Related
Hey all,
So tonight I attempted to install the Unofficial AOKP Jelly Bean posted here: http://forum.xda-developers.com/showthread.php?t=1862156
Before doing that, I followed the instructions to Unlock, Recovery, and Root my One S here: http://forum.xda-developers.com/showthread.php?t=1583427
After following those instructions, I then followed the instructions for AOKP Jelly Bean however my sdcard couldn't be mounted and the phone was in a boot loop if I didn't boot into fastboot by holding down the volume - and power buttons.
I attempted these instructions below however I couldn't get a stock recovery flashed.
1) Use the All-in-One-Kit and flash your recovery back to stock
2) Boot into the bootloader and choose to "clear storage" and afterwards to reset to factory defaults.
3) Go back to the all-in-one-kit and flash a CWM recovery version again.
4) Reboot into recovery (CWM). Your /sdcard should now be mounted and visible.
5) Now, try the UTB rom (it worked for me), rename the zip file to something short (i.e. utb.zip), and push it to the sdcard using adb as follows:
Click to expand...
Click to collapse
Still caught in the reboot loop, I relocked and tried to run an RUU file found here: http://www.htconeforum.com/forum/ht...e-your-htc-one-s-back-100-stock-relocked.html
I was able to successfully re-lock the phone however every time I try to run the RUU file it comes back with an error about 3-5 minutes into the process.
At this point, my phone boots into fastboot. At the top I have "Tampered, Relocked, Security Warning." My HBOOT is 1.14.0004 and my Radios is 1.08ts.50.02.16
I would appreciate any help if there is a solution. Thank you for your time!
Update: Not sure if this is helpful or not, but whenever I try to do something with The All in one toolkit the cmd window says device not found. Also, when I try to boot into recovery from fastboot, I get a green downward and circular arrows before getting the red triangle and exclamation point.
Update: Running the RUU mentioned above fails at the Signature stage and the cmd prompt when trying to write recovery returns "signature verify fail"
Are you s4 or s3? what kind of computer you got? The drivers need to be installed. then read up how to use android SDK. Then retry to flash the stock recovery using the same steps in your quote.
Sent from my HTC One S using xda app-developers app
whozilla said:
Are you s4 or s3? what kind of computer you got? The drivers need to be installed. then read up how to use android SDK. Then retry to flash the stock recovery using the same steps in your quote.
Sent from my HTC One S using xda app-developers app
Click to expand...
Click to collapse
I am pretty sure I am S4 (tmobile USA). I am on a windows 7 home build, and the drivers should be installed (at least, I could use HTC sync before all of this). I'll definitely try again tonight. If anyone has any other suggestions they would be much appreciated!
Make sure HTC sync is NOT active on your pc. Try searching for the original version of one s all in one toolkit. It has the stock recovery. I'm pretty sure this unbrick method works for all hboot versions but don't take my word for it. Focus on your goal. Get stock recovery flashed. You can also try unlocking your boot loader again and using the all in one to reflash cwm. In some cases like mine. The unofficial cwm touch is the only successful flash I got. Ps. Try having your phone in fastboot. Plug in USB and see if it says "fastboot USB" then type your android SDK directory for your fastboot folder. For example open cmd
cd\
cd androidsdk\tools
androidsdk\tools fastboot devices.
Fastboot devices command will tell you if your drivers are working.
You can also type in adb devices instead of fastboot devices.
Hope this helps. But you probably already know this
Sent from my HTC One S using xda app-developers app
whozilla said:
Make sure HTC sync is NOT active on your pc. Try searching for the original version of one s all in one toolkit. It has the stock recovery. I'm pretty sure this unbrick method works for all hboot versions but don't take my word for it. Focus on your goal. Get stock recovery flashed. You can also try unlocking your boot loader again and using the all in one to reflash cwm. In some cases like mine. The unofficial cwm touch is the only successful flash I got. Ps. Try having your phone in fastboot. Plug in USB and see if it says "fastboot USB" then type your android SDK directory for your fastboot folder. For example open cmd
cd\
cd androidsdk\tools
androidsdk\tools fastboot devices.
Fastboot devices command will tell you if your drivers are working.
You can also type in adb devices instead of fastboot devices.
Hope this helps. But you probably already know this
Sent from my HTC One S using xda app-developers app
Click to expand...
Click to collapse
Thanks for the help!
Here are my results:
HTC Sync is not running. Fastboot devices returns a device ID so that seems good. When trying to flash a stock recovery (that I got on this forum somewhere, but can't remember where) it sends it ok but I still get "remote: signature verify fail"
I unlocked the device and flashed TWRP 2.2.2.0 with the all in one tool kit. This put me back into the boot loop mentioned above. Once I manually got back into the bootloader and selected recovery, I was able to get into the TWRP recovery. At this point, I am kind of worried about doing anything. I would like to be able to push AOKP Unofficial JB if at all possible. Any further guidance would be appreciated!
Please, please don't use the toolkit. It makes people find problems later on and not know a thing about what to do.
Sent from my locked, tampered ville
---------- Post added at 08:24 AM ---------- Previous post was at 08:23 AM ----------
Oh well, flash AOKP through TWRP and then reboot into bootloader and flash the boot.IMG.
Sent from my locked, tampered ville
usaff22 said:
Please, please don't use the toolkit. It makes people find problems later on and not know a thing about what to do.
Sent from my locked, tampered ville
---------- Post added at 08:24 AM ---------- Previous post was at 08:23 AM ----------
Oh well, flash AOKP through TWRP and then reboot into bootloader and flash the boot.IMG.
Sent from my locked, tampered ville
Click to expand...
Click to collapse
It is clear to me that I didn't do enough research before getting into this. I thought my experience with putting custom roms on my galaxy S (a phone I really disliked) would give me the appropriate background. Clearly I was wrong! I'm a little unsure how to flash AOKP through TWRP when AOKP is not on my SD card. In fact, when I look at the SD card in TWRP, the only file on it is "TWRP."
I think I need to flash TWRP 2.3.0 (rather than the 2.2.2.0 I have), because it supports ADB Sideload (talked about here on their site which I can't yet link to). Can I do that through the Android SDK like I have been doing? I don't need to do anything to the TWRP 2.2.2.0 before trying to flash 2.3.0 do I? It seems if I do that, I could send AOKP to my phone through adb when it is in recovery.
