Related
Yesterday i sent an email to huawei asking for the bootloader codes to my huawei g6-l11 and today they reply that they dont have the codes for this phone. Looked deeper into google and find out that dc unlocker already supports reading bootloader codes for this phone instantly
Here are the steps:
1. Download the last DC Unlocker Software
2. Install ADB drivers or Hisuite ( search forum )
3. Enable Manufacturer Mode, This is done by entering in dial pad code *#*#2846579#*#*, select "Project Menu", "Background settings", "USB ports settings", "Manufacturer mode".
4. Connect Phone to usb and open DC UNLOCKER
5. Open DC UNLOCKER and select Huawei Phones in manufacturer and leave the model Auto detect
6. Click on the magnifing glass and wait for detection
7. Voilá, the bootloader code appears in the BOX
8. Download Unlock Huawei Device GUI ( I cant leave links here but google is you friend )
9. Put the code generated by DC UNLOCKER in The field and click unlock
10. TADAAAAAAAA Unlocked Instantly
Remember, you can use this method to get the unlock code and you can use other methods to unlock the boot loader, just search the forum :good:
Not working for me:
DC - Unlocker 2 Client 1.00.1201
Detecting modem :
selection :
manufacturer - Huawei modems
model - Auto detect (recommended)
Found Applications port COM5
Found Diagnostics port COM4
Found USB interface {3F966BD9-FA04-4EC5-991C-D326973B5128}
Found modem : HUAWEI G6-L11
IMEI : 864037024395912
Firmware : 8226C00B109
SIM Lock status : unknown(read failed)
modem not found !
Click to expand...
Click to collapse
Diogo Glória said:
Yesterday i sent an email to huawei asking for the bootloader codes to my huawei g6-l11 and today they reply that they dont have the codes for this phone. Looked deeper into google and find out that dc unlocker already supports reading bootloader codes for this phone instantly
Here are the steps:
1. Download the last DC Unlocker Software
2. Install ADB drivers or Hisuite ( search forum )
3. Enable Manufacturer Mode, This is done by entering in dial pad code *#*#2846579#*#*, select "Project Menu", "Background settings", "USB ports settings", "Manufacturer mode".
4. Connect Phone to usb and open DC UNLOCKER
5. Open DC UNLOCKER and select Huawei Phones in manufacturer and leave the model Auto detect
6. Click on the magnifing glass and wait for detection
7. Voilá, the bootloader code appears in the BOX
8. Download Unlock Huawei Device GUI ( I cant leave links here but google is you friend )
9. Put the code generated by DC UNLOCKER in The field and click unlock
10. TADAAAAAAAA Unlocked Instantly
Remember, you can use this method to get the unlock code and you can use other methods to unlock the boot loader, just search the forum :good:
Click to expand...
Click to collapse
What phone model do you have???? Dont work in L11 LTE ...
I have the l11 4G LTE
Dont foget to enable manufacturer mode, it is necessary for qualcom phones
and make sure that you have the correct drivers
bugggmenot said:
Not working for me:
Click to expand...
Click to collapse
That is because you have modem in the field, you must select HUAWEI PHONE and not HUAWEI MODEM, hope it helps
Hi! I have the drivers, I try with debug mode on and off, I change the connection in engineering menu like you say, try all the usb types and nothing....
persona78 said:
Hi! I have the drivers, I try with debug mode on and off, I change the connection in engineering menu like you say, try all the usb types and nothing....
Click to expand...
Click to collapse
What error dc unlocker shows?
Thanks!!
Diogo Glória said:
What error dc unlocker shows?
Click to expand...
Click to collapse
no device.
but i think i need to reboot the phone when i choose Manufacturer mode, i dont try yet....
Do you have done any reboots?
Diogo Glória said:
Yesterday i sent an email to huawei asking for the bootloader codes to my huawei g6-l11 and today they reply that they dont have the codes for this phone. Looked deeper into google and find out that dc unlocker already supports reading bootloader codes for this phone instantly
Here are the steps:
1. Download the last DC Unlocker Software
2. Install ADB drivers or Hisuite ( search forum )
3. Enable Manufacturer Mode, This is done by entering in dial pad code *#*#2846579#*#*, select "Project Menu", "Background settings", "USB ports settings", "Manufacturer mode".
4. Connect Phone to usb and open DC UNLOCKER
5. Open DC UNLOCKER and select Huawei Phones in manufacturer and leave the model Auto detect
6. Click on the magnifing glass and wait for detection
7. Voilá, the bootloader code appears in the BOX
8. Download Unlock Huawei Device GUI ( I cant leave links here but google is you friend )
9. Put the code generated by DC UNLOCKER in The field and click unlock
10. TADAAAAAAAA Unlocked Instantly
Remember, you can use this method to get the unlock code and you can use other methods to unlock the boot loader, just search the forum :good:
Click to expand...
Click to collapse
When i open DC unlocker the Ports Section is always blank any solution?
Tutorial in next post works.
#HuaweiBootloaderUnlock
Hi! To Unlock the bootloader, first try this site, but if you don´t have you need to create a account ( free ):
https://emui.huawei.com/en/plugin.php?id=unlock&mod=detail
Insert your data like this example for U10:
http://postimg.org/image/6kddvoboj/
U10-G6, huawei G6-U10, etc..., DON´T WORK! Insert it like image shows.
Example for L11 model:
http://postimg.org/image/wha6ixm85/
Be sure from the data you are inserting...
If the Huawei site don´t work than try the next tutorial...
About the DC - Unlocker client and how to get the bootloader code.
It WORKS and i found how it works.
Here are the steps:
1. Need a internet connection and don´t use a proxy server, download DC-Unlocker but only this version works, install it and reboot :
https://mega.nz/#!ykxjiRia!ppWG22acgv35N5j1VMTsZlKMi0i0JQB9v8BVn5l98WI
DC-unlocker-client-software-V1_00_1201
2. Turn ON debug mode
Go to Settings -> About phone -> Press several times Build number it will say "you are a developer now" -> go back and open Developer options ->Turn ON USB debugging -> DONE
3. Install ADB drivers with Hisuite ( best way ):
http://consumer.huawei.com/minisite/HiSuite_en/
The first time HiSuite try to connect with the phone, in the screen phone it will pop up a Windows requesting permissions for the connection with PC, MUST GIVE IT!
4.With the phone >>>> UNPLUGED<<<<:
Enable USB Manufacturer Mode in phone:
In dial pad type code *#*#2846579#*#*
select "Project Menu"
"Background settings"
"USB ports settings"
"Manufacturer mode"
"CORFIRME"
5. Connect the Phone to usb, check if PC is installing the phone, wait to finish to install it. It will pop up a window in phone to choose connection, DON´T DO ANY THING, let it be like it is, in charge mode.
6. Execute, OPEN DC- UNLOCKER FOLDER A EXECUTE THE EXE FILE WITH ADMINISTRATIVE PRIVILEGES, DC UNLOCKER and Select Huawei Phones in manufacturer and leave the model in Auto detect
7. Click on the magnifing glass and wait for detection. Ignore any advise that you are using a old version of dc-unlocker, in new version to use this option you need to pay.
