Related
Hello,
I just bought a touch screen for diamond and i am wondering to know if i can replace it without replace the lcd screen!!!
ferrari373 said:
Hello,
I just bought a touch screen for diamond and i am wondering to know if i can replace it without replace the lcd screen!!!
Click to expand...
Click to collapse
I have replaced several screens on Touch Diamonds, however the LCD matrix appears to actually be stuck onto the digitiser and the LCD itself is very very fragile. I usually replace the whole unit (LCD screen and digitiser) because it is much easier. You can purchase these from various sellers in Hong Kong on Ebay.
I have allready bought a touch screen but not the lcd screen!!! Do u have a guide or something that shows how to change it???
ferrari373 said:
I have allready bought a touch screen but not the lcd screen!!! Do u have a guide or something that shows how to change it???
Click to expand...
Click to collapse
My recommendation would be to re-sell the touch screen and buy yourself a complete LCD & digitiser module. It is much much easier to do. In terms of taking the phone apart, it is fairly straight forward. Be careful with the small co-axial cables inside though, because they are easily damaged and difficult to obtain without replacing the antenna board. Re-connecting the ribbon cables can also be a bit fiddly.
The LCD and digitiser are glued into the front of the phone. You will need to disassemble the phone and then very carefully using a plastic flat blade, ease the LCD out of the front of the phone housing. It will come out with a little bit of care. There should be enough glue remaining in the housing to re-seat the replacement unit and hold it in place.
If you google you should be able to find the HTC Diamond service manual which tells you how to take the phone apart and re-assemble it. I have a copy, so if you can't track it down, PM and I will e-mail it to you.
Andy
Hi,
To barncourt, how is the build quality of those honk kong made screens?
also a lot of the screen+digitizer that i have seen on ebay all have the front facing camera. would it be possible to use that screen even though my diamond is the one that has no front facing camera?
Of course, it is just a hole
p.brazauskas said:
Hi,
To barncourt, how is the build quality of those honk kong made screens?
Click to expand...
Click to collapse
Okay, but I tend to buy from the same seller. Not had any particular problems.
barncourt said:
Okay, but I tend to buy from the same seller. Not had any particular problems.
Click to expand...
Click to collapse
Hi I wanna know can you share your supplier adress with us ?
I'm looking for a LCD+digitizer and what I see is not something giving confidence...
So if you can give us some real-tested place to start...
Also I've dismantle the phone but it's quite hard to take the screen+digitizer away...
it's seems completely fixed with the housing does some one got s pics or guide on how to dismantle and replace the screen
(The HTC service guide you can see here and there just don't deal with the screen.)
and when I started just broke my screen (which was already broken anyway so...)
http://www.fuelip.com/howto/diamondlcd/diamondlcd.htm
I followed that guide and replaced my screen. I have one last problem though - I can't fit back my power button. It's made of two parts the black plastic cover and the transparent rubber. How do you stick them together? I'ts funny that I took my whole diamond apart with all the cables and boards and now I can not figure out how to fix a silly button
Hi all,
I sat on my Fuze, short and simple. There is now a weird crack on the screen. I am very familiar with what a broken LCD looks like, there is no LCD "liquid" oozing all over the place, and the picture is not distorted in any way. It looks like some kind of lens INSIDE might be broken, and I think it's the digitizer. The cracks stop once they get to the dark grey at&t/HTC border around the screen, even though I hit very close to it, so whatever I cracked is under the top lens/protector.
Also, I read online (albeit at a cell phone repair website) that you can't replace the digitizer without ruining the LCD. Is there any merit to this, or are they just trying to convince people to pay their obscene $149 to replace a $30 part?
So I guess I have two questions:
Did I break the digitizer, the topmost lens, or somehow the LCD glass without damaging the LCD itself?
How hard is this to replace?
Pics:
EDIT: I ordered this on April 17th. Fat chance AT&T will do anything about it, right?
That looks like just the digitizer... I purchased the digitizer already, but haven't gotten the chance to take it apart yet.... to be honest I'm very nervous about taking it apart.. I'm still trying to figure out how to split the two pieces apart (the keyboardbase and the slide screen....
wxy117 said:
That looks like just the digitizer... I purchased the digitizer already, but haven't gotten the chance to take it apart yet.... to be honest I'm very nervous about taking it apart.. I'm still trying to figure out how to split the two pieces apart (the keyboardbase and the slide screen....
