Hi, recently the wifi on my Nexus 5 stopped working like it should and, after lots of reboots, resets & co., I completely wiped it and flashed Nougat (Dark Rom). It gave a little hope but stopped working again soon after, so I concluded it must be hardware related. After some research I found this thread here on XDA that suggests some DIY solutions. Before opening my poor phone and cooking its motherboard as one of the methods describes, I thought that maybe it would be possible to use an external wifi dongle such as this, plugged in via an OTG cable (thought I had after successfully using my pc connected via OTG to the phone and via wifi to the router). I'm currently on Dark Rom 7.1.1, rooted with Magisk.
Does someone know if something like this is possible?
Why not open it and see if a connection is loose. Would not recommend cooking it
All the pins and cables are in place
If someone is expert enough to tell me if the dongle idea is doable it would be higly appreciated
Dark rom over here and same issue too, weird
Related
Hello suddenly my nexus s stopped connecting with data with the pc it only charges, tried with 3 diffrent computers with diffrent os , no menu popping on nexus and nothing connected on the computer(like i didnt connect anything), i removed the battery left it for some time installed stock rom still nothing.It was acting normally for a second and the other it stopped any help appreciated!
Are you sure you're using the cable that came with the phone? I have an LG Wink featurephone here that uses the same connector at the phone end -- its cable will charge my Nexus S (using the computer, obviously, but also when used with either the LG or Samsung charger) but no USB connection happens when I use it. Only the cable that came with my Nexus S provides a USB connection when I connect to the computer. I guess there are pinout differences between the two cables.
If you're sure you're using the right cable, I would guess that it's gone bad if it doesn't work on any computer. You can buy an (overpriced) replacement from Samsung or maybe a cheaper one on eBay or at a retail store. If the latter, be sure the seller lists it as compatible with the Nexus S.
it happened with the original cable ppfff i dont know...
same problem
stavros86 said:
Hello suddenly my nexus s stopped connecting with data with the pc it only charges, tried with 3 diffrent computers with diffrent os , no menu popping on nexus and nothing connected on the computer(like i didnt connect anything), i removed the battery left it for some time installed stock rom still nothing.It was acting normally for a second and the other it stopped any help appreciated!
Click to expand...
Click to collapse
Hi
I have the same problem
I have no idea what the problem could be.
We are not alone with this problem: code.google.com/p/android/issues/detail?id=13553
Now installed stock rom as well but still the same problem.
If i starting the NS in the bootloader mode the phone is not recognized by the computer.
It would be great, if someone knows a solution!
polandy said:
Hi
I have the same problem
I have no idea what the problem could be.
We are not alone with this problem: code.google.com/p/android/issues/detail?id=13553
Now installed stock rom as well but still the same problem.
If i starting the NS in the bootloader mode the phone is not recognized by the computer.
It would be great, if someone knows a solution!
Click to expand...
Click to collapse
I've been trying to get help with this for weeks. No one is even responding to my posts. I thought it was something OBSURDLY simple, such that people didn't even want to waste their time responding to me.
Seeing same problem, No connetion via USB
Posted problem in General,, http://forum.xda-developers.com/showthread.php?t=1104245
Tried different cords, different computers and operating systems,, did cold start several times on phone (removed battery) still no luck, I am running totally stock
Curious do any of you have the Google Music Beta?? (maybe a over zealous rights thing?)
just tried it with a Win 7 machine that had never seen it before and it said it could not recognize the device,, me thinks that the MS device driver DB is messed up buy some recent Win update??
i sent it to samsung to change my usb slot because after connecting to pc and nothing happen when i went to charge the phone it took 5 hours to get to 30% so iam almost sure that mini usb slot malfunctions
stavros86 said:
i sent it to samsung to change my usb slot because after connecting to pc and nothing happen when i went to charge the phone it took 5 hours to get to 30% so iam almost sure that mini usb slot malfunctions
Click to expand...
Click to collapse
My phone charges just fine. And my USB connectivity was fine until I manually installed 2.3.4.
~I had usb connection problems after upgrade to 2.3.4 a bit different but I managed to get the USB back by formatting the SD card.
see here
Acnescar said:
~I had usb connection problems after upgrade to 2.3.4 a bit different but I managed to get the USB back by formatting the SD card.
see here
Click to expand...
Click to collapse
I was on 2.3.3 when this happened, i tried to flash 2.3.4 then and again it didnt work but the strange thing is that when i was moving the mini usb the first times up and down it was shown for a moment as a broken usb device.Then this stopped and was not shown at all on the computer and finally the phone charged super slow when connected to electricity
Beginning to believe that it is a physical prob with USB connector on phone. It seems to start/stop charging when wiggling usb on phone but no mounting. Doe anyone know best way to resolve , T-mobile but bought from Best Buy? so to Best Buy? FOR SUPPORT /EXCHANGE? suggestions?
