Period. There are too many factors involved. And bugs can arise that won't be in a stock image.
I do want to flash to my stock image, but sadly i didnt backup so i want to manually install stock android kitkat.
Eelke91 said:
I do want to flash to my stock image, but sadly i didnt backup so i want to manually install stock android kitkat.
Click to expand...
Click to collapse
You don't have to wipe internal. Just Data and Cache. Go fastboot a stock image. If you aren't backing up Your Apps and you aren't clean flashing ROMs, that's why you are having so many issues. Never dirty flash a ROM unless your ROM Dev says otherwise.
Okay, but im pretty sure I wiped everything trying to install stock android. Atleast i got the message when i wanted to reboot that there was no OS installed..
So if its still possible to fastboot to my stock image can you tell me how to? I've now restored my phone to CM11, which was the last ROM i had installed, so i still can use my phone but its not the stock
image.
Eelke91 said:
Okay, but im pretty sure I wiped everything trying to install stock android. Atleast i got the message when i wanted to reboot that there was no OS installed..
So if its still possible to fastboot to my stock image can you tell me how to? I've now restored my phone to CM11, which was the last ROM i had installed, so i still can use my phone but its not the stock
image.
Click to expand...
Click to collapse
Google nexus factory image. Use that with fastboot.
Sent from my Nexus 5 using XDA Free mobile app
Eelke91 said:
Okay, but im pretty sure I wiped everything trying to install stock android. Atleast i got the message when i wanted to reboot that there was no OS installed..
So if its still possible to fastboot to my stock image can you tell me how to? I've now restored my phone to CM11, which was the last ROM i had installed, so i still can use my phone but its not the stock
image.
Click to expand...
Click to collapse
The instructions to flash a factory image are on the same page you download the image from. You need to flash it with fastboot, not recovery.
Okay i flashed it back to the stock os but still problems with my battery so i think its broken..
Eelke91 said:
Okay i flashed it back to the stock os but still problems with my battery so i think its broken..
Click to expand...
Click to collapse
Not likely. Probably just wakelocks. Go visit the battery help thread in my signature
Hey everyone, so I have from what I researched here is a "soft" bricked phone as my recovery mode (TWRP) and download mode works fine but no boot.
First let me say this is the Canadian version of the Note 5 SM-N920W8. I posted here because there is no forum for that version everything seems to be the same and posted under 920T version.
HISTORY OF THE PHONE:
It was a while ago that I rooted but let me describe to the best of my memory how my note 5 ended up in the state that it is in. So stock was lollipop 5.1.1. I flashed the skyhigh kernel which gave root access but had random reeboot issues which led me to flashing TWRP recovery so I could flash boot.img as an image file which did take away the random reeboot problem and removed that red error on startup "kernel is not SEANDROID enforcing". Life was good at this point! Everything worked great woth no issues. I greenified everything and underclocked the cpu with system tuner and used system app removed to manually all the bloatware as I didnt want to start using custom roms I stuck with the stock firmware. Part of the reason that I didnt want to use custom roms is because I started reading up on xposed framework, so I decided to flash it and give it a try. I read the xposed framework thread followed the download link to my version downloaded it and flashed with TWRP. Immediately after this was a bootloop.
TROUBLESHOOTING:
Unfortunately I had no backup in TWRP.. In a panic before researching I started flashing other kernels like arters kernel and I think space x whcih can be used on some note 5s.. which brought back that SEANDROID error message in the bootloop. I flashed the skyhigh kernel but flashing the boot.img didn't get rid of that error message again.
A friend of mine at work recommended that I just wipe everything and flash the stock firmware from sammobile.com with odin since I still have recovery mode then just re root. So I went into TWRP and wiped EVERYTHING. I think there was 4 or 5 boxes in twrp data wipe but I selected all the boxes. Now the phone doesn't even get the Samsung logo on boot or anything but download mode works so I flashed twrp again which loads up. I downloaded my version of the Samsung firmware which was about 1.6gb from sammobile.com. I open odin load the file that I extracted. A tar.md5 file which took longer than normal to load into the AP but I didn't change any settings or anything. Should I have? Because after I hit start it failed. I retried at least 3 times. Does this firmware contain all the AP CP and all the other boxes or do I need to find those separately? Should I just try a custom rom?