8. You will see the bootloader code appears in the BOX bellow.
9. Use this software and the unlock bootloader option, 18 option:
https://mega.nz/#!WgoVWLjQ
Key:
!YV1JLOGvXX4rvYreDXP1Twwh-V5O65NjmMxBH_7unUI
Read this- BOOTLOADER Unlocking-Relocking Procedure:
https://www.facebook.com/download/1560613864260023/BOOTLOADER Unlocking-Relocking Procedure.docx
If still don´t work, go here:
https://www.facebook.com/groups/huawei.g6.development/permalink/457458214413436/
Hi, thanks for this tutorial. I have followed these steps:
persona78 said:
Hi!
This is how i made it:
Here are the steps:
1. Download DC-Unlocker but only this version works, install it and reboot :
2. Turn ON debug mode
Go to Settings -> About phone -> Press several times Build number it will say "you are a developer now" -> go back and open Developer options ->Turn ON USB debugging -> DONE
3. Install ADB drivers with Hisuite ( best way ):
The first time HiSuite try to connect with the phone, in the screen phone it will pop up a Windows requesting permissions for the connection with PC, MUST GIVE IT!
4. It need to enable USB Manufacturer Mode in phone:
In dial pad type code *#*#2846579#*#*
select "Project Menu"
"Background settings"
"USB ports settings"
"Manufacturer mode" (IF OPEN THE MENU TO CHOOSE THE USB CONNECTION PRESS RETURN TO GO BACK TO CONFIRME)
"CORFIRME"
And Reboot the phone,.
5. Connect Phone to usb (MY DEBUG MODE WAS ON AND USB FLASH DRIVE WAS SELECTED) and open DC UNLOCKER.
6. Select Huawei Phones in manufacturer and leave the model Auto detect
7. Click on the magnifing glass and wait for detection
8. You will see the bootloader code appears in the BOX bellow.
Click to expand...
Click to collapse
In step 8, I get some information about my phone but the bootloader code is not there. All the information I get is the following:
selection :
manufacturer - Huawei phones
model - Auto detect (recommended)
Found Applications port COM5
Found Diagnostics port COM7
Found Phone : HUAWEIG6-L11
Model : Huawei Qualcomm Android phone
IMEI : XXXXXXXXXXXXXXX
Serial NR. : T7L7N1XXXXXXXXXX
Firmware : MSM8226C00B119_AMSS Sep 15 201410:04:11
Hardware ver. : HL1G6L22M
Wi-Fi MAC : XX:XX:XX:XX:XX:XX
BlueTooth MAC : XX:XX:XX:XX:XX:XX
SIM Lock status : unlocked
I suppose that the bootloader unlock code should be there but it is not. Is it possible that this method doesn't work for my phone? Or have I done something wrong?
Thanks for your help.
jjjuuann said:
Hi, thanks for this tutorial. I have followed these steps:
In step 8, I get some information about my phone but the bootloader code is not there. All the information I get is the following:
selection :
manufacturer - Huawei phones
model - Auto detect (recommended)
Found Applications port COM5
Found Diagnostics port COM7
Found Phone : HUAWEIG6-L11
Model : Huawei Qualcomm Android phone
IMEI : XXXXXXXXXXXXXXX
Serial NR. : T7L7N1XXXXXXXXXX
Firmware : MSM8226C00B119_AMSS Sep 15 201410:04:11
Hardware ver. : HL1G6L22M
Wi-Fi MAC : XX:XX:XX:XX:XX:XX
BlueTooth MAC : XX:XX:XX:XX:XX:XX
SIM Lock status : unlocked
I suppose that the bootloader unlock code should be there but it is not. Is it possible that this method doesn't work for my phone? Or have I done something wrong?
Thanks for your help.
Click to expand...
Click to collapse
Your DC-Unlocker is this version V1_00_1201????? Only this one shows the code, the new versions dont!
The link i post is for V1_00_1201 version, the only one that works on G6!
-----
F...k the download link for that version is not there any more.... I think i have it, i will upload and post it!
--------------
This is the right version
https://mega.nz/#!ykxjiRia!ppWG22acgv35N5j1VMTsZlKMi0i0JQB9v8BVn5l98WI
DC-unlocker-client-software-V1_00_1201
persona78 said:
Your DC-Unlocker is this version V1_00_1201????? Only this one shows the code, the new versions dont!
The link i post is for V1_00_1201 version, the only one that works on G6!
-----
F...k the download link for that version is not there any more.... I think i have it, i will upload and post it!
--------------
This is the right version
DC-unlocker-client-software-V1_00_1201
Click to expand...
Click to collapse
As you said, the problem was the version of DC-Unlocker (I was trying with version 1.00.1214).
I finally got my bootloader code with version 1.00.1201
Thank you very much for your help!!!
The new versions have that option to but need to activate the paid version... to many downloads made a opportunity for the creator, I think.
WOW finally it worked!! Tnx persona :X
notice that after installing HiSuit and ADB drivers, you need to recheck "Manufacturer mode" again. that was the part that took a lot of time for me to realize. even no restart needed!!
I had "Debug mode" on , Mass Storage and used DC Unlocker V1_00_1201 .
it seems DC Unlocker gets BL code frome a server, so make sure your anti virus allows DC Unlocker to connect.
Hi personna78
It doesn't work with my device.
I use dc-unlocker v1.00.1201
I use debug mode and usb flash drive
I use manufacturer mode
I get this answer:
Found phone : huawei g6-l11
IMEI : xxxx xxxx
Firmware : g6-l11v100r001c900b370
Device may be in wrote mode
Can you help me ?
sleo38 said:
Hi personna78
It doesn't work with my device.
I use dc-unlocker v1.00.1201
I use debug mode and usb flash drive
I use manufacturer mode
I get this answer:
Found phone : huawei g6-l11
IMEI : xxxx xxxx
Firmware : g6-l11v100r001c900b370
Device may be in wrote mode
Can you help me ?
Click to expand...
Click to collapse
Hmmmm, when you change to manufacture mode, confirm and don't reboot try dc unlocker than.
persona78 said:
Hmmmm, when you change to manufacture mode, confirm and don't reboot try dc unlocker than.
Click to expand...
Click to collapse
Hi personna78
OK, it is work non. Thank a lot
!Disclaimer: You will void your warranty by proceeding with this process! Make sure to check every step and backup your own data. I am not responsible for you soft or hard-bricking your phone. This tutorial is for the Honor 9 STF-L09C432B36(0/2/3/4/5/6/7/8). Other versions may work or may not!
Pre requirements:
-A working pc with internet connection
-your phone
-pin set in android (lock screen)
-USB type c connector
-read everything carefully
-proceed with caution
-rather ask, than doing something you don't understand or you are unsure of
Credits go to:
-xzx0O0
-topjohnwu
-k1ks
1.UNLOCKING THE BOOTLOADER
!If the phone perfoms a bootloader unlock, a factory reset will be perfomed automatically. So you will have to backup your data to a sdcard or to the pc.!
Step 1.1 and 1.4 are hanging together. They can be skipped with no worries, but I would recommend to do it. !THIS IS NOT A FULL BACKUP!