And just for my better understanding, what is different about flashing it in TWRP and then flashing the boot.img in fastboot?
Thanks again!
You have to fastboot push the AOKP zip through the bootloader I think.
Sent from my locked, tampered ville
Veritas327 said:
It is clear to fme that I didn't do enough research before getting into this. I thought my experience with putting custom roms on my galaxy S (a phone I really disliked) would give me the appropriate background. Clearly I was wrong! I'm a little unsure how to flash AOKP through TWRP when AOKP is not on my SD card. In fact, when I look at the SD card in TWRP, the only file on it is "TWRP."
I think I need to flash TWRP 2.3.0 (rather than the 2.2.2.0 I have), because it supports ADB Sideload (talked about here on their site which I can't yet link to). Can I do that through the Android SDK like I have been doing? I don't need to do anything to the TWRP 2.2.2.0 before trying to flash 2.3.0 do I? It seems if I do that, I could send AOKP to my phone through adb when it is in recovery.
And just for my better understanding, what is different about flashing it in TWRP and then flashing the boot.img in fastboot?
Thanks again!
Click to expand...
Click to collapse
Just like the post above mine says, you have to adb push the file onto the sd card. I'm not to familiar with TWRP (using it actually got me into a bit of a dilemma) so I only know the process for CWM. If TWRP is anything like CWM then you have to be in recovery to adb push and have sdcard and system set to "unmont". It's pretty easy and there's a couple threads explaining how to do it. The command basically is :: adb push romname.zip /sdcard/romname.zip:: Note the space before "/sdcard" I'dpn't know if this ill help you or if you've solved your problem already but this is just my 2 cents, good luck!
Sorry for my late reply; I was rushed to the ER last night in excruciating pain. Looks like I'll be dealing with a kidney stone over the next few days.
So far, I have tried to push AOKP through fastboot. ADB says "no devices found" and when I type adb devices, I get "List of devices attached" and nothing under it. However, when I type fastboot devices, I do get a device ID. As of now, I am downloading the TWRP 2.3 recovery and will try to sideload with adb with that.
Update:
I was able to successfully install TWRP 2.3 and adb sideload the AOKP zip file. The phone then went back into a reboot loop, and I was able to get into recovery to install the .zip. The phone then rebooted, showed the HTC with red text screen very briefly, went to black, showed the HTC with red text screen again, went black, and now the aokp boot animation is repeating over and over. It has been doing so for about 5-7 minutes. I haven't yet installed gapps as mentioned in the AOKP post (I'm honestly not even sure what that is). Where should I go from here?
As a side note, the phone is plugged into power though the LED is not lighting up. It was at 98% when I flashed the .zip, but I obviously don't want it to die on me. Should I turn the phone off or is it still charging?
Veritas327 said:
And just for my better understanding, what is different about flashing it in TWRP and then flashing the boot.img in fastboot?
Click to expand...
Click to collapse
The newer hboot versions (1.13 and up) don't let you flash boot images in recovery, even if it reports success.
So there is technically no difference, except fastboot always works and recovery depends on hboot version.
Did you fastboot flash the boot image that comes with your rom?
-Jobo
Edit to add: So it seems that following the recipe in your post #1 did in fact make your sdcard mountable again, or did you do something else as well for that?
Fixed!
I ended up flashing the boot.img with fastboot and then going into recovery, factory resetting and then re-installing the rom (and gapps which I now know stands for google apps). I'll be playing around with the ROM but at least I have a working phone again!
I think, in the end, it came down to my sd card not being mounted and my lack of knowledge about how to fix it.
RECOVERY IMAGE for SU760 ICS leak build for P920
This is all based on wkpark's thread here but focused only for p920.
ClockWorkMod(6.0.1.5) and TWRP(2.2.2.1) images as flashable images, to be used after you installed WKPark's alternate bootloader using his root signature. then we get full recovery back working on top of ICS.
Instructions on how to install the recovery.
Click to expand...
Click to collapse
Download wkparks fastboot loader from here
and extract contents into a temp folder.
1a. follow his instructions on how to install device drivers then goto step 2 or
1b.
remove battery, attach usbcable between pc and mobile.
Install the omap4430 driver, when you see a device appearing in "devicemanager" named omap4430,
rightclick on it and install driver from the 7z download and look in folder usb_drv_windows for the device driver.
remember to be fast to rightclick as it wil disappear and re-appear often until driver is installed.
1c. pc will find and install driver at next mobile restart (which is some seconds after.
Download the modified x-loader.bin,u-boot.bin,boot.img from this post and extract content into the temp folder from step1 and put files into the files directory found there.
extract attached p920-2-twrp.zip to the files folder you find in your files directory in the temp folder
extract attached p920-3-cwm.zip to the files folder you find in your files directory in the temp folder
remove battery and disconnect usb cable from mobile.
enter the temp you extracted to at step1, and run start_fastboot and select "2" in the menu shown in the commandline console.
attach usb cable
wait for the "start_fastboot to show alot of details and show booting 2ndboot.
attach battery when the 2ndboot information shows
fastboot v0.5 should be shown with a grey LG logo on your mobile now. , if not, go back and follow steps again.
at this stage, it can happen that "fastboot" driver for "LG Cosmo" device is installing but cannot find a driver, so you need to update driver through device manager, and point to the drivers, where the omap4430 driver was located too and update it.
Now its time to flash to new files run the 3 commands (one by one, do not try to copy/paste all 3 lines) shown just below as shown.
execute: fastboot flash x-loader files\x-loader.bin
execute: fastboot flash u-boot files\u-boot.bin
execute: fastboot flash boot files\boot.img
Lastly time to flash your recovery,
execute: fastboot flash recovery files\cwm.img
or
execute: fastboot flash recovery files\twrp.img
you cannot flash both images, as its not possible to have both recoveries installed.
11-nov-2012 - BOOTING INTO RECOVERY
Click to expand...
Click to collapse
You can always boot into recovery by holding 3D-BUTTON + VOL-UP down while pressing power-button to turn on mobile (without any cables attached to pc or power).
