Database Info

SOFT bRICKED. HELP

well i had trouble installing the trickroid v7 on my [S3] and it will say OS not installed.
then after many tries, of pulling the usb in and out and restarting several times to bootlocker
I cannot open to bootlocker anymore and the phone seems to died and not be able to charge.
WHEN I HOLD POWER button and volume down, all 3 soft touch keys lit up for 6~7 seconds, then the the black screen flashes a green line and off.
I cannot connect to the computer through usb either, for some reason.

i have the same problem.my phone worked fine, i unlocked bootloader, installed recovery and rooted. yesterday i put my phone on charging and today it was dead??? it flashes 7 times while holding vol down + power and then nothing happens.
EDIT:
i got it working!!! i connected it to pc, run adb command: adb reboot-bootloader and i got bootloader menu, after that i went into recovery and i did factory defaults and rebooted phone,now it's charging and everything is OK!

Bubach28 said:
i have the same problem.my phone worked fine, i unlocked bootloader, installed recovery and rooted. yesterday i put my phone on charging and today it was dead??? it flashes 7 times while holding vol down + power and then nothing happens.
EDIT:
i got it working!!! i connected it to pc, run adb command: adb reboot-bootloader and i got bootloader menu, after that i went into recovery and i did factory defaults and rebooted phone,now it's charging and everything is OK!
Click to expand...
Click to collapse
man.. i know i can fix it... but i cant connect to the damn pc. it unable to detect it... !!!

this is what i have done and got it working. connect phone to pc that has installed htc drivers, hold down volume down button + power, phone flashes 7 times and orange led is working now. after that go to adb, type adb devices and my phone serial number was shown. after that i did the adb reboot-bootloader and my phone was alive again.
p.s. i tried also with HTC One S All-In-One Toolkit V1.1,before i made it, to send command, but phone led only show orange light and again went off. u can give a try.... if that dont work, then i think phone is dead and ready for repair :/

Sony Xperia Z3 HARD BRICKED

Hi. My device is hardbricked. I see no lights while charging. Flashtool doesn't see my device.how can i fix this?
Edit:Easily fixed it.I plugged my device into the computer.I entered platform-tools and flashed boot.img.I saw "waiting for device" And i pressed volume up and power buttons. Suddenly boot flashed and i recovered my phone

You are very unlikely to have hard bricked it unless you have unlocked the boot and flashed something wrong.
If you did this please help us help you by telling us what you did just before this happened.
Also, just leave the phone on charge (Wall charger) for 24 hours and then see what happens.
In the mean time read this

solution for no LEDs no response no fastboot devices.
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.

Fastboot remote command not allowed SOLVED
stevenmanzano said:
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Click to expand...
Click to collapse
Hello
I had the same problem with REMOTE COMMAND NOT ALLOWED till i managed to solve it.
1st thing you need to clean that ANDROID folder you made on C: drive.Install all from the begining including flashtool.Boot windows to install unsigned drivers.In the flash tool folder youll find the driver downloader,just enable usb debugging and choose Mass Storage not MTP .; You have 4 options usb debug on/off and usb connectivity MTP or Mas Storage ;with every version selected connect and disconnect from pc with flashtool running.
When you use Fastboot start the flashtool and close it if it cant kill ADB (that assuming you succeeded in installing drivers).
Good Luck

Please tell me D6603 testpoint

bgbgtbvan said:
Please tell me D6603 testpoint
Click to expand...
Click to collapse
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54

john abruzzi said:
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
Click to expand...
Click to collapse
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??

mihir762000 said:
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
Click to expand...
Click to collapse
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.

Omario-242 said:
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Click to expand...
Click to collapse
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???

mihir762000 said:
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
Click to expand...
Click to collapse
The green led indicates flash mode so the problem is probably on your PC not detecting it properly. Does it show up in the system manager of windows if you plug it in at all? (Like a new device/android with a yellow triangle)
You could also try to fastboot a recovery and flashing a ROM from there. Not sure if it works but that's what I would try.

i m not even able to fastboot a recovery ...tried twrp and cwm both of them...