1.1 [OPTIONAL]BACKING UP PHONE SETTINGS:
1.1.1 Download and install Hisuite on your pc: http://consumer.huawei.com/minisite/HiSuite_en/
1.1.2 Connect your pc with your phone
1.1.3a If you see a pop up like this,then choose transfer files and skip Step 1.1.3b
1.1.3b Go to your Notifications on your phone. There will be a settings notification. Press on it and select File transfer via USB.
1.1.4 On your phone go to Settings -> Security & privacy -> More -> and turn on allow Hisuite to use HDB (image)
1.1.5 The phone may ask you to trust the pc. Select always trust this pc (image)
1.1.6 Go to settings -> System -> About phone -> and press about 10 times on the build number.
1.1.7 Go to settings -> System -> Developer Options -> and turn on USB debugging (image)
1.1.8 Open Hisuite on pc
1.1.9 Choose Backup and select everything. Don't password protect it.
1.2 OBTAINING THE UNLOCK CODE
Everything you see below in pink does not work anymore since Huawei has officially stopped providing the bootloader unlock code on their website.
Instead please use this thread for obtaining your bootloader unlock code: https://forum.xda-developers.com/honor-7x/how-to/how-to-unlock-huawei-bootloader-removal-t3780903
1.2.1 Go to this website and press Unlock
1.2.2 Register a huawei id or login
1.2.3 Follow the steps until you see this page
1.2.4 Choose Since Emui 5.0
1.2.5 Fill out the rest of the information. (The IMEI can be found at settings -> System -> About Phone)
1.2.6 Press Commit. If every info was put in correct, A yellow message should appear saying: "Your unlocking password is: ..." Copy the code somewhere safe on your pc.
1.3 UNLOCKING THE BOOTLOADER
1.3.1 Download Minimal ADB and fastboot for your operating system. For windows 32 and 64bit: https://androidfilehost.com/?fid=746010030569952951
1.3.2 install and open the folder where you installed it to.
1.3.3 Run fastboot.exe and adb.exe once
1.3.4 Go to Settings -> System -> developer options turn on OEM unlocking. If you do not have developer options do step 1.1.6 and come back to 1.3.4.
1.3.5 Connect your phone with the pc and turn on USB Debbuging(Step 1.1.7) and file transfer via adb(Step 1.1.3b) on your phone
1.3.6 On your pc go to the folder where you have installed adb. Open a CMD Windows at this folder(For Windows hold leftshift and press right click. Then choose open cmd from this folder)
1.3.7 Make sure that usb debugging is still enabled. In CMD: type adb devices -> hit enter. It should say your serial number with the status "device" (image)
If that is not the case, check if 1.USB Debugging is enabled 2. Allow Transfer files in Notifications.
1.3.8 type in CMD adb reboot bootloader. Your device will reboot into the bootloader.
1.3.9 It should say FRP Unlock and PHONE locked.
If FRP is locked and green, you did not enable oem unlock. => Hold the power button to reboot and go back to step 1.3.4
1.3.10 type in CMD fastboot oem unlock code replace code with the number from Step 1.2.6. Hit enter.
1.3.11 A window will pop up asking you if you want to unlock the bootloader. !Pressing yes will void your warranty and perform a factory reset deleting all personal data on internal storage.! With your volume up and down keys navigate to yes and press the power button to proceed. Your device will automatically reboot and perform a factory reset and reboot again.
1.3.12 Put in all your information, so that the phone is fully usable again
[OPTIONAL]1.4 REAPLYING PHONE SETTINGS
1.4.1 Repeat Step 1.1.2, 1.1.3, 1.1.4, 1.1.5, 1.1.6, 1.1.7 and 1.1.8
1.4.2 In Hisuite press restore and choose the backup you have created in Step 1.1.9
2.FLASHING AND SETTING UP TWRP
2.1 FLASHING TWRP
2.1.1 Set a pin for your phone if you have not (lockscreen). Go to this thread and download stf-twrp-zxz-0.3.img and this kernel
2.1.2 Move both .img to your folder, where you have installed adb
2.1.3 Do Step 1.3.5, 1.3.6, 1.3.7 and 1.3.8
2.1.4 It should say FRP Unlock and PHONE Unlocked(image) => Step 2.1.5 . If Phone is locked and green, you did not unlock your bootloader => Step 1.3.
2.1.5 in CMD type fastboot flash recovery_ramdisk stf-twrp-zxz-0.3.img => hit enter.
2.1.6 type fastboot reboot in CMD to reboot. Do not close CMD window and do not unplug phone from pc if you continue with 2.2.
2.2 SETTING UP TWRP
2.2.1 Do Step 1.3.5, 1.3.6, 1.3.7
2.2.2 in CMD type adb reboot recovery_ramdisk => hit enter
2.2.3 wait for it to boot. It will ask you for a password. You can choose whatever you want. I would recommend you use your PIN to unlock your phone. REMEMEBER IT!
2.2.4 Then this screen will appear. Swipe to allow modifications.
2.2.5 Press Reboot -> System and do not install the twrp app.
2.2.6a If your on screen buttons and flash are working skip step 2.2.6b
2.2.6b If your on screen buttons are not working => connect phone to pc and connect with adb correctly. In CMD press adb reboot bootloader to reboot into the bootloader. Then flash the custom kernel in CMD , by pressing fastboot flash kernel KERNEL_B360a_TOUCH_FIX.img and hit enter to flash. Then reboot your phone with fastboot reboot
2.2.7 !Read through this whole thread to check which functions of TWRP are working and which not!
3. ROOTING WITH MAGISK
3.1.1 Download Magisk v-16.0 from here and the uninstaller from here.
3.1.2 Connect phone with PC. Activate file transfer via USB in Notifications. Move the Magisk-v16.0.zip and uninstaller.zip to the root of your internal storage or sdcard on your phone.
3.1.3 Do Step 1.3.5, 1.3.6 and 1.3.7 . Type in cmd adb reboot recovery_ramdisk => hit enter.
3.1.2 Type in your password from Step 2.2.3. Press on Install. Select the storage where you put both .zip from Step 3.1.2. Search and press on Magisk-v16.0.zip. Swipe to flash. Then press on reboot to System.
Nice thread. Good.
If the site is long or bug at wish , do not answer for ask code.
Use a VPn or Proxy.
Hi,
is this guide still valid? I will get my phone next weekend. I cannot find "Unlock" at https://emui.huawei.com/.
Saftpresse99 said:
Hi,
is this guide still valid? I will get my phone next weekend. I cannot find "Unlock" at emui huawei com/.
Click to expand...
Click to collapse
I've tried to get the unlock code from the site for three days to no avail. It always just redirects to front page as there doesn't seem to be any unlock page anymore. So if anyone has any better luck with this please share
Saftpresse99 said:
Hi,
is this guide still valid? I will get my phone next weekend. I cannot find "Unlock" at https://emui.huawei.com/.
Click to expand...
Click to collapse
anon9000 said:
I've tried to get the unlock code from the site for three days to no avail. It always just redirects to front page as there doesn't seem to be any unlock page anymore. So if anyone has any better luck with this please share
Click to expand...
