Hi, i tried to flash my bricked phone (Lenovo a7000-a) via my laptop with Windows 10. I installed drivers for mediatek, and in SP Flash tool set setting "Usb Checksum, Storage Checksum" to true. Then i insert scatter with stock ROM, and click to "Download" button.
Then i pressed VOL + button on phone and connected it to computer.
Then PC recognized "Mediatek USB Port" (on image *1*). After ca. 5 seconds this device disconnected. And after ca. 5 seconds connected "Unknown USB Device (Port Reset failed)" (on image *2*)
And here flashing stucks at "Download DA 100%" (on image *3*)
Image:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I tried another usb cord, and same.
i tried also flash on another computer and SP Flash Tool said: "BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)" and flasing didn't started.
Where i do a mistake? I would be very grateful for any help. Many thanks!
Powering said:
Hi, i tried to flash my bricked phone (Lenovo a7000-a) via my laptop with Windows 10. I installed drivers for mediatek, and in SP Flash tool set setting "Usb Checksum, Storage Checksum" to true. Then i insert scatter with stock ROM, and click to "Download" button.
Then i pressed VOL + button on phone and connected it to computer.
Then PC recognized "Mediatek USB Port" (on image *1*). After ca. 5 seconds this device disconnected. And after ca. 5 seconds connected "Unknown USB Device (Port Reset failed)" (on image *2*)
And here flashing stucks at "Download DA 100%" (on image *3*)
Image:
I tried another usb cord, and same.
i tried also flash on another computer and SP Flash Tool said: "BROM ERROR: S_BROM_CMD_STARTCMD_FAIL (2005)" and flasing didn't started.
Where i do a mistake? I would be very grateful for any help. Many thanks!
Click to expand...
Click to collapse
did you find answer? i have excact problem
Gigageo said:
did you find answer? i have excact problem
Click to expand...
Click to collapse
This isn't hard to find with a search for
"BROM error SP flashtool"
https://forum.hovatek.com/thread-439.html
Learn to use Google with simple search terms for exactly what you're looking for, as in my example above, you're using SP flashtool and you had an error, which is exactly what I searched for. You're almost guaranteed to find something. The link I gave you was the first thing listed at the top of my search results, my simple search took me straight to what you needed, it could not have been any easier than that.
That tells me that you didn't try to look, or you did look but didn't try very hard or didn't use your head when you looked.
Sent from my LGL84VL using Tapatalk
Related
Hay. This is my first post in xda and i don't speak english.
I have chuwi vi7 and windows 7 but i can't flash the tablet.
When I connect chuwi with PC appear 3 new cdc serial and 1 adb.
After installed many driver apper this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I take FlashTool_E2 from this
r_e_n_e said:
I left dummy IMEI. I used this one ROM from
Code:
https://yadi.sk/d/BFxcO0briMMyi
Flashed and WiFi works!!! So everything was wrong ROM!!!
Click to expand...
Click to collapse
and the firmware from this
stegg said:
a new firmware has been released
Code:
https://yadi.sk/d/6boIFS_-jsLkm
it should solve the random-freeze deep sleep problem
I flashed it with instructions in first post and everything was OK, i didn't loose imei :good:
Click to expand...
Click to collapse
When I start FlashTool_E2 the corner left-bottom is pink!?!?!
If I start the "usb map wizard" don't finds any connection.
If I do "start" and clik on "USB1" it give me
An EBL must be injected. None was found in the downloaded file.
For some systems there must be an injected EBL. The file specified for download does not contain an injected EBL.
Check that the file is correct for the target. This error can also occur on a normal boot time out, in which case just try again.
Click to expand...
Click to collapse
and if clik on "USB4" it give me
Error during boot
An error happened during the boot sequence.
This could be physical transmission error. Check connection and COM port and try again. If the error persists contact the developer.
Click to expand...
Click to collapse
Could someone help me please?
Sorry for my english.
Adijazz1706 said:
Tablet off, then press start usb1 before connecting phablet. after pressing, quickly connect tablet and hold vol-. If not work, try vol+ or power button. Keep trying.
Click to expand...
Click to collapse
Vary vary good. All Ok. It was vol+. Transmission ok. Upgrade ok. Imei ok.
Tanks a lot.
I have two Vi7 tablets and after firmware update they both have the same MAC address 0a:0b:ad:0d:00:d8 and cant be used on network at the same time.
Any solution to be able to change MAC address on either of the tablets ?
Hello
I think I read everything what was written on this forum about flashing Vi7 but I still have a problem. I can not find an apropriate drivers for CDC, and even Intel(R) USB flash loader doesn't work correctly.
Could you help me? Is there anybody who has a package of driveres for win7 64 bit?
