Related
hey guys,
my phone litteraly wont do anything. i f*ed up some fonts using type fresh, then tried to restore using the odin3 downloader. i accidentally closed it, and now my phone wont boot up/react to any buttons pressed. any help? thanks guys!
had the same problem. i cant figure out how to even get odin working, it says one click but when i hook up it to odin it gives me a message that still doesnt tell me ****. i had to send my phone back for a new one and told them i used easyroot on the market bc i didnt know what it was and it sounded cool but now i know not to ever do that again that it messd up my phone. Praying to god that they dont charge my for anything
You should still be able to enter bootloader mode by turning phone off and holding down up/down vol and pwr simultaneously until boot screen flashes then release power button only
it wont even do that
open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.
it wont do anything at all. it wont power on, show up in adb, anything... and stupid att wont do ANYTHING -_- oh well. any help would be appreciated!
Have any of you offering support to the OP actually had your phone in the described state? I've read a few posts where the phone is seemingly completely dead as the OP describes and no one says they've successfully recovered from that state. All I ever see is the same old button combinations/battery/usb shenanigans and statements of that should work and that the phone is unbrickable. I have personally seen a device that was behaving in such a manner and no combination of battery pulling, usb plugging, button holding, or tongue twisting would generate anything from the phone. The only thing the phone would do was get hot.
same here. Phone showed bright green screen...wasnt done with teh flash and said it was finished...now the nly thing I can get is power and hold the vlume up for some IRQ and hex stuff. I posted a questionthis morning but...serious. Vol up and down and any things else gives nothign but a black screen..battery out...back in anything..its torched.
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
when i plug it in, windows doesnt make any noises and doesnt recognize it, and when i use the "adb devices" command, nothing shows up.
daveshih said:
Have you tried getting into download mode via the sdk?
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Did you read the rest of the posts? The OP already stated several times that the phone does nothing. I realize that most people will say it does nothing or is "bricked" if it simply shows the "connect to computer" screen, but the OP has stated more than once that the phone shows nothing. Yes, everyone is trying to help, but simply repeating what has been said numerous times before doesn't help.
Has anyone actually recovered a phone that displays NOTHING? No logos, no recovery, no nothing.
Last night, i turned off the light in my room when i noticed a glowing from my desk. i walked over, and it turns out my captivate's screen was in fact on, it was just a faint black glow, and none of the power buttons would do anything. when i took the battery out, it shut off completely!
As I pointed out here
http://forum.xda-developers.com/showthread.php?t=757293
Im pretty sure it was my fault for not completely following instructions on the ext4 one click install root, settings.db etc so everyone needs to make sure if the dev says flash before..do it.
State of the phone was, it would not completely power on..therefor no usb drivers would load and Odin cannot see the phone and it can no longer flash..the only thing I could get it to do was show a screen with that text. I put in my post. I ordered it via letstalk.com so I sent it back and assuming they get the same result Ill have a new one hopefully by the end of the week. Im just glad I stil had my old iphone3 to slap my sim card in.
The odin one click flash thing..it just flaked right at the start it looked like..but I cant be sure because as soon as I saw a blue progress bar I stepped into the kitchen for abtou 30 sec..I came back and the screen was florescent green and Odin said it was done. I knew something was wrong as it was way too fast so I unplugged, removed the battery and set it back in...from there on out it would do nothing with the power button unless on a semi rare occasion if I hit the volume up button and power I got the IRQ stuff.
Annoying as I had a nandroid backup just before I started messing with it.
i just sent mine into samsung... back to mah ol trusty blackjack. gonna have to get used to supermario bros 3 instead of spyro....
ANYWAYS theyre sending me a new one!
uiskibum said:
open odin (use the stock one click version)
with the phone off (remove/reinsert the battery if need be) and not plugged in; hold vol. down and insert the usb cable (keep holding vol. down untill you see the download screen). this should put you into download mode and if you have the right drivers odin should recognize the phone.
I've stuffed my captivate on a few occasions and so far I have been able to use this method to get into download mode and fix it.
Click to expand...
