Database Info

FUNC BOOT Recovery or Kernel

hi dears
i have H60-L04 and need recovery my system
this error
Error!
Func NO: 10 (FUNC_BOOT_RECOVERY)
Error NO: 2
or
Func NO: 9 (FUNC_BOOT_KERNEL)
Error NO: 2
i use multitool for unbreak but problem not sloved
i use Hisuite to recovery system but this apps said this phone not support
my bootloader unlock and phone not gone in recovery mode just fastboot i install cmw or twrp recovery but not go in recovery or not flashing. just fastboot
please help me i need fix my phone thx

Stuck rescue mode, can't enter to bootloader

Hello everyone
I'm in a huge trouble, I flashed recovery partition using twrp on oreo firmware by mistake and now I can't enter to bootloader mode to reflash recovery using the extracted recovery.img from UPDATE.APP.
I already tried:
dload folder with UPDATE.APP and pressing volume down, volume up and power button
Press & hold power button and plug the USB cable
Neither of them work, and my phone is stucked in ERROR MODE saying:
Attention!
Plase update system again
Error!
Func NO: 11 (recovery image)
Error No: 2 (load failed!)
Please help, I do not what to do or at least enter to bootloader to reflash the custom recovery.

Hi, I have the same problem. Were you able to fix it?

plug in usb, hold power and vol down until you get to fastboot.
If you are on OREO now, make sure to extract recovery_ramdisk and recovery_kernel, and flash both in fastboot
fastboot flash recovery_ramdisk RECOVERY_RAMDISK.img
fastboot flash recovery_kernel RECOVERY_KERNEL.img
If you can't find RECOVERY_RAMDISK you're using a nougat update.app.

ante0 said:
plug in usb, hold power and vol down until you get to fastboot.
If you are on OREO now, make sure to extract recovery_ramdisk and recovery_kernel, and flash both in fastboot
fastboot flash recovery_ramdisk RECOVERY_RAMDISK.img
fastboot flash recovery_kernel RECOVERY_KERNEL.img
If you can't find RECOVERY_RAMDISK you're using a nougat update.app.
Click to expand...
Click to collapse
Hi,
I would like to know where to find RECOVERY_KERNEL.img, as there's no UPDATE.APP contains it.
I have the very same problem, but I managed to enter the fastboot though.
Another question, how to flash the erecovery partitions, it seems it has been blocked from access.
thanks.:good:

liuyujack said:
Hi,
I would like to know where to find RECOVERY_KERNEL.img, as there's no UPDATE.APP contains it.
I have the very same problem, but I managed to enter the fastboot though.
Another question, how to flash the erecovery partitions, it seems it has been blocked from access.
thanks.:good:
Click to expand...
Click to collapse
Woops. There's no recovery_kernel. There's ERECOVERY_KERNEL.
Recovery most likely uses regular KERNEL.
You can flash erecovery partitions in twrp, using dd.

ante0 said:
Woops. There's no recovery_kernel. There's ERECOVERY_KERNEL.
Recovery most likely uses regular KERNEL.
You can flash erecovery partitions in twrp, using dd.
Click to expand...
Click to collapse
Thanks for the explanation. however, to leave the error mode, I flashed recovery_ramdisk, ramdisk, kernel, and system, but it still stuck there the moment I leave the fastboot with the same error code.
Do you know why this is or have any solution?
Thanks.

liuyujack said:
Thanks for the explanation. however, to leave the error mode, I flashed recovery_ramdisk, ramdisk, kernel, and system, but it still stuck there the moment I leave the fastboot with the same error code.
Do you know why this is or have any solution?
Thanks.
Click to expand...
Click to collapse
Same error code as: Error!
Func NO: 11 (recovery image)
Error No: 2 (load failed!)
?

ante0 said:
Same error code as: Error!
Func NO: 11 (recovery image)
Error No: 2 (load failed!)
?
Click to expand...
Click to collapse
yes, exactly

ante0 said:
Same error code as: Error!
Func NO: 11 (recovery image)
Error No: 2 (load failed!)
?
Click to expand...
Click to collapse
liuyujack said:
yes, exactly
Click to expand...
Click to collapse
additional information:
fastboot oem lock-state info
...
(bootloader) FB LockState: LOCKED
(bootloader) USER LockState: UNLOCKED
OKAY [ 0.007s]
finished. total time: 0.007s

as: Error!
Func NO: 14 (no image found)
Error No: 2 (load failed!)
similar one here. Is there any solution?

liuyujack said:
yes, exactly
Click to expand...
Click to collapse
Hi !
Did you find a solution ?