Click to collapse
I wrote an email to my regional Huawei Support, and they replied that if i sent them my model, IMEI etc, they will resend unlock code. So try this guys
Saftpresse99 said:
Hi,
is this guide still valid? I will get my phone next weekend. I cannot find "Unlock" at https://emui.huawei.com/.
Click to expand...
Click to collapse
Yes I'm sorry that I am replying so late.
So noone really knows if it is going to come back, but here's what you can do:
1: Go to this site. Scroll down. Choose your country. Call the hotline. Give them the required info. They will send you the unlock-code via Email. I tried it with the German Number and they send it to me without a problem.
2: Try emailing the support from Honor or Huawei.
3: Try out this Thread. You will have to pay about 4 EUR ($5).
Lukalion said:
Yes I'm sorry that I am replying so late.
So noone really knows if it is going to come back, but here's what you can do:
1: Go to this site. Scroll down. Choose your country. Call the hotline. Give them the required info. They will send you the unlock-code via Email. I tried it with the German Number and they send it to me without a problem.
2: Try emailing the support from Honor or Huawei.
3: Try out this Thread. You will have to pay about 4 EUR ($5).
Click to expand...
Click to collapse
How long did it take for you to get the unlock? I just called and they told me it should take about two weeks
shiboby said:
How long did it take for you to get the unlock? I just called and they told me it should take about two weeks
Click to expand...
Click to collapse
Try calling different phone numbers. Some are willing to give you the unlock and some not. I think they also don't know whats really going on with the site etc. But as of right now the 3 ways mentioned above, are the only ways to get the unlock code. Maybe the Unlock site at https://emui.huawei.com/ will come back some time.
Thank you for writing this tutorial, it's really helpful to have all steps in one place to know what to do.
If you could include how to revert back to the locked bootloader with stock firmware, that can be sent back to Huawei for warranty repairs, that would be great!
Best,
Chris
Hi
I did everything like in instructions and its gone well.
then i decided to install module in magisk to hide navigation bar and now my phone has a black screen and i can only turn it off... anyone knows how to fix it?
KubaEM said:
Hi
I did everything like in instructions and its gone well.
then i decided to install module in magisk to hide navigation bar and now my phone has a black screen and i can only turn it off... anyone knows how to fix it?
Click to expand...
Click to collapse
1. Go this thread and download the Mount-Magisk.zip
2. Move it somewhere to your phone. (If you are unable to boot to system connect phone to PC. Reboot phone to twrp. Open a adb window on the PC. In twrp go to advanced. Start the adb sideload. Press on cancel and then on back. Move the Mount-Magisk.zip into your adb folder on the pc. In the cmd type adb push Mount-Magisk.zip /external_sd or which ever path you like. )
3. Boot to twrp.
4. Go to Install and choose the Mount-Magisk.zip . Flash it. After flash press on back.
5. Go to Advanced -> File Manager. At the very top/root of your system should now be a folder called Magisk. Open the folder. The next folders also should include your Modules. Hold the folder of the module and delete it.
6. Reboot and everything should be fixed.
Let me know if it worked! :good:
Just to let everyone know. The unlock page is back. :highfive::laugh::laugh::laugh: Happy Unlocking :good::victory::victory::victory:
Lukalion said:
Just to let everyone know. The unlock page is back. :highfive::laugh::laugh::laugh: Happy Unlocking :good::victory::victory::victory:
Click to expand...
Click to collapse
Yeah... Its back for about 2 months, and then it will be closed pernamently
click
So if I unlock bootloader, and then root my device then i won't receive any OTA update anymore... but how can I deal with this situation in order to re-lock when it's OTA time and unlock again when I got it?
ps. No OTA means only no firmware or it means also no security patches ??
ov3rlordRAGE said:
So if I unlock bootloader, and then root my device then i won't receive any OTA update anymore... but how can I deal with this situation in order to re-lock when it's OTA time and unlock again when I got it?
ps. No OTA means only no firmware or it means also no security patches ??
Click to expand...
Click to collapse
In case of Honor devices, to a certain point you are still getting ota updates. To check on the newest updates download the app Huawei Firmware Finder. Then follow the HuRUpdate Thread to update to the newest firmware without unrooting.
hi, magisk automatically closes after about 3 seconds, how can I solve this problem?
listo09 said:
hi, magisk automatically closes after about 3 seconds, how can I solve this problem?
Click to expand...
Click to collapse
Try reflashing Magisk in TWRP.
listo09 said:
hi, magisk automatically closes after about 3 seconds, how can I solve this problem?
Click to expand...
Click to collapse
Issue Magisk FC , when you open Magisk , go direct on 'About' .
This will keep it open.
Some solutions should be on official section for Magisk
Lukalion said:
Try reflashing Magisk in TWRP.
Click to expand...
Click to collapse
Funziona, grazie
Hi! I'm currently attempting to complete step 2.1, but I've run into a problem.. I've completed all the 1.-steps and added the twrp & kernel img-files to the adb folder, but when I attempt to use cmd fastboot flash recovery_ramdisk stf-twrp-zxz-0.3.img, I just get the response waiting for any device, and then nothing else happens. Any suggestions?
(My first language is Spanish, I'm sorry if the translation is not perfect).
Device: Samsung Galaxy J7 (2016)
Model: SM-J7108
Firmware: J7108ZHU1APC3
TROUBLE:
I have a Samsung Galaxy J7 (2016) Duos, I thought it was SM-J7108, because in "Settings", the software version said "108", and behind the battery, it also said "108".
But when I was planning to update it to a new version of Android, I saw in the "Download Mode" that said model "SM-J7109", which caused me intrigue. I thought the device was actually "109" model, so I searched and downloaded the latest firmware of that model. And I proceeded to flash with Odin the firmware “J7109KEU1BRD1” of the "109" model.
When I turned on the device, I found the big problem that the device DIDN'T READ THE SIM CARDS of my country, it asked me for a SIM card from CHINA. Apparently the only firmwares for the "109" model were from China and there is no agreement with Google, so the device had NO GOOGLE APPs, nor Play Store. :crying:
I looked for solutions everywhere. And I never found a solution to return to the "108" model, it did not allow me to flash firmwares of the "108" model. I tried solutions for several days, until I succeeded in finding a new global firmware (J7109KEU1APC3) for the "109" model. I flashed it and fortunately it was perfect, without any of the above problems. :highfive:
SOLUTION:
Note:
· Make a backup of all your files because a factory restore will be done and everything will be deleted.
· Have “USB debugging” activated in the developer options. For this we go to "Settings - About the Device - Software Info" and repeatedly touch "Compilation Number" until the developer options are activated. We return to "Settings - Developer Options" and activate USB Debugging ”.
Required Files (download both on the pc):
· CROMService.apk
· Global New Firmware (J7109KEU1APC3)
Xda-Developers doesn't allow me to post links because I am a new user. You can find the apk and firmware easily if you google them. Otherwise, I can't think of any more solution that you write to my email "[email protected]" asking for the links with the title "Fix SM-J7109 Problems". (Only messages in english and spanish).
