stock, non-rooted Android 5.0
Phone is soft bricked, turns on and freezes on the yellow Sprint splash screen.
I need to recover some files on internal storage.
I know that I could install ADB and use the adb pull command to transfer files to a PC, but I am under the impression that USB debugging needed to be turned on, it is not.
Other options? Thank you.
Actually, it turns out that usb debugging was enabled.
while stuck in the bootloop at the sprint screen I use adb.exe with command prompt:
adb devices
device is recognized
adb pull /sdcard c:/recovered_files
"device unauthorized"
have to figure out how to get around the authorization
Also tried to flash a custom recovery (Philz and TWRP) Odin says it was successful every time, then it boots into and sticks at the Sprint screen. I reboot (remove battery) and it's still the stock recovery
Edit: fixed it. Learned that "install-recovery.sh" resets the recovery at each OS boot, so just needed to turn off "auto-reboot" in Odin. Once I had Philz recovery installed, used adb to pull all the files I needed.
Related
Okay, first of all I know, I'm a total noob. I have followed these forums a long time and have successfully rooted a few phones. One of which was my nexus s 4g. I was trying to unroot the phone so I could get ics. This is when I ran into problems and right now I just want to be able to get my phone working again. Right now I am stuck on the Miui boot up screen and no matter how long I wait it stays on that screen. If I do a battery pull and hold down power and vol up I can get into the bootloader screen with the information as follows: fastboot mode, product name-Herring, HW Version Rev 34, Bootloader version-D720SPAKE1, Baseband version-D720SPAKE1, Carrier info, SPR, serial number-37308B81276A00EC, Lock State-locked. Then the different options I can choose are reboot bootloader, reboot, recovery, power off. If I choose reboot, it takes me back to the mius screen and stays there. If I choose recovery, I get the triangle with the exclamation point. I then hold power and up volume again and I get a screen that says Android system recovery <3e> with reboot system now, apply update from sd card wipe data/factory reset and wipe cache partition. I have tried all of these as well with no luck. When I go to apply update from sd card I get matrix-cfs_v15.5 zip, root.zip, update.zip and then what looks like apps such as Alarms/, Android/,MIUI?, etc. If I try to select any of the first ones such as matrix-cfs_v15.5 zip, I get Install /sdcard... , finding update package..., opening update package..., verifying update package..., E.signature verification failed, Installation aborted. Then it gives me the system recovery options again. Any help would be appreciated.
Did you try ADB fastboot method?
Not sure how to try that
I tried doing the adb, followed all directions and installed and when I go to the command prompt and type in anything, such as, adb reboot bootloader I get, adb is not recognized as an internal or external command, operable program or batch file.
ok I got that working now but when I type adb devices and press enter I get a message saying List of devices attached and then it doesn't show anything and I get the command prompt again saying:c:\android\android-sdk\platform-tools>
also since the phone is stuck in either the miui screen or bootloader I can't get into it to put it in usb debugging mode. I am trying on my own to get this going and am stuck any and all help would be very much appreciated.
TerryUK98 said:
Lock State-locked.
Click to expand...
Click to collapse
I think that means you have a locked bootloader.
And from what you're telling, I believe you have stock recovery.
Also, when you're in fastboot mode, I don't think adb commands apply. Use fastboot commands instead (i.e. fastboot devices).
Search for guides showing you how to install and use fastboot.
I did fastboot as well and the problem I think I am having is it's not recognizing my phone because usb debugging wasn't turned on before it locked up. How would I get it to recognize my phone or download an img to my phone if it is not being recognized. Sorry if this is a stupid question.
You don't need usb debugging in fastboot mode.
You either:
1. Don't have drivers installed.
2. Don't have fastboot installed correctly.
You really need to read a guide or two, through and thoroughly.
Bc it sounds like you have no clues.
Yeah dude. Take a step back and go over what you have installed and where you installed it.Yes, fastboot commands start with fastboot instead of adb. And you're on stock recovery.
Thanks for the answer that I don't need usb debugging in fastboot mode, I wasn't sure of that. I have downloaded and installed my drivers multiple times and when I use the device manager to update drivers it says I have the latest drivers installed already. Whenever I do fastboot commands I will type in fastboot devices and shouldn't my device serial number come up? It just gives me the line c:\android\android-sdk\platform-tools>
And is waiting on me to type a command in. And yes I have been looking at guides all night. I appreciate any help you guys might have and remember we were all noobs at one time.