The driver
Can you please give me the driver link for CDC?
on the device manager I have:
one port as "Android device" -> "android bootloader interface"
after i install the ADB installer from here http://forum.xda-developers.com/showthread.php?t=2588979
(the fastboot doesen't work for me...)
but the other 3 ports are ander the "Other Devices" and no driver...
Can you please give me the drivers for the rest. and explain?!
Thanks
Sahara fail error occurred in lenovo k5 plus...
XDA Visitor said:
Sahara fail error occurred in lenovo k5 plus...
Click to expand...
Click to collapse
i have not tried this method but this is what i could come across while searching in xda forums....
you may also register yourself at XDA and search more or check this thread http://forum.xda-developers.com/android/general/unbrick-vibe-k5-plus-qfil-qpst-method-t3467830
IMPORTANT : First of all you should always have all the drivers installed on your PC.
READ EVERYTHING CAREFULLY AND MAKE SURE YOU HAVE FOLLOWED THE STEPS CAREFULLY AND THEN POST QUERIES.[/COLOR]
The following drivers are needed for this task:
1. Lenovo USB Drivers.
2. QDLoader QFIL Drivers
Search for them on google and you will find them very easily. Most of the time they are there in the stock rom zip folder under a folder named Drivers.
Install all of them.
1. Download the Stock ROM you need for your phone from here:
DOWNLOAD STOCK FIRMWARE (Thanks to Shreps)
2. Extract the above zip to a folder. You will get three folders: Drivers, Images and Tools.
3. From the Drivers folder, Install all drivers.
4. From the Tools folder, install the QPST Tool. In your Start Menu it will come as QFIL. Don't worry about that.
5. Power Off your device.
6. Open QFIL TOOL.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
7. Now On top you will see two options: 1. Flat Build 2. Meta Build
Select FLAT BUILD
8. In "PROGRAMMER PATH" click Browse and go to the folder named Images and select the one file it displays (something like prog_emmc....mbn).
9. Now click "Load XML" and select "rawprogram0.xml" file and then another dialog box will open. Here select "patch0.xml".
PC WORK IS DONE. DO NOT CLICK DOWNLOAD.
Your device should be switched off.
NOTE CAREFULLY: Hold "VOLUME UP + VOLUME DOWN" key (Do not press POWER button). and connect the USB Cable from PC to the phone.
Your phone should now display RED LED LIGHT and the QFIL Tool should now change from NO PORT to QUALCOMM.....Something like that.
You are now ready. Click on Download button on QFIL TOOL and then wait for atleast 15 minutes.
After the dialog at bottom shows "DOWNLOAD SUCCESSFUL" in blue color, UNPLUG your device. Wait for a few seconds or a minute and then POWER ON your device.
First boot takes about 8-10 minutes.
I am trying to unbrick my friends phone. Phone decided to brick itself yesterday morning. SScreen is dead for the most part. Only when trying tp charge it sometimes Battery too low let the device charge for a while screen shows up. else nothing happens.
I have installed the qualcomm drivers.
I have downloaded the decrypted image.
I run MSMdownload tool. but the device connection stats shows N/A.
In device manager, Under ports
Code:
Qualcomm HS-USB QDLoader 9008
Shows up. But the device does not show in MSMdownload tool. see attached image.
what am I missing here?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
xeltos said:
I am trying to unbrick my friends phone. Phone decided to brick itself yesterday morning. SScreen is dead for the most part. Only when trying tp charge it sometimes Battery too low let the device charge for a while screen shows up. else nothing happens.
I have installed the qualcomm drivers.
I have downloaded the decrypted image.
I run MSMdownload tool. but the device connection stats shows N/A.
In device manager, Under ports
Code:
Qualcomm HS-USB QDLoader 9008
Shows up. But the device does not show in MSMdownload tool. see attached image.
what am I missing here?
View attachment 5291079
Click to expand...
Click to collapse
You have to be on Test mode on your computer. In Bottom right corner of your Computer should look like below. The Exclamation mark over the port name shouldn't be there.
Detail Instruction Has been been provided in the link below
[TOOL] MsmDownloadTool V4.0 International (Oxygen OS 5.1.5)
You can use it to revive your op6, if you can boot in fastboot and have done the stuff with drivers (qualcomm) MsmDownloadTool V4.0 International (Oxygen OS 5.1.5) May 2018 Android patches https://mega.nz/#F!CfBG0IgZ!Gmnu6B-a7yFyvMLNw_pz8w...
forum.xda-developers.com
I have the same issue even tough I am in Testmode.
change port from 25 or up to 1 or 2 its worked
pro change port from 13 to 1 or 2 its work
Hello everybody!