NOTES:
Click to expand...
Click to collapse
- If you do happen to get a bootloop it has been mentioned now, that it can happen if you copy/paster fastboot commands into the commandline shell.
these steps do NOT change anything of your system or data. it is only the bootloaders and boot.img/recovery.img which will change for the ICS build.
- both recoveries got USB mount storage issues, you will have to transfer files to sdcard or internal memory through windows.
- IMPORTANT: do not try and restore boot.img partition (before this install) from your ICS backups, it will cause the mobile not to boot.
and you will have to do the fastboot steps flashing this boot.img again. (it is caused by the signature is no longer a match)
THANKS TO:
Click to expand...
Click to collapse
wkpark - for his incredible work on getting us a custom uboot (still signed but a big help) - we await the unsigned boot
milaq - for the initial work on recoveries for our devices and cwm/twrp is used as base in these 2 images attached.
xbsall - the original release of ICS for p920/su760 edition.
A FEW STATEMENTS - CONFIRMING IT WORKS:
Click to expand...
Click to collapse
GlossGhost said:
I just installed it and it works as it should.
Click to expand...
Click to collapse
lemach said:
I have installed it on w7 64 bits and no problems. also i have installed rom manager and i can restart into recovery through rom manager o through app like quickboot.
Click to expand...
Click to collapse
Here is an alternative:
- download p920-1.zip and unpack to a temp directory.
- download usb_drv_windows.zip and install the driver. This is done when you see "omap4430" appear for a few seconds in device manager, when you attach phone to pc using usb without battery inserted.
- when driver is installed, install one of the recoveries attached to post #1 and unpack to the temp directory too, and finally run "runme.bat" from the temp directory you unpacked. and follow guideline here.
- when you see the commandline information "wait 5 seconds", you re-insert the battery.
- When "fastboot v0.5" shows in the optimus 3D display, you might need to install the fastboot driver(device: LG Cosmo) as well also located in the same zip above where OMAP4430 is found.
- If you do not get the "fastboot v0.5" in the phone display, something went wrong. and you might need to double check that your device manager in windows also shows the "OMAP4430 FastBoot USB device"
Never mind, wainting for a fix. Thanks
sorry guys, my guide works fine and so does the TWRP image and getting into it. But problem is, it seems original recovery does a trick to reset the flag "booting into recovery". So problem now is that it keeps booting into recovery and it cannot boot normally if you get TWRP started once.
I flashed back the original recovery for now and it works fine, when i sign that image with the new signature as well. but not worth much
booting original recovery once and the flag is reset and normal boot is possible.
Ill dig into this and report back and upload a working image, when i figured out the workaround this sad behaviour.
First, thanks for the tutorial and for your work. I wanted to know if this tutorial could be installed boot.img compiled by myself.
Google Translator
Enviado desde TheDarkRoom
adri_360 said:
First, thanks for the tutorial and for your work. I wanted to know if this tutorial could be installed boot.img compiled by myself.
Click to expand...
Click to collapse
yes, we can make custom boot.img as well with the solution he made. scripts and solution is posted in same thread mentioned in step1. i used it to create the recovery.img, but same goes for boot.img.
I hope u can find the solution for this. For some people like me, after we flash the bin, fls, root the device and use twrp. It just wont boot to recovery. So i hope this would work. But thanks again to xbsall for bringing ics to our device. At least now im on ics. Is there anyway i can use original recovery? So u can make a backup and restore if i need to reflash the ics bin again?
Thanks
Sent from my GT-P7500 using xda app-developers app
and it is working!!!!!
Finally got the continous reboot to recovery fixed!!!!
The images are bootable and do only reboot once into the recovery now.
the fix was to use some of the original binaries in the recovery so that mounts and binaries were started once.
So its all ok now.
I have also compiled a new CWM v6.0.1.5 from Recovery Builder clockworkmod, so its using latest release here, but it is not tested yet for full functionality.
This is nice. Thanks.
Sent from my LG-P920 using xda app-developers app
Thank you very much!! now it is late for me, but tomorrow i will follow your guide.
HELL YEAH! haha
HUGE THANKS, MAN!!! :victory: I was just about to flash the whole ROM again, just to make the TWRP work again :crying:
Im goin to start downloading and following the guide in a few min's.
I'll report as soon as im done with it :good:
-TMP
---------- Post added at 11:37 PM ---------- Previous post was at 10:50 PM ----------
ok.. im stuck @ 11.
"waiting for device"
it just wont start flashing. so i went to device manager and theres this new "connection" called LG Cosmo
and it says that the drivers for LG Cosmo are not installed.. what to do?
TMProduct1onZ said:
ok.. im stuck @ 11.
"waiting for device"
Click to expand...
Click to collapse
im stuck on highways, but where, might sometime be a good question if you want to avoid it
you cannot get much help unless you give more, so that kinda ends here.
but it might just be that when the OMAP4430 driver is installed and it loads fastboot v0.5 menu, it could be that the "fastboot" driver also needs to be updated.
check your device manager and find any new android device, and refer to the drivers you got with the step1 package or from my post#2 (i believe it could be your LG Cosmo device)
hmm
Dexter_nlb said:
im stuck on highways, but where, might sometime be a good question if you want to avoid it
you cannot get much help unless you give more, so that kinda ends here.
but it might just be that when the OMAP4430 driver is installed and it loads fastboot v0.5 menu, it could be that the "fastboot" driver also needs to be updated.
check your device manager and find any new android device, and refer to the drivers you got with the step1 package or from my post#2 (i believe it could be your LG Cosmo device)
Click to expand...
Click to collapse
lol ive told you where exactly i stuck :/
ok.. im stuck @ 11.
"waiting for device"
it just wont start flashing. so i went to device manager and theres this new "connection" called LG Cosmo
and it says that the drivers for LG Cosmo are not installed.. what to do?
Click to expand...
Click to collapse
So...
ive installed the LG COSMO drivers and it flashed.
and here's what happend:
-rom manager installed, reboot recovery
-bootloop
-had to flash XBSA404 again :/
-tryed again, same (bootloop)
-gived up
so at the end i had to do exactly that what ive tryed to avoid lol
but one good thing happend tho': Dualclock is gone :good:
now ive installed p940 recovery/TWRP again and it works...
