Database Info

Root? Kingroot?

What's going on with kingroot for Xperia z3 lolipop 5.1.1? There is a date for available kingroot for this version?

No there isn't. Kingroot only supports 5.0 not 5.1 You could always flash 5.0.2, root with kingroot then flash a pre-rooted 5.1.1

heywheelie said:
No there isn't. Kingroot only supports 5.0 not 5.1 You could always flash 5.0.2, root with kingroot then flash a pre-rooted 5.1.1
Click to expand...
Click to collapse
I did it but when I updated to 5.1.1 the Root was deleted

DANIELTZ19 said:
What's going on with kingroot for Xperia z3 lolipop 5.1.1? There is a date for available kingroot for this version?
Click to expand...
Click to collapse
No date available...
I'm waiting for it too :crying:

DANIELTZ19 said:
I did it but when I updated to 5.1.1 the Root was deleted
Click to expand...
Click to collapse
Did you flash a stock 5.0.2, then root with kingroot, install the latest dual recovery from PC, boot to recovery, do a complete wipe then flash a pre-rooted 5.1.1 from recovery. It should work. I tried it here, worked perfectly.
BTW make sure you put the pre-rooted 5.1.1 on your sdcard before you start so once you go into recovery to do a full wipe you don't reboot until you flash the pre-rooted 5.1..1

heywheelie said:
Did you flash a stock 5.0.2, then root with kingroot, install the latest dual recovery from PC, boot to recovery, do a complete wipe then flash a pre-rooted 5.1.1 from recovery. It should work. I tried it here, worked perfectly.
BTW make sure you put the pre-rooted 5.1.1 on your sdcard before you start so once you go into recovery to do a full wipe you don't reboot until you flash the pre-rooted 5.1..1
Click to expand...
Click to collapse
I don't install pre-rooted 5.1.1 because it needs to Recovery .. and I don't want to do a recovery in my device .... i just Burning a normal version of 5.1.1

DANIELTZ19 said:
I don't install pre-rooted 5.1.1 because it needs to Recovery .. and I don't want to do a recovery in my device .... i just Burning a normal version of 5.1.1
Click to expand...
Click to collapse
Then just delete the recovery after you have flashed the pre rooted 5.1.1. The ramdisks are in the system partition.

gregbradley said:
Then just delete the recovery after you have flashed the pre rooted 5.1.1. The ramdisks are in the system partition.
Click to expand...
Click to collapse
If I do now Recovery then it deletes all my stuff in the cell phone .. other than that it will lose my warranty and it might make my cell phone issues

DANIELTZ19 said:
If I do now Recovery then it deletes all my stuff in the cell phone
Click to expand...
Click to collapse
It should not do that if you do it properly. You only lose stuff in your phone if you unlock the bootloader and you do not need to do that. Also, making a backup of things you want to keep is always a good idea.
DANIELTZ19 said:
.. other than that it will lose my warranty and it might make my cell phone issues
Click to expand...
Click to collapse
No you will not lose warranty if you follow the locked bootloader tutorial. You do not need to unlock the bootloader to install recovery and flash a pre-rooted 5.1.1
Please take a moment to look through any of the multiple guides in the general section to see how to do this

gregbradley said:
It should not do that if you do it properly. You only lose stuff in your phone if you unlock the bootloader and you do not need to do that. Also, making a backup of things you want to keep is always a good idea.
No you will not lose warranty if you follow the locked bootloader tutorial. You do not need to unlock the bootloader to install recovery and flash a pre-rooted 5.1.1
Please take a moment to look through any of the multiple guides in the general section to see how to do this
Click to expand...
Click to collapse
Okay, thank you very much, but there will be no hacking with "Kingroot"? This is the most easy and simple ..