Steps:
1. Download the “CROMService.apk" and copy it to the device.
2. Install and open the app. A message will appear indicating an unlock.
3. Turn off the device.
4. Start “download mode” by pressing and holding the “Power, Volume Down and Home” buttons at the same time until a blue screen appears.
5. Press the “Volume up” button.
6. Open Odin on the PC.
8. Connect the device to the PC via USB cable.
9. In Odin it should appear colored blue in the “ID” box.
10. In Odin, click on “AP”, search and select the new global firmware (J7109KEU1APC3) that you downloaded on the pc. You need to select the ".tar" file. You have to extract the .rar file that you downloaded and you will get the .tar file. Then you select it in the "AP" box.
11. Go to the "Options" tab and make sure the "Re-Partition" box is empty. "Auto Reboot" and "F. Reset Time" are the only boxes that must be activated.
12. Go back to the "Log" tab and press "Start" and the new firmware will start flashing.
13. When finished, disconnect the cable. (The device will begin to loop without being able to turn on.)
14. Just remove the battery, and put it on again.
15. Start in "Recovery Mode" by pressing and holding the "Power, Volume Up and Home" buttons at the same time, until the samsung logo and text at the top comes out. Release and wait.
16. Using the “Volume Up and Volume Down” keys, move to and select “Wipe data / factory reset”, and then move and select “YES”.
17. Now move and select “Wipe cache partition”.
18. Now move and select “Reboot system now” and the device will turn on, without any SIM card problem and with all Google services and applications installed.
I hope it helps you and that you have been able to succeed by following the steps. Don't forget to click the "Thanks" button. :fingers-crossed:-Diego Rivera Campi-
play stor fixt room file
Hello, I did all the steps but I only get emergency calls and I am also from another country (Argentina) exactly the same thing happened to me as you. Now I definitely don't know what to do with my phone
Hello!
For all of PE-TL10 Honor 6 Plus people, this is a procedure I tried to unlock the bootloader.
As you know, you cannot anymore ask Huawei for the unlock code. If you like me are in this condition, try this procedure.
It is the same procedure you can find here: https://forum.xda-developers.com/p8lite/general/alternative-method-unlocking-bootloader-t3799294
with just a little edit for this device. So full credits must go to @@NayeBunny. Well done mate!
CAUTION: YOU WILL LOSE ALL OF DATA. DO A BACKUP FIRST!!!!
STEP 1 - Rollback
You need to be on Lollipop 5.1.1., EMUI 3.1. I tried this procedure in firmware B332.
If you are already on Marshmallow, EMUI 4.0, then do the following:
- go to https://www.hihonor.com/my/support/phones/honor6plus/
click on the choice menu "HONOR 6 Plus Dual SIM 3GB+32GB (PE-TL10)"
You will find 2 options which are equal. Choose the second one (will return more firmwares to download)
Click on Firmware Download
Download BOTH HONOR 6+ RollBack Package Android Marshmallow to Android Lollipop and HONOR 6 Plus Firmware (PE-TL10, Android 5.1.1, EMUI 3.1, C900B332, South Pacific, Channel-Others)
You will find instructions anyway the procedure is this:
- unpack the Rollback package and extract the UPDATE.APP file into a "dload" folder which must be in the root of your INTERNAL STORAGE (I have read various posts about putting it in the sdcard*, I put this in internal storage and worked)
* maybe because it is intended /sdcard/ , anyway not the external storage.
- turn off phone
- press vol+ vol- and power togheter (you can release power button when the Honor logo appears, but keep the volume buttons pressed until you get the EMUI update screen
When it's done, unpack the UPDATE.APP of the other package and put in the dload folder of the phone (of course delete the previous one!)
Do the force update procedure as before.
STEP 2: Root
We need to be rooted.
I used Kingroot for it: https://forum.xda-developers.com/devdb/project/dl/?id=29834
You can find instruction here: https://forum.xda-developers.com/android/apps-games/one-click-root-tool-android-2-x-5-0-t3107461
STEP 3: the magic code
Now we are all set up, you need to activate USB Debug first (or download a ADB package as in the first link I provided).
Just go to Settings - Phone info and click repeatedly on Series Number (the second line, below model number) until you get developer options turned on.
Go back, open Developer Options and turn USB Debug on. Authorize your computer when you connect the USB cable.
Now, do this:
Code:
adb shell
Then
Code:
su -c "grep -m1 -aoE 'WVLOCK.{14}[0-9]{16}' /dev/block/mmcblk0p6 |grep -aoE '[0-9]{16}'"
(here is the difference, the code info is in mmcblk0p6 in this phone)
If all goes well it will be returned a quite long number. Copy it.
Exit the shell (typing "exit", pressing CTRL+D...) and then
Code:
adb reboot bootloader
And finally
Code:
fastboot oem unlock ****************
in place of the stars paste the number you got.
I did this procedure and I unlocked my bootloader. Let me know if it works for you!
I hope this can help people to develop good ROMs for this great device!
Sorry for the necro.. but does this method works on Honor 6A Pro for unlocking the bootloader ?
shah22 said:
Sorry for the necro.. but does this method works on Honor 6A Pro for unlocking the bootloader ?
Click to expand...
Click to collapse
Hi,
no idea... just have a try!
As per original post, the procedure to unlock bootloader should be equal for the P8 and for other Huawei devices (like the PE-TL10): maybe just the location of the code info could be different (mmcblk0p6)
can some one provide the links for same device please?
PE-TL10 area c185I couldn't find no where!
osd_daedalus said:
Hello!
For all of PE-TL10 Honor 6 Plus people, this is a procedure I tried to unlock the bootloader.
As you know, you cannot anymore ask Huawei for the unlock code. If you like me are in this condition, try this procedure.
It is the same procedure you can find here: https://forum.xda-developers.com/p8lite/general/alternative-method-unlocking-bootloader-t3799294
with just a little edit for this device. So full credits must go to @@NayeBunny. Well done mate!
CAUTION: YOU WILL LOSE ALL OF DATA. DO A BACKUP FIRST!!!!
STEP 1 - Rollback
You need to be on Lollipop 5.1.1., EMUI 3.1. I tried this procedure in firmware B332.
If you are already on Marshmallow, EMUI 4.0, then do the following:
- go to https://www.hihonor.com/my/support/phones/honor6plus/
click on the choice menu "HONOR 6 Plus Dual SIM 3GB+32GB (PE-TL10)"
You will find 2 options which are equal. Choose the second one (will return more firmwares to download)
Click on Firmware Download
Download BOTH HONOR 6+ RollBack Package Android Marshmallow to Android Lollipop and HONOR 6 Plus Firmware (PE-TL10, Android 5.1.1, EMUI 3.1, C900B332, South Pacific, Channel-Others)
You will find instructions anyway the procedure is this:
- unpack the Rollback package and extract the UPDATE.APP file into a "dload" folder which must be in the root of your INTERNAL STORAGE (I have read various posts about putting it in the sdcard*, I put this in internal storage and worked)
* maybe because it is intended /sdcard/ , anyway not the external storage.