Im not sure what to do here I have a completely blank phone but twrp and download mode works so it recoverable right?
I read up on adb sideloader but didn't get too far.. is that worth trying for recovery in this case?
I also read a few threads on here for other samsung versions where they say to flash a PIT file with odin but they all say that it only works specifically for that phone and I couldn't find one for this version of the note 5.
I know the #1 rule here is to research before posting and Ive really made my best attempt to research on here and Google over the last few days but I really need my phone back. Any help is greatly appreciated.
re: phone won't boot
bloewen4 said:
Hey everyone, so I have from what I researched here is a "soft" bricked phone as my recovery mode (TWRP) and download mode works fine but no boot.
First let me say this is the Canadian version of the Note 5 SM-N920W8. I posted here because there is no forum for that version everything seems to be the same and posted under 920T version.
HISTORY OF THE PHONE:
It was a while ago that I rooted but let me describe to the best of my memory how my note 5 ended up in the state that it is in. So stock was lollipop 5.1.1. I flashed the skyhigh kernel which gave root access but had random reeboot issues which led me to flashing TWRP recovery so I could flash boot.img as an image file which did take away the random reeboot problem and removed that red error on startup "kernel is not SEANDROID enforcing". Life was good at this point! Everything worked great woth no issues. I greenified everything and underclocked the cpu with system tuner and used system app removed to manually all the bloatware as I didnt want to start using custom roms I stuck with the stock firmware. Part of the reason that I didnt want to use custom roms is because I started reading up on xposed framework, so I decided to flash it and give it a try. I read the xposed framework thread followed the download link to my version downloaded it and flashed with TWRP. Immediately after this was a bootloop.
TROUBLESHOOTING:
Unfortunately I had no backup in TWRP.. In a panic before researching I started flashing other kernels like arters kernel and I think space x whcih can be used on some note 5s.. which brought back that SEANDROID error message in the bootloop. I flashed the skyhigh kernel but flashing the boot.img didn't get rid of that error message again.
A friend of mine at work recommended that I just wipe everything and flash the stock firmware from sammobile.com with odin since I still have recovery mode then just re root. So I went into TWRP and wiped EVERYTHING. I think there was 4 or 5 boxes in twrp data wipe but I selected all the boxes. Now the phone doesn't even get the Samsung logo on boot or anything but download mode works so I flashed twrp again which loads up. I downloaded my version of the Samsung firmware which was about 1.6gb from sammobile.com. I open odin load the file that I extracted. A tar.md5 file which took longer than normal to load into the AP but I didn't change any settings or anything. Should I have? Because after I hit start it failed. I retried at least 3 times. Does this firmware contain all the AP CP and all the other boxes or do I need to find those separately? Should I just try a custom rom?
Im not sure what to do here I have a completely blank phone but twrp and download mode works so it recoverable right?
I read up on adb sideloader but didn't get too far.. is that worth trying for recovery in this case?
I also read a few threads on here for other samsung versions where they say to flash a PIT file with odin but they all say that it only works specifically for that phone and I couldn't find one for this version of the note 5.
I know the #1 rule here is to research before posting and Ive really made my best attempt to research on here and Google over the last few days but I really need my phone back. Any help is greatly appreciated.
Click to expand...
Click to collapse
If you have either a custom or stock rom installed or the official Samsung firmware installed
then it should be an easy fix, you must have flashed a incompatible kernel or perhaps you
deleted the kerned. (the phone will not boot without a kernel)
You need to find a compatible kernel and flash it using twrp recovery.
Here is a link you may want to try, it's for kernels for the Note 5 only:
http://forum.xda-developers.com/tmobile-galaxy-note5/orig-development
It might even be better if you were to Odin flash a fresh copy of your Note 5 specific
firmware using download mode, that's the surest way to get your phone working again.
Give it a try...
Good luck,
Have a great day!
Good luck!
Hi thanks for the reply! I did try that already unless flashing a stock firmware is different than putting it in AP as I flashed the kernel. Do I need to select some different optioms in odin since I data wiped everything and need all the necessary files to boot the phone? Oh and I did put the skyhigh kernel back on.