I've seen loose connections before. My suggestion ain't the cheapest but the plug, on the cable end, shouldn't wiggle. I went to a corporate sprint store, the ones that actually have working display phones, and got their usb to micro usb data cable. The thing with that cable is when you plug it in the phone side, it goes into the jack firmly. You can almost feel the little locking tabs click into place. There should be no play or wiggle with that cable as long as there's no damage or abuse with the jack on the phone. IMO, that's a good data cable. It's never given me problems before.
Also, sometimes the cable is only wired for charging. A true data cable will be wired correctly and be able to both charge and transfer data. Usually the cables that come with the phone are crap quality. I don't know if my suggestion will help but it won't hurt to have a good cable for data transfer and flashing. The last thing you want is a flaky connection from a cheap cable when you're flashing roms. Russian roulette with bricking a phone in a worse case situation.
Did you try reboot the computer and the phone? How about a different usb port? How about unplug any other usb device in case it's conflicting for some unknown reason? It sounds like so many people with windows 7 are having problems. Usually always happens with a new os that's released. Xp, for flashing devices and programming different hardware devices, has never given of a problem. I have a small partition with xp on it just for that purpose only.
off to Samsung for repair for me...
After time on phone with them and a factory reset belief is that the usb connector is defective. BTW Best Buy just hands off to Samsung 1-800 #
So Back to a barely functional G-1 for a while, glad I could find it!
So is Samsung or the carriers replacing or fixing units?
My USB data died shortly after 2.3.4 ota update.
Wifi FTP is fine for data transfer but I want USB debug to work...
Shame on google and Samsung, this bug has been around for months.
no shame on anyone...
I went through a factory reset with Samsung on phone that isolated the problem to what is apparently a loose usb connector, nothing to do with software... only hassle is sending it in for repair, as` mentioned problem needs to be dealt with Samsung customer service (not carrier or Best Buy), they were fine on phone...
I have a SCH-I915 (Verizon) which is not recognized by any machine that it gets plugged into. There's no unknown device, no beep of a usb connection, it does beep like a charger has been connected (and gets the red x on the battery icon, indicating the amperage is insufficient), but the PC doesn't recognize there's an interactive device on the other end. I have spent 3 days combing the forums. I can assure everyone, it is NOT a driver issue. For one thing, the same laptop that flashed the wrong firmware and unlocked the bootloader is among those who can't see it. It also isn't visible to the best buy samsung rep or he'd have flashed it for me. I've also used anycut to manually select mass storage or samsung kies. Neither work. After reading many, many MANY posts on devices not being recognized, it seemed to me the ultimate fix for most of the people with these symptoms was a new cable. I just bought a cable and it's the same. The original does me no good, neither does the new one (which is an insignia from best buy). The maddening thng is, it was working FINE (apart from being unusable...but it was able to be connected to any way you like) just a few days ago. It was the factory reset from within the 4.1.2 OS that seems to have changed something. My idea (which may be entirely off base, since I don't actually know the USB protocols is, the tablet gets plugged in and either is supposed to say "I'm here" or the PC asks "who are you?" After that would be steps on establishing what device it is, etc... I think this initial handshake is what's broken. The PC thinks it's got a usb fan or whatever, the tablet thinks it's connected to a crappy charger.
So I've got a couple questions
1) Do they make charging cables which are distinct from the data transfer cables?
2) Has anyone used one of these insignia cables? Was it fine for you?
3) Is there any other nuclear option I can deploy myself? I don't have much faith in those best buy guys. (On a side note, I was allowed to use the guy's laptop to try and get it to work and if I had had a thumb drive, I'd have all the cool imaging software they have...but it was not to be.)
Does it shows up when connected in recovery or download mode?
Sent from my Nexus 4 using XDA Premium HD app
No it doesn't
No matter the computer I'm attaching to, nor whether it's in download, recovery, or fully up, the connection appears to only be seen by one side.
Hi.
I'm kinda new to this and was wondering if anyone has had similar problem. My USB port only seems to work as a charger (slowly). No computer recognises the phone. It only displays USB device not recognised. I know for sure it's not the computer(s) as my S7 works fine.
My major problem is: is there a way to flash phone without USB cable?? My phone status is displaying as "custom" and alas, will not let me update OTA.
I think it may be a software problem... But I'm no expert...
I'd appreciate any help from anyone who can suggest a remedy.
regards and good luck!