The zip in this tutorial should help.
It has adb, fastboot, and the drivers needed.
And unlock the bootloader because it is locked.
Finally got it, I had everything downloaded that I needed already, but looking at different forums, etc, it seemed like everyone named it something different. So I just used the one link you gave me and did it exactly the same way and it worked. Thanks so much! and again thanks for your patience.
I'm kind of screwed and It's not even my mistake, I guess.
I clean flashed the Mahdi Update 25/04 yesterday earlier I had 03/03. In the morning I experienced 2 -3 random reboots and later only one random reboot after which my phone won't boot (bootloop). When i enter bootloader, it automatically selects "start" and boots into system and then reboots.
Once i got the chance and my phone booted fully. But then when I selected reboot into recovery so that i can restore a NAND. IT reboots, the team win logo shows up and then the cycle repeats.
Basically, i don't have access to recovery, my bootloader isn't stable (i.e. it automatically boots without selecting) so I'm unable to flash a stock img as of now. If and when my Nexus fully boots into system it stays the same for about 1 hr if i have any luck. PLz help.
From India. Unlocked Bootloader and custom Rom "Mahdi".
Have you tried using add to boot into recovery? If not also try to getting a logcat when it reboots, those will give us a little more of a general idea of what is actually happening.
First thing don't panic. You can't brick a nexus. You should be able to get into bootloader (volume down + power button) use Wugs Nexus Root toolkit from XDA forum. reload stock ROM in fastboot mode. I have done this lots of time. It's a draw back to being a tinkerer just can't leave well enough alone.
It sounds like your power bottom might be stuck to be honest.
Sent from my Nexus 5 using Tapatalk
nyterage said:
Have you tried using add to boot into recovery? If not also try to getting a logcat when it reboots, those will give us a little more of a general idea of what is actually happening.
Click to expand...
Click to collapse
I managed to somehow get into my bootloader and flashed the following
1. bootloader.img
2. radio.img
3. system.img
4. stock kernel (boot.img)
5. twrp recovery.img
I skipped userdata,img as i need to save my data.
I then went into recovery and did a factory wipe (not including internal storage)
My stock rom booted BUT the setup screen showed up and during the setup process it rebooted again and I couldn't mount my storage to backup.
MY MAIN PRIORITY IS TO COPY THE CONTENTS OF MY SD CARD Before flashing the whole stock image (including userdata)
Now when I type "adb version" in cmd I get Android Debug Bridge Version 1.0.31 but when I type "adb devices" whilst my phone is in fastboot mode, it doesn't list my phone. So i'm unable to "adb pull /mnt/sdcard"
I'm in the same situation with rare access to B/L (based on luck) and Recovery.
Plz tell me what to do when I am able to connect in bootloader mode (fastboot)
IF required I can upload a video showing that what problem I am facing.
scuccria said:
I managed to somehow get into my bootloader and flashed the following
1. bootloader.img
2. radio.img
3. system.img
4. stock kernel (boot.img)
5. twrp recovery.img
I skipped userdata,img as i need to save my data.
I then went into recovery and did a factory wipe (not including internal storage)
My stock rom booted BUT the setup screen showed up and during the setup process it rebooted again and I couldn't mount my storage to backup.
MY MAIN PRIORITY IS TO COPY THE CONTENTS OF MY SD CARD Before flashing the whole stock image (including userdata)
Now when I type "adb version" in cmd I get Android Debug Bridge Version 1.0.31 but when I type "adb devices" whilst my phone is in fastboot mode, it doesn't list my phone. So i'm unable to "adb pull /mnt/sdcard"
I'm in the same situation with rare access to B/L (based on luck) and Recovery.
Plz tell me what to do when I am able to connect in bootloader mode (fastboot)
IF required I can upload a video showing that what problem I am facing.
Click to expand...
Click to collapse
To use adb pull you have to enter the recovery. You need universal naked usb driver 0.73 to make adb work in recovery. If you are on windows 8 or 8.1 you have to turn off the driver signiture enforcement befote installing the universal naked usb driver 0.73
Tapatalk-kal küldve az én Nexus 5-el
El Daddy said:
It sounds like your power bottom might be stuck to be honest.