DANIELTZ19 said:
Okay, thank you very much, but there will be no hacking with "Kingroot"? This is the most easy and simple ..
Click to expand...
Click to collapse
Kingroot will send your IMEI to an IP address in china, I do not recommend it. Downgrade and use giefroot, install dual recovery, flash a pre rooted 5.1.1, then delete the recovery if you want, but I do not see why you would do this.

gregbradley said:
Kingroot will send your IMEI to an IP address in china, I do not recommend it. Downgrade and use giefroot, install dual recovery, flash a pre rooted 5.1.1, then delete the recovery if you want, but I do not see why you would do this.
Click to expand...
Click to collapse
Because that everyone I know who did Recovery then it's destroyed a lot of things on the device ..

DANIELTZ19 said:
Because that everyone I know who did Recovery then it's destroyed a lot of things on the device ..
Click to expand...
Click to collapse
You are confusing recovery with losing drm keys when unlocking the bootloader.
I have never come across anyone who has recovery installed correctly and used correctly who has had problems like that

@DANIELTZ19
If you're worried and want another opinion then my advice is that everything GregBradley has stated is correct. His method is also the safest and reliable with an excellent tutorial in the General forum. Read it http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056
cheers

Is there a way to root on 5.1.1 23.4.A.1.200 ?

Hello there,
have been trying to root my new xperia z3 for 3 weekends now with no luck.
My bootloader has been unlocked through sony website, then relocked and unlocked many times using flashtool.
Looks like all the recoveries (doomlord, twrp) I could find work only on 4.4.4. Then I use flashtool to flash lollipop 5.1.1 23.4.A.1.200 and either wipe and loose the root or don't wipe all and enter a bootloop.
Flashing those recovery kernels straight on lollipop make the phone enter bootloop.
Are you guys able to root those Z3 under 5.1.1 ?
thank you

Sure shot easy way is flash kitkat firmware and use giefroot or flash 5.0 firmware and use kingroot.

Mate, you have to flash a prerooted version of 5.1.1 you can't just flash a stock rom and expect to stay rooted.
Downgrade to Kitkat then root and install a custom recovery. Then you download 5.1.1, Super Su and a custom recovery, create a pre rooted flashable zip with PRFcreator . Then flash it in your custom recovery and you're done. Rooted 5.1.1 with a custom recovery ready to rock.

Kingroot isn't recommendable, your IMEI is sent to China. Downgrade to 4.4, root with giefieroot, upgrade with pre-rooted ROM.
Btw: did you make a backup of your TA partition before unlocking bootloader?

Thanks a lot for your answer guys.
Am unusually struggling with this device.
lol1rfs said:
Mate, you have to flash a prerooted version of 5.1.1 you can't just flash a stock rom and expect to stay rooted.
Downgrade to Kitkat then root and install a custom recovery. Then you download 5.1.1, Super Su and a custom recovery, create a pre rooted flashable zip with PRFcreator . Then flash it in your custom recovery and you're done. Rooted 5.1.1 with a custom recovery ready to rock.
Click to expand...
Click to collapse
Have already downgraded to kitkat, installed custom recovery and rooted. But the 5.1.1 stock flash indeed wipe everything.
Haven't found yet a custom recovery for 5.1.1 that doesn't make the phone enter a bootloop. Would you happen to have a link ?
I'll give a look to that PRFcreator, didn't know about it.
Jkay7 said:
Kingroot isn't recommendable, your IMEI is sent to China. Downgrade to 4.4, root with giefieroot, upgrade with pre-rooted ROM.
Btw: did you make a backup of your TA partition before unlocking bootloader?
Click to expand...
Click to collapse
This is what I read about kingroot and haven't found any other way to root a 5.1.1 stock.
Where could I find a pre-rooter ROM then ? My wish was to be stock and rooted to be able to use apps like titanium backup and adblockers. Used to try custom roms every other day on my old SGS but today I'd be happy with something that just works.
Did not make any backup before unlocking but looked like flashtool was able to relock the device. Am I right guessing I didn't loose my DRM keys then ?
Thanks again for your answers.
Edit: looks like am missing sthg, what's the point in rooting a kitkat to upgrade with a pre-rooted lollipop right after ?