Click to expand...
Click to collapse
If I'm not mistaken (and I might be), all this should take is removing the two small phillips head screws on the back of the screen that show when the phone is slid open. I landed on this thing while it was open, and drove my knee right into the screen, I'm surprised I didn't break anything else.
There are three more screws that you can't see behind the screen.... when its slid open you can only see 2 screws... There are actually 5
wxy117 said:
There are three more screws that you can't see behind the screen.... when its slid open you can only see 2 screws... There are actually 5
Click to expand...
Click to collapse
So we do have to take the whole damn thing apart?
Does anyone have any luck with AT&T replacing things that are clearly accidental damage? With all the horror stories I hear about refurbished phones and the chance that they might send me one, I'd actually rather take my chances at fixing this. I've taken apart a ton of phones and fixed them before, and worked at a cell phone repair shop for a few months. I still have most of my tools lying around, including all the screw drivers I'd need to open this.
I was able to find an HTC service manual that doesn't really explain how to replace the digitizer. It does describe how to get it in two pieces, but I wouldn't know where to go from there.
I have the digitizer in my hand... There is a thing that hooks up to the phone itself so yes i'm pretty sure you have to take apart the entire thing.... I think i'm gonna take the phone to NYC and have someone that knows what they're doing repair it. I tried to get warrenty repair, but they said no because it is accidental damage. i pretty much tried everything before I ordered a new screen.
wxy117 said:
I have the digitizer in my hand... There is a thing that hooks up to the phone itself so yes i'm pretty sure you have to take apart the entire thing.... I think i'm gonna take the phone to NYC and have someone that knows what they're doing repair it. I tried to get warrenty repair, but they said no because it is accidental damage. i pretty much tried everything before I ordered a new screen.
Click to expand...
Click to collapse
Found a good complete disassembly guide in Russian, why does the screen have to be the LAST thing to come out? I am now looking to buy an LCD/digitizer combo, but I can only find the one from Brando that is made for regular HTC Touch Pros, and not the Fuze (has a camera cutout instead of the AT&T logo).
If I end up having to replace the LCD I'd much rather break it trying to save $50 than just toss it. Is it really that hard to separate the digitizer from the LCD?
http://translate.google.com/transla...ka/htc-touch-pro/&sl=ru&tl=en&history_state0=
has anyone had success separating the Digitizer and the LCD screen?
wxy117 said:
has anyone had success separating the Digitizer and the LCD screen?
Click to expand...
Click to collapse
Well, we'll find out. I ordered both an AT&T Fuze digitizer by itself as well as an LCD with a digitizer attached. I'm just going to go ahead and replace everything with the combination unit and see if I can replace my broken digitizer without breaking my LCD in my free time. If it works, I have a spare or I can sell it
be careful I got my digitizer and they sent me the wrong one. They sent me one for a sprint touch pro....
wxy117 said:
be careful I got my digitizer and they sent me the wrong one. They sent me one for a sprint touch pro....
Click to expand...
Click to collapse
Hopefully I'll get it right, I made sure to order an AT&T Fuze digitizer that made it clear it wasn't for use with Sprint Touch Pros or Touch Pros with front facing camera.
The LCD+digitizer I ordered though may very well show up as any of the above, if they're not already attached I'm going to use the AT&T Fuze digitizer on the new LCD, and try and make a new working combo from my old LCD to resell. I'll make a detailed step by step with photos as well.
Don't forget to read this
They just sent out my new one today.... So anyone that needs a digitizer for the Fuze by Sprint hit me up.... They told me to keep it so now I have an extra digitizer that doesn't work for my phone...
I think I can help you cos I repaired LCD and digitizer on Raphael a week ago. Digitizer and LCD are two separate parts joined by flat printed wires. If you need to change just one of them you will need to take apart whole phone.
Raphael consists from 2 main parts - 1. that one with keyboard 2nd part with LCD. You have to take apart both what is quite hard to realize if you this for the first time.
