OK, heres the deal..
Yesterday I managed to crack the bottom-left corner of my BA screen (damn medkit shifted onto it in my car glovebox ).
As i was checking to see how much of the screen was still responsive (seemed OK, still usable, only the 'New' button and the bottom item of the menu didnt work) the battery died (as in completely, hard reset died)..
So i plug in the power, and start the familiar initial setup. I get to the callibrate screen screen and am unable to continue..
So my question is: Is there any way to bypass the calibrate screen section of the initial setup? Im pretty sure enough of the screen still works for the device to function, if only i could get past this damned calibration screen..
Clearly i cannot bypass it completely, as the screen does need to be calibrated - but is there any way I can recover my BA?
Cheers All
Check out this thread:
http://forum.xda-developers.com/viewtopic.php?t=1910
or this one:
http://forum.xda-developers.com/viewtopic.php?t=6855
Also, if you can still see the image it means that only the digitizer (touch sensitive part) is broken, and not the screen so it shouldn't cost to much to replace.
And remember - search is your friend! :wink:
This might be a bit toooo late, but just in case some one is stuck with a broken screen as dabs and I were.
I received a k-jam (lucky me, it was for free) with a broken touch screen, it was left uncharged for a long time so after charging it, it entered the unwelcomed welcome mode (you know, align, copy, time zone ...) and there were no way of passing this part of initialization.
I had to do some search over the net, and I found a good article here ((Can I use a PDA that has a broken touch screen)) http://www.pocketpcmag.com/blogs/index.php?m=200510 which advised the use of "RemoteCalibration.exe" directly from the pc. This killed the welcome.exe program and I managed to re-use the K-jam again. The only draw back about this way is that I will have to connect the K-jam to a pc every time I hard reset, I hope there is a way to do the same action via mini sd cards.
After that, I installed fakecursor (but I'm looking for a better sw to emulate the touch screen function as this one cancels most hardware buttons on the devise) but at the moment, I'm using all the k-jam's functions.
Hope this would be of help to some one out there
Touch screen in my Eten M810 is broken. I have accidentally locked my device and I can't unlock it without touch screen. Is there a possibility to unlock it with some shortcut. If hard reset is the only solution can I omit calibrating of screen during installing system?
Shot in the dark here. You are referring to the winmo lock? But with my 6.1 device I can either touch screen or hold end call button for 2 seconds.
good day.
you can use mymobiler for manage the phone in your pc..
just try.. lucky..
numaverick, you're my god! I've unlocked my device!
I have zte blade aka dell xcd35 ( rooted with z4root ) with custom rom eco-cm9-20130324-stable-blade rom
from last two years
as i was trying new new roms on my blade i loose touchsccreen sence ( down side 3/4 part of screen is not working ) only upper 1 inch area is working
I have tried many of roms but no one works
although the phone is still working all
just have to hold the one finger where want to touch and touch the area is still working then i will work ( is it means my screen hardware isn't faulty ???)
i use it only for incoming calls pickup calls by volume and ends with power button
i remember i have used a tool for screen calibration ( Nook Screen Recalibrate )
is there any solution ???
please help me
My screen is cracked since few mounths. After the drop the touch screen didn't work for half of the screen, the half, in orhizzontal, where the screen is cracked. Tonight I tried here (Sony eSupport - Electronics - Drivers & Software) panel calibration tool, now the touch screen works everywhere and now it's the situazion is worst then before. The cracked screen press itself and I can't use the tablet. Now I disabled touch screen in device manager, but my SP3 without touch is very sad I want to ask if there is the possibility to disable only part of the touch screen, the screen is cracked only for a few cm, I could use it completely even without that portion of the screen. Thanks.
I doubt you woudl be able to disable part of it, it would be a case of just disabling it full stop as it'll get worse..
So my phone droped and damaged my phone a bit. My touch screen is okey but im geting random touches on the left corner of the phone. Is there any app that can disable touch on that corner and not all the screen?