Click to collapse
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...
ace518 said:
So, yes in same state as op... no nothing... couldn't get jack out of it. at all, none
what this post said worked.... not holding power button... nothign...
removed battery
plugged in battery
hold vol down
(still no response)
plug in usb cable and continue holding vol down.
it went to recovery mode
... no holding of power button, just vol down and plugged in USB... give it a shot man, let me know
EDIT: feel free to PM me if you want me to help walk you through it...
Click to expand...
Click to collapse
Hey thanks, but i already sent it to em... thank you everyone for your help!
Just a note... i said before hold vol down and plug in usb. I had it in a pretty bad state tonight. Played around. Same idea as before, but had to hold vol up and vol down. If i brick a few more times, i'll give a better guide. But this phone can DEFINITELY come back from a state where you can't even get it to power on. Figured any additional info on this would be good.
Hey, I got my transformer yesterday, and for some reason this is the 2nd time this has happened, fully charged battery, but the device won't power on. Attempted to plug into power but no dice. Held the power button for 30 seconds, nothing, held the power and volume up and nothing. Yesterday when this happened I plugged it into my computer (Windows) and held the power and up buttons and it turned on though it could have been windows detecting the drivers. Anyone else having this? Any suggestions? I haven't had a chance to test again and see if I can bring it back through that trick yet, but I will. Then I'll try a factory reset and see if it resolves the issue. I would hate it if this is a defective unit, that's for sure esp since they are so backordered. Outside of that I love the device.
naturefreak85 said:
Hey, I got my transformer yesterday, and for some reason this is the 2nd time this has happened, fully charged battery, but the device won't power on. Attempted to plug into power but no dice. Held the power button for 30 seconds, nothing, held the power and volume up and nothing. Yesterday when this happened I plugged it into my computer (Windows) and held the power and up buttons and it turned on though it could have been windows detecting the drivers. Anyone else having this? Any suggestions? I haven't had a chance to test again and see if I can bring it back through that trick yet, but I will. Then I'll try a factory reset and see if it resolves the issue. I would hate it if this is a defective unit, that's for sure esp since they are so backordered. Outside of that I love the device.
Click to expand...
Click to collapse
when your device isnt coming on, does your computer give you a usb notification? You could be putting it in apx mode on accident.
dcmtnbkr said:
when your device isnt coming on, does your computer give you a usb notification? You could be putting it in apx mode on accident.
Click to expand...
Click to collapse
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
try turning off screen lock.
naturefreak85 said:
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
Click to expand...
Click to collapse
I had that sometimes in the first day I had it, after that it hasn't happened. No factory reset, just make sure to do a hard shutdown (powerbutton 10 sec~) while it's booted and it should fix the issue.
seshmaru said:
I had that sometimes in the first day I had it, after that it hasn't happened. No factory reset, just make sure to do a hard shutdown (powerbutton 10 sec~) while it's booted and it should fix the issue.
Click to expand...
Click to collapse
Yea, it had happened once already, and again. I'll be testing today when I leave work, factory reset and see what happens. Should it continue, I'll go to the next step. I'm just not sure what it is. Interesting bug to say the least.
naturefreak85 said:
I will find out in a few. The thing is this has happened when I left the device unplugged and in sleep when driving to/from work. Yesterday plugging it back into the computer brought it to life. Nothing else did. Not sure what apx mode is even.
Sent from my MB860
EDIT: Ok, turns out it get stuck in some weird power mode. I plugged it into the computer with no resolution, when I held the power button for 10 seconds, then waited 5 and pressed it again, the device powered on. I suspect it might be an issue involving detecting WiFi access points when driving or something else. I'll Factory Restore and see what happens.
Click to expand...
Click to collapse
From the way you are describing getting it to work again, it sounds like you were in apx mode...
dcmtnbkr said:
From the way you are describing getting it to work again, it sounds like you were in apx mode...
Click to expand...
Click to collapse
I still don't really know what APX mode is, from the limited things I have seen about it, in order to get into such, the device has to be powered off first. As far as I can tell, my device isn't randomly powering itself off and automatically going into APX mode. This happens without me touching the device. When I did the power off and on today, it wasn't plugged into the computer at all. There was no recognition from the computer that the device was plugged in.