After KitKat root you get a Lollipop pre-rooted image and flash it: http://forum.xda-developers.com/z3/general/d6603-5-0-2-flashable-stock-23-1-0-690-t3056361
Here are the steps: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056

I hope you made a TA backup before unlocking your bootloader, otherwise you have lost your DRM keys forever.
Anyway, if your bootloader is now locked, follow the guide that Licaon_Kter linked in the above post.
The exploit that lets us root our Z3 only works on Kitkat, so downgrade first, run the exploit to obtain root, and install recovery.
You will then have stock, rooted, KitKat.
To get to 5.1.1, you will then need to either create your own pre rooted firmware, or download one that someone has kindly posted on here.
If you want to learn how to do it, read this --> Create your own pre rooted firmware with PRF Creator
PRF Creator will create a zip file that can be flashed from recovery, so once you have recovery installed, it's dead easy.
That will get you where you want to be.
However . . . and there's always a however lol . . .
. . . if you still have an unlocked bootloader, it is much simpler from wherever you are.
Find any custom rom that has recovery built in, and almost all do, then fastboot the kernel only, the boot.img.
Reboot your device and enter recovery.
Install your pre rooted firmware that you have either created with PRF Creator, or downloaded from here.
Job done.
My personal advice is read, read, and then read some more.
It can be very complicated, but you'll get the hang of it.

Licaon_Kter said:
After KitKat root you get a Lollipop pre-rooted image and flash it: http://forum.xda-developers.com/z3/general/d6603-5-0-2-flashable-stock-23-1-0-690-t3056361
Here are the steps: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056
Click to expand...
Click to collapse
I still have an unlocked bootloader since flashtool can lock and unlock it in a matter of a second.
Went back again in KK rooted with twrp recovery.
Wiped data, cache, dalvik.
Flashed D6603_23.4.A.1.232_Customized_US_SuperSU_XZDR2.8.2 1 from the link above and ... CWM recovery report install from sdcard completed after 1s and nothing more. Am still booting in KK after that.
This didn't work for me. Am losing it now with this phone.
Am I missing sthg ? Any advice ?
Can't use PRFCreator, am under mac os...
Thanks to all for your help

Try with TWRP too

Licaon_Kter said:
After KitKat root you get a Lollipop pre-rooted image and flash it: http://forum.xda-developers.com/z3/general/d6603-5-0-2-flashable-stock-23-1-0-690-t3056361
Here are the steps: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056
Click to expand...
Click to collapse
Licaon_Kter said:
Try with TWRP too
Click to expand...
Click to collapse
tried twrp found there http://forum.xda-developers.com/z3/development/recovery-z3-twrp-2-8-4-0-t3028846
phone is not booting anymore.
twrp post says it doesn't work on stock room.
---------- Post added at 02:16 PM ---------- Previous post was at 02:05 PM ----------
Is there really anyone out there with a rooted stock lollipop ?
or you are all using customs ?
am seriously questionning the thing now

Why would you NOT follow the steps?
GO AGAIN from the start: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056

Licaon_Kter said:
Why would you NOT follow the steps?
GO AGAIN from the start: http://forum.xda-developers.com/z3/general/guide-rootrecovery-how-to-root-install-t3017056
Click to expand...
Click to collapse
I just can't, I don't have access to a window machine

Both giefroot and FlashTool are for Win/Mac/Linux.

Licaon_Kter said:
Both giefroot and FlashTool are for Win/Mac/Linux.
Click to expand...
Click to collapse
I appreciate your still trying to help me.
I do use flashtool and am able to root a Kitkat 23.0.A.2.93, so I don't see the point in using giefroot unless it could root a lollipop.
I have read thoroughly and downloaded pre-rooted lollipop stock roms from the link you provided.
Once under KK, rooted, with all settings set properly (debug, security, etc...), and all caches/dalvik/data wiped, the CMW recovery just don't flash those lollipop roms. After just one sec, it says install completed but then the device still boot under KK.
TWRP doesn't even intall, so am wondering if this is even possible to get a TWRP on stock rom.
Have tried all of those with bootloader unlocked and locked, or a mix like unlocked first to be able to root a KK, then relock to flash a stock prerooted 5.1.1 (as stated in the post) but then I get a device that doesn't even boot.
Tried dualrecovery too, flash the zip, and nothing.
I suspect all of you guys have used some sort of .bat windows utility to get through this.
Once again, thanks for your help and patience.

