I have an old 8013 Note 10.1 that I let my kids use, it's had CM on it forever and no issues until recently. Now it boots up to the CM bootscreen but doesn't go any further. I've booted to TWRP and tried to format and install a new ROM but it doesn't seem to even format. When I go to load a new ROM it always shows that the internal storage is the same free space (something like 513Mb). I've tried flashing PhilzTouch, TWRP, CWM, and when I reboot to recover it's still the same version of TWRP I started with. Tried flashing a stock ROM, still boots to the CM Logo. Loaded ODIN on my computer and tried flashing a stock image using ODIN and it shows it's successful, but nothing changes on the tablet. I even tried the instructions listed in this post, which should reformat everything and still - same issue.
I've attached a few screenshots of the kinds of errors and messages I get in TWRP when I try to format, do an advanced wipe of everything and still a new ROM. Any suggestions would be great! I'm ready to give up on this thing, but I still have a sliver of hope.
Re install your oriGinal frimware
Sent from my SM-J700F using Tapatalk
saismarty said:
Re install your oriGinal frimware
Sent from my SM-J700F using Tapatalk
Click to expand...
Click to collapse
As I think I mentioned, I've tried. Just to be clear I've added some screenshots and output from ODIN.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_N8013UEUCOI1_N8013XARCOI1_813049_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> sboot.bin
<ID:0/003> param.bin
<ID:0/003> tz.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Looks like everything is flashing just fine... until I reboot the tablet and get the CM Boot logo again and the tablet just gets stuck there...
What happened next
Sent from my SM-J700F using Tapatalk
saismarty said:
What happened next
Sent from my SM-J700F using Tapatalk
Click to expand...
Click to collapse
Cyanogenmod boot animation and just stuck there... just like ODIN never happened.
Try doing Odin but check Nand erase all, if you know what that does it should wipe what's holding your tablet back and then flash stock firmware, just hope it works, I don't know anything else really
Related
My Galaxy note 10.1 bricked itself all I did was downloading cyanogenmod at night and when I wake up It was bricked.
When I go to Recovery it says 'e: cant open /cache/recovery/log' when I try to install zip from sdcard it says
"E: cant mount sdcard and restarts itself . I spent almost all day here at xda but couldnt fix.
:crying::crying::crying::crying:
Please Help I tried flashing a new recovery ( TWRP over CWM) but didn't work it went back to cwm .
I have no external SD card.
Why no try flash a stock rom?
mrlucaszarate said:
Why no try flash a stock rom?
Click to expand...
Click to collapse
I don't know what the problem is I flashed the stock rom using odin and without interuption it flashed but still in bootloop
when i went to recovery CWM was not removed . CWM gives errors like e: cant open ......... and e: cant mount sdcard and all that .
What should I do??
I Installed stock ROM using different versions of odin but also cwm is not removed and im still in bootloop .
Any idea what is happening here . I think cwm has to do something with the bootloop :crying:
ODIN LOG
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1100)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Do You try wipe data and data cache after flashing?
Hey guys, so my phone has been going in to boot loops. I would put it in recovery mode and clear the cache partition, that would get it to stop sometimes. Finally I did a factory reset. Now when its trying to set up my phone, it boot loops in the middle of that. So I used ODIN and tried to reinstall the firmware (OJ7), which was successful, but I'm back to boot loops during the phone set up process. Any ideas what to do next?
VanillaNasty said:
Hey guys, so my phone has been going in to boot loops. I would put it in recovery mode and clear the cache partition, that would get it to stop sometimes. Finally I did a factory reset. Now when its trying to set up my phone, it boot loops in the middle of that. So I used ODIN and tried to reinstall the firmware (OJ7), which was successful, but I'm back to boot loops during the phone set up process. Any ideas what to do next?
Click to expand...
Click to collapse
Have you did any modifications?
I installed an app on my phone that works in collaboration with a game. The app requires the phone to be rooted, but after researching the process to root a phone and the risk of voided Knox on 5.1.1 I decided against it and uninstalled the app. Its possible the app may have done something. But besides that there has not been any mods installed on my phone.
What causes the constant rebooting? Do I possibly have corrupted files that can be replaced with the recovery system? Any ideas would be helpful.
Is your bootloader unlocked?
Soooperstar said:
Is your bootloader unlocked?
Click to expand...
Click to collapse
I am not sure. Can I check that from the recovery mode or download mode screen?
VanillaNasty said:
I am not sure. Can I check that from the recovery mode or download mode screen?
Click to expand...
Click to collapse
Don't think so. Have you tried to Odin Ol1?
Soooperstar said:
Don't think so. Have you tried to Odin Ol1?
Click to expand...
Click to collapse
Just got that on the Ol1 ODIN attempt.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU3BOI1_G925PSPT3BOI1_G925PVPU3BOI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Edit: Since that failed, my phone will now only go into download mode. It says "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software." But Smart Switch is now saying I don't have an supported device.
VanillaNasty said:
Just got that on the Ol1 ODIN attempt.
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925PVPU3BOI1_G925PSPT3BOI1_G925PVPU3BOI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cm.bin
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Edit: Since that failed, my phone will now only go into download mode. It says "An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software." But Smart Switch is now saying I don't have an supported device.
Click to expand...
Click to collapse
Can you Odin previous firmware?
Soooperstar said:
Can you Odin previous firmware?
Click to expand...
Click to collapse
Soooperstar, I appreciate you taking the time to try to help me. I took the phone to the Samsung vendor. She worked on it for 2 hours and couldn't get it to stop going into boot loops. Its being shipped to Samsung now so they can fix it.
