This TWRP is for NAVON Raptor 3G
It isn't compatible with NAVON Raptor 7, and never will!
Requirements:
Code:
[COLOR="Red"][B]-Unlocked bootloader[/B][/COLOR]
-ADB files
-Mediatek drivers (ADB driver, VCOM driver, etc..)
You can also try to flash this recovery with Flashify + root but it's not tested!
The following only applies to locked tablets:
To unlock bootloader go to Settings>About tablet and tap the Build number 3 times
Go to Developer settings, and tap on OEM unlocking
In CMD type adb reboot bootloader, this will reboot the tablet into fastboot mode
Place the recovery.img into the root folder of adb (i.e.: C:\adb\recovery.img)
Then type the following and enter per line:
Code:
[I][B]cd c:\adb[/B][/I]
[I][B]fastboot flash recovery recovery.img[/B][/I]
If you get a permission not allowed, your tablet isn't unlocked, you need to unlock it.
Warning: Unlocking bootloader will wipe your data!
Type: fastboot oem unlock
Then press Volume Up, it should say success. If it's not, repeat the oem unlock steps and try again.
Reset the tablet, then power up the Tablet by pressing Power + Volume up, then select Recovery
Enjoy the recovery!
What's not working:
Code:
-Mount USB storage
-MTP
-You tell me
Download link: https://drive.google.com/open?id=0B9kEI7tbfDrbU1NiVENCcFF6VGM
For Hungarians:
Ha bootloopol a tablet, nézd meg hogy unlockolva van-e az OEM unlock
a Build-ra koppintva 3x behozza a fejlesztői beállításokat, majd az OEM Unlock-ra kell menni
A tablet már nincs meg nekem, így nem tudok segíteni
Related
Hi there!!
Well I was trying to root this phone since a month but due to lack of developers, it wasn't possible. So I tried and at last succeeded in rooting and porting TWRP recovery for Intex Aqua Music.
I tried to elaborate every step as much as I can so the tutorial becomes user friendly for everyone.
Disclaimer: Rooting immediately voids your phone's warranty, you should consider very carefully whether you need to gain root privileges. And this tutorial will format your phone. So backup you important files at the very first.
Tutorial
First download all the files which i left and the end of the thread and proceed with the tutorial.
First of all you need to install ADB Drivers.
Once drivers are installed, you need to enable USB Debugging in your phone.
(goto phone settings->About phone->scroll down and you’ll see an entry labelled ‘Build number.’ Keep on tapping till you see a prompt that says ‘You are now a developer)
Now in phone settings you will see a new option called Developer Options.
Now goto Developer Options and enable OEM Unlocking(for unlocking the bootloader so you can flash the TWRP recovery) and USB Debugging.
Now connect you phone with usb cable to computer and open the adb and fastboot folder which you downloaded.
Then open command prompt there(shift+right click) and type:
Code:
adb devices
You will see a popup on you phone screen, Select allow and ok
Now you will see your device listed there in command prompt.
Now type the following commands:
Code:
adb reboot bootloader
Phone will switch off and go into bootloader. Then type
Code:
fastboot oem unlock
Now you phone will ask for confirmation. Use Volume UP Button to select yes then type
Code:
fastboot continue
.
Now your device will reboot(it will take some time so don't worry)
Now once your phone boot up you will see its formatted and bootloader will be unlocked.
Now again goto setting and enable USB Debugging like before and connect you phone with pc.
Now copy the recovery.img from recovery zip which you downloaded to adb and fastboot folder.
Then in adb command prompt type the following commands like before
Code:
adb reboot bootloader
Wait for the phone to go into bootloader mode, then
Code:
fastboot flash recovery recovery.img
fastboot continue
Now twrp is flashed in your phone. Now to root your device copy the supersu zip to you phone.
Switch off your mobile, then press Volume Up + Power button together then choose recovery mode with Volume UP Button and
press Volume Down Button.
Now phone will boot into TWRP recovery mode.
Click Install and choose the Super Su zip from file manager then install it.
The click reboot and once your phone boots up its rooted now.
Enjoy!
Thanks button will be appreciated if the tutorial works for you.
Thanks
Thanks man, helpful
Hi Everyone
I will show you how to unlock bootloader, install TWRP and ROOT on
ASUS Zenfone 3 Max 5.5 ZC553KL (X00D).
Before you remember to backup data carefully.
All needed files will be in this folder:
Please edit all the link to be form of google shorterner
goo. gl/xCAUAB
1. We downloaded two driver compression files on:
Adb: goo. gl/SBVPVG
Intel Android Driver: goo. gl/oYN7mG
2.Download this file:
goo. gl/5yA6yp
3. After you download all the necessary files, you unzip them all and start installing.
Run file adb-setup-1.4.2.exe to setup adb
Adb is now installed Intel Android Driver next next time as usual.