ikho said:
I do use flashtool and am able to root a Kitkat 23.0.A.2.93, so I don't see the point in using giefroot unless it could root a lollipop.
Click to expand...
Click to collapse
The point is to go from the BEGINing _again_: Flash stock KK, giefroot, XZ, pre-rooted LP
I have done it in Linux w/ locked bootloader and stock ROM, hence my pointers.
XZDualrecovery has TWRP 2.8.7.0. But, do take note that you use Volume Down to enter PhilzTouch Recovery and Volume Up to enter TWRP.

Licaon_Kter said:
Both giefroot and FlashTool are for Win/Mac/Linux.
Click to expand...
Click to collapse
am sorry, can't find how to use giefroot on a mac.
read quite a few post of people saying that was not working for them.

Run the INSTALL.SH file in a console (just like they instruct you for the .BAT file for Windows), it detects OS and runs either adb for Linux or for Mac.
Well, like I said, it worked fine in Linux, I guess it should work on Mac, providing the device is detected ok beforehand and such. ( what does "adb devices" outputs with the phone connected ? )

Licaon_Kter said:
Run the INSTALL.SH file in a console (just like they instruct you for the .BAT file for Windows), it detects OS and runs either adb for Linux or for Mac.
Well, like I said, it worked fine in Linux, I guess it should work on Mac, providing the device is detected ok beforehand and such. ( what does "adb devices" outputs with the phone connected ? )
Click to expand...
Click to collapse
yaaay, houray it finally worked
big thanks man, you saved me $500 on that one !

DISCONTINUED_[VZW_Stock TW Rom][6.0.1 MM QA1 Build Odex For Locked Bootloader SafeStrap Only]

Do Not Flash This On Unlocked Bootloaders Or You Will Relock Your Bootloader!!!​Once your on MM 6.0.1 you cannot restore a Lollipop Backup using SafeStrap or vice versa. Follow the link at bottom of post for guide and files to downgrade back to Lollipop
Ok the first thing I want to make clear is YOU WILL NOT HAVE ROOT! You will still have the use of Safestrap Recovery even though phone will not be rooted. What this will allow you to do is boot the non rooted rom back into safestrap. While in Safestrap you can do what you have always done, Flash Zips, Make Backups,Etc. This will also make it easy if you want to go back to PB1 rooted rom.
You must be on A rooted rom preferably A PB1 rom running SafeStrap
If Running FlashFire
Make sure latest busybox is installed
Install MM_Safestrap.apk
Reboot to safestrap
Wipe Data,Cache,System
Install VZW_QA1_STOCK_SAFESTRAP_ONLY_V2.zip
Roms will take a long time to boot up be patient!
This will put you on pure stock rom MM QA1 rom but from here you can get to safestrap to flash other roms or mods
To return to Safestrap you will need to flash a kitkat kernel NI2_stock_kernel.tar.md5 using odin then when phone reboots click on enter safestrap recovery. When leaving safestrap you must flashMM_KERNEL_SS-FF_Flashable.zip. Which will be located on your internal storage In a folder called MM_KERNEL_SS-FF_Flashable
If you want to flash other custom roms a guide can be found HERE

Useful zips
View attachment ADBlocking_2_5_17.zip
View attachment DebloatScript.zip

Thanks Jkruse!
Question... I tried your stock PB1 before and it worked well. I however hosed myself flashing the incorrect firmware and USB bulk mode occured when I attempted to go back to PHX11 5.0 ROM. I flashed firmware as when I reloaded the backup of PHX 11 I had no data or wifi.
I saved the phone however and need to know what is the correct procedure to go back to LP backups if I try this and decide not to stay? I want to avoid bulk mode again!
Thank you!!

