Sim Detected/No Signal "can't connect to this network at the moment try again later"
Hi I had my phone flashed with a custom rom. But later i wanted to switch back to stock. I used the SP tool to flash
Back "sprout_reference_pack_1379542-KPW53_ALPS.KK2.AOSP.SPROUT.SP.p52_karbonn".
But before flashing i accidently used the "Format" tab of SP tool.
After that i flashed my phone to stock.
I have no signal. Sim card is detected.
I tried to switch to lollipop stock still the same error. I switched to other roms too but still no Signal and
"can't connect to this network at the moment try again later" if i do a manual connect.
I noticed that first 2 or 3 times on each rom the manual scan select gave error "Network search error".
The Memory Test Tab of Sp flash tool
Code:
============ Memory Detection Report ===========
Internal RAM:
External RAM:
Type = DRAM
Size = 0x40000000 (1024MB/8192Mb)
NAND Flash:
ERROR: NAND Flash was not detected!
EMMC:
EMMC_PART_BOOT1 Size = 0x0000000000400000(4MB)
EMMC_PART_BOOT2 Size = 0x0000000000400000(4MB)
EMMC_PART_RPMB Size = 0x0000000000400000(4MB)
EMMC_PART_GP1 Size = 0x0000000000000000(0MB)
EMMC_PART_GP2 Size = 0x0000000000000000(0MB)
EMMC_PART_GP3 Size = 0x0000000000000000(0MB)
EMMC_PART_GP4 Size = 0x0000000000000000(0MB)
EMMC_PART_USER Size = 0x00000000e9000000(3728MB)
============ EMMC Test ============
EMMC Pattern Test(0x5A5A):
And its timer continues to go on with red line Download DA 100%
I guess it has to do with NAND.
ERROR: NAND Flash was not detected!
Please tell me how to recover NAND on MT6582
Alast Found the fix for it guys.
It was due to IMEI Error.
Here is the link to fix if you face such issue.
http://forum.xda-developers.com/cro...out4-permanent-fix-invalid-imei-wifi-t3250044
Hello XDA assist,
Mobile - Karbonn A12+ (MT6572)
Issue - mobile not powering up or lighting display at all even while connected to charger no battery charging indication. Only hope I see is when I connected without battery to computer device drivers detected which is usual for hard flashing.
Notes - Mobile had not fallen and in working condition on my desk , last time I see it on 16% battery suddenly it became off & never light up later.
Current installed ROM is complete fresh and very few apps. Earlier to day I m trying to fix or disable proximity sensor detection with few rooted apps like xposed modules etc but none worked. Later thus also I did lot of internet browsing as well before BLANK OFF.
Trials & Findings.
Long press power button for 1 min.
Shorting +- terminals of power button.
Power + volume up for boot mode.
Connected with out battery to computer for adb boot even Without power+volup its being detected after every 3 secs in windows devices as below but not lighted its display any time....
In Device Manager, it detected as follows...
>Mobistel Cynus F4 PreLoader USB VCOM Port
=== New Trials & Updates ====
I could find that it must be a HardBrick, as not lighting up but still detected in windows.
I did scatter_loading using Sp flash tool & i got download OK message.
But still i am unable to boot it or light up my screen nor battery charging.
Ran a memory test using Sp_Flash tool, below is the result.
============ Memory Detection Report ===========
Internal RAM:
Size = 0x00020000 (128KB)
External RAM:
Type = DRAM
Size = 0x20000000 (512MB/4096Mb)
NAND Flash:
ERROR: NAND Flash was not detected!
EMMC:
EMMC_PART_BOOT1 Size = 0x0000000000200000(2MB)
EMMC_PART_BOOT2 Size = 0x0000000000200000(2MB)
EMMC_PART_RPMB Size = 0x0000000000200000(2MB)
EMMC_PART_GP1 Size = 0x0000000000000000(0MB)
EMMC_PART_GP2 Size = 0x0000000000000000(0MB)
EMMC_PART_GP3 Size = 0x0000000000000000(0MB)
EMMC_PART_GP4 Size = 0x0000000000000000(0MB)
EMMC_PART_USER Size = 0x00000000e7000000(3696MB)
UFS:
ERROR: UFS was not detected!
============ RAM Test ============
Data Bus Test:
[D0][D1][D2][D3][D4][D5][D6][D7][D8][D9][D10][D11][D12][D13][D14][D15][D16][D17][D18][D19][D20][D21][D22][D23][D24][D25][D26][D27][D28][D29][D30][D31]
OK!!
Address Bus Test:
[A1][A2][A3][A4][A5][A6][A7][A8][A9][A10][A11][A12][A13][A14][A15][A16][A17][A18][A19][A20][A21][A22][A23][A24][A25][A26][A27][A28]
OK!!
RAM Pattern Test :
Writing ...
0x44332211,
0xA5A5A5A5,
0xA5A5A500,
0xA500A500,
0xA5000000,
0x00000000,
0xFFFF0000,
0xFFFFFFFF,
OK!!
Increment/Decrement Test:
Writing...
OK!!