Once you are with your LCD you will see the flat wires grom lcd and digitizer meerged. Split them with your solddering gun carefully! Take new digitizer and solder flat wires together. Anyway there is no glue or liquid fluit or whatever between digitizer and LCD. But - remeber especially those who replacing just LCD - there is kind of black tape around the backside of LCD part (the silver side) - take it apart from old lcd and move to new one. If you dont you will see the rainbow on your LCD but just after assembling whole device together - it is quite concerning if you find out this kinf of malfunction just after such a hard work like a assembling this hellmade device
Good luck to everyone!
pisqle said:
I think I can help you cos I repaired LCD and digitizer on Raphael a week ago. Digitizer and LCD are two separate parts joined by flat printed wires. If you need to change just one of them you will need to take apart whole phone.
Raphael consists from 2 main parts - 1. that one with keyboard 2nd part with LCD. You have to take apart both what is quite hard to realize if you this for the first time.
Once you are with your LCD you will see the flat wires grom lcd and digitizer meerged. Split them with your solddering gun carefully! Take new digitizer and solder flat wires together. Anyway there is no glue or liquid fluit or whatever between digitizer and LCD. But - remeber especially those who replacing just LCD - there is kind of black tape around the backside of LCD part (the silver side) - take it apart from old lcd and move to new one. If you dont you will see the rainbow on your LCD but just after assembling whole device together - it is quite concerning if you find out this kinf of malfunction just after such a hard work like a assembling this hellmade device
Good luck to everyone!
Click to expand...
Click to collapse
Thank you for some rather broken, but very helpful advice. Kinda sucks that I'm really happy since I don't have to worry about removing any adhesive, but now I have to sit here and solder flex cables. I shoulda bought a spare one
Do they ship these parts on pigeons from Hong Kong?
To anyone counting on being able to separate the LCD from the digitizer, DON'T. There is absolutely no way to separate them without destroying either or both. Also, take extreme caution when peeling up the flex cable, it is very easy to tear (I tore mine).
So my net cost, 80 + 50, LCD/Digitizer and Flex Cable = $130 vs. sending it to HTC $150. I advise anyone to just pay them rather than take this thing apart.
from my understanding people have done it before... Maybe you just had bad luck? Well we'll see when my screen comes in *crossing fingers*
wxy117 said:
from my understanding people have done it before... Maybe you just had bad luck? Well we'll see when my screen comes in *crossing fingers*
Click to expand...
Click to collapse
Fact of the matter is when people say this is a delicate phone to take apart, they mean it. I worked at a cell phone repair store for a few weeks, and learned how to take apart damn near anything (thank God this was before the iPhone existed). Not only are both flex cables in this phone taped down in 100 different places, making them very easy to tear while removing the tape, the adhesive used between the LCD and digitizer is STRONG. If you really wanted to separate them, you might have some luck with a straight edge and maybe an hour. Good luck, I'll let you all know how this turns out once I have my new flex cable, since I conveniently tore the volume buttons off the original.
I just got my screen today so we're gonna see some time next week how we do on this screen replacement....I'll let you know how it goes....
So far no luck with my digitizer. Has anyone had any luck just changing out the digitizer yet? The guy that was suppose to do mine is backing out because he doesn't want to risk cracking my LCD. I don't blame him thats the reason I didn't do it. sheik124 what are you doing with your damaged fuze? Are you sending it to HTC for repairs?
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Report it broken, pay $90 for a replacement through Asurion. Cheaper than $500, y'know?
Sent from my FroyoEris
You need to google for a eris digitizer.
LMGTFY
http://www.google.com/search?hl=en&...fai=CMBq5koWzTNrsN46EygTEha3rCQAAAKoEBU_Q0wbi
i think u can get them for like 40+ dollars off ebay
If you don't mind the long shipping times, you can get a digitizer + the entire housing together for around $60 on ebay. Doesn't seem like a bad deal to me.
#EDIT#
Zombie post . . . sorry about that. Need to remember to look at dates before replying.
Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I just replace mine, and is wasn't too bad. There is videos on YouTube about how to do it. It took me about an hour, and the part costs about 40 bucks. If you need any help with it, feel free to email me [email protected]
Aaron
you can get one @ 49usd
http://www.htcrepairparts.com/touch-screen-digitizer-for-htc-g5-eris-p-2727.html
Palmbxr said:
so i dropped my phone just the outer glass broke the lcd is find i was wondering where i can get the cheepest replacement for that i realy dont know what the price goes for but id rather not spend 500 on a retail andriod phone. my upgrade is like 3 months
Click to expand...