ridenickel9 said:
Thanks Jkruse!
Question... I tried your stock PB1 before and it worked well. I however hosed myself flashing the incorrect firmware and USB bulk mode occured when I attempted to go back to PHX11 5.0 ROM. I flashed firmware as when I reloaded the backup of PHX 11 I had no data or wifi.
I saved the phone however and need to know what is the correct procedure to go back to LP backups if I try this and decide not to stay? I want to avoid bulk mode again!
Thank you!!
Click to expand...
Click to collapse
Once your on this rom The link at the bottom of the OP has a guide and files for going back to lollipop BP1 build without having to reroot. It's in the second post of that guide

jrkruse said:
Once your on this rom The link at the bottom of the OP has a guide and files for going back to lollipop BP1 build without having to reroot. It's in the second post of that guide
Click to expand...
Click to collapse
I'll read up! Thank you!!
Would this be the same procedure for OG5 just substitute the PB1 caution firmware with OG5 caution firmware? I assume just match the ROM you go to with the caution zips that don't contain the bootloader.
Pretty sure I didn't use the caution firmware before and that what caused my issues.

ridenickel9 said:
I'll read up! Thank you!!
Would this be the same procedure for OG5 just substitute the PB1 caution firmware with OG5 caution firmware? I assume just match the ROM you go to with the caution zips that don't contain the bootloader.
Pretty sure I didn't use the caution firmware before and that what caused my issues.
Click to expand...
Click to collapse
If you goback to lollipop it will need to be PB1

Added debloat script to post 2 that can be flashed with safestrap

jrkruse said:
If you goback to lollipop it will need to be PB1
Click to expand...
Click to collapse
OK thank you for clarifying. I use PHX 11 and always need to flash the OG5 kernal from safe strap so I assumed I'd need OG5 firmware for that particular situation.
Also thanks for updating the OP about using backups to and from MM - that will help others avoid issues.
I'll stop clogging the thread now! Appreciate all the information and work you do!!

Hey, thanks for this great site and all of your guides. It really helps.
I just rooted my s5 g900v and Im still on KITKAT NK2. Would it be possible for me to update from that version to this one following your guide?
Sorry for asking really basic questions. My phone at the moment is sim unlocked and rooted, but CID starts with 11 so I cannot unlock the boatloader, right? Then I assume this ROM is my best option. I want to be really sure that I will still be sim unlocked on the new ROM, its got nothing to do with it, right?
Many many thanks in advanced!

nachoalt said:
Hey, thanks for this great site and all of your guides. It really helps.
I just rooted my s5 g900v and Im still on KITKAT NK2. Would it be possible for me to update from that version to this one following your guide?
Sorry for asking really basic questions. My phone at the moment is sim unlocked and rooted, but CID starts with 11 so I cannot unlock the boatloader, right? Then I assume this ROM is my best option. I want to be really sure that I will still be sim unlocked on the new ROM, its got nothing to do with it, right?
Many many thanks in advanced!
Click to expand...
Click to collapse
Yes you can update to this rom and also verizon phones are all sim unlocked so it will rermain sim unlocked. Just remember if your still on kitkat when you flash anything with safestrap do not use rom slots flash on the stock rom slot. If you dont know what this means then dont worry about it

jrkruse said:
Added debloat script to post 2 that can be flashed with safestrap
Click to expand...
Click to collapse
Thanks for the hard work, unfortunately my cid 15 just took a nice fat swim and i had to get a replacement and got a cid 11 instead (##$$%@@@!#[email protected]). Your guides have been great to get to this point but got a couple questions:
Any link to what the debloat script removes? I just ran it and it doesn't seem to remove anything (ran it at same time as addblock). Going to reboot and flash it again see if it does. Any way we can remove the stuff we don't want? (all the VZW junk)

How to install Oreo ROM?