A friend of mine at work recommended that I just wipe everything and flash the stock firmware from sammobile.com with odin since I still have recovery mode then just re root. So I went into TWRP and wiped EVERYTHING. I think there was 4 or 5 boxes in twrp data wipe but I selected all the boxes. Now the phone doesn't even get the Samsung logo on boot or anything but download mode works so I flashed twrp again which loads up. I downloaded my version of the Samsung firmware which was about 1.6gb from sammobile.com. I open odin load the file that I extracted. A tar.md5 file which took longer than normal to load into the AP but I didn't change any settings or anything. Should I have? Because after I hit start it failed. I retried at least 3 times. Does this firmware contain all the AP CP and all the other boxes or do I need to find those separately? Should I just try a custom rom?
Click to expand...
Click to collapse
Unfortunately I had no backup in TWRP.. In a panic before researching I started flashing other kernels like arters kernel and I think space x whcih can be used on some note 5s.. which brought back that SEANDROID error message in the bootloop. I flashed the skyhigh kernel but flashing the boot.img didn't get rid of that error message again
Click to expand...
Click to collapse
re: not sure what you mean
bloewen4 said:
Hi thanks for the reply! I did try that already unless flashing a stock firmware is different than putting it in AP as I flashed the kernel. Do I need to select some different optioms in odin since I data wiped everything and need all the necessary files to boot the phone? Oh and I did put the skyhigh kernel back on.
Click to expand...
Click to collapse
Your best bet is to download the official Note 5 N920T odin flash firmware,
unzip it so you will end up with a TAR.MD5 file.
Then do a full wipe including system, data, cache, dalvik and last but not least
a factory reset in twrp recovery.
Once you do that your phone will be working properly again, flashing a kernel
or flashing firmware is the same process in odin. Use the AP slot.
And now I know what messed up your phone... it was as I posted before either
flashing the wrong kernel or the kernel got deleted who knows how.
That's all I can tell you except if you want the link to the official Samsung
N920T firmware here it is:
http://forum.xda-developers.com/tmo...t/rom-android-6-0-marshmallow-note-5-t3250812
The link also guides you thru the odin flashing process and other important things.
Good luck!
re: not sure what you mean
Quote:
Originally Posted by bloewen4
Hi thanks for the reply! I did try that already unless flashing a stock firmware is different than putting it in AP as I flashed the kernel. Do I need to select some different optioms in odin since I data wiped everything and need all the necessary files to boot the phone? Oh and I did put the skyhigh kernel back on.
Click to expand...
Click to collapse
I was researching some methods of flashing firmware to a completely wiped phone and read somewhere that there is a method to download all the files individually and put them into all the other sections in odin but I guess these tar.md5 files are a package of everything and one file is enough for a completely wiped phone? If all I need to k ow is to download that firmware unzip and flash in AP then awesome So longlong as they both have the same effect.
Your best bet is to download the official Note 5 N920T odin flash firmware,
unzip it so you will end up with a TAR.MD5 file.
Then do a full wipe including system, data, cache, dalvik and last but not least
a factory reset in twrp recovery.
Once you do that your phone will be working properly again, flashing a kernel
Click to expand...
Click to collapse
Just to clarify the order of this; first download that firmware via that link. 2nd wipe everything in twrp except for recovery so I can go back into twrp and factory reset in twrp? This alone will boot my phone before flashing the firmware? Or do I need to factory reset in twrp then flash that firmware in odin to get a boot? And is this custom firmware do I need to root again after I get boot?
Thanks for the link to that firmware going to be trying this right after work
bloewen4 said:
re: not sure what you mean
Quote:
Originally Posted by bloewen4
Hi thanks for the reply! I did try that already unless flashing a stock firmware is different than putting it in AP as I flashed the kernel. Do I need to select some different optioms in odin since I data wiped everything and need all the necessary files to boot the phone? Oh and I did put the skyhigh kernel back on.
I was researching some methods of flashing firmware to a completely wiped phone and read somewhere that there is a method to download all the files individually and put them into all the other sections in odin but I guess these tar.md5 files are a package of everything and one file is enough for a completely wiped phone? If all I need to k ow is to download that firmware unzip and flash in AP then awesome So longlong as they both have the same effect.