Well as of today, my EEE Transformer is dead. Will not power on the screen, Asus offers a repair of 14 business days, unacceptable.
Powering on issue
Woah...I was scared to death when mine didn't turn on the next morning that I got the device. Charged it for an hour and try to turn on again, nothing.
Holding the buttons several different ways that I know how to reset it didn't work. Finally I held the button down for more than 10 seconds. Wait a few seconds, then it powered on. Why didn't they make a hard reset since you can't remove battery!??? Hope this is just some fluke and could be updated with firmware.
nxp3 said:
Woah...I was scared to death when mine didn't turn on the next morning that I got the device. Charged it for an hour and try to turn on again, nothing.
Holding the buttons several different ways that I know how to reset it didn't work. Finally I held the button down for more than 10 seconds. Wait a few seconds, then it powered on. Why didn't they make a hard reset since you can't remove battery!??? Hope this is just some fluke and could be updated with firmware.
Click to expand...
Click to collapse
Alas, mine didn't get resolved with that, computer detects it now, but no screen response. Asus tells me 14 business days to fix then says try to restore it with the Kernel Source Code. Unfortunately I can't see a way to do such from the folder and they decided to disconnect me.
There is a bug with the default lock screen that makes it so the screen doesnt power on occasionally. In order to work around this you need to disable the lock screen in the settings, or change it from the default one.
Obviously in order to do this initially it needs to be powered on and so you can see it. Therein lies your problem of course. To get around this, charge up your device so you know it has power, use the force power off method (10-12 second press of the power button), wait a few seconds (30+), then power on the device normally (5-6 second press of the power button).
If your screen doesnt come on after that, try a couple more times. It really is an RMA job if it continues to fail. If it does come on, let it boot up to the lock screen, and dont let the screen go off, keep it 'alive', unlock the device and change the lock screen in the options, to either be switched off, or to anything other than default.
This wont work for everyone, as obviously a few may actually have duff screens, but for some of you, it may just be the lock screen bug you are getting unlucky with.
Yea, I seem to have not only the lock screen bug but a defective screen. Unacceptable to me, but hey, what can I do? I've been disconnected 5 times so far, waiting on a manager and will be requesting a faster resolution than what they are offering me. (10-14 Business days is unacceptable)
stuntdouble said:
There is a bug with the default lock screen that makes it so the screen doesnt power on occasionally. In order to work around this you need to disable the lock screen in the settings, or change it from the default one.
Obviously in order to do this initially it needs to be powered on and so you can see it. Therein lies your problem of course. To get around this, charge up your device so you know it has power, use the force power off method (10-12 second press of the power button), wait a few seconds (30+), then power on the device normally (5-6 second press of the power button).
If your screen doesnt come on after that, try a couple more times. It really is an RMA job if it continues to fail. If it does come on, let it boot up to the lock screen, and dont let the screen go off, keep it 'alive', unlock the device and change the lock screen in the options, to either be switched off, or to anything other than default.
This wont work for everyone, as obviously a few may actually have duff screens, but for some of you, it may just be the lock screen bug you are getting unlucky with.
Click to expand...
Click to collapse
naturefreak85 said:
Yea, I seem to have not only the lock screen bug but a defective screen. Unacceptable to me, but hey, what can I do? I've been disconnected 5 times so far, waiting on a manager and will be requesting a faster resolution than what they are offering me. (10-14 Business days is unacceptable)
Click to expand...
Click to collapse
i am in the same boat as you, luckly i picked up the acer for the weekend because i didnt think i was going to get the asus. glad i did
I'm waiting on hold with Asus to see if they will do an Advance Repair, basically I get put on the line for the full price of the device until they declare mine broken since the return period on the Acer is 14 days at best buy. Quite outside of the repair period.
kenshin0088 said:
i am in the same boat as you, luckly i picked up the acer for the weekend because i didnt think i was going to get the asus. glad i did
Click to expand...