Dont know if its only me
TMProduct1onZ said:
Dont know if its only me
Click to expand...
Click to collapse
you are not alone, its all those that do not understand the installation and wkpark's guide on using his tool. it is not that simple as just running an app. if drivers fail to install or you install the wrong driver, you never get fastboot opened, and if you never see fastboot menu on the phone when the tool starts and you insert battery as his guide says many things goes wrong.
but the instructions cannot be much more simple as they are, its 2 drivers its some steps in a command line to execute and thats pretty much it.
I will try it asap. I could go into fastboot mode last time so finger crossed. For those u have some problem going to fasboot mode try search the how to recover ur device to gb from xbsall. It works for me
Sent from my GT-P7500 using xda app-developers app
Dexter_nlb said:
you are not alone, its all those that do not understand the installation and wkpark's guide on using his tool. it is not that simple as just running an app. if drivers fail to install or you install the wrong driver, you never get fastboot opened, and if you never see fastboot menu on the phone when the tool starts and you insert battery as his guide says many things goes wrong.
but the instructions cannot be much more simple as they are, its 2 drivers its some steps in a command line to execute and thats pretty much it.
Click to expand...
Click to collapse
Hmm idk... maybe i really did something wrong but im sure it was all ok i did see the fastboot menu and i executed everything.
However ill do a backup and then try again later today
Sent from my P920 using ICS 4.0.4 by XBSA
Now its time to flash to new files run the 3 commands shown just below as shown.
fastboot flash x-loader files\x-loader.bin
fastboot flash u-boot files\u-boot.bin
fastboot flash boot files\boot.img
I could start fastboot with the grey logo and fastboot v0.5 on the top left of my device
when i type fastboot flash x-loader files\x-loader.bin
it says waiting for device
after i waited for 2-3 minutes the device just boot normally.
what did i do wrong?
thanks
edit:
i flashed all the command sucessfully
install rom manager
reboot into recovery and it boot loop
it only shows twrp logo and then reboot to lg logo
what should i do?
HOW TO INSTALL RECOVERY IMAGE WITH SUCCESS
I just installed it and it works as it should.
Here's how to do it.
1. Boot into fastboot
2. After installing drivers for OMAP and LG Cosmo, start the shell.
3. Execute lines one by one:
fastboot flash x-loader files\x-loader.bin
then
fastboot flash u-boot files\u-boot.bin
and
fastboot flash boot files\boot.img
EXECUTING THEM ALL WILL LEAD IN A BOOTLOOP, DONT WORRY ITS FINE
4. Boot into fastboot and flash them again.
fastboot flash x-loader files\x-loader.bin
then
fastboot flash u-boot files\u-boot.bin
and
fastboot flash boot files\boot.img
5. Flash recovery image.
fastboot flash recovery files\cwm.img
or
fastboot flash recovery files\twrp.img
After boot, install ROM Manager and reboot into recovery.
If you still have problems, go back and do everything right.
GlossGhost said:
HOW TO INSTALL RECOVERY IMAGE WITH SUCCESS
I just installed it and it works as it should.
Here's how to do it.
Click to expand...
Click to collapse
thanks, hope your assistance above will help those still failing, because when it works, its actually rather nice to have working.
i will also try to improve the documentation executing the lines now.
awi05 said:
what did i do wrong?
Click to expand...
Click to collapse
try and flash all the "fastboot" files as written once more, and maybe for testing purposes, try the cwm.img instead of twrp image. you can also switch to twrp when you see you got it working. i do not flash all files switching, only cwm or twrp images needs to be flashed.
When the bootloader is updated, we can actually flash boot and recovery images from a shell prompt now. as long as the image is with signature. but fastboot will just be a brick recovery step when you first got it working.
Hi XDA,
I am a complete noob, and this is my first time posting, so bear with me.
Some time ago I rooted and unlocked my TF300 with SuperSu. Recently I wanted to upgrade to 4.4 kitkat. However, my Tablet was stuck at Andriod 4.1 because of the the unlock.
I went to manually update my TF via the Asus website. I installed the 10.6.1.8 using my TWRP 2.5, and Oem 4.1 OS. Installation worked just fine. After install, I booted up and I had 4.2 with everything working correctly.
Next step was to install TWRP 2.7.0.1. I reset my TF and went into RCK to see something went wrong when updating.
My TWRP will not load, and I get the Android on his back with the red triangle when I try to enter RCK.
Thanks in advance!!
I managed to install 10.6.1.27, but it did not change anything with my boot loader.
I downloaded motochopper, but that didn't seem to work, just told me my abt was out of date. SuperSu isn't working now either, "No Binary, There is a problem."
How do I install TWRP 2.7 with no boot loader? Please help.
TallMilk said:
I managed to install 10.6.1.27, but it did not change anything with my boot loader.
I downloaded motochopper, but that didn't seem to work, just told me my abt was out of date. SuperSu isn't working now either, "No Binary, There is a problem."
How do I install TWRP 2.7 with no boot loader? Please help.
Click to expand...
Click to collapse
Most people just install TWRP via fastboot like
Code:
fastboot -i 0x0B05 flash recovery twrp.blob
You could try using other root methods, like Framaroot or Kingo. I think Kingo was reported to work on the latest stock version.
cmendonc2 said:
Most people just install TWRP via fastboot like
Code:
fastboot -i 0x0B05 flash recovery twrp.blob
You could try using other root methods, like Framaroot or Kingo. I think Kingo was reported to work on the latest stock version.
Click to expand...
Click to collapse
I will look into that, but I am pretty sure I was already rooted, unless losing my boot loader means I am no longer rooted.
Another thing, I can't find a twrp.blob for 2.7, just a zip. I have one for 2.5, but that is useless because I already have 4.2. I also have not been able to find a working link to fastboot.
If anyone could give me a link to the fastboot or a link to a tutorial, that would be amazing. I have done my research, but all the lingo and different methods can be mind bending.
Thanks
TallMilk said:
I will look into that, but I am pretty sure I was already rooted, unless losing my boot loader means I am no longer rooted.
