Hi everyone,
On my S6 all of a sudden I got the blue screen saying that I need to connect it with Smart Switch for a Recovery. Smart Switch wont recognize the S6. So I tried with Odin to flash a new stock firmware but I keep getting NAND Write Operation Failed after boots.img.
This phone hasnt been used for several months, but I want to recover it because there are very valuable holiday photos on it. So the internal memory cant be wiped. I a hoping that flashing a stock rom will make the phone boot again.
Odin Log
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have tried various stock roms and also various usb cables. The phone was last used in the 1st week of october, so the first rom (6.0.1.) I tried to flash was the lastest prior to it (september). After that I tried August and then I jumped in time to January because I read about a rollback isnt possible. After January (the last month for 6.0.1) I decided to try the latest stock rom avaible for 7.0.
My phone is unbranded but just incase I also tried the 3 branded roms for my country (the netherlands) for vodafone, T-Mobile and Ben. All tried roms gave the same response as stated above.
I also tried to unpack the tar file and use TarCreator to create a separate Tar file for each .img. Then flash them 1 by 1 in Odin. But again the same Nand write error is given.
Odin versions that I used: 1.85 and 1.10.6
Things I didnt try yet:
Pit I kept the Pit empty on Odin. After some research it still wasnt clear to me if using a stock Pit file would not wipe the internal memory.
I hope some here could clarify that. And if I can safely use a Pit file, do i then 1st run the pit file, restart Odin and then flash the Rom. Or can i just enter them both at the same time/session?
BootloaderI found some info that said that boatloader might be corrupted? Again also about that I couldnt find a clear answer if it would wipe the internal memory. Also I am not sure where to find good boatloader files.
I've spend now 3 days on google searching solutions and trying different roms and I dont know what to try next. I hope one of the experts on this forum might know another solution or can give a clear answer on the Pit or Boatloader options.
Kind regards.
Try with Newest ODIN (3.12.7) instead of a Very Old ODIN for at Android 2.2 only (3.08) -> thedroidguru.com/download-latest-odin-odin3-all-versions-full-collection
Illutorium said:
Try with Newest ODIN (3.12.7) instead of a Very Old ODIN for at Android 2.2 only (3.08) -> thedroidguru.com/download-latest-odin-odin3-all-versions-full-collection
Click to expand...
Click to collapse
Thanks! Somehow I was under the assumption that 3,18 was higher but I see the mistake now.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1207)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
After boot.img the phone turns off black screen, then goes back to the smart switch recovery screen. Gave it a few more tries and tried with Auto Boot enable and disabled. After the last attempt the phone screen stays black, even when plugged into the charger
Also Ive noticed that the right side of the phone now gets very hot when plugged in.
The screen still stays black. The phone wont even turn on anymore :/
Flashing stock will wipe your data anyway. There is a chance it won't format your internal storage though. If there is VERY important data, you should go to a professional data recovery service.
Related
Hello guys,
i have problem with my P6810 16gb Wifi tablet, the problem started when i flashed CWM touch and then my touch screen stoped working so i tried to flash firmware and i got odin fail, from then when i turn it on it says "Firmware upgrade encountered an issue.Please select recovery mode in Kies & try again"..
Odin message:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P6810OZSLP8_P6810ZSLP8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
How can i fix this problem?
Cheers!!
bajki_ktm said:
Hello guys,
i have problem with my P6810 16gb Wifi tablet, the problem started when i flashed CWM touch and then my touch screen stoped working so i tried to flash firmware and i got odin fail, from then when i turn it on it says "Firmware upgrade encountered an issue.Please select recovery mode in Kies & try again"..
Odin message:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P6810OZSLP8_P6810ZSLP8_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Added!!
How can i fix this problem?
Cheers!!
Click to expand...
Click to collapse
If you have kies installed in your computer, please try to disable or uninstalled it. As I know, Samsung KIES and ODIN could not get along with together....
cakrabayu said:
If you have kies installed in your computer, please try to disable or uninstalled it. As I know, Samsung KIES and ODIN could not get along with together....