That is the driver. Now copy the two files (frp.BIN and twrp-3.1.1-0-X00D-20171020-5.img) into the C: \ adb folder.
4. Brother downloaded this file supersu and then copy to phone memory card.
goo. gl/jLmknM
5. Now start using adb to flashboot
After copying, we go to PowerShell (Admin) if using windows 10
You guys use win7 and 8 then run cmd with admin rights.
After open brother type the following commands in turn order:
cd C: \ adbadb reboot bootloader
The command to enter the bootloader, wait for the machine and then reset then type.
fastboot flash config frp.bin
Waitt for the copy to complete the command to reset.
fastboot reboot-bootloader
After resetting, type the following command:
fastboot oem unlock-go
Once done, type in the following command:
fastboot reboot
After the reboot finishes the power off.
Then press the volume key + before pressing the power button, wait for the screen, then release the power button to keep the volume + key to bootloader.
Please enter the order fastboot flash recovery
twrp-3.1.1-0-X00D-20171020-5.img
Wait for the file to finish typing the command below to enter the TWRP
fastboot oem reboot-recovery
After entering the TWRP, the brothers swipe the left "Swipe modified system".
Next select Install -> Select Storage under -> Micro SDCard -> OK
Youu will see the file SuperSU-V2.82.zip you just copied to the memory card.
Click on this file -> Swipe to Right Swipe to confirm Flash Finished, now sit back to finish running and reset the machine.
So is root finished.
Wishing you success.
LOL? You made this method yourself? I saw this in somewhere on this forum.
https://forum.xda-developers.com/zenfone-3/how-to/zenfone-3-max-zc553kl-bootloader-unlock-t3691837
After installing twrp recovery. Will my phone resets its phone data?
hello, i try to unlock bootloader and in adb when i type: fastboot flash config frp.bin it say error: cannot load 'frp.bin' : no such file or directory but 'frp.bin is in the same folder of adb i don't understand why it do this error i'm in fastboot mode i tryed de reboot my pc but it do the same error can you help me please thanks a lot!!
Does this method work on zenfone 3 max zc553kl with android 7.1.1? Thank you
is this tut is working for 7.1.1 version?
Revert to stock
How i can remove TWRP e revert to stock recovery ?
ZC553KL
hello its been a while is it available for Android 8.1?
Hello, I could not download the files. Could you please submit a new link? Thank you very much in advance.
How to unlock bootloader & get root for Lenovo K8 Plus
**********Pre-requirements***********
1. Make sure you have 70% charge or more then that.
2. Follow all steps correctly otherwise you will end up with a bricked phone.
3. I'm not responsible for any damage to your phone.
4. Make sure that you have installed usb drivers.
5. Download ADB & Fastboot Drivers
Steps to Unlock Bootloader
1. First of all, enable the Developer Option
To Enable the Developer Option, Go to your Settings -> About -> Software Information -> More -> Now Tap on the Build Number 7-8 Times until you see a toast message “Developer option enabled"
2. Go back to settings -> Now you need to enable the OEM Unlock by going to Settings -> Developer Option and Enable OEM Unlock and USB Debugging
3. Download and Extract the Downloaded ADB fastboot Zip file on your phone.
4. Now connect your phone to Computer using USB Cable.
When you connect your Phone to Computer, please wait until all the drivers get installed.
5. In your ADB fastboot folder open a command prompt window by pressing Shift Key + Right Mouse Click
Now type the command in your command window
Code:
adb devices
6. If you see a pop up to allow USB Debugging on your phone, Click OK
Now type the command below to reboot your phone to bootloader
Code:
adb reboot bootloader
7. Once your phone reboot into bootloader, make sure your phone shows the bootloader locked and then type the command below to make sure fastboot drivers are installed properly.
Code:
fastboot devices
8. This command will list the connected devices. If your phones serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly. In order for you to continue, you must fix your drivers so that your phone is listed under fastboot devices.
9. If the phone has been recognized by the command above, proceed to unlock the bootloader with the following command:
Code:
Remember that this step will wipe EVERYTHING off the phone
Code:
fastboot oem unlock
10. After the above command has finished executing, run the following
Code:
fastboot reboot
The phone will reboot. Wait until the phone has fully booted up into Android.
Root method
Note:- All credits for it goes to @topjohnwu for his amazing magisk
Requirements:-
1. Make sure you are on latest September patch firmware.
2. Download patched_boot.img created from magisk mangaer.
Instructions:-
1. Connect up your phone then type:-
Code:
adb reboot bootloader
2. Copy patched_boot.img in adb folder.
Now type
Code:
fastboot flash boot patched_boot.img[/url]
3. Open up you device & install magisk manager from [url=https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445]here[/url]
Voilla you're rooted.