Click to collapse
I'm going through the same thing. Amazon has some digitizers for about $40. I decided to spend the extra $20 and get this instead
http://www.amazon.com/gp/product/B004F5CEDW
It's the whole casing. I didn't want to bother with stripping the digitzer off the frame which is glued on. With replacing the whole body, you just move the mainboard over and plug everything back in. At least this is my hope. I'll post here again when the thing actually arrives. I ordered it two weeks ago and it probably won't be here until mid March.
Good luck with whatever you decided to go with.
UPDATE. hmmm october was the post date. I guess this guy has long taken care of his problem
Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.
roscuthiii said:
Are there any particular tools needed? I swear my other half is on a mission to destroy her phone. It'd be good to know how to do some of the possible DIY stuff.
Click to expand...
Click to collapse
There's Youtube videos for disassembly. I haven't watched them myself, but I know they exist, so they probably tell you what tools you need there. From what I remember hearing, just some small torx screwdrivers, or maybe some small phillips, too, but don't quote me on those.
Here is a link to the teardown video I followed.
http://www.youtube.com/watch?v=zHwm-32BI0w
The amazon link in my previous post is what I bought. It was the whole body. There are just screen replacements but I didn't want to mess with that because the digitizer is glued to the front piece. I didn't want to risk warping or breaking the front piece and completely screwing myself over. Anyway, what I bought came with the tools you need to perform the teardown and an extra screwdriver that was not needed.
I am glad I did this. However, it came with it's share of issues.
-The very top of my digitizer does not work. As a result, I can't pull down the notification bar. I can get to it through the menu button but it is annoying.
-I had to move the ear speaker and loudspeaker over. They were glued to some foam which was stuck/glued to the chassis. That foam absorbed the vibration. When my phone rings loud it is nasty because the speaker is bouncing around. I tried to cut some foam myself to replace what was stuck in the old case. It helped but it's not perfect.
-There are some rubber buffers? Isolators? Not sure what their called which also needed to be moved over form the old case.
-It took a month to ship to my house. After discovering these issues, I am kind've stuck with them because it would take a month to send the parts back and another month to get a replacement. By then I'll be due for a new phone.
So that's my experience of replacing the whole case.
Let me know if you have anymore questions.
Thanks for sharing your experience!
My pleasure. Glad to help out.
Sent from my Eris using XDA App
To add to this, because I'm sure there are others out there like me who intend to use their Eris until it gets run over, dropped in lava, drawn, quartered, and defecated upon . . .
I ordered the same replacement housing and digitizer as mentioned above, and had 2 small problems:
The housing I got had a nut in it that came loose, so that one of the corners wasn't able to reassemble properly.
There was something different in the new housing that caused the proximity sensor to function incorrectly.
For #1, I just used some super glue to weld the nut into place. This appears to have worked OK, but I fear that the point is weakened now and I will need to be very gentle if I disassemble the phone again.
For #2, The problem was that the housing was allowing bleed through inside the case from the proximity flasher to the light sensor, which caused the sensor to determine that there was something close to it when in fact there wasn't. I placed a small (oh so small) piece of electrical tape into the housing between where the IR flasher and sensor are located, and the problem was resolved.
If presented with the option of purchasing a new digitizer alone, or a new digitizer and housing together, follow groovel76's suggestion; it's well worth the time and money to go with the latter. The hassle of cleaning the old adhesive off of the new housing, and the risks of getting new adhesive in places where you don't want it far outweigh the cost of just getting a housing with adhesive pre-applied. I tried to do just a digitizer first, and ended up with a small amount of super glue (DO NOT RECOMMEND) getting on the new screen and the edge of the housing, as well as a screen that didn't seat properly because I didn't get quite all of the old bits out of the old housing. This resulted in dust getting under the screen and another crack when I attempted to fix what I'd screwed up the first time.
Between the availability of parts and ROMs for this phone, I see it being in my family for a LONG time yet.
Yes! Buy a digitizer online (most come with the tools you need such as the torx screwdrivers, mine did) and search for videos on youtube. That's what I did and it only cost me $37 for the digitizer and about 30 minutes of my time. And it worked perfectly as new when I got it all back together.
