Hello, my device ( GT-P3100 ) had problems with automatic reboot and battery issues. I tried to fix it by reflashing stock ROM ( means a reformat ), it worked. The device worked well until I decided to press Power button + Volume Down Button and wipe data partition. This caused my device to stuck in a "SAMSUNG" blue glowing logo for 20 minutes.
I decided to reflash the stock ROM again, but it ended up in a failure, and bricked my device with the message: " Firmware Upgrade Encountered An Issue. Please select recovery mode in Kies & Try Again. "
So I proceeded with the instructions, but end up in "This device does not support initializing". I tried to reflash the device over dozens of times but each time ended with the same log:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> system.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Things I tried:
1. Changing USB Ports.
2. Rebooting
3. Try to enter recovery mode ( never worked, just went back into FIrmware upgrade encountered an issue. Please select recovery mode in Kies & try again. )
4. Retry it without closing ODIN.
5. Retry it after closing ODIN.
6. Retry it without closing ODIN several times.
7. Disconnect the device and reconnect.
8. Use another version of ODIN.
( Almost same log, except this time its:
<ID:0/004> Added!!
<ID:0/004> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3100XXCME2_P3100OLBCME2_P3100DXDLL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
)
9. I didn't use USB Hub
I'm quite dissapointed right after I managed to restore it I bricked it again, can anyone help me out?
Related
Hey guys,
I've got a Samsung Galaxy Tab Pro and now i have a huge problem. I rooted it a long time ago and decided to install TWRP today via TWRP Managaer from Play Store.
I guess i did something wrong. After the app told me that the installation of TWRP was successful, i restarted the tablet. Now the screen says: "downloading, do not turn of the device". And i warted for about 1 hour and nothing changed. I cant event shut down the tablet. If I hold the Power key, it only restarts. The only thing i can do is go to ODIN mode.
But i am kind a newbie and i have no clues what to do now. Any help is welcome. Thanks guys.
Hi, thank you for using XDA Assist. You probably have to flash the stock firmware with Odin and start the process all over. Try here for help first, http://forum.xda-developers.com/gal...-how-to-root-install-custom-recovery-t3087451. Also see your device's forum here, http://forum.xda-developers.com/galaxy-tab-pro-12-10-8. That is the best place to get help in the future.
Hey, thanks for your help. I just tried to flash the stock firmware via ODIN. But it always says that it Failed.
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T520XXUANI1_T520DBTANI1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
I tried on differend USB ports and installed differend Drivers. I've no idea what i should do now.
Hi, the only other things I can suggest is to:
Re-download the firmware file and check its md5
It's good you tired different usb ports. Make sure they're the ones in the back of the pc and 2.0, not 3.0
Try different cables
Keep trying. Odin can be finicky. I've has it fail many times and then for some unknown reason it'll work.
Thread closed.
helo..
my tablet gt-p5110
cannot enter recovery (pwr+vol+) and download mode (pwr+vol-), but just stuck in "firmware upgrade encountered an issue, please recovery mode in kies & try again",but the device still connect and sync to odin.
I was using a pit file but when started there is an info from Odin that ''pit partition does not exist''.
when flashing use odin 3.07 with stock rom from samsung-updates.com / or cwm/twrp/chillpilz recovery for my device the flasher complete and pass..but after auto rebooting just got black screen,and if press power got back to firmware upgrade encontered an issue.
here the odin log :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3100XXCME2_P3100OLBCME2_P3100DXDLL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> MLO
<ID:0/004> param.lfs
<ID:0/004> Sbl.bin
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
tired use another odin version just get flashing FAIL and other gt-p3100 still stuck firmware issue
anyone can give me another solusion ?
i aready read all thread in forum xda about flashing/brick/recovery...but still no luck
Hi everybody!
I have a Samsung Galaxy Tab 3 Lite - SM-T110, and after I ran it until the end of the battery, I wasn't able to start it anymore. When I try to turn it on, it shows me the Samsung logo and then reboot, and keeps in this endless loop. I tried to unplug and plug the battery again, and this way I was able to charge it, but even with 100% of batery the behavior is the same. I tried to leave the battery unplugged for a few ours, but that didn't solve.
The Vol up + home + power also doesn't work.
The Vol down + home + power works, but I had no luck with ODIN.
First I tried to flash the TWRP file, but it fails with this message:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T110.TWRP.2.7.0.1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I've tried al ODIN versions and the result is the same. I've reinstalled the drivers a few times, but no luck.
I have tried to flash 3 different images, downloaded from different sources, but the result is aways the same:
Code:
<ID:0/004> Firmware update start..
<ID:0/004> timh.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> obm.bin
<ID:0/004> DTim.Recovery
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I read somewhere that ODIN won't work if the reactivation lock is on, and that could be the reason of my problem. But I can't get into the system to change any configuration.
Is there anything else I could do to recover my tablet?
I don't know if it makes any difference, but my tablet is brazilian.
Thank you!!
Hey,
I was successfully running LineageOS on my GT-N8010.
However, it froze at one point and I force turned it off, and ever since I just get the 'Firmware upgrade encountered an issue' screen. However, I am still able to get into download mode.
I'm now wanting to get it back to stock so I can re-try LineageOS on it. I have the stock image but if I try to install through ODIN I just get an error(posted below) and also on the tablet I get SW Rev. Invalid magic string.
Any idea how I could try sort it out?
In the details section of the download screen it shows;
ODIN MODE
Product name: GT-N8010
Current Binary: Samsung official
System status: Custom
Log:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Odin requires TAR files not image .
Flash stock rom via Odin .
Sboot.bin fail means you are flashing firmware with an older bootloader than is currently on the device .
JJEgan said:
Odin requires TAR files not image .
Flash stock rom via Odin .
Sboot.bin fail means you are flashing firmware with an older bootloader than is currently on the device .
Click to expand...
Click to collapse
Edit:
Looks like I didn't have the latest version, tried a newer one but it now gets stucks and after about 5mins of trying it stops at system.img;
Logs:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1746 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Stuck on system.img means odin not recognized your system partition..
And or change USB port change usb cable .
Make sure that you have the least official firmware for your device and if it still fails,
it looks like a eMMC failure.
This problem is very common on the N80XX devices.
I already had to replace hundreds of eMMC's on them.
Hello everybody!!!
The Galaxy Note 10.1 GT-N8000 of my friend don't work again, when it's powered on it shows a message
In english
Encryption failure
Unable to complete the encryption due to an interruption, reset the factory data (operation which erases all your data) before use. After resetting, try encrypting the device again
There is a button to do that, but nothing it's happen when i click
Recovery mode is not accessible to wipe data.
I try to flash some stock ROMs with odine but the flash failed
Odine3 log
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1401)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1787 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Anyone can help me please
NOTE : Model number GT-N8000
I think you should manage to enter Recovery Mode to reset the factory data.
Its failing on boot image probably due to different/ later boot .
As said recovery mode and FORMAT system data etc .
Then Odin flash latest stock rom .