Another thing, I can't find a twrp.blob for 2.7, just a zip. I have one for 2.5, but that is useless because I already have 4.2. I also have not been able to find a working link to fastboot.
If anyone could give me a link to the fastboot or a link to a tutorial, that would be amazing. I have done my research, but all the lingo and different methods can be mind bending.
Thanks
Click to expand...
Click to collapse
You can get the img (which substitutes as a blob) from extracting it from the TWRP 2.7 zip file.
1) You will need ADB and fastboot for this: http://forum.xda-developers.com/showthread.php?p=42407269. I would suggest keeping the tablet at least at 50% battery.
2) Install Naked Drivers. This may be optional for you. If you can proceed to the next step without, you won't need it.
3) Enter fastboot by rebooting and holding down the power button. TF300 enters fastboot automatically since this is 4.2 BL.
4) Next we need to enter a command. In side the ADB folder, hold shift and right click. Then select Open command window here.
first check to make sure the device is connected:
Code:
fastboot devices
The device serial number should be listed.
enter command:
Code:
fastboot flash recovery twrp.img -i 0x0b05
Blue bar on device will fill. Be patient.
5) Reboot the Device back into Android. This is an important step.
6.) Go back into TWRP and install what you want.
You are amazing. I will give it a try tonight and report back!
cmendonc2 said:
You can get the img (which substitutes as a blob) from extracting it from the TWRP 2.7 zip file.
1) You will need ADB and fastboot for this: http://forum.xda-developers.com/showthread.php?p=42407269. I would suggest keeping the tablet at least at 50% battery.
2) Install Naked Drivers. This may be optional for you. If you can proceed to the next step without, you won't need it.
3) Enter fastboot by rebooting and holding down the power button. TF300 enters fastboot automatically since this is 4.2 BL.
4) Next we need to enter a command. In side the ADB folder, hold shift and right click. Then select Open command window here.
first check to make sure the device is connected:
Code:
fastboot devices
The device serial number should be listed.
enter command:
Code:
fastboot flash recovery twrp.img -i 0x0b05
Blue bar on device will fill. Be patient.
5) Reboot the Device back into Android. This is an important step.
6.) Go back into TWRP and install what you want.
Click to expand...
Click to collapse
Installed adb fastboot. However, my device does not automatically go into fastboot, I still have to hold down the volume key.
Once I am in fastboot usb (with the 3 icons), I fastboot successfully and get the serial number, then when I type the 'fastboot flash recovery twrp.img -i 0x0b05' command I get this error: cannot load 'twrp.img' : No error
I am attemping to use the 2.7.0.1 twrp from the 4.4.2 page. I have extracted the recovery.img (tried renaming to twrp and left it the same) and placed it in the root of both my external and internal sd.
I have now tried it with .zips .img .blob and I receive the same error everytime. Not sure what I am doing wrong now.
TallMilk said:
Installed adb fastboot. However, my device does not automatically go into fastboot, I still have to hold down the volume key.
Once I am in fastboot usb (with the 3 icons), I fastboot successfully and get the serial number, then when I type the 'fastboot flash recovery twrp.img -i 0x0b05' command I get this error: cannot load 'twrp.img' : No error
I am attemping to use the 2.7.0.1 twrp from the 4.4.2 page. I have extracted the recovery.img (tried renaming to twrp and left it the same) and placed it in the root of both my external and internal sd.
I have now tried it with .zips .img .blob and I receive the same error everytime. Not sure what I am doing wrong now.
Click to expand...
Click to collapse
Put the twrp.img into your ADB folder, where you installed it. Then run the next command.
cmendonc2 said:
Put the twrp.img into your ADB folder, where you installed it. Then run the next command.
Click to expand...
Click to collapse
Awesome! Worked like a charm. twrp 2.7.0.1 installed perfectly.
Then I tried to flash the cyanogenmod. Said it installed fine, but it just gets stuck on the loading screen...
I am trying to do exactly what TallMilk is doing...put Cyanogenmod on my tablet. It is my understanding that I have to unlock my bootloader though? Which I have tried doing a million different ways with the Asus Unlock tool which always gives me an error.
If I follow the instructions posted above I will be able to flash Cyanogenmod without unlocking my bootloader?
SilentSpartan said:
I am trying to do exactly what TallMilk is doing...put Cyanogenmod on my tablet. It is my understanding that I have to unlock my bootloader though? Which I have tried doing a million different ways with the Asus Unlock tool which always gives me an error.
If I follow the instructions posted above I will be able to flash Cyanogenmod without unlocking my bootloader?
Click to expand...
Click to collapse
Finally got it to work. I had to do a wipe first, read about old roms interfering with new installations.
SilentSpartan, I used SuperSU last year to root and unlock my tablet when it was still a 4.0 android to flash to 4.1. This recent update was from 2.5 TWRP on a rooted device running 4.2. When I installed 4.2, it blew away my TWRP, and I had to flash the new TWRP 2.7.0.1.
That flash from OEM fastboot to TWRP 2.7.0.1 is what I needed help with.
TallMilk said:
Finally got it to work. I had to do a wipe first, read about old roms interfering with new installations.
SilentSpartan, I used SuperSU last year to root and unlock my tablet when it was still a 4.0 android to flash to 4.1. This recent update was from 2.5 TWRP on a rooted device running 4.2. When I installed 4.2, it blew away my TWRP, and I had to flash the new TWRP 2.7.0.1.
That flash from OEM fastboot to TWRP 2.7.0.1 is what I needed help with.
Click to expand...
Click to collapse
Damn, so I'm screwed. Why does Asus have to such so much...? You can no longer unlock afaik.
SilentSpartan said:
I am trying to do exactly what TallMilk is doing...put Cyanogenmod on my tablet. It is my understanding that I have to unlock my bootloader though? Which I have tried doing a million different ways with the Asus Unlock tool which always gives me an error.
If I follow the instructions posted above I will be able to flash Cyanogenmod without unlocking my bootloader?
Click to expand...
Click to collapse
You're going to have to unlock no matter what. Did you try both v7 and v8 of the unlocker and calling Asus Support to tell them to put your serial number back into the database (get a manager)?
cmendonc2 said:
You're going to have to unlock no matter what. Did you try both v7 and v8 of the unlocker and calling Asus Support to tell them to put your serial number back into the database (get a manager)?