Your best bet is to download the official Note 5 N920T odin flash firmware,
unzip it so you will end up with a TAR.MD5 file.
Then do a full wipe including system, data, cache, dalvik and last but not least
a factory reset in twrp recovery.
Once you do that your phone will be working properly again, flashing a kernel
Just to clarify the order of this; first download that firmware via that link. 2nd wipe everything in twrp except for recovery so I can go back into twrp and factory reset in twrp? This alone will boot my phone before flashing the firmware? Or do I need to factory reset in twrp then flash that firmware in odin to get a boot? And is this custom firmware do I need to root again after I get boot?
Thanks for the link to that firmware going to be trying this right after work
Click to expand...
Click to collapse
Wait. You have a W8 variant. Odin won't flash a T variant on your W8 device, I don't believe. You need to download your carrier specific, hopefully 6.0.1 version, of the firmware for your specific carrier version, and flash that in the latest 3.10.7 version of odin.
---------- Post added at 09:21 PM ---------- Previous post was at 09:08 PM ----------
bloewen4 said:
re: not sure what you mean
Quote:
Originally Posted by bloewen4
Hi thanks for the reply! I did try that already unless flashing a stock firmware is different than putting it in AP as I flashed the kernel. Do I need to select some different optioms in odin since I data wiped everything and need all the necessary files to boot the phone? Oh and I did put the skyhigh kernel back on.
I was researching some methods of flashing firmware to a completely wiped phone and read somewhere that there is a method to download all the files individually and put them into all the other sections in odin but I guess these tar.md5 files are a package of everything and one file is enough for a completely wiped phone? If all I need to k ow is to download that firmware unzip and flash in AP then awesome So longlong as they both have the same effect.
Your best bet is to download the official Note 5 N920T odin flash firmware,
unzip it so you will end up with a TAR.MD5 file.
Then do a full wipe including system, data, cache, dalvik and last but not least
a factory reset in twrp recovery.
Once you do that your phone will be working properly again, flashing a kernel
Just to clarify the order of this; first download that firmware via that link. 2nd wipe everything in twrp except for recovery so I can go back into twrp and factory reset in twrp? This alone will boot my phone before flashing the firmware? Or do I need to factory reset in twrp then flash that firmware in odin to get a boot? And is this custom firmware do I need to root again after I get boot?
Thanks for the link to that firmware going to be trying this right after work
Click to expand...
Click to collapse
What carrier are you on? Go to sammobile and find out exactly what firmware is the latest for your variant on your carrier, for us T variants it's dpd1, but yours will be different, and sammobile is slow so if you can find a mirror somewhere for the stock firmware do that, download it...should be a tar.md5....if you get an error loading it you can often remove the .md5 from the extension...now first reboot recovery and you only need to wipe art/dalvik cache, system, data, cache, and if you want to internal storage but I normally don't...if you wipe efs and everything else you'll be sorry because only thing that will restore it is a full factory odin firmware flash...which is exactly what we're doing...so wipe those partitions then reboot download mode....launch odin and load your downloaded image into the AP slot. Make sure it's at least 3.10.7 version of Odin...when you connect the usb after rebooting to download mode you should see a green/blue box with COM:x (where x is a com port number on your pc) and it should say added...now flash it and wait until it finishes, it'll reboot maybe even a couple times, but it'll eventually make it to the setup screen- from here you can continue stock or flash twrp in odin then recovery flash a rooted kernel for stock rooted or continue with a custom rom, there's a fix in the note 5 gen section for making t/w8 devices work with call audio on intl roms and there's some stock Deodexed stuff at this point and certainly tekhd's mm rom...so from there the choices are yours...but your device is fine you just NEED to flash the correct stock firmware for your variant and use the latest version of odin with a factory usb cable and latest usb drivers from Samsung on your pc when you do it...you'll find links to all this stuff in most of the guides that are abundantly available...
Wait. You have a W8 variant. Odin won't flash a T variant on your W8 device, I don't believe. You need to download your carrier specific, hopefully 6.0.1 version, of the firmware for your specific carrier version, and flash that in the latest 3.10.7 version of odin.
Click to expand...