:crying:
Software Problem??
I'm just wanting to know if it's possible that a software issue is causing the USB problems??? or is it hardware related.
It no longer uses the fast-charge method, just the regular slow charge... I've noticed that charging takes longer than usual, even if not using the adaptive fast charging plug.... Just a thought...
go raibh mait agat!
Same here, think it's s faulty USB port on phone?
Sent from my Nexus 7 using XDA Free mobile app
HI Guys,
Looking for some help. I have an HTC U11 on Oreo. Recently installed a Kenwood 7704S Android Auto HU.
Installed Android Auto app via google play, as well as latest version direct from Google. Phone is just not detected using the original USB C cable BUT the phone is charging, all other functions work via the Android Auto app without being cable connected. Short of installing older AA apk versions I am at a loss. I have tested unit with a iphone and Apple Car Play launches fine so it is not a a HU issue as I assumed. I had used this unit with a P10 Plus and it worked but I had intermittent issue with it as well but with the U11 it has just quit launching all together. I have reset phone to factory and tried fresh, no success. I have enabled Developer mode and enable USB debugging and selected MTP Protocol still no luck. I thought perhaps Nova Launcher may have been the culprit but not the issue once reverting to Sense as launcher. I have enabled AA permissions so thats set up correct.
Anyone experience U11 Android auto issues, super frustrating and don't want to run a custom rom just yet or possibly sell phone and find a working Android phone, last OP3 worked with previous Sony XAV-AX100 but I sold that unit wanting an extra USB port. Suggestions welcome cause I am at wits end beside trying other AA versions from earlier dates or rolling back to Nougat, that I have not yet tried. Phone has worked on Oreo and I got it with Oreo but I was experience intermitent connectivity. I can't see it being the USB C port but I did test the unit at the audio store where I bought my 7704S on their demo 9904S and same issue the phone charged but would not launch AA on the HU so it seems to be a hardware/software issue with the U11 itself
I don't have a Kenwood head unit but I have a pioneer NEX-4100 with Android Auto & Apple Carplay.
I just went out to the garage hooked up my wife's (I don't have one) HTC U11 (64GB USA Version) and successfully configured & established an Android Auto connection to the head unit. Ran through the menus and it functioned properly.
I used the USB C cable that came with my LeeCo S3 phone and it worked with the HTC U11. I did not try to use the HTC U11 cable as I don't know where the ball and chain keeps it. But I know cable(s) and Android Auto make a difference.
The U11 was on the latest Oreo 8.0 stock rom and is not rooted.
Hope that helps....
Also, on my Pioneer head unit, I have to specifically enable either Apple or Android Auto in the menu. So if it's not setup to use AA then it won't work until I enable it. This is only done once or until you need to use the Carplay side. Additionally, There are two USB connectors on my head unit with one connector specific to the iPhone and the other specific to the AA phone.
Endosmok said:
I don't have a Kenwood head unit but I have a pioneer NEX-4100 with Android Auto & Apple Carplay.
I just went out to the garage hooked up my wife's (I don't have one) HTC U11 (64GB USA Version) and successfully configured & established an Android Auto connection to the head unit. Ran through the menus and it functioned properly.
I used the USB C cable that came with my LeeCo S3 phone and it worked with the HTC U11. I did not try to use the HTC U11 cable as I don't know where the ball and chain keeps it. But I know cable(s) and Android Auto make a difference.
The U11 was on the latest Oreo 8.0 stock rom and is not rooted.
Hope that helps....
Also, on my Pioneer head unit, I have to specifically enable either Apple or Android Auto in the menu. So if it's not setup to use AA then it won't work until I enable it. This is only done once or until you need to use the Carplay side. Additionally, There are two USB connectors on my head unit with one connector specific to the iPhone and the other specific to the AA phone.
Click to expand...
Click to collapse
Thanks for your reply and taking the time to test your wifes HTC u11 on your Pio system. I am stumped still with no luck, with the Kenwood there is no selecting either the AA or Car Play in menu system will just launch automatically upon connection of device. The oddest thing is when I tested my sons 7 Plus it worked flawlessly but following I tried with my HTC U11 using the factory cable and no success. I plan to buy a better USB C cable and give it one last try because I am stumped and frustrated. Mine is USA version as well 64GB. Everything works as it should aside from the system being able to detect the phone and yet the deck rapid charges the device through either USB connection.