Click to expand...
Click to collapse
I don't have installed KIES..
Sorry....Did you follow this guide while using odin? http://forum.xda-developers.com/showthread.php?t=1469635 just wondering why you encounterred a problem. Thx.
Sent from my GT-P6800
cakrabayu said:
Sorry....Did you follow this guide while using odin? http://forum.xda-developers.com/showthread.php?t=1469635 just wondering why you encounterred a problem. Thx.
Sent from my GT-P6800
Click to expand...
Click to collapse
I was doing everything like in tutorial, tablet was full charged and i got this error, that's the story..
What could possibly go wrong?
bajki_ktm said:
I was doing everything like in tutorial, tablet was full charged and i got this error, that's the story..
What could possibly go wrong?
Click to expand...
Click to collapse
Really sad about your problem bro.... something wrong with the procedure or your firmware.. there are many cases like you.. you can refer to :
http://androidforums.com/samsung-ga...help-firmware-flashing-failed-using-odin.html
http://forum.xda-developers.com/showthread.php?t=1877308&page=2
http://forum.xda-developers.com/showthread.php?t=1984717
http://forums.whirlpool.net.au/archive/1919243
but it is up to you to give it a try. Luckily for me, I did not encounter the same problem like yours while flashing with pc odin. I prefer using mobile odin. it is safe and easy. Good luck bro...
I am having the same issue on my P6810 (16gb). I cannot use the emergency recovery in Kies because I don't have the recovery code that it asks for (I bought the device as used faulty so don't know the update history). When I try to use the firmware upgrade / initialisation function to reset the tablet, Kies downloads the firmware but fails to connect to the tablet when I plug it in (in download mode, which I can access).
I have tried flashing a downloaded firmware using Odin3 v1.85 and it appears to start okay and copies cache.img but quickly hangs at the factoryfs.img stage.
I have tried different both win7x64 and winXP PCs with no success. I did try Heimdall, which uses a different USB driver, and while I did not have an appropriate Heimdall compatible firmware to flash, I was able to get a display of the current PIT information, so the tablet was communicating OK.
Does my device need repartitioning? I have seen many references to a PIT file, but don't know where to download it from.
This seems to be a common problem from what I can tell so far.
Any help appreciated.
Thanks.
Hello i have the same problem. I read all of your suggestions and guess that should be use a pit-file. Is this overwrite a system. I have troubled ROM compiled and want to install the new one downloaded from sammobiles fo my country. Am I right? Please help me?
when I boot it just gives me some kernel is not seandroid enforcing so i'm trying to flash a stock firmware. G900P_SPR_G900PVPU3BOG1_G900PSPT3BOG1_Original.zip. is the name of file and its for a sprint S5.
Here is the odin output
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
HELP ME please.
I can flash the backup although it gets stuck at yellow boot screen. but that does get rid of the seaandroid enforcing
If someone could help me as well I'm having a similar problem. I have tried using multiple Odin versions and many stock SM-G900P 4.4.2 firmwares from multiple sources, but always have the same messages pop up.
Odin:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_SPT_G900PVPU1BOA6_G900PSPT1BOA6_CL3859396_QB3804569_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
USB debugging is on and Odin does recognize the device is connect, I have also already installed the drivers again just to be sure. I have used Odin before with no trouble maybe its the fact the phone is from sprint and on lollipop since sprint is stingy on unlocking -_-. If someone could point me in the right direction or 100% working firmware links I'd appreciate it. I have also tried going about this through Heimdall and failed not even being able to obtain the pit file. If someone could provide a working one I'd also appreciate it I am fully aware it may brick the phone as everything else may do. Or show me the me the step by step to flash with Heimdall with a .tar. I'll take any advice thank you
you can try the newer firmware ok4
maybe this will work . unzip and place md5 in ap slot of odin
http://forum.xda-developers.com/spr...t/rom-sprint-ok4-stock-tar-file-odin-t3262667
Sprint new locked bootloaders
unteaglejohnk said:
when I boot it just gives me some kernel is not seandroid enforcing so i'm trying to flash a stock firmware. G900P_SPR_G900PVPU3BOG1_G900PSPT3BOG1_Original.zip. is the name of file and its for a sprint S5.