- turn off phone
- press vol+ vol- and power togheter (you can release power button when the Honor logo appears, but keep the volume buttons pressed until you get the EMUI update screen
When it's done, unpack the UPDATE.APP of the other package and put in the dload folder of the phone (of course delete the previous one!)
Do the force update procedure as before.
STEP 2: Root
We need to be rooted.
I used Kingroot for it: https://forum.xda-developers.com/devdb/project/dl/?id=29834
You can find instruction here: https://forum.xda-developers.com/android/apps-games/one-click-root-tool-android-2-x-5-0-t3107461
STEP 3: the magic code
Now we are all set up, you need to activate USB Debug first (or download a ADB package as in the first link I provided).
Just go to Settings - Phone info and click repeatedly on Series Number (the second line, below model number) until you get developer options turned on.
Go back, open Developer Options and turn USB Debug on. Authorize your computer when you connect the USB cable.
Now, do this:
Code:
adb shell
Then
Code:
su -c "grep -m1 -aoE 'WVLOCK.{14}[0-9]{16}' /dev/block/mmcblk0p6 |grep -aoE '[0-9]{16}'"
(here is the difference, the code info is in mmcblk0p6 in this phone)
If all goes well it will be returned a quite long number. Copy it.
Exit the shell (typing "exit", pressing CTRL+D...) and then
Code:
adb reboot bootloader
And finally
Code:
fastboot oem unlock ****************
in place of the stars paste the number you got.
I did this procedure and I unlocked my bootloader. Let me know if it works for you!
I hope this can help people to develop good ROMs for this great device!
Click to expand...
Click to collapse
It seems not working links anymore!
Hmmm...
Yes, I checked and those inks are linking elsewhere. Moreover, I can't find a mirror or another place hosting these files.
Sadly, I don't own amymore this phone and I deleted all of PE-TL10 files from my computer.
The only solution would be someone who downloaded these files, when they were available, to upload them somewhere.
My bad
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Team Win Recovery Project 3.x, or twrp3 for short, is a custom recovery built with ease of use and customization in mind. Its a fully touch driven user interface no more volume rocker or power buttons to mash. The GUI is also fully XML driven and completely theme-able. You can change just about every aspect of the look and feel.
This is a customised version of TWRP specifically for the Blackview BV9100!
Code:
#include <std_disclaimer.h>
/*
* Your warranty is now voided.
*
* I am not responsible for bricked devices, a meteorite crashing into your house,
* dead SD cards or thermonuclear war, YOU are choosing to make these modifications,
* and if you point the finger at me for messing up your device, I'll just ignore you.
*
*/
What works?
* Basic functions (Boot, Touch, ADB, Mount (internal/external), etc)
* Data decryption
What's broken?
* You tell me.
IMPORTANT - Disable dm-verity with the following fastboot command, or the recovery won't boot!
Make sure you use the vbmeta.img from stock rom!
Code:
fastboot flash --disable-verity --disable-verification vbmeta vbmeta.img
Downloads
Click here!
Device sources
Need help?
BV9100 Telegram Community
TWRP 3.5 - 28/02/2021
Download
Changelog:
Spoiler: Changelog
- Sync with latest TWRP changes
- Update encryption blobs
- Fix MicroSD/OTG mounting issue
Reserved #3
@bengris32
works but im unable to mount micro sd nor a usb stick in exfat nor making 2 partitions on one use (over 32gb) in 16k partitions less than 32 gigs.
may i ask how or where did you obtain the file?
mexamilian said:
@bengris32
works but im unable to mount micro sd nor a usb stick in exfat nor making 2 partitions on one use (over 32gb) in 16k partitions less than 32 gigs.
may i ask how or where did you obtain the file?
Click to expand...
Click to collapse
I didn't "obtain" the recovery, I made my own device trees for it, and built it from source.
As for the sdcard/usb mounting issue, I'll look into it.
@bengris32
Thanks for share
I noticed you are using BV9100_EEA_M860A_V1.0_20200430V19 in source files Where can i get BV9100 latest FW for non-EEA(non EU vs). Im on NON-EU version *NON-EEA* - notEU_BV9100_M860A_V1.0_20190910V2. Cant get my hands on their latest OTA updated FW. Maybe that's my problem? Does it even matter if its EEA on non EEA i mean they both run on same mk6765 platform.
There are 2 files i could find from official source, EU and non-EU versions, can be found here https://bbs.blackview.hk/viewtopic.php?t=532355 (version 20190910V2) kinda old but there is also the latest FW that goes OTA after u check for FW updates on bv9100. Blackview did not provide more recent updated one. Been working at it since Wednesday spending pretty much whole days figuring this out and back at it again atm
Not seeming to get this to work, but I'm not sure I know what I'm doing.
I took careful notes about what I did, anything look wrong wih the process?
First boot
► minimal set up then enable developer mode
(Settings 🞂 System 🞂 Advanced 🞂 About phone
▻ tap on "Build number" until unlocked, maybe 8 times
unlocks "Settings 🞂 System 🞂 Advanced 🞂 Developer options" menu
)
► In Developer options menu
▻ Select OEM unlocking (enter system password / pin)
▻ Turn on USB debugging (without cable attached)
► Connect USB cable
► On computer: "adb devices"
► On phone "Allow debugging" prompt comes up, allow it
► On computer: "adb devices"
▻ shows device "BV9100NEEA000..."
► Disconnect USB cable
► Power off phone
► Power on phone with volume down button pushed
► Connect USB cable
► On computer: "adb reboot bootloader"
► On computer: "fastboot devices"
▻ shows device "BV9100NEEA000..."
► On computer: "fastboot flashing unlock"
▻ computer shows "(bootloader) Start unlock flow"
▻ phone shows tiny text prompting for push volume up to allow
▻ push volume up
▻ computer shows "OKAY [ 23.545s]" (and some other stuff)
► On computer: "fastboot flash --disable-verity --disable-verification vbmeta vbmeta.img"
▻ using vbmeta.img from blackview forum link in post 6
▻ computer shows (about) OKAY ... sending ... OKAY ... writing ... OKAY
► On computer: "fastboot flash recovery recovery.img"
using recovery.img 3.4.0 linked from first post
▻ computer shows (about) OKAY ... writing ... OKAY
► On computer: "fastboot reboot"
▻ computer shows "rebooting..."
▻ phone shows tiny message about unlocked bootloader and delays boot 5 seconds
► Phone boots back into new system wizard
► Re-enable dev mode and reallow USB debugging
► On computer: "adb reboot recovery"
▻ seems to boot into an Android standard recovery, not TWRP
► Phone regular boot shows nothing different
neccowafer said:
Not seeming to get this to work, but I'm not sure I know what I'm doing.
Click to expand...
Click to collapse
What model of phone and FW are u running. I know u posted " BV9100NEEA000" but do u have the right FW on it that came witht he phone? There are 2 versions of this phone also FW files on official site are not updated to latest OTA update. Official FW for eu and non eu can be found here, but its old.
https://bbs.blackview.hk/viewtopic.php?t=532355 You can flash the older FW back and try again. If u have the original hardware FW on ur EU model phone then it could be possible for you
Ive made a post asking for the files, my message needs to be approved as a new registered user. You can bookmark the link below and wait for my post to appear and the files when and if they provide em.
official firmware - Page 2 - bbs.blackview.com
bbs.blackview.hk
Currently i reverted back to latest OTA stock FW till i get those new files.