Click to expand...
Click to collapse
I've tried every firmware and unlock tool combination. Nothing works. I sent them an email a day ago. Depending on there response, maybe I'll try calling. I'm so fed up with this tablet, I'm about to throw it out my window. $400 POS. :good:
SilentSpartan said:
I've tried every firmware and unlock tool combination. Nothing works. I sent them an email a day ago. Depending on there response, maybe I'll try calling. I'm so fed up with this tablet, I'm about to throw it out my window. $400 POS. :good:
Click to expand...
Click to collapse
Did you ever get your tablet fixed? I am having some problems myself after a miserable m9 update.
I tried to flash a custom rom (KatKiss), and it seems that I did something wrong along the way because the tablet is stuck in a bootloop.
So I rebooted my tablet and access the bootloader ("fastboot devices" recognize my device) and try to go to the recovery (with the TWRP splash screen, "adb devices" recognize my device). Unfortunately after 20 seconds on the splash screen, the tablet reboots (tries to load my katkiss android but bootloop everytime).
Bootloader : 10.6.1.14.10
TWRP : 3.1.1.0
Since the fastboot recognize my device while in bootloader, I think that I should try to flash twrp since it seems to be corrupted somehow.
Every time I flashed a rom nothing went wrong but now that I have a problem I don't want to worsen it and would like some help on the issue.
Did you flash the rom in your current TWRP?
Something is off... Did you possibly flash the TF201 rom version??
Whatever you do - do not use Wipe Data from the bootloader!!
Reflash TWRP, format data, then reflash the rom
And report in more detail what you did
Sent from my Nexus 5X using Tapatalk
Thank you for the fast reply!
I did flash the rom with my current TWRP and only downloaded the rom version for the TF700. Below is what I tried from your suggestion:
I check that my device is recognized:
fastboot device
So I tried flashing TWRP:
fastboot flash recovery twrp-3.1.1-0-tf700t
After it succeeded, I reboot the tablet:
fastboot reboot
And as a result... nothing changes, I don't know if I should try with older version of TWRP. Seems like I only have access to the tablet with the fastboot.
That is very strange indeed. Yes, try a 3.0.2 version of TWRP and see if that works.
If not, I would flash the Asus stock blob in fastboot and start from scratch....
Sent from my TF700T using Tapatalk
Kromlech said:
And as a result... nothing changes, I don't know if I should try with older version of TWRP. Seems like I only have access to the tablet with the fastboot.
Click to expand...
Click to collapse
Not sure if this will help but I had a reboot problem with trying to load into TWRP. I posted my solution into a different thread but will toss it out here..
I just had this problem with a Transformer 201Prime. The cycle went something like this..
Power on.... get ASUS logo in middle, Tegra3 logo on lower right, and bootloader unlocked in upper left....
then a buzz... then reboot.....
So I would try the power button and hold the volume down... that got me into the bootloader but when I hit the volume up button it would give me the TWRP logo... then buzz and reboot...
After much monkeying around... I realized I would have to re install everything. Fortunately I had the original NVFLASH bloob files backed up so I was able to get into the NVFLASH commands.
Here is a great tutorial, it is for the 201 so be sure to download the correct files but the steps are basically the same.
https://forum.xda-developers.com/tra...prime-t3486237
The other problems is I had to download a bloob tool to 'unpack' the necessary .bin and .ebt files that are mentioned in the commands... I used the following link to download the tool.
https://github.com/AndroidRoot/BlobTools
I hope this helps shake loose a few answers.
Once I was able to get a working recovery I could flash an updated ROM. (KatKiss is my current favorite)
I tried to flash version 3.0.2 of TWRP and the problem is still the same.
@Unidave199 the link you put in your post points to a post that doesn't seems to exist anymore, has it been moved?
@berndblb how do I do for flashing a rom with the fastboot? any stock rom to recommend?
double post
Kromlech said:
I tried to flash version 3.0.2 of TWRP and the problem is still the same.
@Unidave199 the link you put in your post points to a post that doesn't seems to exist anymore, has it been moved?
@berndblb how do I do for flashing a rom with the fastboot? any stock rom to recommend?
Click to expand...
Click to collapse
Unidave's link would only help you if you generated your device specific nvflash blobs when the tablet was still functioning. Did you:
flash a specifically modded recovery - flash the moddded bootloader, use wheelie to generate and save your blobs, return everything to factory specs?
I highly doubt it since you would have mentioned...
To flash the stock blob in fastboot you download the Asus firmware from here: https://www.asus.com/my/support/Download/28/1/0/11/29/8/
Extract the zip twice until you see a blob and a meta-inf file.
Move the blob into your fastboot folder, discard the rest of the file
Issue these commands one by one, letting each one finish before starting the next. Some will finish quick, others may take up to 3 minutes:
Code:
fastboot erase system
fastboot erase boot
fastboot erase recovery
fastboot erase misc
fastboot erase cache
fastboot erase userdata
fastboot flash system blob
fastboot reboot
The first boot will take a while, but that should put you back on a stock JB 4.2 system.
Trash all the files you used in your last attempt and redownload the rom, gapps and supersu
Fastboot flash TWRP
Reboot
Format /data in TWRP (this will take up to 1 hour - let it finish!!), then convert /data to f2fs
Flash the rom, gapps, supersu
If you flash Nougatella remember that you have to turn on wifi right after the language selection during setup or Google framework will crash.
Spend the end of the day doing it, but it worked flawlessly! Thanks a lot @berndblb, now I can use my tablet again!
Kromlech said:
I tried to flash version 3.0.2 of TWRP and the problem is still the same.
@Unidave199 the link you put in your post points to a post that doesn't seems to exist anymore, has it been moved?
@berndblb how do I do for flashing a rom with the fastboot? any stock rom to recommend?
Click to expand...
Click to collapse
My apologies for the problem with my link, looks like you resolved it, but wanted to post a correct working link to take someone else into the full conversation and context...
https://forum.xda-developers.com/showpost.php?p=71150385
berndblb said:
To flash the stock blob in fastboot you download the Asus firmware from here: https://www.asus.com/support/Download/28/1/0/11/fq2B3oq64av1O95/8/
Click to expand...