Me too

in my phone after charging 24h, only the red LED blinks, this is not normal any suggestions?
--------------edit
ok another week and still nothing
maybe I'll describe the problem:
I wanted to upload clean soft 5.1.1 and flash it
after the phone turned off it's start in recovery i used zip with SU and the phone turned off with no respond i try too reset (vol- + vol+ + power) but no reaction
there were no three vib
so I found that you have to reset the button under the sd flip
after this treatment you already know the charging of 3 days and only the red LED blinks
So any suggestions??
|

I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?

ibo90p said:
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
Click to expand...
Click to collapse
Like you I have a Xperia Z3 mines the 6633 variant.. Signs were showing it to be hard bricked, for example:
No led charge indication!
No power led!
No fastboot leds!
No USB detection sound when plugging into windows.
Literally a Z3 that was essentially a glass brick I bought off ebay for £6.50 GBP for spares/repair.
Since I had a bricked device, I had nothing to loose.
I applied heat to the rear glass with a hair drier & removed the panel, I removed the battery ribbon cable & plugged in via USB only to find the phone would show LEDs so put it on charge.
The Z3 now goes into flash mode, so then re-flashed a stock ROM from flashtool. I did a apps log & user data wipe, cust reset & fota reset.
To date I have no idea why the phone would not take a charge before or even detect via USB, though Id say give this method a go, you may be surprised!!
Good luck

Problems with my d6633 Z3 Dual

Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.

mazagi said:
Hallo people,
I have a very big problem with my d6633. I installed tonight TWRP - so fas, so good. After installing TWRP asked me to root the device, I said YES. My bootloader was unlocked. Then I couldn't exit TWRP. After every reboot the device started into TWRP. Now I can not start the device. I tried with Power+ Volume+, reset button - nothing.
Any suggestions?
Thanks for your help.
Click to expand...
Click to collapse
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you

yuzhengwen said:
Use flashtool go back stock, after flash twrp, flash supersu manually, don't let twrp install for you
Click to expand...
Click to collapse
How can I do that? There is no power on my device. And I think I cannot charge it...

mazagi said:
How can I do that? There is no power on my device. And I think I cannot charge it...
Click to expand...
Click to collapse
Google using flashtool to flash stock firmware

yuzhengwen said:
Google using flashtool to flash stock firmware
Click to expand...
Click to collapse
No chance. The device will not be detected. I can not charge it.

mazagi said:
No chance. The device will not be detected. I can not charge it.
Click to expand...
Click to collapse
How much % did it have before you started the procedure?
Did you try holding down vol+ and then plugging it into USB?

Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.

artusk01 said:
Hello Jkay7,
Thanks for your support. My solution was to leave the device switched off over the night. Connected via original cable. Today in the morning my dyouzhengwen evice was detected via flash tool and as youzhengwen suggested I could flash the original ftf file.
Click to expand...
Click to collapse
Nice to hear that!

Any help would be appreciated
Sony Xperia Z3 Dual D6633
I have tried just about every method seen. My problem with the flashtool or PC companion is that the phone is recognized by the computer but I can only start to turn the device on which I don't believe it actually boots. Broken display and new display does not power on.
Or it connects in fastboot by holding volume up when connecting. This shows a blue led.
But trying to connect in flash mode by holding power down just makes the led flash red then green continuously.
And for the pc companion it always says the connection was unsuccessful once the led turns green on the device.
I got the phone for only $40 in this condition. So I cannot say what entirely was wrong or what it's last working state was.
I bought a new screen and power flex cable. As well as a back plate and tempered glass protectors. I was going to wait until everything works perfect speakers and all before I sealed it tight with water proof adhesive stickers.
Even before I bought the new power flex the computer recognized it and the battery health and charge %. The battery was able to charge. But I couldn't turn the device on.
The computer confirmed that it had been at 29% after some time charging and then 100% after leaving it on charge.
Now with the new screen and power cable the phone still does nothing if not plugged it. The light was red at first, but then yellow, then after some time green when the battery fully charged. This was again even before the new parts.
I have to plug it in to try anything.
It goes red then starts to turn on and turns green.
But I hear no sound, get no vibrations, the computer only sees it as the phone and shows absolutely nothing on the removable disk. Just blank when I click on the drive volume. But it is seen as an Xperia D6633 phone or fastboot Android device.
I've tried the reset button, holding power and volume up, volume down, all three. Tried my factory cable. Different cables, different ports, uninstalling it from service manager and letting the flash tool recognize and install it.
I also tried the new display on the old power flex and the old display on the new power flex.
Nothing changed, no vibrations, no sounds, system never actually fully starts as far as I can tell, and cannot connect in flash mode only fast boot. And the flashable file is only seen in flash mode. Fastboot can only see the folder but it is ready to flash files as far as I can tell.