============ EMMC Test ============
EMMC Pattern Test(0x5A5A):
(0x00600800),(0x00601000),(0x00601800),(0x00602000),(0x00602800),(0x00603000),(0x00603800),(0x00604000),(0x00604800),(0x00605000),(0x00605800),(0x00606000),(0x0066800),(0x00607000),(0x00607800),(0x00608000),(0x00608800),(0x00609000),(0x00609800),(0x0060A000),(0x0060A800),(0x0060B000),(0x0060B800),(0x0060C000),(0x0060C800),(x0060D000),(0x0060D800),(0x0060E000),(0x0060E800),(0x0060F000),(0x0060F800),(0x00610000),(0x00610800),(0x00611000),(0x00611800),(0x00612000),(0x00612800),(0x0061300),(0x00613800),(0x00614000),(0x00614800),(0x00615000),(0x00615800),(0x00616000),(0x00616800),(0x00617000),(0x00617800),(0x00618000),(0x00618800),.............................
Continues...........Continues ...........Continues ...........Continues ...........Continues ...........Continues ...........Continues ...........Continues ...........Continues ...........
................................(0xC432C000),(0xC432C800),(0xC432D000),(0xC432D800),(0xC432E000),(0xC432E800),(0xC432F000),(0xC432F800),(0xC4330000),(0xC4330800),(0xC4331000),(0xC4331800),(0xC4332000),(0xC4332800),(0xC4333000),(0xC4333800),(0xC4334000),(0xC4334800),(0xC4335000),(0xC4335800),(0xC4336000),(0xC4336800),(0xC4337000),(0xC4337800),(0xC4338000),(0xC4338800),(0xC4339000),(0xC4339800),(0xC433A000),(0xC433A800),(0xC433B000),(0xC433B800),(0xC433C000),
FAILED!!
============ Memory Detection Report ===========
##########################
Please light up my device...
Thanks in advance...
Happy to hear any kind of opinions...
##########################
@xdaAssist ,
eagerly waiting for a solution for this.
Before I do brick or break my phone by doing something else wrong.
Please light up my mobile.
Assist team,
Please help me light up my device...
Or do suggest me where i can post this thread.
Hello xda , am I in wrong section. some one please spare 5 mins for me & throw some idea please.
Sent from my CP8298_I00 using Coolpad Forums
Hello,
Once posted please wait for 24 hours before bumping the thread.
Also you may post your query here Android Q&A Forum with all relevant details, the experts there maybe able to assist you.
Regards
Vatsal,
Forum Moderator.
Hello
I have this Huawei G610, suddenly it show me that Encrypted unsuccessful message, then I tried to reset the phone and it doesn't want to.
I tried to Hard reset and i can't go to the Hard reset part>
When I connect it to the usb port in order to try to flash it using stock rom and SP flash tools, the program can't complete formatting with an error. and my phone keeps showing the logo and vibrate then close and open doing the same thing again and looping.
I tried to make a memory test, and that was the results:
=============== Memory Detection Report ===============
Internal RAM:
Size = 0x00020000 (128KB)
External RAM:
Type = DRAM
Size = 0x40000000 (1024MB/8192Mb)
NAND Flash:
ERROR: NAND Flash was not detected!
EMMC :
EMMC_PART_BOOT1 Size = 0x0000000000200000(2MB)
EMMC_PART_BOOT2 Size = 0x0000000000200000(2MB)
EMMC_PART_RPMB Size = 0x0000000000200000(2MB)
EMMC_PART_GP1 Size = 0x0000000000000000(0MB)
EMMC_PART_GP2 Size = 0x0000000000000000(0MB)
EMMC_PART_GP3 Size = 0x0000000000000000(0MB)
EMMC_PART_GP4 Size = 0x0000000000000000(0MB)
EMMC_PART_USER Size = 0x00000000E7000000(3696MB)
============ RAM Test ============
Data Bus Test :
[D0][D1][D2][D3][D4][D5][D6][D7][D8][D9][D10][D11][D12][D13][D14][D15]
OK!!
Address Bus Test :
[A1][A2][A3][A4][A5][A6][A7][A8][A9][A10][A11][A12][A13][A14][A15][A16][A17][A18][A19][A20][A21][A22][A23][A24][A25][A26][A27][A28][A29]
OK!!
RAM Pattern Test :
Writing ...
0x44332211,
0xA5A5A5A5,
0xA5A5A500,
0xA500A500,
0xA5000000,
0x00000000,
0xFFFF0000,
0xFFFFFFFF,
OK!!
Increment/Decrement Test :
Writing ...
OK!!
============ NAND Test ============
SKIP! NAND Flash was not detected!
============ EMMC Test ============
EMMC Pattern Test(0x5A5A):
FAILED!!
============================================================================================
is it an EMMC problem? Needed to be replaced or what ??
Help Needed ... Thanks in advance
?
any one ??
PLZ
Hello
I've bricked Oppo F1s when I've tried to flash it
this is infinity read info log
Wait for phone...
Phone found! [ 1087 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6755
BB_CPU_NME : [MediaTek] Helio[P10]|MT6755_S00
BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x01000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : SIGNED with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
DAgent configured successfully
Connection agent : BROM
[DA_ERROR] : DRAM Configure failed!