Here is the odin output
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
HELP ME please.
Click to expand...
Click to collapse
I have the same problem myself and it took me a few minutes to realize what the problem is. I just got a new phone from Sprint because my other one the USB port was basically broken I couldn't connect or charge. So after a few failed attempts at flashing a ROM I decided to look at my firmware and realized that it was the new updated bog1 version. Sprint decided to lock all the boot loaders so as of this moment I don't know how to flash any ROM or downgrade as the bootloader will not let you. As a matter of fact just last night I was walking into Walmart I pulled my phone out of my pocket to look at it and it was just finishing up installing some security policy updates. My phone then immediately restarted and got stuck at the spark screen. Just the fact that I was rooted sent my phone into a boot loop. As of right now the only thing I can do is reflash the stock bog 1. I have managed to get access to this one and I'm working on modifying the bootloader in anyway I can. I'm a little newer to this but I catch on pretty quick. As of now I have all the permissions unlocked for me to access all the files in that stock bog1 rom but haven't found a way to make them stick yet. I'm going to have to break down each individual file and hopefully I can come up with a solution or anybody for that matter because I'm a few months away from my contract being up and if I can't root my phone and customize it I don't want it. If they want my phone lock down and toddler mode then they can pay for it that's how I look at it lol. Make sure you turn off automatic security updates. There's also a post in here of how to clean that out so you don't have the newest security policy update. I know the exact file the bootloader is in but haven't found a way to get into it or modify it yet even though I have permission. It shows it copying /deleting but doesnt change. There is way too many people in this world to not have someone come up with a solution by now and anytime I search for it I get results from a year to five years ago , hardly anything recent thanks google. I also posted on times and started a thread I'm trying but I'm not as advanced as some of these developers on here but I am determined lol
I finally got it to boot up. Just took like 20 mins. Now it boots sometimes while others it won't and says process has stopped responding after the yellow screen. Why does it do this. The rom is official rom directly off Samsung kids.
may have cracked bootloader BOG1 G900P
i have been playing in thr sys files and today i managed to get a custom animation boot installed. after that i flashed a modded bog1 file from philz. it took and succesfully booted and am now reinstalling all my apps. i think i over wrote or blocked my bootloader. ill get back when i know for sure:laugh:
http://samsung-updates.com/device/?id=SM-G900P
Hey guys, so my phone has been going in to boot loops. I would put it in recovery mode and clear the cache partition, that would get it to stop sometimes. Finally I did a factory reset. Now when its trying to set up my phone, it boot loops in the middle of that. So I used ODIN and tried to reinstall the firmware (OJ7), which was successful, but I'm back to boot loops during the phone set up process. Any ideas what to do next?
VanillaNasty said:
Hey guys, so my phone has been going in to boot loops. I would put it in recovery mode and clear the cache partition, that would get it to stop sometimes. Finally I did a factory reset. Now when its trying to set up my phone, it boot loops in the middle of that. So I used ODIN and tried to reinstall the firmware (OJ7), which was successful, but I'm back to boot loops during the phone set up process. Any ideas what to do next?
Click to expand...
Click to collapse
Have you did any modifications?
I installed an app on my phone that works in collaboration with a game. The app requires the phone to be rooted, but after researching the process to root a phone and the risk of voided Knox on 5.1.1 I decided against it and uninstalled the app. Its possible the app may have done something. But besides that there has not been any mods installed on my phone.
What causes the constant rebooting? Do I possibly have corrupted files that can be replaced with the recovery system? Any ideas would be helpful.
Is your bootloader unlocked?
Soooperstar said:
Is your bootloader unlocked?
Click to expand...
Click to collapse
I am not sure. Can I check that from the recovery mode or download mode screen?