@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?

Jkay7 said:
@xdathekilljoy
That's a lot of money you're putting into an (apparently) broken phone Brave!
Okay so what happens if you hold Vol+ while it's shut down and then connect it to USB, the LED turns blue, right?
So why does flashing it from there on not work?
Click to expand...
Click to collapse
Well it didn't seem that broken at first and both it and the display were only about 37 piece. Power flex was almost 10. Seemed like a rightful price.
Yes the led turns blue and it is in fastboot mode. The flash file seems to only be readable for flashing in flash mode "volume down". I can see the folder of the flash file in fastboot mode " volume up ", but not in a flashable format.
And when connecting " volume down " it fails a connection while the led just flashes green to red to green to red continually

Two updates
1. I thought I should mention that when I do plug the phone in to a charger or computer the top does get a bit warm or hot as well as the led turns on. Different color depending.
2. With much fiddling and trying if holding the volume down button for different lengths of time while connecting up a computer I finally got it to connect in flash mode and flashed a file...... No change.
At this point maybe I should try a new battery for the hell of it even though this one seems to be working.
Or there is a minute hardware damage somewhere. Maybe the power ic? Or s capacitor?

Mate 8 bricked. Button combo's do nothing :(

I've foolishly tried coming back down from NXT-L29C636B585 ending up on NXT-L29C636B330 after using the roll back update mid-way. I then tried the roll back update again to then flash to NXT-L29C636B211 and now my phone does nothing but show the boot logo and get hot - which in this weather I could live without!
Power+up does nothing, power+down does nothing, and power+up+down also does nothing. I don't have TWRP on, and adb/fastboot commands do nothing as it can't get to recovery. I can't even turn it off!
Is it now a paperweight? The only way to turn it off is to let the battery run down I think as holding power down just makes it restart.

Confirmed - it only turns off if the battery runs out. On giving it charge it then pops up with the logo screen again, and again none of the buttons combinations do anything other than restart it. I think my only option now is to send it off to Huawei. Does anyone have any ideas other than having to send it off?

Did you connect it to a PC before trying power + volume down? Was the reason it didn't work for me before.

Yeah, hold Power + Volume down after connecting it to your computer via USB and you should see go into fastboot mode.

arvin2212 said:
Yeah, hold Power + Volume down after connecting it to your computer via USB and you should see go into fastboot mode.
Click to expand...
Click to collapse
I'll give it a go when I get home! god I hope this works..

YES! FASTBOOT! Only issue now is i'm FRP unlocked, but PHONE locked.. I can use the tool to unlock the phone as I have my password from Huawei, but what then? use the tool to flash one of the recoveries?
Thanks for the advice so far - I was very nearly physically sick when i realised nothing worked..

Try unlocking the bootloader and flashing twrp

bootloader unlocked and I used the SRK tool to flash stock 4.1 so now getting messages about my phone not being secure. Next step I figure is build enough charge in it to try flashing B330 again assuming power + vol up/down is working

bootloader unlocked. twrp 3.0.3 flashed ok:
C:\Program Files (x86)\Minimal ADB and Fastboot>fastboot flash recovery twrp.img
target reported max download size of 471859200 bytes
sending 'recovery' (23498 KB)...
OKAY [ 0.500s]
writing 'recovery'...
OKAY [ 0.330s]
finished. total time: 0.834s
However TWRP is nowhere to be found.. I just get the 'Your device has been unlocked' waffle and can't get to recovery still. Left the phone to fully discharge, and on inserting a mains lead to charge it for a while it then auto starts up and goes to the same screen - I try power&up and it just goes to the red charging 'lightning bolt' screen - then back to 'Your device' etc. I have no way of getting into TWRP!
I've been flashing Samsung phones for years and I can't remember ever getting this infuriated on a flash procedure..
I think I may have to do everything through fastboot as that's the only screen I can get to - but the only thing I can alter which seems to make a visible change is locking or unlocking the bootloader.
Should I re-lock with TWRP supposedly on? I have tried, and all I get is the 'not enough charge' screen - regardless of how long it is left untouched on power. It's as if all the charge I am putting in is just going to heating up the back and showing me the flipping message - then it runs low enough on charge to blank the screen, reboot and then end up with the unlock screen.
All I want to do is hold down all the buttons and have it install B211 - B330 - B'anything' from the dload folder on the sdcard I have in there. If anyone could tell me what to do to get to that point i'd be super happy. Failing that is there a way to fastboot flash a rom file?

