Hi you all, I have a non common bluetooth problem. My S6 is running Xtrestolite with android 6.0. My phone can connect BT to my cars, my earset and my soundbar to play music and it work well even on my earset. BUT, nothing for voice call, the call connect and silence for everyone. There is no voice at all, but BT is connected, and all infos on my cars radio like timer, mute and others work well ( okay mute cannot be more muted ). So I tried 1/8 headset for music it works, did not try yet one with a mic, but I'll do it ASAP. I tried to reprogram with odin default OS, with factory settings, and that way force all components to be re-write ( Bootloader, Radio , etc ), issue still present !!! Try to clean micro usb connector, nothing !! Try to clean audio jack, but wasn't really sure if it was well cleaned.
Do anybody here have an idea of what I could try, test or do to eliminates possibilities ??
I am thinking that maybe some corosion could be in the audiojack, somewhere and let the phone think that there is an audio jack connected, and then sent the voice to it...but how it could be tested before to try to open the phone to clean it properly and risk to damaged the LCD ???
Thank a lot for all of your advices
Related
Well, I wouldn't be in as deep of a trouble if this were my phone... But I suggested the Mini to my GF.
Anyway, she was using headset earlier today and after she removed the headset, the phone is stuck in headset mode. Meaning no voice coming thru the phone's earpiece on both incoming and outgoing calls. She tried the headset again and voice is coming thru headset without problem, but once removed, it's still stuck. How do I get the phone out of headset mode please???? Anyone has similar problem before??? Please help!!!
Reply
hey hi ,
There are many ways of fixing this -
1)softreset
2)turn bluetooth off! if you are talking about bluetooth headset
3)where it says enable bluetooth headset on today screen - disable it
These might help you!
Regards
AMD
The socket has probably jammed internally, try insert pull out a few times making sure you pull sharply when removing, if this fails try inserting something slightly smaller and jiggling it about. I have also used a tiny squirt of WD40 which is like an easing oil for rusted or obstinate nuts/bolts/screws, also you can buy a spray called switchgear which is used for electronic components such as volume sliders/switches etc when they become sticky and operate intermittently. This is a well known problem on the xda 2.
Thanks guys, it's not BT and this is after many soft-reset I'll give WD-40 a shot. Thanks again!
I've got exactly the same problem here. My phone is bonded to a BT headset. Forgot to bring the headset and found that no sound, or extremely small volume, was coming out from the phone. Tried soft reset, deleting the bond etc. none of it works.
Would be interested in knowing what's the real underlying cause if anyone finds it out.
Hey Solitary, I'm in HK as well and I think it's a hardward rather than software issue. Coz. if I pull the headset, the normal clicking sounds can be heard from the phone, just not during voice calls, I think the earphone on the phone is somehow dead, looks to me like cold soldering
I'm calling O2 in the morning and demand an exchange, my GF only had this phone since 1/9 and besides this, on the unit we have, the voice quailty is also bad too
Hi, CL55,
You might want to read this:
http://www.coolsmartphone.com/index.php?option=articles&task=viewarticle&artid=58&Itemid=3
It seems it is an old and common problem for smartphones.
I've also read in a Taiwan forum that they have got exactly the same problem in Taiwan for the Dopod818.
But I wonder if it is hardware related. My problem is that I'm stuck in a BT headset mode, and I'd never touched the hardware headset socket. So either I have a different problem than yours or else it seems it's more likely a software problem.
Anyway, do tell us if you manage to solve it.
Can you confirm if you can hear the clicking sound from the buildin speaker now? Only no voice from the earphone, or no clicking sound from the buildin speaker as well? I really suspect I have a different problem
Yes I can hear all other sounds from the speaker loud and clear, except for talking over the phone.
So it seems I've got a BT software (or my BT phone hardware) problem but you've got a Mini hardware problem.
I was listening to some music through my headphones on my jam and I got a call, so i pulled the headphones out of the jack. Once i did that no sound would come out of the speakers, not even after many soft resets. I could still hear sound when i put my headphones back in, but nothing when i took them out. Then i tried making a call and pulling the headphones out of the jack while in the call and that fixed it. It must put the hardware in some bad state if you pull headphones out when there's a call?
i had this problem to but i've fixed it! hard resets doesn't seem to work so i pulled the battery out for a night and my speaker was working again try it!