I have the same errors, Desperately looking for a solution.... Did anyone get it figured out?
Thanks

I finally figured it out. Hopefully this will help somebody else. I ended up fixing it by using DC unlocker. That Basically got me to where I could boot into erecovery. It also allowed me to use ADB to flash TWRP. From there I just flashed the entire hwota8 package. I'm back up and running thankfully. Once again, I really appreciate you and people like you who help others on this forum.

seti007 said:
I finally figured it out. Hopefully this will help somebody else. I ended up fixing it by using DC unlocker. That Basically got me to where I could boot into erecovery. It also allowed me to use ADB to flash TWRP. From there I just flashed the entire hwota8 package. I'm back up and running thankfully. Once again, I really appreciate you and people like you who help others on this forum.
Click to expand...
Click to collapse
Could you do a guide for that?

Has anyone found a solution.? Im about ready to jump the gun on dc phoenix. But if someone found an alternative, it would really help.

[SOLVED] bricked, ERROR MODE NO11, NO2

[solved]
so I have rebranded from l09 to DL00 to take the opreo update with succsess
-flashed RR Os form openkirin
-instaled magisk and rebooted
now im stuck at error mode:
Attention!
please update system again
android logo
error!
Func NO:11 (erecovery image)
Error NO :2 (load failed)
I can boot to fastboot and boot to erecovery but can't factory reset from erecovery (gets me back at error mode)
cant boot to twrp
I've tried to flash 320twrp but nothing chenged
tried to flash rom again but bithing changed
please help!
SOLVED using fastboot: flashing from the same firmware that you bricked - kernel, system, cust, recovery_ramdis

The problem is magisk, uninstall it

Elkkooz said:
The problem is magisk, uninstall it
Click to expand...
Click to collapse
how to install it when i can't boot to OS
?

Jelke997 said:
so I have rebranded from l09 to DL00 to take the opreo update with succsess
-flashed RR Os form openkirin
-instaled magisk and rebooted
now im stuck at error mode:
Attention!
please update system again
android logo
error!
Func NO:11 (erecovery image)
Error NO :2 (load failed)
I can boot to fastboot and boot to erecovery but can't factory reset from erecovery (gets me back at error mode)
cant boot to twrp
I've tried to flash 320twrp but nothing chenged
tried to flash rom again but bithing changed
please help!
Click to expand...
Click to collapse
Flash twrp by the following command,
fastboot flash recovery_ramdisk <your file as usual>

boris dmello said:
Flash twrp by the following command,
fastboot flash recovery_ramdisk <your file as usual>
Click to expand...
Click to collapse
nope, tried that.. it just gets me back into same error mode

HI,
Could you please share the fastboot commands to flash kernel, system, cust? Thanks.

[email protected] said:
HI,
Could you please share the fastboot commands to flash kernel, system, cust? Thanks.
Click to expand...
Click to collapse
fastboot flash krenel KERNEL.img
fastboot flash cust CUST.img
fastboot flash system SYSTEM.img

Jelke997 said:
fastboot flash krenel KERNEL.img
fastboot flash cust CUST.img
fastboot flash system SYSTEM.img
Click to expand...
Click to collapse
Hi,
Is it same for Oreo?

Solved How?

boris dmello said:
Solved How?
Click to expand...
Click to collapse
Bottom of OP message:
"SOLVED using fastboot: flashing from the same firmware that you bricked - kernel, system, cust, recovery_ramdis"

Help Mate 9 MHA-L09C432B368 Stuck in Error mode 11 recovery image 2 image failed

I would like to tell you my problem, I have a Mate 9 MHA-L09C432B368.
After several attempts and letting the battery drain I could enter Fastboot mode, I have the FRP unlocked and I could unlock the bootloader again, the problem is that I can not enter either the TWRP, or to recovery mode, try flashing again the same TWRP I had installed it well but still when I want to enter after passing the Huawei logo it remains on the white screen of ERROR MODE, Func NO: 11 (recovery image) Error NO: (image Failed!) Reading other forums and looking I have been told a lot by Internet that it is necessary to make the Dload method try it but it did not work, I understand that it does not work in this model but I still try it.
I also did a flash with all the files as I found in XDA
"When you have system extracted, flash it in fastboot using fastboot flash system system.img.
Do the same with KERNEL, extract and flash to fastboot flash kernel KERNEL.IMG
(BOOT is now split into RAMDISK and KERNEL)
Recovery was split to recovery_ramdisk, recovery_vendor and recovery_vbmeta
Boot was split into ramdisk and kernel
Recovery2 (erecovery) was split into erecovery_ramdisk, erecovery_kernel, erecovery_vendor and erecovery_vbmeta
fastboot flash ramdisk ramdisk.img. Kernel flashed as fastboot flash kernel kernel.img.
Recovery ramdisk as fastboot flash recovery_ramdisk recovery_ramdisk.img "
I'm still stuck on the same screen with error 11 and 2 I made the flash of the recovery that I used when I put version 368 are two MHA_RECOVERY_NoCheck.img and MHA_RECOVERY2_NoCheck.img both give Failed using the command Fastboot flash recovery_ramdisk RECOVERY_XXXX with both the same without using the _ramdisk command is equal I'm still stuck in the same state.
Does anyone have an idea that another method I can try?
I will thank you very much.
You can flash all * .img through ADB and in this case there is a specific order to do it, check several threads but I did not get an answer and search but I could not find anything, it is worth noting that when I flash files I mentioned before all OKAY but on power up it goes back to error 11 and 2 I have been told that it is a partition problem but I could not find something to recover them, there is some method that is missing or maybe an error in the steps I am doing ? I still can not access the TWRP but I can access without problems by ADB.