I managed to break the screen on my Optimus 3d last night, not sure if it was dropped or ran over. I found it face down in my driveway this morning and to my horror when I flipped it over the screen was completely smashed, however the phone is still working fine, minus the never ending ghost call issue.
What make the situation worse is Rogers just sent me out a replacement phone yesterday and I have to send this one back, in the next couple days.
So I called a repair centre and they wanted $190 to repair the phone, and stated they would need to replace the LCD and the glass screen. I know there is nothing wrong with the LCD screen, phone functions and all colours are good, just has broken glass.
My question is, can I repair just the glass without replacing the LCD? I have found the screen for around $30 on ebay. Based on watching the how to on youtube it doesn't look like too difficult of a job.
n3fta said:
I managed to break the screen on my Optimus 3d last night, not sure if it was dropped or ran over. I found it face down in my driveway this morning and to my horror when I flipped it over the screen was completely smashed, however the phone is still working fine, minus the never ending ghost call issue.
What make the situation worse is Rogers just sent me out a replacement phone yesterday and I have to send this one back, in the next couple days.
So I called a repair centre and they wanted $190 to repair the phone, and stated they would need to replace the LCD and the glass screen. I know there is nothing wrong with the LCD screen, phone functions and all colours are good, just has broken glass.
My question is, can I repair just the glass without replacing the LCD? I have found the screen for around $30 on ebay. Based on watching the how to on youtube it doesn't look like too difficult of a job.
Click to expand...
Click to collapse
First of all , this was asked before. Read the forum. I know because i asked that question.
Check here ;
http://forum.xda-developers.com/showthread.php?t=2021232&highlight=screen
and here ;
http://forum.xda-developers.com/showthread.php?t=1971226
Carefully read them , especially my posts because i did it.
Where are you from and how fast can you get the replacements off ebay ?
When you get them it'll take about half an hour to fix it.
Nobody will notice unless there's damage to the LCD.
If it has we'll have to change it too.
I can guide you via Skype video calling.
Ok so I have managed to remove the broken screen, it was actually fairly easy my only concern is the part show at the 7:00 minute mark of the video below, was broken when I removed it. The copper tape strip (or whatever it is) is still in tact. Where can I purchase this part? I still have all the pieces and if worst comes to worst I will attempt to very carefully assemble the phone with the broken parts to see if the phone still functions. I'm assuming this is part of what operates the home, search, back and menu buttons.
I have already removed the glue and am going to pick up a new screen from London shortly. I had some adhesive remover and work in a glass shop so I have all the tools and cleaners to ensure my new screen sticks and fits nicely.
After reading the thread you linked I am wondering if the screen they sell in London will will include the outside casing, this would solve all of my problems. I guess I will know soon enough, heading to London now. I will let you guys know how I made out.
Heey if you look on youtube you find couple of videos its not very difficult i did it with a friend of my it takes 20 minutes be carful ^^
Goodluck
You can make do without a front case if you know what you're doing. I lacked equipment so i used alternative methods like shoe glue or blowdryer (which killed the original digitizer)...
No matter what you do they'll recognize if you don't buy it with a front casing though... (Already glued preferably)
I found it in turkey so i don't think you can't find it in london , resources are vast there...
Look around.
Remove the digitizer and check the lcd before heading to london if need be buy it as well.
If you need help you know where to find me...
Cheers!
Sent from my LG-P920 using xda app-developers app
Ok so I got the new screen installed and everything is working great. I purchased some 3m adhesive at the repair shop which made for a very clean replacement after removing all the old glue with some adhesive remover. Decided to grab a LCD for my brothers LG970 while I was there and repaired it as well.
New phone arrived yesterday evening, so I will be sending this one back this afternoon. The screen replacement is very clean so I'm not concerned about that but I did manage to lose the little speaker cover from the front of the phone, I just plan on telling Rogers it fell of at some point if they ask about it. Considering the phone is in working order with no physical damage besides wear and tear I don't expect an issue from Rogers.
By the way anyone want to purchase the brand new Optimus3d Rogers sent me? Not even taking this one out of the box, selling it and getting the as far away from LG phones as I can.
Thanks for all the help guys.
I could think about buying it but you need to disassemble it and wrap the parts good.
In Turkey it's illegal to buy phones from foreign countries but it's not if you buy not working parts.