Click to collapse
what is the number you are calling, when i called they had almost no idea what i was talking about. they kept asking me if when i am pluged into the wall if thre was a light on the chager when there is no light lol i think they thot i had a laptop or netbook
18886783688 Option 2 Option 2 Option 5
kenshin0088 said:
what is the number you are calling, when i called they had almost no idea what i was talking about. they kept asking me if when i am pluged into the wall if thre was a light on the chager when there is no light lol i think they thot i had a laptop or netbook
Click to expand...
Click to collapse
did you find out anythinig from asus?
kenshin0088 said:
did you find out anythinig from asus?
Click to expand...
Click to collapse
Had to escalate it up to management and expressed I wanted an advance repair and was willing to give them my credit card number so they could place a hold on the card for the amount of a replacement until they got mine. Has to be escalated above the rep should hear back in a couple hours. If not I have an extension and will call back
Sent from my MB860
they are having me download the source code and try and force it to the transformer we will see if it works will report back
I'm having some weird problems getting the phone into download mode. If I hold down voldown + power + trackball, the phone goes into download mode and is recognized, but then leaves download mode about 5 seconds later. The screen goes black and the charging screen turns on for a few seconds and then also goes black. If I just plug in the phone to charge, the charging screen turns on for a few seconds and then cycles with a black screen.
Is there something up with the charging circuitry? Is it possible to get the phone to stay in download mode?
Try doing the forced download mode method
Are you talking about the volume down + trackpad? Same thing happens, download mode screen flashes for ~5 seconds, phone turns off, starts flashing charging screen.
I also have a download mode jig, but that isn't working either.
Also, new development: the phone won't even turn on now when I hold down the power button. Bad battery?
No he means pull battery, connect usb, hold power, volume up, volume down, camera, and tackpad and insert battery. It should FORCE the phone into download mode.
Sent from the phone everyone has forgotten about!
That works, but I still get kicked out of DL mode after about 5 seconds. The issue was never getting into download mode--all button combinations work for that--but the problem is I get kicked out of it after a few seconds.
Hmmmm. I think its probably a bad battery.
Sent from the phone everyone has forgotten about!
Alright. I'll definitely check that out and get a new battery.
Got the battery today. Unfortunately, still the same problem! The Sidekick boot screen now displays in place of the battery charging screen, but I still get kicked out after 5 seconds.
Damn, well the only thing I can think is a problem with the board not receiving enough power. But I don't know, maybe someone else can help you better.
Sent from the phone everyone has forgotten about!
Another thread reminded me...
Fixed the problem! Seemed to be a ribbon cable or some sort of loose connection. I opened up the phone (all the way), removed the RF shield, unplugged all the ribbon/connector cables (minus the one for the camera) and removed the whole board from the phone case. Checked the connections, put everything back together snugly. It now works like a charm.
same problem
would you make a tutorial on how to do this ?
AFAinHD said:
No he means pull battery, connect usb, hold power, volume up, volume down, camera, and tackpad and insert battery. It should FORCE the phone into download mode.
Sent from the phone everyone has forgotten about!
Click to expand...
Click to collapse
AFAinHD said:
Hmmmm. I think its probably a bad battery.
Sent from the phone everyone has forgotten about!
Click to expand...
Click to collapse
I also meet the problem same as Redct and after I tried the solution provideed by Afainhd，the problem has been solved. Thank you Afainhd.
yinyuyang said:
I also meet the problem same as Redct and after I tried the solution provideed by Afainhd，the problem has been solved. Thank you Afainhd.
Click to expand...
Click to collapse
Anytime.
Sent from my Nexus 7 using XDA Premium HD app
SK4g
Yeah i had the same problem iv been trying to go into recovery mode and safe mode. I cant do it im having the same exact problem. I get kicked out every 5 seconds but Redct has a point. There may not be enough power going to the phone. I may attempt at taking the phone apart extremely carefully. If this works ill post then its a manufacture problem for not assembling the phone right or not finding out that people do lots of things with their phone and the phones is just a bunch of computer componets wraped around a piece of plastic. Better quality phones must be sturdy.