I am at a standstill on the proper order to root and get twrp on this non eu model phone.
Magist guide says i need to flash to recovery partition (u need original to patch which i cant have without TWRP on the phone in the 1st place) Then there is another issue of getting TWRP onto the device before rooting which again u need the original vbmeta.img, i can do with a blank one but the problem comes to TWRP then setting an encrypted password provided by bengris32 which his twrp is for EU model of the phone. Headache
I'm on non EU FW, BV9100_M860A_v1.0_20200722V3
You can get SP Flash Tool thats needed to flash this phones FW, here https://spflashtool.com/ which has the latest version shown as V5.1924. There is also v5.2044 which i dont know how and where it came out, can be found here https://forum.hovatek.com/thread-13970.html @Hovatek seems reputable after me digging around for the past 3-4 days https://forum.xda-developers.com/m/hovatek.5636663/
Assuming you have MTK Drivers installed. if not https://forum.hovatek.com/thread-16640.html or find official site.
Open up SP Flash Tool,
Go to tab Download
Point Download Agent to where SP Flash Tool is installed to the file "MTK_AllInOne_DA.bin"
Load up you FWs scatter file in the 2nd box/line "Scatter-loading File.
***IMPORTANT! In the graph table below MAKE SURE U UNCHECK the preloader box. This will help getting TWRP as recovery later on.****
Klik box up top with green arrow that says "Download"
Phone is in off state.
Attach your USB cable to the phone, but NOT to the computer yet.
Hold VOLUME UP & DOWN at the same time then connect it to the PC.
On the SP Flash Tools you will see a long white bar on the bottom of the softwares window
It will turn RED then Yellow and will start flashing your phone.
You can RELEASE KEYS after you see the RED COLOR.
Once SP Flash Tools is done flashing a box will come up and say Done.
Close box, close SP Flash Tools.
Disconnect Phone from PC and Phone and u are on stock FW.
If u didnt uncheck the "preloader" box TWRP will not work on your phone
mexamilian said:
I'm on non EU FW, BV9100_M860A_v1.0_20200722V3
Click to expand...
Click to collapse
That's the same as mine: BV9100_M860A_V1.0_2020722V3, so I guess I'm waiting on BV to respond to your firmware update request.
neccowafer said:
Not seeming to get this to work, but I'm not sure I know what I'm doing.
I took careful notes about what I did, anything look wrong wih the process?
First boot
► minimal set up then enable developer mode
(Settings 🞂 System 🞂 Advanced 🞂 About phone
▻ tap on "Build number" until unlocked, maybe 8 times
unlocks "Settings 🞂 System 🞂 Advanced 🞂 Developer options" menu
)
► In Developer options menu
▻ Select OEM unlocking (enter system password / pin)
▻ Turn on USB debugging (without cable attached)
► Connect USB cable
► On computer: "adb devices"
► On phone "Allow debugging" prompt comes up, allow it
► On computer: "adb devices"
▻ shows device "BV9100NEEA000..."
► Disconnect USB cable
► Power off phone
► Power on phone with volume down button pushed
► Connect USB cable
► On computer: "adb reboot bootloader"
► On computer: "fastboot devices"
▻ shows device "BV9100NEEA000..."
► On computer: "fastboot flashing unlock"
▻ computer shows "(bootloader) Start unlock flow"
▻ phone shows tiny text prompting for push volume up to allow
▻ push volume up
▻ computer shows "OKAY [ 23.545s]" (and some other stuff)
► On computer: "fastboot flash --disable-verity --disable-verification vbmeta vbmeta.img"
▻ using vbmeta.img from blackview forum link in post 6
▻ computer shows (about) OKAY ... sending ... OKAY ... writing ... OKAY
► On computer: "fastboot flash recovery recovery.img"
using recovery.img 3.4.0 linked from first post
▻ computer shows (about) OKAY ... writing ... OKAY
► On computer: "fastboot reboot"
▻ computer shows "rebooting..."
▻ phone shows tiny message about unlocked bootloader and delays boot 5 seconds
► Phone boots back into new system wizard
► Re-enable dev mode and reallow USB debugging
► On computer: "adb reboot recovery"
▻ seems to boot into an Android standard recovery, not TWRP
► Phone regular boot shows nothing different
Click to expand...
Click to collapse
Hi, this is because android restores the original recovery when the device boots, you must not let your device boot into android until you boot TWRP for the first time, repeat all of your steps, but when you "fastboot reboot", hold the volume up button to access the boot menu, then select recovery mode. Once your device boots into TWRP, it will automatically patch the rom to prevent the original recovery from being restored on boot up.
bengris32 said:
Hi, this is because android restores the original recovery when the device boots, you must not let your device boot into android until you boot TWRP for the first time, repeat all of your steps, but when you "fastboot reboot", hold the volume up button to access the boot menu, then select recovery mode. Once your device boots into TWRP, it will automatically patch the rom to prevent the original recovery from being restored on boot up.
Click to expand...
Click to collapse
I confirm on my non EU bv9100 M860A
kept holding like you said then typed fastboot reboot and still held a selection menu popped up with 3 option on black background, i released the key then selected recovery, pressed the vol down to accept then quickly release it and went back to holding volume up and son of the devil it worked thanks, now i go back to messing with magisk installation.
Question though,
once booted into recovery following what u just said above, should vipe data factory be done like other (lineageOS) require or not? if it work it works just maybe thats where i had my issue with no mount for microsd and external
@neccowafer i can link you the official FW so u can flash what i have?
Latest stock rom link of BV9100 - bbs.blackview.com
bbs.blackview.hk
get the non-EEA version and flash it follow your own steps you mentioned
EDIT: Just did wipe data button bottom right on button [WIPE] then did factory wipe.
How access to internal and MTP on reboot into recovery with buttons, still can get micro sd mount
Got a reply from official blackview admin
official firmware - Page 2 - bbs.blackview.com
bbs.blackview.hk
looks like there wont be any updates to A10 and over. Gonna be trying out different CFW and see how it does, i managed to get unofficial lineage-17.1-20201215 unofficial with test keys flashed
I just got one of these phones today and I'm having a bear of a time getting into it with adb to install TWRP and hopefully flash a new ROM. I tried to follow the detailed instructions from neccowafer (thank you for those!) earlier in this thread, but adb returns the device as unauthorized when in recovery mode.
This phone seems to have two recovery modes. One is accessed by booting while holding vol-down and the other is loaded when you boot holding vol-up and choose recovery from the menu.
In either recovery mode, I run adb devices and get
List of devices attached
BV9100EEA00016800 unauthorized
While booted to Android, I run adb devices and get
List of devices attached
BV9100EEA00016800 device
I'm becoming a bit frustrated trying to figure it out on my own, and it's been a few years since I did any custom bootloader or custom ROM stuff with Android, so any help would be very much appreciated.