VanillaNasty said:
I am not sure. Can I check that from the recovery mode or download mode screen?
Click to expand...
Click to collapse
Don't think so. Have you tried to Odin Ol1?
Soooperstar said:
Don't think so. Have you tried to Odin Ol1?
Click to expand...
Click to collapse
Just got that on the Ol1 ODIN attempt.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU3BOI1_G925PSPT3BOI1_G925PVPU3BOI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Edit: Since that failed, my phone will now only go into download mode. It says "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software." But Smart Switch is now saying I don't have an supported device.
VanillaNasty said:
Just got that on the Ol1 ODIN attempt.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU3BOI1_G925PSPT3BOI1_G925PVPU3BOI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Edit: Since that failed, my phone will now only go into download mode. It says "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software." But Smart Switch is now saying I don't have an supported device.
Click to expand...
Click to collapse
Can you Odin previous firmware?
Soooperstar said:
Can you Odin previous firmware?
Click to expand...
Click to collapse
Soooperstar, I appreciate you taking the time to try to help me. I took the phone to the Samsung vendor. She worked on it for 2 hours and couldn't get it to stop going into boot loops. Its being shipped to Samsung now so they can fix it.
Thanks again.
Hello all,
My tablet note 10.1 N8000 (3G, Wi-Fi, 16 GB) suddenly got stuck in bootloop. I was not trying to flash anything when it did so, nor did I flashed anything recently before the bootloop (although it seemed to constantly freeze before the bootloop when trying to switch between my two whatsapp accounts that I have using Titanium Backup which allows creating more than one account in all apps).
I did however root the device when I bought it in 2012 and it was the only time I did so, and I still have USB debugging mode on.
The device would bootloop in the first Samsung logo most of the time, but on rare occasions it would move to the second animated logo and get stuck repeating the animation forever.
I can only access Odin Download mode, but cannot access recovery mode (when I try to do so, it shows the first Samsung logo, then attempts to go into recovery but only shows a lit black screen then reboots).
Here are the steps I did (might help some of you, but unfortunately didn't help me):
1) I tried flashing a custom recovery (CMW, Philz touch, TWRP, and stock recovery) through Odin (Odin 3 version v3.10.6):
- Put the .tar file in AP slot then put device in download mode (power key + volume down), then plug device into my computer.
- Check only auto restart and F. time reset.
- Here's what it says after flashing:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
2) I tried flashing stock rom through Odin:
(Roms I tried: N8000XXCMF1, N8000XXUDOF1, N8000XWALG7, N8000XXCMA2, N8000XXUDOF1)
- I put the .tar.md5 file in AP and follow same steps above, here's what Odin says after flashing:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> tz.img
<ID:0/003> NAND Write Start!!
<ID:0/003> sboot.bin
<ID:0/003> system.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
3) I tried following the post here:
http://forum.xda-developers.com/galaxy-note-10-1/general/n8000-stuck-samsung-logo-t3212923
I followed everything until the part where I have to access recovery (because I could not access recovery still to flash rom from recovery). Here's what it says in Odin after it's done:
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9300_Repair_efs.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> efs.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
But again it did not work even though it always says "PASS"! And I also tried flashing stock rom after trying this method through Odin, shows success but still stuck in bootloop.
I don't know what else to try really. I will not take it to support to fix it, either I fix it myself or use it as a cutting board.
If anyone has any ideas please reply. I'm sure there are more things to try.
EDIT:
- Is there a way to clear cache without accessing recovery (since I can't access it)? Lots of people say it worked after clearing cache.
- Is Nand erase all an option? I wish someone would explain it in details instead of telling me not to do it without saying exactly why.
- Could the problem be in hardware? How can I know if so?
NaND ERASE WILL KILL THE PRODUCT .
JJEgan said:
NaND ERASE WILL KILL THE PRODUCT .
Click to expand...
Click to collapse
So you mean that it will erase everything even the Odin download mode and the Samsung logo? Why would they include this option then? I don't see any practical use of it :/
No help?