ErroCode : 0x2122and I get this message error if I try to flash it with MT6750
Error: STATUS_INSUFFICIENT_BUFFER
EMICFG_NOT_ACCEPTED_CONFIG
Boot Error!
Operation Failed
Elapsed: 00:00:52
Reconnect Power/Cable!
Click to expand...
Click to collapse
it says that's an MT6755 processor , but when I try to flash it with Mt6755 with sp flashtool and NCK mtk soft it says that's version mismatch and it's and MT6750 device
Can you help to choose the right firmware please ?
octopus82 said:
Hello
I've bricked Oppo F1s when I've tried to flash it
this is infinity read info log
it says that's an MT6755 processor , but when I try to flash it with Mt6755 with sp flashtool and NCK mtk soft it says that's version mismatch and it's and MT6750 device
Can you help to choose the right firmware please ?
Click to expand...
Click to collapse
I have pretty much the same problem with my MOTO M (XT1662). It happened after I did the "Format whole flash" in SP flash tool.
Now the SP flash tool is giving me the following,
Chip Info
=======
Chip name: MT6755
Chip Version: 0x0000cb00
Ext Clock: EXT_26M
Extern RAM Type: DRAM
Extern RAM Size: 0xc0000000 (!!!)
SRAM Size: 0x00040000
EMMC Flash
=========
Boot 1 Size: 0x400000
Boot 2 Size: 0x400000
RPMB Size: 0x400000
GP1 Size: 0x0 (same for GP2, GP3 and GP4)
UA Size: 0x747c00000
No matter what ROM I'm trying to flash (stock or custom) , I always get the error "STATUS_INSUFFICIENT_BUFFER (0xC0010007)".
It looks like it has to do something with the External RAM Size (0xc0000000).
I found this firmware "XT1662_Kungfu_m_MT6755_USR_S0924_1612291517_mp7V2.3_CN (RepairMyMobile.in)", which seems to be what I need but I can't get pass this error.
Any help will be greatly appreciated.
i have the same problem
STATUS_INSUFFICIENT_BUFFER (0xC0010007)
i try to update with OTA and failed too
anyone can help ?
Hello i have A8 2018 sm-a530f which has the emmc files corrupted , i need to revive and when i connect to the Easy Jtag Plus i get the error Partition info not found ,guide repair procedures and below is the log data
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 445 mV
CMD Active Level: 1192 mV
EMMC Device Information :
EMMC CID: 150100424A5444345200523F424BB5A7
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A544434xx , S/N: 523F42xx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 11/2018
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_523F424B_20210404_201644.extcsd
EMMC Init completed.
Scanning soft partitions
Partition table not found
Get firmware version
Firmware info not found
NOTE: I HAVE THE BACK UP FILE BUT I DO NOT KNOW WHICH FILES TO LOAD , MAY SOMEONE CHECK THE ATTACHMENT AND TELL ME WHICH FILES TO LOAD LIKE (Select eMMC Image file *.bin) from THIS BACK UP.MAY SOMEONE TELL ME FROM THE BACK UP WHICH ONE IS ( eMMC ROM1 Image file, eMMC ROM2 Image file, eMMC ROM3 Image file, eMMC GP1 Image file, eMMC ExtCSD file. IN THEIR ORDER.
gruka said:
Hello i have A8 2018 sm-a530f which has the emmc files corrupted , i need to revive and when i connect to the Easy Jtag Plus i get the error Partition info not found ,guide repair procedures and below is the log data
Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 445 mV
CMD Active Level: 1192 mV
EMMC Device Information :
EMMC CID: 150100424A5444345200523F424BB5A7
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: BJTD4R , HEX: 424A544434xx , S/N: 523F42xx , rev. 0x00
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 11/2018
EMMC ROM 1 (Main User Data) Capacity: 29820 MB (000747C00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x01 , width 4bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: BJTD4R_523F424B_20210404_201644.extcsd
EMMC Init completed.
Scanning soft partitions
Partition table not found
Get firmware version
Firmware info not found
NOTE: I HAVE THE BACK UP FILE BUT I DO NOT KNOW WHICH FILES TO LOAD , MAY SOMEONE CHECK THE ATTACHMENT AND TELL ME WHICH FILES TO LOAD LIKE (Select eMMC Image file *.bin) from THIS BACK UP.MAY SOMEONE TELL ME FROM THE BACK UP WHICH ONE IS ( eMMC ROM1 Image file, eMMC ROM2 Image file, eMMC ROM3 Image file, eMMC GP1 Image file, eMMC ExtCSD file. IN THEIR ORDER.
Click to expand...
Click to collapse
I think there are not many users who are able to help in your case.
I only found this thread about emmc repair for your device:
Samsung A520f ,A530f Dead boot repair direct emmc file download
gsm flash,gsm flash file,gsm crack,combine file,easy firmware,frp file,gsm firmware,gsm file,samsung firmware,samsung dump,all android flashing tool,
www.awaismobile.com
Yes i downloaded the file ,how do i know this file is rom 1 ,Rom2,Rom 3, and ex PLEASE I DENTIFY FOR ME