So I attempted to take apart the phone and put everything back together and successfully booted. I it booted into the Android OS but then for some reason crashed and entered the boot loop again god this is irritating
Sent from my Nexus 7 using xda app-developers app
Same Problem
I am having the same problem. I took the phone apart, but I couldn't figure out how to get the circuit boards out to unplug the ribbon wires, can you tell me what to do? I had the same problems a few weeks back, but it was staying in download mode then, but now it won't stay in download mode for more than 5 seconds. I got a new phone because of it(LG Optimus). I would really like to get my Sidekick going again though!
Try using heimdal n enable flash bootloaders n hold the volume keys
Sent from my SGH-T959V using xda app-developers app
I'm attempting this fix. Got arround taking out the board and just need some help with what to do with the RF. I can't simply take it out and put it back, my guess. Any help is appreaciated. Like what kind of tool would I need for that? Thanks!
The RF shield or the RF 5000? I'm confused.
BTW... If anyone needs help with how to dismantle the phone, follow this thread. It can be found in General section.
I know this forum is ancient, but I'm working on an E-Bay phone with this exact issue. I found the following thread the most useful and informative on the problem:
http://forum.xda-developers.com/showthread.php?t=1996709
Hopefully this helps other.
I recently downloaded SD Maid Pro, cleaned out all the double files and now the Infuse just blinks Samsung until it dies. Can't get it to go into download mode or anything else. It just blinks Samsung til it dies. I plug in the charger and it just shows the starburst loading emblem. Can't turn it on, once I unplug the charger, it'll show Samsung and then just blink. Pulled the battery, put it back in.. automatically Samsung comes up and just blinks. Tried everything. I think it's done. Any suggestions?
-Rob
Can you tell me step by step how you are trying to get into download mode...maybe you might be doing something wrong...also even if the screen goes blank after doing steps for download mode try and see if Odin/heimdal recognize it
Sent from my HTC PH39100 using XDA
Odin won't recognize it. I pulled the battery. Put it back in. Before I can plug in the usb cable it's flashing the Samsung screen.
Ok, try this
1) Pull battery
2) hold volume up + down
3) plug USB into phone/pc with Odin or heimdal running
4) place battery in
See if it boots into download mode that way
Sent from my HTC PH39100 using XDA
Nope, Just shows the starburst loading icon blinking like before.
Hmmm...well, if your not too sketched out and you pay for shipping, ill take a look at it and try to fix it...this is just an option and I understand if you don't wanna do that option ad I am a stranger and these phones ate expensive...
Can you check the power button...make sure its not stuck down...helped a guy not too long ago who had a similar problem only to find out his power button was stuck down
Sent from my HTC PH39100 using XDA
BigRob1212 said:
Nope, Just shows the starburst loading icon blinking like before.
Click to expand...
Click to collapse
let is set for a few hours, may need to charge...
or buy a usb jig and see if that will force it into download mode... worked for me once.
como ysickp
I'm having the same issue here, but my phone hit nicely my bedside... it turns on, but keeps looping in the samsung screen
sorry for english
doggie3001 said:
I'm having the same issue here, but my phone hit nicely my bedside... it turns on, but keeps looping in the samsung screen
sorry for english
Click to expand...
Click to collapse
Have you attempted download mode? Could you also provide the steps you did to attempt download mode?
Sent from my HTC PH39100 using XDA
mg2195 said:
Have you attempted download mode? Could you also provide the steps you did to attempt download mode?
Sent from my HTC PH39100 using XDA
Click to expand...
Click to collapse
Yes, i've tried almost everything to get in download mode
download modes
nothing works it's like my power button is stuck, but it looks fine
M8, im dealing with the same situation with a couple motherboards. If im able to find a solution for that i will let you know. Ive done more than you have because i have even applied unbrickable mod to one of those two mobos with no luck. Pretty much same thing. The resurrector recognizes it but before it can resurrect the phone it will dissappear for good. So im starting to think it could be a damaged or corrupted file on the very lower levels of the infuse. But, at the same time, it maybe some hardware failure since i think unbrickable mod basically goes to the lowest level on the phone. Its a shame, but i have seen this many times on infuse phones. Never had to deal with that myself though....