Click to collapse
Broken link ? that post isn't very old, either. ??
berndblb said:
Did you flash the rom in your current TWRP?
Something is off... Did you possibly flash the TF201 rom version??
Whatever you do - do not use Wipe Data from the bootloader!!
Reflash TWRP, format data, then reflash the rom
And report in more detail what you did
Click to expand...
Click to collapse
I did wipe data from bootloader, now I can't go to bootloader. How to revive my tf700t?
Please help
Thanks
ketulharini said:
I did wipe data from bootloader, now I can't go to bootloader. How to revive my tf700t?
Please help
Thanks
Click to expand...
Click to collapse
You'll need to refer to post #8. However, the link to the tf700 stock blob is broken. You'll have to search Google for one. They're out there, but it does require digging .Make sure the one you get is for the proper SKU of your tablet (US, Worldwide, JP, etc.). I completed the process myself maybe a month ago. Good luck!
monogwai said:
You'll need to refer to post #8. However, the link to the tf700 stock blob is broken. You'll have to search Google for one. They're out there, but it does require digging .Make sure the one you get is for the proper SKU of your tablet (US, Worldwide, JP, etc.). I completed the process myself maybe a month ago. Good luck!
Click to expand...
Click to collapse
I got the stock blob ww version.
Just tab doesn't stay on fastboot mode keeps rebooting.
Don't know how to do it.
Is it possible to get stable fastboot screen some how? Or just flash the bootloader to get fastboot working.
May be this noob question but I don't know how to do.
Thanks
ketulharini said:
I got the stock blob ww version.
Just tab doesn't stay on fastboot mode keeps rebooting.
Don't know how to do it.
Is it possible to get stable fastboot screen some how? Or just flash the bootloader to get fastboot working.
May be this noob question but I don't know how to do.
Thanks
Click to expand...
Click to collapse
There is one more piece to the puzzle- hold short while I dig it up.
Here it is: http://www.transformerforums.com/forum/transformer-pad-infinity-tf700-tegra-3-development/46302-guide-help-my-transformer-tf700-boots-only-recovery.html
Do be *very* careful. Read thrice, do it once. Especially if you're feeling noob-y.
monogwai said:
There is one more piece to the puzzle- hold short while I dig it up.
Here it is: http://www.transformerforums.com/fo...my-transformer-tf700-boots-only-recovery.html
Do be *very* careful. Read thrice, do it once. Especially if you're feeling noob-y.
Click to expand...
Click to collapse
Thanks for this information.
One more question,
My tab is keep bootlooping neither it stays on twrp nor bootloader.
It has blue screen of recovery that is twrp after 5 to 10 seconds it boots again.
Is this enough time to execute the commands while it is on blue screen?
Thanks
ketulharini said:
Thanks for this information.
One more question,
My tab is keep bootlooping neither it stays on twrp nor bootloader.
It has blue screen of recovery that is twrp after 5 to 10 seconds it boots again.
Is this enough time to execute the commands while it is on blue screen?
Thanks
Click to expand...
Click to collapse
Well, that depends on several things. What I did was write a short little DOS batch file to process all the fastboot commands. So, with your batch file ready, open your command prompt (change directory to your adb/fastboot directory if it's not set in system's 'path=' environment variable) and have the batch command typed in, ready to hit enter. Tether to pc via USB, proceed to boot to adb. The second you hear windows make the USB notification sound, slap that enter key. It should just process and reset the tab and get you out of TWRP bootloop. Which is just step one.
If you aren't familiar with writing bat files for DOS, let me know.
monogwai said:
Well, that depends on several things. What I did was write a short little DOS batch file to process all the fastboot commands. So, with your batch file ready, open your command prompt (change directory to your adb/fastboot directory if it's not set in system's 'path=' environment variable) and have the batch command typed in, ready to hit enter. Tether to pc via USB, proceed to boot to adb. The second you hear windows make the USB notification sound, slap that enter key. It should just process and reset the tab and get you out of TWRP bootloop. Which is just step one.
If you aren't familiar with writing bat files for DOS, let me know.
Click to expand...
Click to collapse
You mean a batch file with the adb commands right? Once he can boot into fastboot he has all the time in the world to run the commands for the buster99 (description in post #8). Depending on what situation he came from before, it might be a good idea to start all fresh...
The tricky thing are the adb push bootit.ko and the insmod command. Those have to be timed just right to get executed, so a batch file might come in handy. Both commands only take a second or two to execute, so your window of 5 seconds could work. Maybe not in the same session, but they should work.
If the insmod command does not kick the tablet into the bootloader, there are 2 possible reasoons:
adb push bootit.ko did not work
the insmod command did not work
To find out if the file push worked you could add a simple list command for the contents of /sdcard/. Again - tricky, I know since you still are working with the 5 sec window, but that's what you got to work with...
That would look something like in the attached picture. So after pushing bootit.ko you issue:
Code:
adb shell ls /sdcard/
Try it with the batch file, try it with single commands... Don't give up. As long as you have any kind of adb access you should be able to solve it.
Good luck!
berndblb said:
You mean a batch file with the adb commands right?
Click to expand...
Click to collapse
Yeah.
berndblb said:
Once he can boot into fastboot he has all the time in the world to run the commands for the buster99 (description in post #8).
Click to expand...
Click to collapse
Again, mistake in my terminology. What I meant to say is, batch commands for the process involving the Bootit.ko- the adb portion.
Thanks for clearing that up.
@ketulharini
Anyhow, I was unable to get the process to take without having automated *every last step* of the process. Literally open the cmd window, have the command for your batch file typed in ready to go, and plug in. Hear the noise from windows and slap enter asap. That's the only way I could get it in time, and I'm a ridiculously fast typist.
monogwai said:
Yeah.
Again, mistake in my terminology. What I meant to say is, batch commands for the process involving the Bootit.ko- the adb portion.
Thanks for clearing that up.
@ketulharini
Anyhow, I was unable to get the process to take without having automated *every last step* of the process. Literally open the cmd window, have the command for your batch file typed in ready to go, and plug in. Hear the noise from windows and slap enter asap. That's the only way I could get it in time, and I'm a ridiculously fast typist.
