Database Info

Nexus One to CyanogenMod How Do You Do It

So i read a story on Engadget that would allow the Nexus One to record videos in 720p. I wanted to do that but i was told that i had to modify my phone with some program called cyanogenmod. I was linked to this guide:
edit: well i'm not allowed to post links on this forum, that sucks. I'll just post a snippit of the webpage.
Prerequisites
In order to flash a fully stock Nexus One with any ROM, you must first unlock the bootloader of your Nexus One and flash a Recovery Image. If your Nexus One's bootloader is already unlocked, and you already have a Recovery Image installed, skip this section.
WARNING: UNLOCKING THE NEXUS ONE'S BOOTLOADER WILL VOID YOUR WARRANTY!
You will need the fastboot shell on your computer to use the commands to unlock the bootloader. Follow the Install the Latest Android sdk guide, to get the ADB and Fastboot shell on your computer.
Before continuing, you should first copy all the necessary files to your SD Card. Doing so will make the entire process much easier and faster. Please do the following to copy the files from your computer to SD card root if your Mass storage is not mounted or you get error when trying to access the mass storage drive.
Connect Nexus One to Computer
Make sure the computer picks up the newly connected device and shows a new mass storage drive
On the phone, pull down the top notification slider, you should see an item called "USB Connected"
Click on the "USB Connected" and click Mount. This will make the phone SD Card available for use with computer
Copy the required files
Files you will need:
Download the latest release of CyanogenMod for the Nexus One and the Google Addon from here Mirror1 Mirror2 Mirror3 Mirror4 Mirror5 Mirror6 Copy these two to your SD Card
Download the latest release of Amon_Ra's Nexus One Recovery Image from - Leave the recovery.img on your pc
Rename Amon_Ra's recovery file "Recovery.img", and make sure you have copied the above two zip files to the root of your SD Card.
Power off your phone.
Boot into Bootloader Mode.
Hold down the trackball, and press the power button. Do not let go of the trackball until the phone boots into bootloader mode (You will see a white screen with three skating bugdroids).
Unlock the Bootloader.
Make sure your phone is connected to your PC.
On your PC, navigate to the AndroidSDK\tools folder.
Hold down the Shift key, Right click on an empty space inside the folder, and press "Open command window here". (note: on Windows XP, this might not work. Instead, you may need to open the command window by going to Start - Run - Type "cmd" - press Enter, then type "cd c:\AndroidSDK\tools" (without the quotes), press Enter)
Inside the command prompt that opens up, type in the following command:
fastboot oem unlock
On your phone, a prompt will open up, asking you if you are sure you want to unlock your bootloader, and again warning you that doing so will void your warranty. If you agree to these terms, press Volume Up to select Yes, and then press the Power button to confirm.
Your phone will restart. Let the phone boot into Android. Switch the phone back to usb debugging (unlocking bootloader causes a wipe, reseting settings), and then Power Off the phone.
Once again, boot into bootloader mode.
Flash Recovery.
Note: The Recovery.img should NOT be on the SD Card, it should be in the current working directory.
On the command prompt you opened earlier, type in the following command:
fastboot flash recovery Recovery.img
The recovery image should now be installed on your Nexus One.
Click to expand...
Click to collapse
But i'm lost. I downloaded all the necessary files so far but i'm confused up to this point:
Boot into Bootloader Mode.
Hold down the trackball, and press the power button. Do not let go of the trackball until the phone boots into bootloader mode (You will see a white screen with three skating bugdroids).
Unlock the Bootloader.
Make sure your phone is connected to your PC.
On your PC, navigate to the AndroidSDK\tools folder.
Hold down the Shift key, Right click on an empty space inside the folder, and press "Open command window here". (note: on Windows XP, this might not work. Instead, you may need to open the command window by going to Start - Run - Type "cmd" - press Enter, then type "cd c:\AndroidSDK\tools" (without the quotes), press Enter)
Inside the command prompt that opens up, type in the following command:
Click to expand...
Click to collapse
I'm on a Mac so i dunno if that makes a difference to how i approach this. but when i power my phone down and boot it into bootloader mode, i can't access the phone on the computer because the phone isn't mounted, its at the white screen. how can i access this androidSDK/tools folder?