Click to expand...
Click to collapse
I agree. It's a malfunctioning power button due to several reasons (moisture, drops, etc.). I had this on my Nexus S.
I have a stock N5 that has a broken screen. You can see some parts of it but doesn't respond to touch at all. I saw there was an app on here that let's you see and remotely control the screen using your PC with adb. It looks like I might have the usb debugging turn on, however my adb shell is not authorized but does see the device. I have tried booting into stock recovery, but adb is not running at that time to allow me to push access keys.
What options do I have to be able to remotely use this phone. I want to use it as a camera for tinycam pro
Sent from my Pixel using Tapatalk
If your bootloader is unlocked, you can boot TWRP without flashing anything. From TWRP you'll get adb access.
If your bootloader is locked, you're doomed. :-/
Bootloader is locked. Is there anything I can flash to get it to work.
Sent from my Pixel using Tapatalk
I was able to use fastboot and unlock the bootloader. The phone restarted and went to a welcome screen. I was then able to flash twrp in recovery and load that up. I got into adb shell and ran some echo commands to put things into the default.props file in an attempt to enable us debugging when it rebooted. Well I guess the commands we're not correct or something but it didn't work. So then I went back into the bootloader and I thought I had to reflash twrp again, so I ran the same fastboot command I did before to load twrp. Says it wrote fine but now when I select recovery the phone just reboots back to the welcome screen. Since most of the screen is messed up o can't make out why that happens. Any help would be appreciated
Sent from my Pixel using Tapatalk
In case anyone else has the similar problem, once back into TWRP by using 'fastboot boot <img>', i used this post to mount the file system under system2 folder - https://forum.xda-developers.com/showpost.php?p=63829295&postcount=27
I then pushed my adb key onto the device so when the OS boots back up, it would allow adb to connect
Code:
adb push C:\Users\<username>\.android\adbkey.pub /data/misc/adb/adb_keys
Hey guys, in a little bit of a dilemma.
My s6, for some reason, cannot pass the flashing "Samsung" logo when booting it up. I have not rooted this phone, nor have I installed a custom recovery or rom. This phone is stock as it gets.
And I need to recover the photos off the phone. Issue is, I thought it would be simple as going into recovery mode and doing adb pull/sdcard/DCIM/Camera or something like that.
BUT I do not have USB debugging enabled!!! Never even turned on developer settings.
I tried to get into bootloader and use fastboot, but fastboot devices shows up with nothing. adb commands do not work, except when I press "install update from ADB", then only the very basic ADB commands work such as adb reboot, adb sideload etc.
So I am not sure what to do from here. Fastboot is not working (I have installed the Samsung drivers from the official webpage, but I haven't restarted my computer so i will try that).
Please help me to recover these photos :crying::crying::crying:
Hi,
If Download mode is working, flash TWRP recovery with Odin.
Go to Mount, select Data partition > Enable MTP and access files from PC.
Recover your data, then flash fresh new ROM https://forum.xda-developers.com/galaxy-s6/general/guide-tutorial-howto-samsung-galaxy-s6-t4108425
I just tried rooting my phone. The phone is cycling back and forth between the bootloader is unlocked screen and the Motorola splash screen.
To repeat some steps from a prior post.
My phone had QPR30.80-58-3 .
I downloaded that ROM and extracted the boot.img file.
I downloaded the latest Magisk Manager and installed it on my phone.
I ran through the patching process for boot.img.
I requested an unlock code from Motorola and unlocked the bootloader.
I flashed the patched boot image which patched partition b.
I flashed the patched boot image to partition a.
I rebooted which began the cycle.
I tried holding down the power button but it returns to the cycle.
I can get back to the bootloader with the Volume Down and Power buttons.
Any suggestions on what could get me back to a functioning phone, rooted or not rooted?
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
dafunk60 said:
I would confirm the version of the boot image you flashed matches the version of the installed rom. You could also try to flash the unpatched / original boot.img to see if that gets you booting again.
Click to expand...
Click to collapse
I checked that the image I patched was from the QPR30.80-58-3 ROM which matched the level after the phone was updated.