Yesterday, on 28 of December, I had a massage on my BV4900 pro that a systemupdate is now ready to be installed.
After download of 2,48 GB file the installation went on, the phone started in the next step. On the screen was this white circle and the installation-progress was shown under. After the update was completted, the phone didnt start. The screen ist black. I cannot do anything with it. I tried to flash the firmware or at least the preloader with sp-flash-tool, but cannot. The connection to sp-flash-tool is with 100% but then I see under device-manager is "Media Tek PreLoader USB VCOM (Android)". So the flash-tool does not flash. I tried with volume buttons to stop the battery-loading, but withou sussess. What can I try more to save the phone?
Some more informations: The red LED ist on, when the phone ist connected to pc or power-supply. The phone was rooted. The last android version: 12
And maybe this picture will help:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Just a Hint:
Do not flash preloader! preloader is responsible for preloader mode (which used by SP Flash Tool)
Do not use "Format all + Download" option. Formatting whole emmc will brick device.
regarding your issue. follow the recommendations of your screenshot.
aIecxs said:
regarding your issue. follow the recommendations of your screenshot.
Click to expand...
Click to collapse
Yes, I did it already. Nothing helps.
I spend the second day with this problem and do not come forward.
you already tried another cable and another PC? then probably usb jack is faulty. you shouldn't flash anything via usb then!
I am not the one who told you - you could try other flash tools. do not flash, just try to read back for now...
https://www.xda-developers.com/bypass-mediatek-sp-flash-tool-authentication-requirement
https://github.com/bkerler/mtkclient
Somebody else, who maybe has an idea?
I found this discription of the error:
The phone seems always be on. With power button I can only "restart" it. How can I shut it down?
Is there a tool I can use for switch the phone off?
Or maybe cmd-command for shutting down the device on com-port? I cannot find anything in internet. Only with adb. But I have no connection to adb, the phone is over adb not rearchable.
Maybe someone can show me the test point for this smartphone?
Hello, I installed Pixel Experience Android 13 Custom ROM. But it had IMEI issues, So I decided to roll back. When I opened SP Flash Tool, It said Select the Format All + Dowload Tool. I did the exact, But then it said, Disable verified boot or unselect the "Preloeader, Tkv, Dtbo, Trnsfs" I did what they said, Then, I flashed it completely, It said OK, I tried to boot in my device, But it wont budge. I guess it's bricked? I tried downloading an older firmware like previous version of the firmware for the same model, Then I opened the MTK Auth Bypass tool, I opened it, It used to work, But now, It gives an error:
► Installing driver... [OKAY]
► Waiting for brom... [FOUND]
● DETECT AS MTK USB Port (COM5)
► Configuration port... [OKAY]
► Handshaking... [ERROR] UNEXPECTED RESPONSE: 0x78
How to fix this error, and what could the reason be behind the bricking of the phone over no REASON?
Please guide, as I dont want to spend more on this phone as I alr went to Tech Support and spent my money there.
Thanks
[Update]: Found the Solution after 6 months, All I needed to do is to disconnect the Battery and reconnect it. Full detail on the last point in this thread I created: Infinix Fix
Re-flash Stock ROM.
jwoegerbauer said:
Re-flash Stock ROM.
Click to expand...
Click to collapse
Dear Brother, I cant flash stock rom, unless I get the DA File, and I bypass the DA file, And the Bypass tool gives an error:
Handshaking... [ERROR] UNEXPECTED RESPONSE: 0x78
Is there anyway you could help me?
If phone can get connected by ADB then you connect computer and phone via USB-cable and run
Code:
adb devices
adb reboot sideload
adb sideload <STOCK-ROM-ZIP-FILE>
adb reboot
jwoegerbauer said:
If phone can get connected by ADB then you connect computer and phone via USB-cable and run
Code:
adb devices
adb reboot sideload
adb sideload <STOCK-ROM-ZIP-FILE>
adb reboot
Click to expand...
Click to collapse
ummm, i dont have custom recovery.....
if it could work without custom recovery plzz reply.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Carefully read posts.
can you flash via fastboot?
i may be saying something stupid, but I do not hwo ur device works lmao.
Arealhooman said:
can you flash via fastboot?
i may be saying something stupid, but I do not hwo ur device works lmao.
Click to expand...
Click to collapse
Ur Bio is relatable, lol, Btw, Yes, my android is fixed now, But its IMEI is unknown, Idk what to do now.
how did you fix it . i am stuck in the same thing
hello 00101 said:
how did you fix it . i am stuck in the same thing
Click to expand...
Click to collapse
I went to the tech support, I just saw him opening my mobile, maybe he disconnected the battery and reattached it, as disconnecting and reattaching battery resets usb connections.