Hi all, i have a problem after upgrade my SPV C600 from WM5 to WM6.
after finish the upgrading, i could play my windows media player and could make a phone call without any problem.
after a while after i plug in my earpice to listen music, it went good as well.
after plug it off (earpiece not attached), when i play windows media player, i cant hear anything and i try to make a phone call also the same, no sounds came out from speaker and from loudspeaker as well. but when i plug in the earpice everything goes smoothly, meaning that i can listen music and communicate with others when make a phone call.
before that i tried to ensure whether i face the software or hardware problem by setting the ringtone (start->setting->sound). but the sound could come out from the speaker.
after that i guess that the speaker (hardware) has no problem.
as to play windows media player and setting ringtone are using the same speaker.
can anyone tell me whats happening with my phone?
i believe that it is software related problem.
thanks in advance
my advise is to reboot your phone at me this works...
Profy_X said:
my advise is to reboot your phone at me this works...
Click to expand...
Click to collapse
i have tried to reboot and hard reset as well
but i can only listen music and make a phone call when i use my earpice
Please state which ROM you are using, we recommend Andot's PEE
I too have this exact problem any solution other than hard reset - dont need the pain of downloading resinstalling all my stuff - especially if its going to happen again.
Si
Tornado mic and speaker for phone not working
It rings and plays sounds but it appears that the hardware microswitch that sets it to wired-headset mode is stuck. I cannot set it back. Also: it switched into this mode when I rebooted (soft). I did not add or remove a 2.5mm jack. Is there a registry setting to override the microswitch sensor and keep it out of headset mode?
Hi, this is my first post and hope helpfull everybody, possibly i was the same problem over ALL ROM (wm6 & wm6.1), searching for any solution (my specific trouble was that if i wanna listen music over any player: ( a.k.a windows media, pocket player, etc), i dont had a normal sound from the speaker, the sound was distorsioned, low... horrible, the only solution was insert the plug from the headset and out , but, power off the phone and... again, sucks really ), i return to a Wm5 Rom (imate) and solve the problem, but, tired for the slow performance of WM5, search for other rom, sacrify the music listen ( but i have a good mp3 player...), and, the same problem.
I found in the web (no remember the page) that the SRS plug-in anytimes cause troubles with the sound output, i try to install any ROM WITHOUT this complement, the ROM from Rickywatt Tornado Neo/shadow no have this plugin, install and ...Eureka, no more the issue, follow my instint, i install the SRS plug in, reboot and... the fuc%$& problem, hard reset and the phone witout the problem... conclusion, the SRS was the monster.
You can try this "method", most of rom carry or include from the "kitchen" this SRS dll, but installing the rom from Rickywatt (fast, clean... beautiful, only without the spanish lang, but, nothing is perfect...), can solve the issue, for me ,cors, i dont know for you (my phone is a HTC sda).
For the mic, really i dont have idea , any bad registry, entry, etc :-(, i never have this issue, good luck...
Greetings from colombia (sorry for my poor English)
mzzw said:
It rings and plays sounds but it appears that the hardware microswitch that sets it to wired-headset mode is stuck. I cannot set it back. Also: it switched into this mode when I rebooted (soft). I did not add or remove a 2.5mm jack. Is there a registry setting to override the micro switch sensor and keep it out of headset mode?
Click to expand...
Click to collapse
That's not controlled by software. Try plugging and unplugging a headset several times, twisting it around to clean the contacts. It should clean and close contact for built in speaker to work again. Think of a circuit. If its closed, you have built in speaker. If it opens and you have a headset pluged in, then audio flows thru the headset. It won't go back to speaker until that circuit is closed again. Its mecanical, not software, so you can't do anything with registry.
mzzw said:
It rings and plays sounds but it appears that the hardware microswitch that sets it to wired-headset mode is stuck. I cannot set it back. Also: it switched into this mode when I rebooted (soft). I did not add or remove a 2.5mm jack. Is there a registry setting to override the microswitch sensor and keep it out of headset mode?
Click to expand...
Click to collapse
the same for me
well
the only fix i got was to disasemble and remove the swithch leaving its contacts as exposed as possible, the soldered a wire between 2 of the 3 connectors, hey presto all working, headset hole then filled with glue from glue gun
very rough but it worked....
as an after thought though see if youve updated your radio software, stranger things have happened if youve been into flashing with 3rd party roms
sisniper said:
well
the only fix i got was to disasemble and remove the swithch leaving its contacts as exposed as possible, the soldered a wire between 2 of the 3 connectors, hey presto all working, headset hole then filled with glue from glue gun
very rough but it worked....
as an after thought though see if youve updated your radio software, stranger things have happened if youve been into flashing with 3rd party roms
Click to expand...
Click to collapse
Thank you!!! The only problem that i've now it's buy a torch :S
Hi if someone can help me it would be much appreciated. I just bought a Touch Pro and everything is working fine....except for one really annoying issue.
Whenever I connect my bluetooth to a headset, it shows connected but no sound is coming out. The sound is muted. when connected to my Audi, I see that the phone has bars (shows connected and I can dial the phone), but when I make a call no sound. Similarly on my SE HBH-DS970 headset. The A2DP works perfectly, but when I make a call nothing.....I've searched google and through XDA and no solution.