I flashed that original boot image which flashed partition a and then rebooted. I did not flash partition b.
It first came up with the unlock warning screen. It sat on the Motorola splash screen for a noticeable amount of time followed by a yellow screen with a circle around the Motorola symbol. Finally it ended up on a blue Hello there screen with a yellow start button.
This screen was unresponsive. Eventually through various cyclings through all this I ended up on a screen that said Android could not boot and gave me an option of a factory reset. I did that but it did not help getting past the Hi there screen.
I went back and flashed the QPR30.80_58 image on both partitions a and b. This got me back to setting up the phone again. The phone is at QPR30.80_58. I am considering just rooting at this level.
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
DougPeterson said:
So I tried patching the original QPR30.80_58 boot image. I did notice that it appeared the phone had automatically staged the QPRS30.80_58_3 update. I proceeded in (false) hopes that I could stop that.
It flashed the b partition. Ended up stuck in the bootloader unlock loop. I flashed the a partition but no change.
Previously I had ended up on a recovery screen automatically after some time. I could not force this to happen.
I tried flashing the original unpatched boot image but would end up on a non-functioning Hello there screen.
I tried adb recovery and adb shell but came back with device unauthorized.
I tried following some instructions on using fastboot erase userdata and fastboot erase cache. No change.
I finally found out that the Recovery menu was option off the bootloader screen. However, that came up with No command.
Lenovo Rescue did not want to recognize my XT2043-4 device.
I flashed the unpatched retail QPRS30.80_58_3 boot image to both a and b partitions. That got me back to a functioning phone. After getting through the login and setup steps I did find that it was at QPRS30.80_58_3.
Out of curiosity, I tried Lenovo Rescue again. I received a "Failed to match connected device. Reconnect device, then try again." which did not work.
Now I am at a loss.
Click to expand...
Click to collapse
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
dafunk60 said:
Happy to hear you have a working phone again! The lack of touchscreen response & the stuck at the hello screen issues are what others have reported when they used a boot image from a different version than on the phone. I suspect that something got confused between the version & slot somewhere along the way. As far as the Lenovo Rescue software not seeing the phone, it's communicating via ADB. If I recall correctly I needed to reauthorize the PC to connect via ADB after updating from 30.80-58 to 30.80-58-3. When I connect the phone via USB there's a popup on the phone asking to authorize the PC. Can you connect via ADB in the command line? If yes, you may want to reinstall the Lenovo software. If no, I would troubleshoot the ADB connection.
I originally rooted the 30.80-58 version. When 30.80-58-3 was released all I did was flash the unpatched boot.img, took the update OTA, let it reboot, then flash a patched boot.img from 30.80-58-3. All worked as expected, user data was intact.
Click to expand...
Click to collapse
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If you want to get into recovery, boot into the bootloader than do
Code:
fastboot reboot fastboot
That'll boot you into fastbootd which has an option to go to the real recovery
DougPeterson said:
I double checked that I had USB debugging set, given I have reset a couple of times. I revoked all USB access and reinstalled the Rescue app. I still get the Failed to match connected devices error.
fastboot device will list the phone.
adb devices or adb devices -l does not list anything and adb shell says no devices/emulators found.
If I try to get into recovery mode I get a No command screen. I have been trying to take notes on what I did but there have been gaps in all the fiddling. I may have only flashed one partition the last time I tried putting back a stock boot image.
For USB drivers I downloaded the latest from Motorola. Was that sufficient for this?
Click to expand...
Click to collapse
If adb isn't showing any devices connected that would explain why the rescue software cannot find your phone. Perhaps you don't have the correct driver installed. Windows Device Manager shows the phone as a Motorola ADB Device on my PC.
View attachment 5061327
Another possibility is that you have multiple versions of adb on your PC. Older versions won't work but the adb.exe in "C:\Program Files (x86)\Rescue and Smart Assistant" works for sure. With your phone booted into android & unlocked, plug it into your PC. Do you see the "USB debugging connected" on the phone? If you don't I would re-check that USB debugging is enabled. If you do see the debugging notification, on your PC, open a command prompt and navigate to "C:\Program Files (x86)\Rescue and Smart Assistant". Run
Code:
adb devices
Does adb find your phone?