I have majorly screwed up. I rooted my Samsung Galaxy s6 without any problems, it worked out fine. Today I wanted to go back to stock so I could upgrade to 6.0.1....Now I am screwed.
I unrooted my phone through the SuperSU app, which probably wasn't the best idea. It rebooted but stuck at the Samsung Galaxy S6 screen and wouldn't proceed.
I then went online to SamMobile and found the stock firmware for my phone. Halfway through, Odin crashed, wirst off with some sort of Write Error...I left it for 10 minutes or so, nothing else happened.
I rebooted my phone, it kept going into that same screen and wouldn't let me proceed.
I tried flashing again, now I have an error saying "No PIT partition detected"
Rebooted my phone once more, I now have a screen says "An error has occured while updating the device software. Use the Emergency recovery function in the Smart Switch PC software"
I tried again, that the info below is my latest result in which it states that some NAND Write operation has failed....
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920W8VLU3BOJ7_G920W8OYA3BOJ7_G920W8VLU3BOJ7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Related
Hello,
I have a problem.
I used my Samsung Galaxy GT-P6800 until yesterday.
Yesterday I downloaded the latest version of kies and I installed it.
When I plugged my tablet to the program kies, this told me that there was an update available. So I accepted the upgrade.
Unfortunately not been successful upgrade. So I tried to make the recovery of the old firmware. I receveid again an error. Kies tells me to call the service center.
Now I am a tablet that does not turn on and that only goes in odin mode by holding down the power button plus the volume down button.
It should not be in recovery mode because if I try to press the power button for 10 seconds nothing happens.
How could I resolve the problem?
My tablet is not rooted.
I don't know what is the problem because doesn't compare the code error.
I do not know if it depends on the driver. I do not know if it depends on something else.
But I would like to re-use my tablet. Help me, please.
well,
I have used Odin to install CWM 6.0.3.0.
Then I have tried to install a rom take here: http://forum.xda-developers.com/showpost.php?p=21930183&postcount=2
P6800OXALQ2_P6800XXLQ2_HOME.tar.md5
but i read this message on Odin app.
Odin Log:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P6800OXALQ2_P6800XXLQ2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.img
<ID:0/005> NAND Write Start!!
<ID:0/005> factoryfs.img
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
How can I resolve, please?
Hi, i have a Norwegian Samsung Galaxy S6 and tried to root it using the SM-G920F files from CF-Auto-Root but it didnt work and now my phone wont start with the message: "Recover is not seandroid enforcing" where it says "Samsunng Galaxy S6
Powered by Android". I have tried all the SM-G920F Stock firmwares here but unable to install them, maybe my device should have been rooted before this? Is there i way i can fix my phone now? I cant even shut it down anymore :/
I have tried to follow this guide: autoroot.chainfire but it didnt work and now i have tried to use the UK/spain/Every-Stock-Firmware-for-the-G920F-i-Can-Find.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOCZ_G920FVFG1AOC4_G920FXXU1AOCW_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
On the phone itself it says "SW REV. CHECK FAIL. DEVICE:2 BINARY:1
With red text.
Is what ODIN3 v3.10 is saying.
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
roydok said:
To shut down S6 from download mode press volume down + power button at the same time and hold until screen turns off.
After this you have an option to:
1. Bring your S6 bacck to Samsung for warranty repair.
2. Use a different USB cable or try a different USB port then reflash again.
I hope this helps.
Click to expand...
Click to collapse
It Says KNOX warranty void 1, this means that warranty is broken? I am going to get my original samsung s6 USB cable tomorrow to try.
Install twrp and port any costum room and you will fix your s6...
Or download newest version in sammobile of g920f stock firmware. You are failing at sboot. That mean bootloader in the phone os newer than the one you trying to install
Now it does not fail right away, but it still fails after a short while. Will the process fail if i don't do anything on the device itself? Because now it starts doing something in Odin, but returns fail after a while, but i am not with the phone as it is home right now.