Can someone suggest a solution? I've soft/hard reset the device already. If I should change Radio ROM which one would someone suggest that's stable? Thanks
If no one else has this problem, can anyone at least suggest to me if this sounds like a Hardware or software issue? If hardware I will return it, but if software I will try to find a solution. Like I said the phone connects to BT, but I just can't get handsfree to work. File transfers and A2DP work. Thanks
Just flashed to UK ROM and still no help....I've read some people having the same problems over at the Diamond thread...I'm the only one answering my own thread here hahaha....if anyone can help I'd greatly appreciate it. Thanks.
Hi,
I occasionally had such an issue with my Parrot CK3100, but I did not get the time yet to investigate further. After the call was connected I did not hear anything, and I am not sure whether the other party could hear me.
On another day, the handsfree was working perfectly OK.
Cheers
Michael
Thanks for replying Michael....I'm at a loss and I tried all the suggestions posted. I hope it's a software issue...I'm going to buy a bluetooth headset tomorrow and see if that works. It's not the end of the world, but annoying since all my ppc, s60, BB, and UIQ phones prior to the TP have not had any such issues.
Do you think it's a software issue?
have you tried playing music?
Yes.....A2DP works perfectly....no problems whatsoever with file transfers either....I'm guessing either it's a software problem or the phone has a new bluetooth software that's not agreeing with my older SE headset, but the car is another issue. The Car is 2007 and I'm sure the Bluetooth software is not that old. I've tried Euro WWE and Asian WWE ROM and no go.....I'm going to try the Cingular ROM and see what happens.
Just another quick update....I tried 2 other different bluetooth headsets and still the same problem... for some reason the sound for handsfree will not come through...anyone know of registry hack possibly that will allow sound to come through?
May not be entirely related to your problem...
Mine is worst...whenever I have paired my Jabra or iTech BT headset, when the phone rings, 8/10 times the phone will auto pickup (and no I did not setup the phone to auto pickup) and the it will NOT connect to the bluetooth. Instead it will be just like an auto pickup and the sound will come thru the phone headset. This is driving me nuts!!!!
My wired headset has never worked like in Windows Mobile. Polaris just refuses to play music through it. I think developers are working on this, but some users have found workarounds that work.
I created this topic to keep track of this issue in order to give it the importance I think it has. I hope you think the same.
I also agree that this issue deserves more attention from the developers, especially because, at least for me, is the main inconvenience with Froyo at the moment (this and the related issue with usb mounting and adb).
I can confirm that one workaround is to plug either the headset or usb in recovery mode and then quitting into android, after that it works as normal until the next reboot, in the sense that if you unplug and replug the headset / usb it will recognize it. I don't know if it will be hard to fix, but it seems that android cannot communicate with the usb port after fully booting.
Same problem here. The recovery mode workaround does recognize USB but it would not recognize my wired headset.
The working around for the wired headset RC W100
The headset is working with Incubus RLS12 only when you unplug the headset it isn't directly play on the phone speaker.
You have to stop playing (pause) and turn off (end key) the screen. Unlock the screen and start playing with the music on the phone speaker.
It isn't necessary to reboot with the headset connected to enable it.
Hi!
I can't get my wired headset to play music through it. Unless I've not understand the workaround it does not work for me. Here is what I've done:
- stopped the music player (while playing through phone speaker);
- switched off the display;
- connected the wired headset;
- start playin' again but it plays always through phone speaker;
Thank u.
I can confirm this issue.
I really love the work done with Android, but I can't use it as an MP3 player, because my wired headset doesn't work.
Is this known with the developers, and being looked in to?
Nothing new on this issue so far?
Up!
I am still ionterested in this issue!
I tried to do it my self but i failed, thought i'd put it as a challenge for someone if its possible or maybe if someone has already done it and maybe willing to share?
I've bought Logitech H600 headphones and it comes with microphone and a Bluetooth usb connector.
The problem i ran into is weird but i bet many of us would have gone through it before or probably somewhere been fixed but as i am not aware of where about thus thought to make a thread here to share with all.
Microphone & headphones works with computer and doesn't have any problem in making calls through skype and other apps using computer.
The real problem is with the phone..
1: The headset works perfectly it does connect with Phone and plays MEDIA files through headphones without any problem.
BUT!
2: it doesn't direct calls even though it has microphone, where i dont understand why would it work on PC and not on phone even though it does have headphones and microphone, is it possible to work things out for this like writing small script or an app to fix this issue some how?
I'd love to know if any of you guys have ran into this and have problem with this and dont want to lose the beloved headset...
Cheers in advance for all those who reply and try to resolve this issue.
still looking.