Click to expand...
Click to collapse
Care to share the batch file?
I had a bit of a problem with CM and it kept saying trebuchet had stopped working. (This is after the phone had been running fine for a whole year with CM. Then the phone kept restarting and saying trebuchet had stopped working and it would constantly restart until it calmed down. I decided to install and alternative launcher but the problem didn't totally go.
Thereafter I decided to delete trebuchet from root and boom the phone never calmed down and kept restarting. Eventually I tried restoring factor settings and it says now that there's no OS.
I had TWRP installed before but now when I've tried to install the latest one, it doesn't show any files on the OTG. I've put twrp on the SD along with a rom as well but nothing shows at all.
Can someone help in simple terms?
emmpii said:
I had a bit of a problem with CM and it kept saying trebuchet had stopped working. (This is after the phone had been running fine for a whole year with CM. Then the phone kept restarting and saying trebuchet had stopped working and it would constantly restart until it calmed down. I decided to install and alternative launcher but the problem didn't totally go.
Thereafter I decided to delete trebuchet from root and boom the phone never calmed down and kept restarting. Eventually I tried restoring factor settings and it says now that there's no OS.
I had TWRP installed before but now when I've tried to install the latest one, it doesn't show any files on the OTG. I've put twrp on the SD along with a rom as well but nothing shows at all.
Can someone help in simple terms?
Click to expand...
Click to collapse
Use adb commands to flash TWRP (Put your TWRP image in the same folder on your pc as your adb and enter each command separately):
adb reboot bootloader
fastboot flash recovery twrp.img (latest version is 3.1.1-0-peregrine, remame it to twrp.img - if that doesn't work rename twrp to recovery.img and try that).
fastboot reboot
If that works, restore you last known good working backup or try re-installing your stock rom.
sdembiske said:
Use adb commands to flash TWRP (Put your TWRP image in the same folder on your pc as your adb and enter each command separately):
adb reboot bootloader
fastboot flash recovery twrp.img (latest version is 3.1.1-0-peregrine, remame it to twrp.img - if that doesn't work rename twrp to recovery.img and try that).
fastboot reboot
If that works, restore you last known good working backup or try re-installing your stock rom.
Click to expand...
Click to collapse
I've installed fastboot onto my PC. Now i'm trying the adb commands but my phone isn't showing up
Tried a new cable.. so far it's started to recognise. I'll update this if theres news.
*adb command doesn't work... says no devices. Fastboot seems to work
ive managed to get the latest twrp on.. now I cant seem to adb sideload the rom nor does it show via otg.. ADB sideload disconnects and says invalid zip file
emmpii said:
I've installed fastboot onto my PC. Now i'm trying the adb commands but my phone isn't showing up
Tried a new cable.. so far it's started to recognise. I'll update this if theres news.
*adb command doesn't work... says no devices. Fastboot seems to work
Click to expand...
Click to collapse
Install or re-install your Motorola Device Manager on your pc from this link: https://mobilesupport.lenovo.com/us/en/solution/MS88481
Check in your pc Device Manager to see if your device is connected and recognized properly when you plug in the USB cable.
In the folder where your adb and fastboot files are, open a command prompt and enter adb devices to see if the phone is recognized now in adb. If it is, proceed as suggested earlier.
sdembiske said:
Install or re-install your Motorola Device Manager on your pc from this link: https://mobilesupport.lenovo.com/us/en/solution/MS88481
Check in your pc Device Manager to see if your device is connected and recognized properly when you plug in the USB cable.
In the folder where your adb and fastboot files are, open a command prompt and enter adb devices to see if the phone is recognized now in adb. If it is, proceed as suggested earlier.
Click to expand...
Click to collapse
shows up in device manager as android usb device, Still not showing on adb
I managed to get the device to finally track on with adb. It tracks fine now. However I can't seem to flash a rom on regardless of whether its OTG or sideload...
emmpii said:
shows up in device manager as android usb device, Still not showing on adb
Click to expand...
Click to collapse
Go to this link (https://forum.xda-developers.com/moto-g/4g-development/rom-stock-motorola-4g-lollipop-rom-t3142816) and download the correct untouched rom for your phone model and transfer it to your sd card or internal memory.
Then try this command: fastboot boot recovery.img or fastboot boot twrp.img
and follow the directions exactly in the op in that thread to flash the rom.
sdembiske said:
Try this command: fastboot boot recovery.img or fastboot boot twrp.img
Go to this link (https://forum.xda-developers.com/moto-g/4g-development/rom-stock-motorola-4g-lollipop-rom-t3142816) and download the correct untouched rom for your phone model and transfer it to your sd card or internal memory.
Then try this command: fastboot boot recovery.img or fastboot boot twrp.img
and follow the directions exactly in the op in that thread to flash the rom.
Click to expand...
Click to collapse
Absolutely no idea how but I managed to get one of the CM roms sideloaded and even though when i chose to reboot it said no OS. I've got it going, however I've forgotten to put gapps on so I'll try that now. Later on I'll try sideload stock rom or something and see how that goes. Thanks for the help so far! :good:
emmpii said:
Absolutely no idea how but I managed to get one of the CM roms sideloaded and even though when i chose to reboot it said no OS. I've got it going, however I've forgotten to put gapps on so I'll try that now. Later on I'll try sideload stock rom or something and see how that goes. Thanks for the help so far! :good:
Click to expand...
Click to collapse
The problem with CM roms is they're not really being updated anymore - just one of the problems I have with a lot of custom roms besides the bugs, etc., etc.
If you're hell bent on a custom rom, I would check out this one: [ROM][OFFICIAL][Peregrine][7.X] LineageOS 14.1 at https://forum.xda-developers.com/moto-g/4g-development/rom-cyanogenmod-14-0-t3469103
Lineage is the new go-to from CM. I personally would go back to stock first, however, to ensure everything is restored properly before installing it.
It's being updated regularly currently.
I just had a old CM rom downloaded from before hence I went to that lol. I'm trying lineage for now but I've also downloads the stock ROM. Whatever will keep the phone going