Possible fix
My son brought me his phone last night with this same problem. I was not in the best mood to deal with it so made him, a teenager, go without a phone for a whole night....yeah dad of the year here. LOL. Anyway, I started working on it this morning and tried just about everyting I could think of until it thought of the Handyman's#! rule....If it doesnt work just bang on it. I took phone and with battery in it and cover on slapped it against my knee on the back cover in area where camera is. Dont try to break it just give it a good smack. Right after that it booted up and is just fine. LOL. I know it isnt the most scientific way to fix it...but it works for me and my son has his phone back. I hope this will help the rest of you out until we have a more defined solution.
i just got this phone from a friend it was rooted an stuck in boot loop so i flashed a normal s2 rom not thinking this was a s2 skyrocket now no power or nothing is there anything i can do to fix it no recovery an it will not boot into download mode
krazydude4g said:
i just got this phone from a friend it was rooted an stuck in boot loop so i flashed a normal s2 rom not thinking this was a s2 skyrocket now no power or nothing is there anything i can do to fix it no recovery an it will not boot into download mode
Click to expand...
Click to collapse
Sorry dude if it doesn't connect via usb you've pretty much got a paper weight.
My moms basement.
Look up jtag. It's your only option at this point. Unless the phone was purchased under a year ago. So yeah, paperweight for now.
thanks for the help i figured the skyrocket would say sky rocket on it lol so i just jumped into the s2 i777 forum like a noob i feel so dumb but will the jtag thing for sure fix it
Almost nothings for sure but it's a pretty good chance they revive it. mobiletechvideos is who a lot of people have used.
ok what about the usb jig thing has anyone tried that an how much does the jtag fix usaully cost
krazydude4g said:
ok what about the usb jig thing has anyone tried that an how much does the jtag fix usaully cost
Click to expand...
Click to collapse
no, wont work for the i727, just call these guys http://mobiletechvideos.mybigcommerce.com/samsung-galaxy-s-ii-skyrocket-jtag-brick-repair/
Try to install USB drivers switch off and press call or volume button while connecting usb
DONT FORGET HITTING THANKS......
yash.pranjale86 said:
Try to install USB drivers switch off and press call or volume button while connecting usb
DONT FORGET HITTING THANKS......
Click to expand...
Click to collapse
its hardbricked, like op stated, no power no nothing
yes i am for sure its hard bricked im so mad at my self i could rip my head off lol but i guess thats what i get for rushing into it im guessing everone would reccomend the mobiletechvideos fix for 50 instead of the 30 dollar ones on ebay or does it matter?
Spend the extra 20 bucks. lol It might matter or it might not. You don't wanna be the one that finds out it mattered though. lol
I would trust mobile techvideos over anyone on ebay. They have a stellar rep.
mimart7 said:
I would trust mobile techvideos over anyone on ebay. They have a stellar rep.
Click to expand...
Click to collapse
+1
My moms basement.
Possible bootloop fix without jig or any other 3rd party means
krazydude4g said:
i just got this phone from a friend it was rooted an stuck in boot loop so i flashed a normal s2 rom not thinking this was a s2 skyrocket now no power or nothing is there anything i can do to fix it no recovery an it will not boot into download mode
Click to expand...
Click to collapse
Hey there, Today my phone got stuck in a bootloop where the screen was black and there was an intermittent vibration. I couldn't get out of this bootloop at all. I tried getting into recovery mode, download mode, using Odin, holding down power for more than 20 seconds, removing the battery for 10 minutes, etc. Anyway, I figured, there has to be a solution without having to take apart my phone and trying to use JTAG, Geez! ANyway, I decided to try pressing the power and volume buttons in different combinations with and without the battery, and while being connected or disconnected to the PC. OK to make a long story short, here is the combination.
Plug USB into computer ( I used win7) without connecting it to your skyrocket.
Remove the battery from your phone.
Insert the Data cable into your phone without the battery.