Make sure to unplug the usb cable in order to get to TWRP.

malekowsky said:
Make sure to unplug the usb cable in order to get to TWRP.
Click to expand...
Click to collapse
At the moment i'm just struggling to get back to stock let alone a custom rom! If I ever get back to working phone in any way i'll be happy..
I've extracted out the boot, recovery and system from B330 and flashed them all through fastboot then re-locked the bootloader. It is still starting up with the Huawei logo as if booting up, and stays at that screen - It eventually then goes blank, pops up with the red circle with red charge pic in it, then after a while the Huawei logo reappears. I am essentially no further forward.
The more I flash things the more it pays no attention to me and sits on my work desk doing nothing.
I'm wondering if - in my epic screw-up - I managed to somehow destroy some part of the OS that governs charging, as it refuses to hold a charge while plugged in to the pc, powerbank or mains lead. At least thats what it is showing me.. It stayed powered long enough for me to fastboot flash the system.img, but that is when on the pc usb connection.
When I lock/unlock the bootloader through the SRK tool it finishes with the 'choose lock or unlock then press power' option which then promises a system reset.. and then it turns off with the red power screen. I can flash TWRP but because it is seeming not to hold a charge, I cannot then get into it without cables attached as it just boots back to the red charge screen.
Is there another file from the update.app I need to flash? should I just flash every single image and hope for the best? I really felt I was getting somewhere this afternoon..

Have you tried what I posted to you on?
https://forum.xda-developers.com/showthread.php?p=72758529#post72758529

Don Kronos said:
Have you tried what I posted to you on?
https://forum.xda-developers.com/showthread.php?p=72758529#post72758529
Click to expand...
Click to collapse
I plan to in the morning at work!

SOLVED: Phew - problem solved! see https://forum.xda-developers.com/mate-8/general/best-c636-rom-battery-life-t3623313#post72775720

Don Kronos said:
Have you tried what I posted to you on?
https://forum.xda-developers.com/showthread.php?p=72758529#post72758529
Click to expand...
Click to collapse
Hey,
I unbricked my phone using the same method - thanks for mentioning it! But sadly I'm stuck again. Maybe you have a hint for me?

Patneu said:
Hey,
I unbricked my phone using the same method - thanks for mentioning it! But sadly I'm stuck again. Maybe you have a hint for me?
Click to expand...
Click to collapse
Replied on that post! Probly not that useful though..

Xiaomi redmi S2 stuck in boot

Hello, today my xiaomi phone just stopped working. In the morning when i checked my phone it was all good, but then when i checked it like half an hour after, it wont unlock, i tried the power button, 2tap, fingerprint reader, nothing. My notification led was flashing as so i had some notofications so i knew it wasnt completely dead so i jsut hold power button to restart my phone. Now is where the trouble begins. It only shows "redmi" logo and wont start it got stuck in boot. I tried fastboot its changes to it but nothing can be done. I tried to hard reset it thru holding power button and volume button up together but it just restart again. I cant switch thw phone off nor i can switch it on it just loops there in boot and nothing can be done. So my question is is here someone who had similiar problem and fixit. If yes please tell me how.
Thank you all in advance.

1johny10 said:
Hello, today my xiaomi phone just stopped working. In the morning when i checked my phone it was all good, but then when i checked it like half an hour after, it wont unlock, i tried the power button, 2tap, fingerprint reader, nothing. My notification led was flashing as so i had some notofications so i knew it wasnt completely dead so i jsut hold power button to restart my phone. Now is where the trouble begins. It only shows "redmi" logo and wont start it got stuck in boot. I tried fastboot its changes to it but nothing can be done. I tried to hard reset it thru holding power button and volume button up together but it just restart again. I cant switch thw phone off nor i can switch it on it just loops there in boot and nothing can be done. So my question is is here someone who had similiar problem and fixit. If yes please tell me how.
Thank you all in advance.
Click to expand...
Click to collapse
Hi, I recommend you first of all back up your data if still possible.
Then, reboot into fastboot.
-fastboot erase system
- fastboot erase cache
- fastboot erase userdata
-fastboot erase recovery.
Then clean flash a rom.