This is what ODIN says now:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU2BOFL_G920FOJV2BOEE_G920FXXU2BOFJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> cm.bin
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img
<ID:0/005> modem.bin
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Try redownloading your ROM. There might be errors in the file resulting from the download.
Idk whats going on I used the odin3 download stock firmware to try to restore the phone after boot loop I tried to install TWRP custom recovery it didnt reboot into and so i tried to restore through odin3 and stock frimware and it says failed. Any ideas thanks
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920TUVU1AOCG_G920TTMB1AOCG_G920TUVU1AOCG_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
make sure re-partition is unchecked from the options tab.
Sent from my SM-G920I using Tapatalk
Try :
1. Using a different USB cable or USB port.
2. Redownload again your ROM as download errors can cause flash failures.
3. Lastly, consider bringing your S6 back to Samsung for warranty repair. Its free within your warranty period.
I hope this helps.
hi, i tried to install offcial firmware on my galaxy s6, but odin shows this message:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920FXXU1AOCV_G920FH3G1AOC1_G920FXXU1AOCW_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
plz help if you know what to do to fix it
dED
Ceca
up
up
Hello,
what version of android do you actually have and what do you want to have? For example you cant downgrade 5.1.1 to 5.0.2. What do you have ticked in odin?
Thanks..
i have stock 6.0.1 but its rooted, i want to get back to official firmware and just noticed that i downloaded 5.1.1. i have ticked auto reboot and f.reset time
Try another usb cable and another usb port. Sounds stupid but ODIN is known for failing for stupid crap like that. Also might want to try another version of ODIN and try another computer as a last resort.
Hi,
I am new here, I've read the sticky so this seemed like the right place to post so here goes,
I have a Samsung Galaxy Note 3 (SM-N9005) which I have attempted (very unsuccessfully) to root, I followed some steps that others have done on various youtube videos using Odin3 and kingroot but unfortunately I believe my phone disconnected from the laptop while it was in download mode and now on each attempt I am left with the below message on recovery mode:
Firmware upgrade encountered an issue, Please select recovery mode in Kies and try again.
I tried Kies and have since found several articles stating that kies will never work if you have rooted or tried to root your phone.
When i try to download a new ROM or the original firmware ROM using the desktop Odin3 it fails every time now with the below transcript:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGBPB1_N9005EVRGBPB1_N9005XXUGBOJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
I've read many posts around the web suggesting ways to fix it but everything involves being in recovery mode which i cannot do, does anybody have any idea what i should do? please let me know if you need any further info, hopefully I am just being stupid and it's a really simple answer!
siv4444 said:
Hi,
I am new here, I've read the sticky so this seemed like the right place to post so here goes,
I have a Samsung Galaxy Note 3 (SM-N9005) which I have attempted (very unsuccessfully) to root, I followed some steps that others have done on various youtube videos using Odin3 and kingroot but unfortunately I believe my phone disconnected from the laptop while it was in download mode and now on each attempt I am left with the below message on recovery mode:
Firmware upgrade encountered an issue, Please select recovery mode in Kies and try again.
I tried Kies and have since found several articles stating that kies will never work if you have rooted or tried to root your phone.
When i try to download a new ROM or the original firmware ROM using the desktop Odin3 it fails every time now with the below transcript:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N9005XXUGBPB1_N9005EVRGBPB1_N9005XXUGBOJ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
I've read many posts around the web suggesting ways to fix it but everything involves being in recovery mode which i cannot do, does anybody have any idea what i should do? please let me know if you need any further info, hopefully I am just being stupid and it's a really simple answer!
Click to expand...
Click to collapse
Greetings and welcome to assist. There are a few things it could be, you could try a different version of odin, it could be an older version of firmware you are flashing or a file has become corrupt. If you connect your phone to kies and select emergency firmware recovery then that will return your phone to stock
Good Luck
Sawdoctor