Flashing stock recovery for those who Stuck at boot screen ninja A87

Download recovery - recovery.img
1. Make sure you have ADB or the SDK installed.
If you have rooted your phone successfully then you must have it installed.
2. Download the files from this link : platform-tools.rar
3. Extract the downloaded file to a location of your choice
for example - D:\SDK
4. Now go the folder, press the shift button and right click. You would see an option 'Open command prompt here' - click that to open command prompt.
5. Connect your phone switched off to the pc and press the volume down button and the power button for 10 seconds. You should see the micromax logo.
6. In command prompt type "fastboot devices" without quotes and hit enter.
7. you should see something like
List of devices attached
M7------ device
8. Now copy the recovery.img to the same folder you had extracted the files earlier.
9. In the command prompt window, type "fastboot flash recovery recovery.img" without quotes and hit enter
10. After you get a confirmation that flash is successful.
11. Remove the phone and boot into recovery.
Very Simple N Easy way

[Q] weird problem on Nexus S - please assist

This is going to be pretty long and have had the problem for months so please bear with me, read and see if you could assist.
Borrowed a friends Nexus S a while back. Used it for a few days, turned it on one day and it stays on the black google screen with the open padlock at the bottom
I am able to enter Fastboot mode is shown in image 2; lock state is unlocked.
I followed the instructions as in post 2 on the following thread
HTML:
http://forum.xda-developers.com/showthread.php?t=1787169
and as copied below but when i got to the part where i needed to mount my sdcard i get the error " unable to write to ums lunfile (no such file)".
Originally Posted by SamuelDebruyn View Post
Ok, you'll need a Windows computer to fix this. Linux should work too but if you're using Linux I guess you could figure out what would be the instructions for Linux yourself. Mac would work too but I don't know how.
Download and install the Android SDK on your computer from http://developer.android.com/sdk/index.html
Open the SDK Manager (there should be a shortcut in your start menu) and install "Android SDK Tools" and "Android SDK Platform-tools" and "Google USB Driver" (it's in Extra).
Turn your phone off, take the battery out, look at the bottom of the phone and write down the model number.
Now go to https://developers.google.com/android/nexus/images and download the factory image for your model for version 4.0.4.
You'll need something like 7-Zip (http://www.7-zip.org/) to open it.
Copy image-so....zip, radio-crespo...img and bootloader-crespo...img from the factory image to the platform-tools directory (on most computers it will be C:\Program Files (x86)\Android\android-sdk\platform-tools and you'll need Administrator rights).
Now open the platform-tools directory from the Android SDK and right click on an empty space while holding the SHIFT button and select "Open command prompt here".
Put the battery back in your phone and press Power while holding the Volume-Up button so it will boot into fastboot mode. Then connect it to your pc.
If Windows starts complaining about drivers then point it your SDK installation directory (include subfolders) or use 7-Zip to unpack http://www.mediafire.com/?5a7gou9droidi53 and point Windows to the directory where you unpacked it. More info on http://www.sevenforums.com/tutorials...e-manager.html
When you type "fastboot devices" and press Enter in the command prompt you opened before it should list one device (being your phone).
If you haven't unlocked your phone before type "fastboot oem unlock" and press Enter. Follow the instructions on the screen on your phone to complete the unlock.
Next type "fastboot flash bootloader bootloader-crespo...img" (you can press TAB to auto-complete) and press Enter. (THIS IS THE MOST IMPORTANT STEP, IF THIS GOES WRONG YOUR PHONE IS SCREWED. Don't continue if another step didn't succeed. If this works, then you can do anything with it.)
Now type "fastboot reboot-bootloader" and press Enter and wait for your phone to reboot into fastboot mode.
Next type "fastboot flash radio radio-crespo...img" (you can press TAB to auto-complete) and press Enter.
Now type "fastboot reboot-bootloader" and press Enter and wait for your phone to reboot into fastboot mode.
Next type "fastboot -w update image-....zip" and press Enter.
Now type "fastboot reboot-bootloader" and press Enter and wait for your phone to reboot into fastboot mode.
Next download http://download2.clockworkmod.com/re...0.7-crespo.img and also put it in the platform-tools directory.
Then type "fastboot flash recovery recovery-clockwork-6.0.0.7-crespo.img" and press Enter.
Now type "fastboot reboot-bootloader" and press Enter and wait for your phone to reboot into fastboot mode.
Now use the volume keys on your phone to navigate to the word Recovery and press the Power button to boot into recovery.
You're now in CWM Recovery, use the volume keys and the power button to go to Mounts & Storage > Mount USB Storage (you might have to scroll down). Now it will come up on your pc and you can transfer the update file for Jelly Bean to your phone. You can find it here: http://forum.xda-developers.com/show...68&postcount=1 (use the one for your model for IMM76D).
Unmount the usb storage, go back to the main menu and go to Install Zip from sdcard > Choose zip from sdcard and open the update file you just transferred to your phone.
You can now go back to the main menu and choose "reboot system now". It will ask you if you want to remove the auto recovery installation, do that.
That's all, you now have a clean and working Jelly Bean installation.
Someone else wrote down the same instructions if mine are not clear enough: http://forum.xda-developers.com/show....php?t=1785672
Click to expand...
Click to collapse
This prevented me from putting the stock image on the sdcard for flashing via CWM.
is there another way i can get this working, maybe via fastboot or via ODIN so i can return my friends phone.
Thank you.