I tried another USB C cable and this one gives "an access error of the USB device has occurred" What makes this story even odder is my phone is not detected by my pc either so I am really starting to question if there is an issue with the USB C port, it charges fine but from my understanding data flows via different contacts within the port. This is the only sensible reason at this point. At this point as much as I like the U11 I am considering an alternative Android phone. When i looked up this access error there are lots of people with the issue and Kenwood decks as well as others... Seems it can be a hit or miss with this newest connection
https://productforums.google.com/forum/#!topic/android-auto/az_IM9QyzI4
cisco kidd said:
Thanks for your reply and taking the time to test your wifes HTC u11 on your Pio system. I am stumped still with no luck, with the Kenwood there is no selecting either the AA or Car Play in menu system will just launch automatically upon connection of device. The oddest thing is when I tested my sons 7 Plus it worked flawlessly but following I tried with my HTC U11 using the factory cable and no success. I plan to buy a better USB C cable and give it one last try because I am stumped and frustrated. Mine is USA version as well 64GB. Everything works as it should aside from the system being able to detect the phone and yet the deck rapid charges the device through either USB connection.
I tried another USB C cable and this one gives "an access error of the USB device has occurred" What makes this story even odder is my phone is not detected by my pc either so I am really starting to question if there is an issue with the USB C port, it charges fine but from my understanding data flows via different contacts within the port. This is the only sensible reason at this point. At this point as much as I like the U11 I am considering an alternative Android phone. When i looked up this access error there are lots of people with the issue and Kenwood decks as well as others... Seems it can be a hit or miss with this newest connection
Click to expand...
Click to collapse
I have been fighting cables and Android Auto for a long time now and finally found my problem which is so dumb to be almost unbelievable. Had a friend suggest this and it was the problem. I keep my phone in my pocket. It picks up lint in the USB C connector. And slowly over time. I took a toothpick and cleaned out the connector. It gets packed in, so takes a while to completely clean it out. I was shocked how much came out. After doing this, all my USB errors disappeared and problems with various cables disappeared as well. Duh, the common denominator was always the phone, not the cable. But it was curious that some cables seemed to work better than others. I feel so dumb, I actually returned this model phone in the first year under warranty because it finally stopped charging by cable. Got another phone and a wireless charger, but my second phone started acting up again and finally just refused to work a few months ago with Android Auto. Now everything is working great again.
I have LG G6 and Kenwood 7704 HU.
Chris
I'm having the same problem.
I have a pioneer 4200 nex, and can't connect to android auto. Worked perfect with previous m9, but since I bought U11, nada.
I'd be curious to see if anyone can help figure this one out. I drive a lot for work so it was nice seeing Maps on the screen.
Check the Kenwood website and see if there's a mention of unit having problems with type C connectivity.
pioneerelectronics.com/PUSA/Car/NEX/Android+Auto+not+working+for+newer+USB+Type-C+phones+(including+Pixel
While researching about me pioneer HU, this is what I found out. I suppose you can use the recommended cables as listed in the pioneer website as it sounds more of a cable problem than anything else.
I will post more once my new type A cable comes in. Sux I gotta go back in the dash to plug it in though. I still have my OEM type C so that should work.
Hi everyone i'm facing this problem since july now, the issue is that the pixel 3 usb-c port works only with charge and nothing else, that means it doesn't work with pixel buds, doesn't work with other headphones with jack adapter, no OTG devices work, and finally PC connection wont work either.
I've tried everything possible from cleaning the port to factory resetting the phone, with no results.
Online there are few google forum threads about the problem but without any fix, so i've tried to RMA from google but even if i have still warranty, i should have paid 106€ cause my back glass cover is broken. Since i didn't want to pay that much to fix the back i bought the usb-c port replacement and i fixed it myself, i thought it would have fix it but surprisingly it didn't and i have still the same issue so working charge but no any other usb-c connection.
At this far i'm thinking it's a software problem but even Android 11 with last october patch didn't solved it , still the same: usb preferences greyed out when connecting to a PC ( tried different PC: Windows 10, Windows 7 and even Linux) same result.
Update:
I have more evidences which lead to this point, a few days ago i tried to connect my Pixel C to the laptop to transfer some files and it is suddenly showing the same problem of the Pixel 3, i have to state that the Pixel C was running an Android 9 ROM so it fits perfectly in all the reported issues about it precisely that the problem pops out since Android 9 and there seems not to be any fix for this even in the last Android 11 patch.
I also started getting the same issue. Maybe I didn't notice for a long time because I was using a Bluetooth headset for a long time. And today when I checked, it was not working for me. Charging works and pc connection is also okay for the moment. Surprised to see no one has responded to this.
This happened to me every now and then. I was able to clear it by turning USB debugging on (under developer options) then connecting it to my laptop. Unplugged it and turned USB debugging back off.