ok so my Samsung galaxy s6 is stuck in download mode i tried to do a clean flash to install a rom but it failed and now i can only go to download mode its dose not boot up or anything i tried flashing twrp through odin did not work i tried flashing stock firmware didn't work smart switch and kies3 dont recognize my device the device is a sm-G920T when i tried flashin the frimware i get sw rev check fail device 5 binary 2 pls help
Related
I tried to flash my samsung i8160P with i8160XXLK7 firmware using odin.All threads were completed(succeed 1 / failed 0).But my phone cant start(not booting) and cant get detected by pc.Any help
I tried to flash my device with flashify, and after I did, It rebot and now It's stuck at the boot logo I can only put my phone on Download mode, the power up recovery settings doesn't not work at all, I tried flashing it back to firmware but I will get "CHECK FAIL DEVICE: 3 BINARY: 2" any help I downloaded the right firmware, my device that I got is, Samsung s6 edge (SM-G925P) any help !
Flash the right kernel! I had the same issue!
I had the same problem. Just flash recovery firmware for your device using Samsung Smart Switch. Works perfectly.
delete
AutoRemixSound said:
I tried to flash my device with flashify, and after I did, It rebot and now It's stuck at the boot logo I can only put my phone on Download mode, the power up recovery settings doesn't not work at all, I tried flashing it back to firmware but I will get "CHECK FAIL DEVICE: 3 BINARY: 2" any help I downloaded the right firmware, my device that I got is, Samsung s6 edge (SM-G925P) any help !
Click to expand...
Click to collapse
Install Smart Switch (Kies for newer models) on a computer, and use the option Emergency software recovery and initialization.
Hello,
My N8000 was updating today and it got stuck at the samsung logo agter the "Galaxy note 10.1" screen. I am unable to access recovery mode; only download mode. I have been looking for hours for a solution but can't find any. I have tried to flash a stock ROM from sammobile not working (odin always fails) , tried flashing both custom and stock recoveries but odin keeps failing. I installed the toolkit but inorder to flash roms and stuff i need usb debugging to be enabled, and it is not. Is there a way to enable it while on bootloop?
Thanks,
Where does Odin fail ??
JJEgan said:
Where does Odin fail ??
Click to expand...
Click to collapse
When flashing stock recovery, it fails at recovery.img, flashing rom at boot.img
Suggests wrong files used .
Or possible damaged NAND .
Hi
I tried to flash stock firmware via odin by mistakenly selected NAND erase option and odin failed
After that it's not booting to download mode (odin mode).
Can someone help me to unbrick my phone.
So I have an old SM-G920W8 that was with Rogers, but when I turned it on it would get stuck on the galaxy s6 screen. So I tried entering the recovery thing or whatever it was called but there was text at the top left that said "recovery is not seandroid enforcing", so then I tried to flash the stock firmware back on with Odin 3.10.6 with the ROM I got from Frija, but it fails every time.
ToadNugget said:
So I have an old SM-G920W8 that was with Rogers, but when I turned it on it would get stuck on the galaxy s6 screen. So I tried entering the recovery thing or whatever it was called but there was text at the top left that said "recovery is not seandroid enforcing", so then I tried to flash the stock firmware back on with Odin 3.10.6 with the ROM I got from Frija, but it fails every time.
Click to expand...
Click to collapse
Hmm ... Should work.
Have you downloaded the correct firmware?
Best to check the installation guide again and repeat it:
Samsung Galaxy S6 SM-G920W8 Stock Firmware (ROM Flash File) [DOWNLOAD]
Download the official Samsung Galaxy S6 SM-G920W8 Stock Firmware ROM (Flash File) for your Samsung Smartphone and unbrick the device, fix boot loop and more.
firmwarepanda.com
Keep in mind that flashing a different CSC with Odin needs doing a factory reset with doing data.
That is why I always prefer using "Home_CSC" to keep my CSC and data.
It_ler said:
Hmm ... Should work.
Have you downloaded the correct firmware?
Best to check the installation guide again and repeat it:
Samsung Galaxy S6 SM-G920W8 Stock Firmware (ROM Flash File) [DOWNLOAD]
Download the official Samsung Galaxy S6 SM-G920W8 Stock Firmware ROM (Flash File) for your Samsung Smartphone and unbrick the device, fix boot loop and more.
firmwarepanda.com
Keep in mind that flashing a different CSC with Odin needs doing a factory reset with doing data.
That is why I always prefer using "Home_CSC" to keep my CSC and data.
Click to expand...
Click to collapse
OK I tried that, but then it said "SW REV. CHECK FAIL. DEVICE: 5, BINARY: 3" and now the screen wont turn on
ToadNugget said:
OK I tried that, but then it said "SW REV. CHECK FAIL. DEVICE: 5, BINARY: 3" and now the screen wont turn on
Click to expand...
Click to collapse
Check this thread:
Sw rev. Check fail. Device: 5, binary 3
Hi, I've got a Galaxy S6 G920F on Vodafone that I am trying to downgrade from 7.0 to 6 or 5 so that I can go through with an unlocking procedure but I keep getting the error message " SW REV. CHECK FAIL. DEVICE: 5, BINARY 3". Can anyone help?
forum.xda-developers.com
Seems that you have to flash another firmware version.
Hi Guys,
Device: Samsung Galaxy Note N7000
Power On: Stuck with popup "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again"
Stock ROM: can't locate firmware for those BL, AP, CP, CSC files
Anyone can help? Appreciated.
Cheers