RHAddict said:
So you mean that it will erase everything even the Odin download mode and the Samsung logo? Why would they include this option then? I don't see any practical use of it :/
Click to expand...
Click to collapse
Odin is a tool that we are able to borrow .
You could try recovery via KIES .
RHAddict said:
No help?
Click to expand...
Click to collapse
HI RHAddict,
It happened to my Note GT-N8000, if a Hardware failure. If you send to SAMSUNG service center it will cost u around US$ 200 for motherboard replacement. But i manage to find a mobile service center, the technician said it only 1 of the chip in motherboard out of service. I got my tablet fixed just US$ 50-60. Now is working as is it before.
TQ
My Samsung 8010 has just gone exactly the same way. Cannot enter recovery mode, just get a blank lit screen for a second then goes back into a reboot cycle and never gets past the Samsung logo. Did you get anywhere with fixing it, or have you given up? Was thinking of taking mine to a service centre, but probably not worth it?
So i recently flashed lineage 14.1 j7ltespr to my J700p, and the rom loaded up fine, but it won't recognize the sim card. As this is my daily driver that can't be the case, so i tried to flash a stock rom back on. I think i could get it to work, but the phone won't boot into bootloader anymore.
It has the most recent version of twrp for the model. And it will system boot, and boot recovery just fine. But when i try to boot loader, it just gives me a charging symbol, and freezes. I've been trying to fix this anyway i can for the last 12 hours.
I also tried adb, and odin. Odin gives me an auth error every time i try to load a stock rom. If anyone could help, i'd be very appreciative.
I'd take fixing the sim not found, the bootloader not coming up, or the NAND Write Start!! FAIL! (Auth) error
thank you for your time
J700P
tjjc4 said:
So i recently flashed lineage 14.1 j7ltespr to my J700p, and the rom loaded up fine, but it won't recognize the sim card. As this is my daily driver that can't be the case, so i tried to flash a stock rom back on. I think i could get it to work, but the phone won't boot into bootloader anymore.
It has the most recent version of twrp for the model. And it will system boot, and boot recovery just fine. But when i try to boot loader, it just gives me a charging symbol, and freezes. I've been trying to fix this anyway i can for the last 12 hours.
I also tried adb, and odin. Odin gives me an auth error every time i try to load a stock rom. If anyone could help, i'd be very appreciative.
I'd take fixing the sim not found, the bootloader not coming up, or the NAND Write Start!! FAIL! (Auth) error
thank you for your time
Click to expand...
Click to collapse
Can you go into settings an turn off adb root then you should be able to flash stock from Odin ! Use Odin 3.12.5 !!
peter couniaz said:
Can you go into settings an turn off adb root then you should be able to flash stock from Odin ! Use Odin 3.12.5 !!
Click to expand...
Click to collapse
Thank you peter for the advice. I tried what you suggested. Still no luck. Here is the output of the odin runs, they were all identical though i tried different roms, 3 different versions of odin, root on and off, as well as with debugging on and off. Same out put every time.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2970 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the output on the download screen on the phone throws this error
SW REV CHECK FAIL : [aboot] Fused 2 > Binary 1
I hope that helps.
J700P
tjjc4 said:
Thank you peter for the advice. I tried what you suggested. Still no luck. Here is the output of the odin runs, they were all identical though i tried different roms, 3 different versions of odin, root on and off, as well as with debugging on and off. Same out put every time.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2970 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the output on the download screen on the phone throws this error
SW REV CHECK FAIL : [aboot] Fused 2 > Binary 1
I hope that helps.
Click to expand...
Click to collapse
It all or nothing on this if you can get into recovery factory reset then wipe system an go into download mod an try Odin one last time ! But before all that make shore debugging is on an make shore you are using a Samsung usb cord best the one that came with the phone ! An use Odin 3.12.5 or older 3.13.01 doesn't work right for that phone !!! PS make the firmware file isn't mest up ! Get the latest firmware file !