Help
Hello how are you. I had the same problem, I could not access to erecovery or recovery and worse to the system. only ERROR MODE appeared on the screen, Func NO: 11 (recovery image) Error NO: (image Failed!) .. could enter fastboot mode. with PHONE Unlocked and FRP Unlock but I took it to the official technical service of my country and they told me that it had no solution. at the time of testing on my computer I was left with PHONE Relocked and FRP lock in the fastboot. I have the code of my Bootloader and the FRP even though I can not unlock it to install files to my phone. help

hybrid09 said:
I would like to tell you my problem, I have a Mate 9 MHA-L09C432B368.
After several attempts and letting the battery drain I could enter Fastboot mode, I have the FRP unlocked and I could unlock the bootloader again, the problem is that I can not enter either the TWRP, or to recovery mode, try flashing again the same TWRP I had installed it well but still when I want to enter after passing the Huawei logo it remains on the white screen of ERROR MODE, Func NO: 11 (recovery image) Error NO: (image Failed!) Reading other forums and looking I have been told a lot by Internet that it is necessary to make the Dload method try it but it did not work, I understand that it does not work in this model but I still try it.
I also did a flash with all the files as I found in XDA
"When you have system extracted, flash it in fastboot using fastboot flash system system.img.
Do the same with KERNEL, extract and flash to fastboot flash kernel KERNEL.IMG
(BOOT is now split into RAMDISK and KERNEL)
Recovery was split to recovery_ramdisk, recovery_vendor and recovery_vbmeta
Boot was split into ramdisk and kernel
Recovery2 (erecovery) was split into erecovery_ramdisk, erecovery_kernel, erecovery_vendor and erecovery_vbmeta
fastboot flash ramdisk ramdisk.img. Kernel flashed as fastboot flash kernel kernel.img.
Recovery ramdisk as fastboot flash recovery_ramdisk recovery_ramdisk.img "
I'm still stuck on the same screen with error 11 and 2 I made the flash of the recovery that I used when I put version 368 are two MHA_RECOVERY_NoCheck.img and MHA_RECOVERY2_NoCheck.img both give Failed using the command Fastboot flash recovery_ramdisk RECOVERY_XXXX with both the same without using the _ramdisk command is equal I'm still stuck in the same state.
Does anyone have an idea that another method I can try?
I will thank you very much.
You can flash all * .img through ADB and in this case there is a specific order to do it, check several threads but I did not get an answer and search but I could not find anything, it is worth noting that when I flash files I mentioned before all OKAY but on power up it goes back to error 11 and 2 I have been told that it is a partition problem but I could not find something to recover them, there is some method that is missing or maybe an error in the steps I am doing ? I still can not access the TWRP but I can access without problems by ADB.
Click to expand...
Click to collapse
I think I can help the same happened to me. Is FRP still unlocked?

Re: I stuck with my Mate 9 Error mode numbers 11 and 2
Newrooter22 said:
I think I can help the same happened to me. Is FRP still unlocked?
Click to expand...
Click to collapse
Hi my phone have bootloader and FRP unlocked you can fix your phone for this error mode 11 and 2 ?

I wanted to ask please if this Thread can be closed since I could solve the problem, I share the solution which I obtained through a partner of the website HTC Mania @rodrigocarlosqm to which I am immensely grateful. Thanks to your generosity I was able to recover my phone and I do not want as a paperweight, the arrangement was simple buy credits in dc phoenix, in my case download the official version oreo 368, extract the update.app file and place it in the flashing program, restart the cell phone, in case it does not do so automatic do not panic turn it off and let it turn on normally, enter the recovery stock, make a wipe, then restart and return to the recovery in this case make a wipe hard reset, restart and terminate once that happens the phone it will restart again and once this is done, the operating system will start without any inconvenience. Thank you very much to everyone who helped with the help and ideas. I could find the result and I would like to thank @rodrigocarlosqm again, he was the one who helped me recover the brick he had. For all those who are in the same situation please I hope you can solve it before any query is at your disposal. Thank you all.

Error! Func NO : 11 (reovery image) Error NO : 2 (load failed!)

Hey!
Today I installed open Kirin's omni rom pie alpha 5.2. The system works, but then I tried installing twrp using fastboot flash recovery. That one didn't work so I tried fastboot flash recovery_ramdisk. It finished successfully but now when I boot to recovery I get:
Error!
Func NO : 11 (reovery image)
Error NO : 2 (load failed!)
OS works, but recovery doesn't. How can I fix this? Thanks in advance.

TWRP is not supported by OK ROMs. This information is widespread.