Hi! I'm really humbly sorry, I'm new to this stuff, so I have to ask you...
I have a Galaxy S8+ Duos (SM-GD955FD). I bricked it once or twice trying to root it. So I had to flash a sammobile.com ROM...
Now this is done, I have a successfully rooted phone with with the Baseband version G955FXU1AQH3 and the irritating "security notice" (since I was not able to install Magisk, and the NotifyClean app doesn't work either).
I would like to flash the latest Oreo and root it. I also heard good things about the Oreo ROM by alexega.
So: I'm on AQH3 rooted. What can I do?
Thank you for your patience.

If wou want to install stock ROM you must follow this instructions: https://forum.xda-developers.com/galaxy-s8+/how-to/guide-how-to-flash-crap-using-odin-t3748555. Bear in mind that if you install stock due to security issues you can't unlock OEM for 7 days after flashing (you must not reboot your phone for 170 hours).
If wou want to flash a custom rom you must have TWRP installed, move the zip rom to your SD card and just flash it from recovery. Make sure to format data before flashing.

josegon30 said:
If wou want to install stock ROM you must follow this instructions: https://forum.xda-developers.com/galaxy-s8+/how-to/guide-how-to-flash-crap-using-odin-t3748555. Bear in mind that if you install stock due to security issues you can't unlock OEM for 7 days after flashing (you must not reboot your phone for 170 hours).
If wou want to flash a custom rom you must have TWRP installed, move the zip rom to your SD card and just flash it from recovery. Make sure to format data before flashing.
Click to expand...
Click to collapse
Nice, thank you. So I have just flashed the thing with the sammobile.com ROM again (so, no root) and updated to the oroginal firmware Oreo following your link (I worked parallel).
I was just about to root Oreo and was googling for a way... But did I get you right? I should not reboot my phone for 170 hours now?!? So, no rooting until next week?!
Edit: I have developer options enabled and the "OEM unlock" switch is on (it says: "Bootloader is already unlocked.""). So... confusion...

andifla852 said:
Nice, thank you. So I have just flashed the thing with the sammobile.com ROM again (so, no root) and updated to the oroginal firmware Oreo following your link (I worked parallel).
I was just about to root Oreo and was googling for a way... But did I get you right? I should not reboot my phone for 170 hours now?!? So, no rooting until next week?!
Edit: I have developer options enabled and the "OEM unlock" switch is on (it says: "Bootloader is already unlocked.""). So... confusion...
Click to expand...
Click to collapse
Excuse me, are you currently on Nougat 7.0? If so, you obviously have OEM unlock option available. The problem is in the new 8.0 stock rom, wich sets RMM state to pre-normal preventing you to flash TWRP and to get root in OREO. To skip that you can directly flash a custom rom with 8.0.- Otherwise (stock rom) you must wait 7 days with no phone reboot to get ridd of that pre-normal issue and then flash TWRP and flash Magisk.

Just rooted the new Oreo ROM with TWRP. Works just fine, thank you.
So, what are the advantages of the Oreo ROM by alexega compared to XXU1CRAP?

josegon30 said:
Excuse me, are you currently on Nougat 7.0? If so, you obviously have OEM unlock option available. The problem is in the new 8.0 stock rom, wich sets RMM state to pre-normal preventing you to flash TWRP and to get root in OREO. To skip that you can directly flash a custom rom with 8.0.- Otherwise (stock rom) you must wait 7 days with no phone reboot to get ridd of that pre-normal issue and then flash TWRP and flash Magisk.
Click to expand...
Click to collapse
Hi Jose. I am with stock nogat. Not root. Any advice for flash stock oreo firmware?
Allrey know about odin. Im talking about unlock options, etc.
Thks
Juan from Argentina.

juange said:
Hi Jose. I am with stock nogat. Not root. Any advice for flash stock oreo firmware?
Allrey know about odin. Im talking about unlock options, etc.
Thks
Juan from Argentina.
Click to expand...
Click to collapse
Just follow the steps from the link in my previous repply. As it's an original software, it won't trip knox or void your warantee.

hi, does anybody knows how to install the oreo firmware using odin but without changing the csc I already have?