So in short i'm gonna con them into thinking it's for parts if you're up to it. PM me the price in your head.
Sent from my LG-P920 using xda app-developers app
I have sent you a pm. At least I believe I have I don't actually see the message in my sent items list.
Well, I knew the time would come, I shouldn't be so picky on cases. I had my phone in my lap, hopped out of the car and heard my phone drop from my lap. Totally forgot it was there. One corner impact and it cracked my screen, which is disappointing because I drop my iPhone all the time and nothing happens to it. But, at least it's not the whole screen that's shattered, might even be a waste to replace it. The screen is responsive still.
With that said, anyone know where I can get a replacement screen or should I have a "professional" do it?
I'm looking at this:
http://www.ebay.com/itm/LG-Google-N...e_Replacement_Parts_Tools&hash=item233373ec1c
That way there's no damage to the frame.
well yeah i want to know that too and how much it cost me to replace the screen
Sent from my Nexus 5 using Tapatalk
@dinggus
Ebay link looks OK. I guess you can replace screen yourself, if you have "straight" hands. Nexus 5 Teardown should helps you.
BTW, more Parts for Nexus 5.
Well, if you are going to try this one yourself, it's one of the "easier" ones. As long as you get the LCD assembly and frame that is already put together. On eBay, there are some vendors selling the the assembly + frame for $135. No really crazy tools are needed. Shouldn't be anything too catastrophic happen since you are changing the whole front of the phone. If you were trying to separate the top glass, I'd definitely advise against if you aren't a pro. If you absolutely don't feel comfortable with doing it and can be without the phone for a few days, then feel free to PM me, and we can discuss other options.
If you have steady hands, enough patience and some previous experience in disassembling phones (youtube could help a lot), it shouldn't turn out to be quite a big challenge.
I would advise though in some attention taking off the rear cover (it's not difficult, but if you apply too much pressure you might end up bending or breaking it). Same goes with the battery, which is attached to the back of the screen with some adhesive. Use a plastic tool for this, and try to peel it off with a strong and steady hand. Once you do that, it's only a few screws.
I think LG would fix it for $150 so $135 to fix it yourself eh. Unless you want the accomplishment, but I have never ventured into replacing a cracked screen.
Just got off the phone with LG, they said they can't price over the phone, they have to have a tech see the phone and they'll call with a quote. So, 2 weeks without a phone just to get a quote and maybe repaired if I want to spend that kind of money.
I am 80% positive that I have viewed a few post of them charging $150 for screen replacement. You aught to check in the thread "who dropped it" the answer might be there. Its in general. Hard to find with xda app.
Sent from The Deathstar
Well, turns out once the screen is cracked it cracks easier now. As of now, the phone starts clicking on random things when the screen is touched.
I'm debating to either buy a new one and sell this one, should come out to the same price as buying a replacement screen once the cracked phone is sold.
What would you guys suggest? I can't send it in to LG as I need my phone and replacement screen + front housing is $200 to replace myself or $220 to replace by a professional.
I'm looking at this: http://www.etradesupply.com/lg-nexus-5-lcd-screen-and-digitizer-assembly-with-frame.html
It seems to come with majority of everything and I just need to transfer over the antenna wires, motherboard and battery.
or
http://www.repairsuniverse.com/lg-g...exus 5 Screen with Frame&utm_campaign=LE55ONS
I'll have to transfer over everything, which they have a tutorial - https://www.youtube.com/watch?v=OPuCmfhzgbg - which makes me nervous seeing this.
dinggus said:
Well, turns out once the screen is cracked it cracks easier now. As of now, the phone starts clicking on random things when the screen is touched.
I'm debating to either buy a new one and sell this one, should come out to the same price as buying a replacement screen once the cracked phone is sold.
What would you guys suggest? I can't send it in to LG as I need my phone and replacement screen + front housing is $200 to replace myself or $220 to replace by a professional.
Can't you try the below? Quite easy to dis-assemble the phone, steady hands and proper screw driver + torx driver, use a hairdryer to warm up the glue connecting the battery + LCD to the digitizer
Sorry can't post external links to XDA due to post counter search Ebay for "Frame-LCD-Display-Touch-Digitizer-Screen-for-LG-Google-Nexus-5-D820-D821" results are between $108-$120 ...
Click to expand...
Click to collapse