Thanks again.
So, i wanted to flash the griffin rom. Had the tyrannus rom installed before and started with flashing the bootloader and modem.
After it finished the phone restarted and booted up automatically. After a few hours ( i was at work) i finally wanted to flash the rom. When i got in recovery mode, twrp asked something about partitions and make changes or something ( never read it before) i agreed. after the phone rebooted it got stuck at the boot screen. ( The s6 logo). Even when i wanted to boot into recovery mode the "recovery is not seandroid enforcing" was staying there for ever. i couldnt get into recovery. So i wanted to flash the stock rom via odin. but in odin if i want to flash the stock rom or a bootloader, then odin fails with the message:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> cache.img
<ID:0/003> cm.bin
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm really lost. I would be glad if somebody could help me :/
You probably have a newer Bootloader than the Stock ROM you are trying to flash.
Flash a newer Stock ROM, that would match your bootloader version.
Samsung Galaxy s6 (SM-G920F) stuck in boot loop. cant reset this damn phone tried Odin nothing works. Btw there is nothing to be saved on the phone i just Want it to boot so i Can use it again... Anyone Got anything?
story: i rooted my phone perfectly. Factory reset it cuz i wanted to start from new. Then it happend, boot loop. I have tried downloadning The firmware dosent work. Vol up, down, home n power in what order i dont remember and factory reset dosent work either.
Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 3547 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
looooong waiting time.....
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
dude you're just saying a bunch of random stuff... explain in more detail...
that said however...
i was once stuck in bootloop. what i did was:
put my phone in download mode
downloaded and flashed the latest TWRP for my phone
downloaded a custom rom
booted to TWRP
using twrp, i wiped system, data, both cache
then i flashed the custom rom using TWRP
waited for the "first boot will take some time" boot up
problem solved...
now you try it...
Spin_Master said:
dude you're just saying a bunch of random stuff... explain in more detail...
that said however...
i was once stuck in bootloop. what i did was:
put my phone in download mode
downloaded and flashed the latest TWRP for my phone
downloaded a custom rom
booted to TWRP
using twrp, i wiped system, data, both cache
then i flashed the custom rom using TWRP
waited for the "first boot will take some time" boot up
problem solved...
now you try it...
Click to expand...
Click to collapse
Yeah i did that but with Odin i get that, so i cant get any further in proces.
Sorry im new to Android...
So i recently flashed lineage 14.1 j7ltespr to my J700p, and the rom loaded up fine, but it won't recognize the sim card. As this is my daily driver that can't be the case, so i tried to flash a stock rom back on. I think i could get it to work, but the phone won't boot into bootloader anymore.
It has the most recent version of twrp for the model. And it will system boot, and boot recovery just fine. But when i try to boot loader, it just gives me a charging symbol, and freezes. I've been trying to fix this anyway i can for the last 12 hours.
I also tried adb, and odin. Odin gives me an auth error every time i try to load a stock rom. If anyone could help, i'd be very appreciative.
I'd take fixing the sim not found, the bootloader not coming up, or the NAND Write Start!! FAIL! (Auth) error
thank you for your time
J700P
tjjc4 said:
So i recently flashed lineage 14.1 j7ltespr to my J700p, and the rom loaded up fine, but it won't recognize the sim card. As this is my daily driver that can't be the case, so i tried to flash a stock rom back on. I think i could get it to work, but the phone won't boot into bootloader anymore.
It has the most recent version of twrp for the model. And it will system boot, and boot recovery just fine. But when i try to boot loader, it just gives me a charging symbol, and freezes. I've been trying to fix this anyway i can for the last 12 hours.
I also tried adb, and odin. Odin gives me an auth error every time i try to load a stock rom. If anyone could help, i'd be very appreciative.
I'd take fixing the sim not found, the bootloader not coming up, or the NAND Write Start!! FAIL! (Auth) error
thank you for your time
Click to expand...
Click to collapse
Can you go into settings an turn off adb root then you should be able to flash stock from Odin ! Use Odin 3.12.5 !!
peter couniaz said:
Can you go into settings an turn off adb root then you should be able to flash stock from Odin ! Use Odin 3.12.5 !!
Click to expand...
Click to collapse
Thank you peter for the advice. I tried what you suggested. Still no luck. Here is the output of the odin runs, they were all identical though i tried different roms, 3 different versions of odin, root on and off, as well as with debugging on and off. Same out put every time.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2970 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the output on the download screen on the phone throws this error
SW REV CHECK FAIL : [aboot] Fused 2 > Binary 1
I hope that helps.
J700P
tjjc4 said:
Thank you peter for the advice. I tried what you suggested. Still no luck. Here is the output of the odin runs, they were all identical though i tried different roms, 3 different versions of odin, root on and off, as well as with debugging on and off. Same out put every time.
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1301)..
<ID:0/003> File analysis..
<ID:0/003> Total Binary size: 2970 M
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> NAND Write Start!!
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Also the output on the download screen on the phone throws this error
SW REV CHECK FAIL : [aboot] Fused 2 > Binary 1
I hope that helps.
Click to expand...
Click to collapse
It all or nothing on this if you can get into recovery factory reset then wipe system an go into download mod an try Odin one last time ! But before all that make shore debugging is on an make shore you are using a Samsung usb cord best the one that came with the phone ! An use Odin 3.12.5 or older 3.13.01 doesn't work right for that phone !!! PS make the firmware file isn't mest up ! Get the latest firmware file !