josegon30 said:
Excuse me, are you currently on Nougat 7.0? If so, you obviously have OEM unlock option available. The problem is in the new 8.0 stock rom, wich sets RMM state to pre-normal preventing you to flash TWRP and to get root in OREO. To skip that you can directly flash a custom rom with 8.0.- Otherwise (stock rom) you must wait 7 days with no phone reboot to get ridd of that pre-normal issue and then flash TWRP and flash Magisk.
Click to expand...
Click to collapse
Do you need a custom rom to not have the RMM lock anymore? A stock with BlackMesa's RMM START .zip is not right?

costafabiof said:
Do you need a custom rom to not have the RMM lock anymore? A stock with BlackMesa's RMM START .zip is not right?
Click to expand...
Click to collapse
There's no need to have a custom rom, if you flash the fix in stock RMM lock gets killed everytime.

josegon30 said:
There's no need to have a custom rom, if you flash the fix in stock RMM lock gets killed everytime.
Click to expand...
Click to collapse
Did not work.
I can not find out where I went wrong.

developer11 said:
Android.com.pl **** you
Little cocksucker
Click to expand...
Click to collapse
Translation?

costafabiof said:
Did not work.
I can not find out where I went wrong.
Click to expand...
Click to collapse
First you have to install OREO and wait 7 days without reseting your phone. After 170 hours, you get OEM unlock in developer options and you will be able to flasf TWRP. After flashing TWRP you flash RMM-State_Bypass_Mesa and that´s all.

josegon30 said:
First you have to install OREO and wait 7 days without reseting your phone. After 170 hours, you get OEM unlock in developer options and you will be able to flasf TWRP. After flashing TWRP you flash RMM-State_Bypass_Mesa and that´s all.
Click to expand...
Click to collapse
That did not work out. But thank you for your attention.

DISCONTINUED_VZW_Stock_QL1_Deodexed DEV aboot Rooted Locked Bootloader Safstrap

The easiest method to obtain root unlocks or update or downgrade unlocked bootloaders can be found below they were updated December of 2021​
EMMC 15 Unlocking Bootloader
2022_VZW_EMMC_15_ AIO_Tool To Unlock_Bootloader+Install_TWRP And MM_QL1_Rooted_Rom Works On Any Version Bootloaders_MM_LL_KK-Reactivation Lock Remover
This Process Will Root Phone Unlock Your VZW EMMC 15 Chipset Bootloader Install TWRP Recobery And Imstall Latest QL1 Stock Rom . Downloads S5_Root_Tools_2023.7z EMMC_15_Rom.zip -- Stock QL1 6.0 Directions For Unlocking Stock Phone I would...
forum.xda-developers.com
EMMC 15 Updating Unlocked Bootloaders Or Downgrading
2022_VZW_EMMC_15_Chipset For Unlocked Dev BL To Downgrade To LL_KK Or Upgrade To MM_And Keep Unlock Bootloader
This Process Will Update Or Downgrade Your VZW EMMC Chipset DEV Aboot Bootloader Unlocked S5 To Marshmallow 6.0 Lollipop 5.0 Or Kitkat 4.2 or 4.4 Root And Unlock Instructions Can Be Found Here EMMC 15 Rooting And Bootloader Unlocking EMMC 11...
forum.xda-developers.com
For Rooting EMMC 11 Phones
2021_VZW_Locked_Bootloader_EMMC_11_Rooted/NonRooted_Roms_With_Safestrap_MM_LL_KK
This Process Will Install On The EMMC_11 Locked Bootloader Verizon S5 Marshmallow QL1 Stock Rom NonRooted With Safestrap. Lollipop PB1 Stock Rom Rooted With Safestrap. KK Rom Rooted With Safestrap What This Does This gives you the ability to...
forum.xda-developers.com

mine

jrkruse said:
Disclaimer
I will not offer much support for this. These methods work and have been around for a long time now
Click to expand...
Click to collapse
Thank you friend, this is an amazing treasure chest with every posable tool needed for moding the Verizon variant s5. I know that you have moved on to new projects and phones a long time ago, so thanks again for taking your time and energy to do this for us.
Sent from my kltevzw using XDA Labs