Mod Edit
Duplicate thread is closed
malybru
Senior Moderator
How to unlock bootloader & get root for Lenovo K8 Plus
**********Pre-requirements***********
1. Make sure you have 70% charge or more then that.
2. Follow all steps correctly otherwise you will end up with a bricked phone.
3. I'm not responsible for any damage to your phone.
4. Make sure that you have installed usb drivers.
5. Download ADB & Fastboot Drivers
Steps to Unlock Bootloader
1. First of all, enable the Developer Option
To Enable the Developer Option, Go to your Settings -> About -> Software Information -> More -> Now Tap on the Build Number 7-8 Times until you see a toast message “Developer option enabled"
2. Go back to settings -> Now you need to enable the OEM Unlock by going to Settings -> Developer Option and Enable OEM Unlock and USB Debugging
3. Download and Extract the Downloaded ADB fastboot Zip file on your phone.
4. Now connect your phone to Computer using USB Cable.
When you connect your Phone to Computer, please wait until all the drivers get installed.
5. In your ADB fastboot folder open a command prompt window by pressing Shift Key + Right Mouse Click
Now type the command in your command window
Code:
adb devices
6. If you see a pop up to allow USB Debugging on your phone, Click OK
Now type the command below to reboot your phone to bootloader
Code:
adb reboot bootloader
7. Once your phone reboot into bootloader, make sure your phone shows the bootloader locked and then type the command below to make sure fastboot drivers are installed properly.
Code:
fastboot devices
8. This command will list the connected devices. If your phones serial number shows up you are good to go and may continue. If the phone is NOT listed this indicates that your drivers are not installed correctly. In order for you to continue, you must fix your drivers so that your phone is listed under fastboot devices.
9. If the phone has been recognized by the command above, proceed to unlock the bootloader with the following command:
Code:
Remember that this step will wipe EVERYTHING off the phone
Code:
fastboot oem unlock
10. After the above command has finished executing, run the following
Code:
fastboot reboot
The phone will reboot. Wait until the phone has fully booted up into Android.
Root method
Note:- All credits for it goes to @topjohnwu for his amazing magisk
Requirements:-
1. Make sure you are on latest September patch firmware.
2. Download patched_boot.img created from magisk mangaer.
Instructions:-
1. Connect up your phone then type:-
Code:
adb reboot bootloader
2. Copy patched_boot.img in adb folder.
Now type
Code:
fastboot flash boot patched_boot.img[/url]
3. Open up you device & install magisk manager from [url=https://forum.xda-developers.com/apps/magisk/official-magisk-v7-universal-systemless-t3473445]here[/url]
Voilla you're rooted.
twrp please for lenovo k8 +++++
Mod Edit
Duplicate thread is closed
malybru
Senior Moderator
I don't like the Test Point method, so You need: Twrp - this edition works: https://drive.google.com/drive/folders/1FoRLBMyQnL1B3lU8bZCqfGL7y_mkeJfk. You need to use HCU, part of the DC Unlocker software. The Magisk.zip needs to be placed in the tablet's folder on the SD card preferably. The tablet must be set to 'transfering files' and the Background Settings, USB port setting, obtained by using the dialler * # * # 2846579 # * # * or the calculator (I believe) for the WiFi version, to Manufacture Mode. So, with the tablet in the operational mode, not Fastboot or anything else, plug it in to the PC. Buy the time-limited mode for HCU and then log in to it. Press read phone info, give it a minute or so then press unlock, after the info states that it detects the phone. The Bootloader should be unlocked, not as in the Developer Mode/OEM Unlocked with USB Debugging selected, which are also necessary. Once you have unlocked with HCU, boot into Fastboot - vol down + power buttons. You should have the minimal ADB folder on the C: drive. Place the TWRP8.img in that folder.Navigate to the ADB folder in your command prompt, something like: CD\ then CD ADB. You should now be in the ADB folder. Type: fastboot flash recovery_ramdisk twrp8.img NOT fastboot flash recovery twrp8.img. Do a reset of the phone in Recovery Mode and it should then boot in TWRP. Flash the Magisk.zip with TWRP. Restart the tablet. You may have reset the tablet in Recovery Mode again to get the TWRP recovery working. You should now have root with Magisk after the tablet re-boots. I did not flash Disable DM Verity. (Earlier, I tried using Magisk to convert the ramdisk.img from the Update.App to gain root. I flashed it with Fastboot but it did not work, it ended in a boot-loop which I could not stop by any means.)