@JeffJK I have factory mode on my down key and recovery mode on up, you wanna do up. my model is NEEA
mexamilian said:
@JeffJK I have factory mode on my down key and recovery mode on up, you wanna do up. my model is NEEA
Click to expand...
Click to collapse
Oh good to know! I got the same error noted above in the up key mode, the unauthorized thing from adb. Any idea why?
did u enable dev mode then enabled usb debugging, boot loader unlocked?
when u got ur phone out of the box, skip everything and dont sim in, just skip things, make sure u dont set any pass and dont encrypt device, enable dev mode then enable debugging by tapping on ur build in settings all the way on bottom in about. make sure oem unlock is also enabled and greyed out if u done already so.
mexamilian said:
did u enable dev mode then enabled usb debugging, boot loader unlocked?
when u got ur phone out of the box, skip everything and dont sim in, just skip things, make sure u dont set any pass and dont encrypt device, enable dev mode then enable debugging by tapping on ur build in settings all the way on bottom in about. make sure oem unlock is also enabled and greyed out if u done already so.
Click to expand...
Click to collapse
Ah, I did set the phone up. Should I wipe and start over?
EDIT: I did a factory reset and booted into Android to turn on debugging, and even without setting up anything on the phone, encryption was enabled in the security settings and adb still lists the device as unauthorized while in recovery mode.
EDIT 2: Also tried wiping /data from the recovery mode menu, which put out the below lines but still did not allow adb access even after a kill-server
Code:
Formatting /data. . .
Formatting /cache. . .
Formatting /mnt/vendor/nvdata. . .
Data wipe complete.
@JeffJK To remove encryption meaning you had twrp installed and made it work or stock os?
Boot into recovery Format data / factory reset This will remove encryption and delete all files stored in the internal storage, as well as format your cache partition (if you have one).
*DONT set any passwords for lockscreen, dont login to google, pay attention to not encrypt device when setting up. just basic skip u dont even need wifi or sim in phone
Dont forget to unlock ur bootloader before flashing or doing anything. Follow post #7 thats exactly how you would do it then read up on post #10 and #11 and it will work.
Also did you install USB drivers?
Get android usb drivers https://developer.android.com/studio/run/win-usb
if that didnt work try the one below,
https://forum.hovatek.com/thread-16640.html (need to register) you want the " Auto Mediatek USB VCOM Drivers Signed"
If you messed up you just flash your legit FW back to stock and follow post #7 10 and 11
mexamilian said:
@JeffJK To remove encryption meaning you had twrp installed and made it work or stock os?
Boot into recovery Format data / factory reset This will remove encryption and delete all files stored in the internal storage, as well as format your cache partition (if you have one).
*DONT set any passwords for lockscreen, dont login to google, pay attention to not encrypt device when setting up. just basic skip u dont even need wifi or sim in phone
Dont forget to unlock ur bootloader before flashing or doing anything. Follow post #7 thats exactly how you would do it then read up on post #10 and #11 and it will work.
Also did you install USB drivers?
Get android usb drivers https://developer.android.com/studio/run/win-usb
if that didnt work try the one below,
https://forum.hovatek.com/thread-16640.html (need to register) you want the " Auto Mediatek USB VCOM Drivers Signed"
If you messed up you just flash your legit FW back to stock and follow post #7 10 and 11
Click to expand...
Click to collapse
I couldn't get TWRP because adb still reads the device as unauthorized. I wiped the data while in recovery mode, booted to the"Welcome" screen, and when I skipped everything in the setup wizard, the settings still show encryption as enabled, and I had no option to enable or disable it at any point. Bootloader also still showed as unlocked. This seems like a very unusual problem! I have drivers but will try the vcom ones.
if u are able to get into adb and fastboot then u dont need the VCOM drivers.
On device use "Revoke USB debugging authorizations" in "Developer Options"
then reconnect to phone to cable then pc
@JeffJK
Would you do me a favor, my current connected device sn is 123456789ABCDEF.
I messed up with flashing some roms and wiped the nvnand partition without making a backup of official stock one( didnt know about nvnand till issues started happening), been working on fixing S/N and device connected via adb to stock, currently have tee key and google key in red as overlay, i know ways of getting rid of it but id rather have the original back.
need some structural info, you can replace last 5 number from your serial with XXXXX if u want. i have some files i managed to scrape up digging around on how tos, just clueless on how to get tee key/google key and serial back onto device with proper format.
go into your phones setting>system>advanced>About phone. Post what what you see in the following:
*SIM Status (sim slot 1) klik on in and scroll down to EID (mine says unknown) and post (hide last 4 or so numbers but include full length) i will need to know what to look for when flashing mine back to my phones original status
*Model & Hardware klik on it my says for Model: BV9100 Serial number says 0123456789ABCDEF (again hide last 4 or 5 so i have an idea of what i need to look for in my files)
*WI-Fi MAC address and Bluetooth address all i need from this is do they match or are different, also post last 2 digits/bits in wifi and bt addresses ( i need this for to figure if multicast)
I REALLY RECOMMEND you write this info down before messing with roms and flashing or ull end up like me with blank IMEI (managed to flash fix it), serial of 123456789ABCEDF(still cant fix), and a permanent tee key google key in red(still cant perma fix, have to always remove factorymode). you can watch tutorials on how to use "Mtk Droid Tool to backup your nvnand IMEI serial, make a scatter file on updated OTA latest update of stock BV9100 rom (its really well optimized after trying Lineage unofficial 17.1, HavokOS 3.12 (I have files and sources)
I do not know where the official source for MTK DROID TOOLS is (the latest version i have found is Mtk_Droid_Tool_v2.5.3B some say 2.5.3 I have both if needed source to https://forum.hovatek.com/thread-15665.html) (bitdefender total security says clean on my pc before i installed, it does run sluggish on 10850k with 128gigs ram on nvme) I do recommend u scan with your AV and upload it also to https://www.virustotal.com/gui/ and any other files you get just do be safe
Heres a little write up on how to do so as i cannot cause my phone doesnt have proper setup on stock after a mess up
"
Requirement : Your Google android device should be rooted.(Officially provided with source if u need, DONT root it via the mtk droid tools, there is an option. Go with magisk official https://github.com/topjohnwu/Magisk/releases/tag/v21.2 After you have TWRP installed from this thread, download the 21.2 magisk zip file and install inside twrp reboot and configure it)
Download and open MTK droid tools application.
Enable USB debugging mode on your device. Settings > Developer Option > Click USB debugging mode.
SKIP THIS UNLESS YOU HAVE ISSUES(let me know)Then connect your android smartphone to the computer. Your device will detect by MTK droid tools within few minutes. If your mobile phone is not detected, then you have to install USB drivers on your device first. Right click on the “InstallDriver.exe” and select “Run As Administrator” and then restart your computer to install USB driver.
Click IMEI/NVRAM to backup android IMEI and then click backup. Your android backup will be stored in BackupNVRAM folder.
Continue to the backup system, firmware, data and etc (Android ROM) select on Root, backup, recovery tab and backup tab. The process will finish within few minutes.
"