This is a very good OP @jrkruse! :thumbup:
I know that you had worked hard for both the development as well as the instructions provided.
Kudos My Friend!
~~~~~~~~~~~~~~~
UNLESS asked to do so, PLEASE don't PM me regarding support. Sent using The ClaRetoX Forum App on my SM-G900V device.

Just a simple question.
I'm not very experimented with the whole s5 modding thing, but is there really no way to have root on cid11 mm ?

DRAKUL666 said:
I'm not very experimented with the whole s5 modding thing, but is there really no way to have root on cid11 mm ?
Click to expand...
Click to collapse
There really is no way to have root on Android Marshmallow 6.0 with Emmc_CID_11 but you have safestrap so you can install xposed or most mod zips , delete system files you dont want etc

Hi I flash the rom ... Now my phone is very slow and freezes ... any help plz .

sjla said:
Hi I flash the rom ... Now my phone is very slow and freezes ... any help plz .
Click to expand...
Click to collapse
What ROM?
Sent from my kltevzw using XDA Labs

swiftbones74 said:
What ROM?
Sent from my kltevzw using XDA Labs
Click to expand...
Click to collapse
[ROM][VZW_Stock _QL1_Deodexed][DEV aboot Magisk Rooted][Locked Bootloader Safstrap] by jrkruse ..... these rom

sjla said:
[ROM][VZW_Stock _QL1_Deodexed][DEV aboot Magisk Rooted][Locked Bootloader Safstrap] by jrkruse ..... these rom
Click to expand...
Click to collapse
In that case you most likely need to do a full wipe, as well as formatting data,( the option were you have to type yes), in TWRP. The ROM works flawlessly on my phone. Good luck and insure that you have backed all your data first because this Will erase all data on internal storage.
Sent from my kltevzw using XDA Labs

it's possible to install Flyme OS 6 with CID 11?

Epiel said:
it's possible to install Flyme OS 6 with CID 11?
Click to expand...
Click to collapse
No because flume OS like all custom (roms, or most) require an unlocked bootloader. CID11 g900v can't be bootloader unlocked.
Sent from my kltevzw using XDA Labs

swiftbones74 said:
No because flume OS like all custom (roms, or most) require an unlocked bootloader. CID11 g900v can't be bootloader unlocked.
Sent from my kltevzw using XDA Labs
Click to expand...
Click to collapse
So sad to know it, thanks for helping me!

Oh man... I may have to knock my rust off and give this a go... Last chance to get up to a more recent security patch for my poor CID 11

( G900V+ CID 15 ) I want to install LineageOS after rooting, at which step i should flash the rom file and gapps file.. instead of the EMMC_15_VZW_QL1_MAGISK_ROOTED.zip... I just want to be sure

voldemort007 said:
( G900V+ CID 15 ) I want to install LineageOS after rooting, at which step i should flash the rom file and gapps file.. instead of the EMMC_15_VZW_QL1_MAGISK_ROOTED.zip... I just want to be sure
Click to expand...
Click to collapse
Just make sure that you have everything good and backed up. Do a full wipe in twrp / you may need to update twrp (klte version works for klrevzw now, as do klte aosp roms) flash rom gapps and root if you want it. / Reboot/ enjoy.
Sent from my PH-1 using XDA Labs

Anyone have any luck running Blackberry work with this magisk rom? I have apps hidden using magisk hide, Google play shows it is certified, but Blackberry work fails enrollment. On stock, it works fine. This is on a CID 15 phone.
Apparently Blackberry Work does more checks than google safety net and can detect modification. If anyone has any ideas how I can make Blackberry work think my phone is not modified, please let me know.
I've tried core only mode, hiding the app. What else can I try?

towel root
:trying to run towel root massage this phone isn't currently supported

Is compatible with xposed ?

The instructions worked like a charm on my EMMC 11. Props to the Op !
One question....looking to install AOKP or LineageOS which needs latest TWRP to install. How do I upgrade TWRP in Safestrap on the EMMC 11? I only see the new version for EMMC 15.
Thanks