Click to collapse
I realize I have a W8 and hes providing the firmware for a T. I rooted with a kernel that was for a T version and everything worked fine. I researched rooting note 5 SM-N920W8 and they said do everything the same for the T version because theyre basically identical and isnt much info on the w8 version. So far Ive had no issues flashing everything designed for the T version on my W8. Actually Ive only tried flashing stock w8 firmware from.sammobile.com and got a fail in odin so now Ill try the version MisterJunkie provided me with for the T version unless considering all this you think I should still try a different firmware all together for the W8?
Misterjunky said:
Your best bet is to download the official Note 5 N920T odin flash firmware,
unzip it so you will end up with a TAR.MD5 file.
Then do a full wipe including system, data, cache, dalvik and last but not least
a factory reset in twrp recovery.
Once you do that your phone will be working properly again, flashing a kernel
or flashing firmware is the same process in odin. Use the AP slot.
And now I know what messed up your phone... it was as I posted before either
flashing the wrong kernel or the kernel got deleted who knows how.
That's all I can tell you except if you want the link to the official Samsung
N920T firmware here it is:
http://forum.xda-developers.com/tmo...t/rom-android-6-0-marshmallow-note-5-t3250812
The link also guides you thru the odin flashing process and other important things.
Good luck!
Click to expand...
Click to collapse
Bud, that's not the official tmo pd1 firmware, and I'm not sure if the leaked (alright it would likely run) would be the best here...plus he scares me when he says he cleared EVERYTHING cuz I'm thinking back to exactly how much twrp will wipe, but it's a lot so I fear he's going to need some partitions restored that are only going to come from a full pit file mapping...I don't believe official pd1 would flash in odin, nor would I recommend doing so- I would locate the most recently official firmware to ensure all partitions are restored, then if he doesn't have official mm support he can look into the leak, but if he had official for his variant and carrier that's his best bet to ensure 100% fix and give him a solid foundation to start from if he wants to root, rom, mod, etc
Not to discount your advice, I'd just hate to see him in a worse place than he is...which he's not even bricked YET...but he's starts screwing with wiping efs or messaging with csc stuff from different variants and he could back himself into a corner...
What carrier are you on? Go to sammobile and find out exactly what firmware is the latest for your variant on your carrier, for us T variants it's dpd1, but yours will be different, and sammobile is slow so if you can find a mirror somewhere for the stock firmware do that, download it...should be a tar.md5....if you get an error loading it you can often remove the .md5 from the extension...now first reboot recovery and you only need to wipe art/dalvik cache, system, data, cache, and if you want to internal storage but I normally don't...if you wipe efs and everything else you'll be sorry because only thing that will restore it is a full factory odin firmware flash...which is exactly what we're doing...so wipe those partitions then reboot download mode....launch odin and load your downloaded image into the AP slot. Make sure it's at least 3.10.7 version of Odin...when you connect the usb after rebooting to download mode you should see a green/blue box with COM:x (where x is a com port number on your pc) and it should say added...now flash it and wait until it finishes, it'll reboot maybe even a couple times, but it'll eventually make it to the setup screen- from here you can continue stock or flash twrp in odin then recovery flash a rooted kernel for stock rooted or continue with a custom rom, there's a fix in the note 5 gen section for making t/w8 devices work with call audio on intl roms and there's some stock Deodexed stuff at this point and certainly tekhd's mm rom...so from there the choices are yours...but your device is fine you just NEED to flash the correct stock firmware for your variant and use the latest version of odin with a factory usb cable and latest usb drivers from Samsung on your pc when you do it...you'll find links to all this stuff in most of the guides that are abundantly available...
Click to expand...
Click to collapse
My carrier is Rogers. I did goto sammobile.com already and downloaded and flashed what I thought was the current stock firmware for my 920w8, but I flashed without wiping all data as previously stated. Maybe doing this will allow my firmware to flash? Will try when Im home from work. Will also post the link from sammobile.com for the exact firmware I download just to verify ots the right one.
Yeah I literally wiped everything I checked all the boxes and I remember having to manually type y e s to proceed so yeah pretty serious wipe lol.
I have the latest version of odin 3.10.7 and tried installing drivers on my pc said theyre already installed.