Install battery and quickly press both the volume up/down button and the power button repeatedly (about 5-10 times) Basically press and release both sides at the same time over and over again until your skyrocket pops out of a bootloop. It took me only 5 presses.
I'm not saying this will work for everyone, but it worked for me. Due to the fact that this happened on a whim, I can't test it out to make sure the steps are just right. Whoever tries this, take note of the steps.
I hope this helps you guys out. Cheers.
peter7del said:
Hey there, Today my phone got stuck in a bootloop where the screen was black and there was an intermittent vibration. I couldn't get out of this bootloop at all. I tried getting into recovery mode, download mode, using Odin, holding down power for more than 20 seconds, removing the battery for 10 minutes, etc. Anyway, I figured, there has to be a solution without having to take apart my phone and trying to use JTAG, Geez! ANyway, I decided to try pressing the power and volume buttons in different combinations with and without the battery, and while being connected or disconnected to the PC. OK to make a long story short, here is the combination.
Plug USB into computer ( I used win7) without connecting it to your skyrocket.
Remove the battery from your phone.
Insert the Data cable into your phone without the battery.
Install battery and quickly press both the volume up/down button and the power button repeatedly (about 5-10 times) Basically press and release both sides at the same time over and over again until your skyrocket pops out of a bootloop. It took me only 5 presses.
I'm not saying this will work for everyone, but it worked for me. Due to the fact that this happened on a whim, I can't test it out to make sure the steps are just right. Whoever tries this, take note of the steps.
I hope this helps you guys out. Cheers.
Click to expand...
Click to collapse
what you have sir is a stuck power button, by repeadetly pressing the power button you momentarily "unstuck" the button, it can stay unstuck like that or it can become "sticky" once again, more info on that in the 1stop sticky
peter7del said:
Hey there, Today my phone got stuck in a bootloop where the screen was black and there was an intermittent vibration. I couldn't get out of this bootloop at all. I tried getting into recovery mode, download mode, using Odin, holding down power for more than 20 seconds, removing the battery for 10 minutes, etc. Anyway, I figured, there has to be a solution without having to take apart my phone and trying to use JTAG, Geez! ANyway, I decided to try pressing the power and volume buttons in different combinations with and without the battery, and while being connected or disconnected to the PC. OK to make a long story short, here is the combination.
Plug USB into computer ( I used win7) without connecting it to your skyrocket.
Remove the battery from your phone.
Insert the Data cable into your phone without the battery.
Install battery and quickly press both the volume up/down button and the power button repeatedly (about 5-10 times) Basically press and release both sides at the same time over and over again until your skyrocket pops out of a bootloop. It took me only 5 presses.
I'm not saying this will work for everyone, but it worked for me. Due to the fact that this happened on a whim, I can't test it out to make sure the steps are just right. Whoever tries this, take note of the steps.
I hope this helps you guys out. Cheers.
Click to expand...
Click to collapse
uhhhh, another person who is slightly misinformed. a boot loop doesn't equal JTAG. if your phone turns on AT ALL u should be able to recover it and get it working. JTAG is required for a brick, and like its name implies, a brick is just that. A phone that does absolutely nothing but sit there. No display, no sound, no vibrate, nuthin
icenight89 said:
uhhhh, another person who is slightly misinformed. a boot loop doesn't equal JTAG. if your phone turns on AT ALL u should be able to recover it and get it working. JTAG is required for a brick, and like its name implies, a brick is just that. A phone that does absolutely nothing but sit there. No display, no sound, no vibrate, nuthin
Click to expand...
Click to collapse
The original op was hard bricked, jtag refers to him
God promised men that he'd put beautiful women in all corners of the world. Then he laughed and laughed and made the world round
if you have a car charger try it... cause i dont know if its for me alone but my car charger works as a jtag when the phone is off
orbourne53 said:
if you have a car charger try it... cause i dont know if its for me alone but my car charger works as a jtag when the phone is off
Click to expand...
Click to collapse
a car charger will never ever act work as a jtag......ever.
i meant to say put the phone in download mode if thats what jtag is