When I connect my phone to usb in download mode it says com:4
I thought also that just flashing the stock firmware would be the solution since I get download mode and twrp I just have a blank phone but as I said I did get the stock firmware from sammobile.com and try but it failed. Maybe I grabbed the wrong one but it looked pretty straightforward. Maybe with MM coming out Wednesday for rogers note 5 Im downloading the wrong version.
Im worried like you wrote earlier that I deleted too much with twrp if I needing mapping partitions and PIT files I will need some serious help that stuff is beyond me.
Go to sammobile and find out exactly what firmware is the latest for your variant on your carrier, for us T variants it's dpd1, but yours will be different, and sammobile is slow so if you can find a mirror somewhere for the stock firmware do that, download it...should be a tar.md5....if you get an error loading it you can often remove the .md5 from the extension...now first reboot recovery and you only need to wipe art/dalvik cache, system, data, cache, and if you want to internal storage but I normally don't...if you wipe efs and everything else you'll be sorry because only thing that will restore it is a full factory odin firmware flash...which is exactly what we're doing...so wipe those partitions then reboot download mode....launch odin and load your downloaded image into the AP slot. Make sure it's at least 3.10.7 version of Odin...when you connect the usb after rebooting to download mode you should see a green/blue box with COM:x (where x is a com port number on your pc) and it should say added...now flash it and wait until it finishes, it'll reboot maybe even a couple times, but it'll eventually make it to the setup screen- from here you can continue stock or flash twrp in odin then recovery flash a rooted kernel for stock rooted or continue with a custom rom
Click to expand...
Click to collapse
Goodmorning, as I mentioned I would try this right after work. Heres what I did.. I verified that I had the 3.10.7 version of odin which I do, checked drivers on pc which I have. I re downloaded the firmware from here http://www.sammobile.com/firmwares/database/SM-N920W8/ Its was the Canadian Rogers version 5.1.1 near the bottom as mm isnt out for rogers yet.. Oh and I checked my cable ot connected another device to my PC.. so after all this I went into twrp wiped everything you mentioned. After that I was looking for the factory reset option in twrp but couldn't find anywhere only restore which I have no rom backups made. Do I need this step?
Went into download mode pressed vol up.. opened odin 3.10.7. I did notice a change after wiping. Its now says com:6 instead of com:4 if that means anything.. I loaded the firmware into AP it took a while to load but it did without errors. Flashed and failed If you need I can copy the error message from odin in here tonight.
Do you think I need to remap partitions as you said earlier? Getting PIT files? Im lost here... appreciate any help
Still with a blank phone, any ideas?
Or if anyone could direct me to another thread that might be useful for re mapping partitions?
Have you tried flashing twrp again in Odin?
I hit too many buttons before when wiping. It even erased my recovery.
Once I had recovery again I could Odin flash the official firmware.
Could try Philz recovery as well.
Sent from my SM-N920T using XDA-Developers mobile app
Yeah I did try that heres the link where I got the firmware and yeah twrp is on there.
Goodmorning, as I mentioned I would try this right after work. Heres what I did.. I verified that I had the 3.10.7 version of odin which I do, checked drivers on pc which I have. I re downloaded the firmware from here http://www.sammobile.com/firmwares/database/SM-N920W8/ Its was the Canadian Rogers version 5.1.1 near the bottom as mm isnt out for rogers yet.. Oh and I checked my cable ot connected another device to my PC.. so after all this I went into twrp wiped everything you mentioned. After that I was looking for the factory reset option in twrp but couldn't find anywhere only restore which I have no rom backups made. Do I need this step?
Went into download mode pressed vol up.. opened odin 3.10.7. I did notice a change after wiping. Its now says com:6 instead of com:4 if that means anything.. I loaded the firmware into AP it took a while to load but it did without errors. Flashed and failed If you need I can copy the error message from odin in here tonight.
Click to expand...
Click to collapse
bloewen4 said:
Yeah I did try that heres the link where I got the firmware and yeah twrp is on there.
Click to expand...
Click to collapse
Since you have twrp on the phone.. Tap to create a backup even if there's no system on it so that you can at least make it create the folder.. Try using adb to push a ROM and kernel to the phone so you can use twrp to flash it. If you can get into the phones storage using Windows then just drop a ROM and kernel for your device in the folder and then use twrp to flash.
By the way.. Use the SkyHigh kernel.
Follow the directions to a T!!
http://forum.xda-developers.com/note5/orig-development/kernel-skyhigh-tw-6-0-1-kernel-t3321646
If you can get into the phones storage using Windows then just drop a ROM and kernel for your device in the folder and then use twrp to flash.
Click to expand...
Click to collapse
I did try immediately to connect with Windows to my phone so I could try flashing stock firmware with twrp but its currently not allowing me access to view storage on Windows though it does connect with odin saying com:6.
Since you have twrp on the phone.. Tap to create a backup even if there's no system on it so that you can at least make it create the folder..
Click to expand...
Click to collapse
I will do this as soon as I am home from work. Will this perhaps allow access with Windows and/or adb sideloader?
Try using adb to push a ROM and kernel to the phone so you can use twrp to flash it.
Click to expand...
Click to collapse
I will be researching how to do this. Have you any threads to learn adb? So basically this will allow me to put ROMS or other files into the internal memory?
By the way.. Use the SkyHigh kernel.
Follow the directions to a T!!
http://forum.xda-developers.com/note...ernel-t3321646
Click to expand...
Click to collapse
Is this the right kernel for SM-N920W8?
* SAME kernel for ALL supported variant !!
** If other party cannot hear voice when on speaker phone ** Then read Post #636
SM-N920 C / CD / G / i [ v3.2 ]
SM-N9200_HK [ v3.2 ]
Click to expand...
Click to collapse
Also Marshmellow isnt out officially for SM-N920W8 so Ill need a kernel for lollipop 5.1.1 unless you suggest to wait for marshmellow then try a mm kernel?
Thanks for helping!
How about this adb sideloader does anyone think that will work to load the firmware? If so any good threads to guode me?
What did you end up doing? I have a similar problem except no recovery mode, just download mode for Odin.
bloewen4 said:
Goodmorning, as I mentioned I would try this right after work. Heres what I did.. I verified that I had the 3.10.7 version of odin which I do, checked drivers on pc which I have. I re downloaded the firmware from here http://www.sammobile.com/firmwares/database/SM-N920W8/ Its was the Canadian Rogers version 5.1.1 near the bottom as mm isnt out for rogers yet.. Oh and I checked my cable ot connected another device to my PC.. so after all this I went into twrp wiped everything you mentioned. After that I was looking for the factory reset option in twrp but couldn't find anywhere only restore which I have no rom backups made. Do I need this step?
Went into download mode pressed vol up.. opened odin 3.10.7. I did notice a change after wiping. Its now says com:6 instead of com:4 if that means anything.. I loaded the firmware into AP it took a while to load but it did without errors. Flashed and failed If you need I can copy the error message from odin in here tonight.
Do you think I need to remap partitions as you said earlier? Getting PIT files? Im lost here... appreciate any help
Click to expand...
Click to collapse
Where did you get your firmware from?
Why oh why did I bother reading through this entire thread, with intentions to help OP. Lol I didnt realize the date till the last post.
Hello all,
I need some help with this old Atrix 2. It's been sitting in a drawer for a while, and I haven't touched it for like a year at least. Apparently back then I had dual-booted stock and another ROM using BMM (Bootmenu Manager). Well now I need to use it and I thought the best thing to do would be fastboot flash the stock ROM, so I did that from the bootloader and it didn't change anything. So I went into BMM and deleted the second ROM (in slot 3), then did a factory reset on the stock ROM through fastboot.
Now I can't get any slots to work besides stock, and the stock ROM has zero bytes available for user data. meaning I can't install the BMM app to remove BMM.
When trying to use another slot, I can create the virtual partitions, but after a reboot it can't find them anymore...
From recovery I can't even mount /data. I'm not sure how to fix this.
You should flash the stock ROM using RSD.
Maybe you will need some resources and basic guide here
PhoenixNghi said:
You should flash the stock ROM using RSD.
Maybe you will need some resources and basic guide here
Click to expand...
Click to collapse
Downloading the file now, will let you know how it goes. Sorry for the late reply.