Hi I had this problem to, mine was from a bad flash / bad firmware.
First I suggest http://forum.xda-developers.com/showthread.php?t=2284670 better recovery.
After from recovery
select factory reset, wipe cache, and from advance wipe dalvic cache.
then select mount usb, copy to card slim bean 3.1.0 http://www.slimroms.net/index.php/downloads/dlsearch/viewdownload/465-crespo/2505-slim-ns-3-1-0-official plus gaps http://www.slimroms.net/index.php/downloads/dlsearch/viewdownload/461-addonsfullpackages-412/2501-aio-addons, flash them in this order.
After first boot and config u can use http://www.wugfresh.com/nrt/ to write the OEM firmware.

Sorry this didn't work because nothing can be written to system and the sdcard is still not able to mount
Sent from my GT-N7100 using xda app-developers app

[Guide] Newbie to Photon Q 4G LTE Rooting w/ Ice Cream Sandwich

Purpose: The purpose of this guide is to help collect all information and steps needed to root a Motorola Photon Q 4G LTE and use Clockwork Mod. When I looked for tutorials there were no updated ones that detailed how to do this with the latest android update (as of May 2014) for the Photon. Some steps may have been / were copied from various posts & guides around the internet, again this is just a collection of information.
Goal: A user who just opened his Photon Q 4G LTE and did all the factory updates should be able to get his phone rooted by the end of the guide.
Note: I started this guide but sadly the ribbon cable on my Photon Q 4G LTE broke and I just decided to switch carriers. I never got back to proof reading this guide while it was still fresh in my memory but if anyone sees and issues just let me know.
Unlock the Bootloader:
I unlocked the bootloader because I wanted to install ClockWork Mod and read that you had to. Not sure if you need to do this just for root access. I wanted CWM so that I could create a backup of this phone as is came from the factory so if I want to restore down the road I can. Unlike my Samsung it seems difficult to find the factory software for the Photon Q so this seemed like the best way to get it. Also nice to have the ability to take backups of my phone every so often. Assuming your phone is new I recommend that you also take a factory backup once clockwork mod is on before installing any other apps.
1. Download and install the drivers for the Photon Q from Motorola here ( https://motorola-global-portal.custhelp.com/app/answers/detail/a_id/88481 )
2. Download this ZIP package which contains the tools you need for most of the steps here ( https://od.lk/f/MjRfMjc2MDc1Ml8 )
3. Head over to Motorola’s bootloader unlock site and sign in / register ( https://motorola-global-portal.custhelp.com/app/standalone/bootloader/unlock-your-device-b )
4. Put your device in fastboot mode by powering off, waiting a moment, then pressing the “power” and “volume down” buttons simultaneously and releasing the “power” button ONLY after a few seconds. Once you see the fastboot screen you can release “volume down” as well.
5. Unzip and open the folder with the ZIP files from Step 2 and open a command prompt or terminal (in Windows 7 hold “Shift” and right-click in the folder and select “open command window here”.
6. In the prompt, type “fastboot oem get_unlock_data” without the quotes.
7. You will see 5 or so lines with either “(bootloader)” or “INFO” in front of them. Use notepad or some other basic text editor to paste together the 5 lines of output into one continuous string WITHOUT (bootloader) or ‘INFO’ or white spaces in front of them so your string looks something like this: 0A40040192024205#4C4D355631323030373731363031303332323239#BD008A672BA4746C2CE02328A2AC0C39F951A3E5#1F532800020000000000000000000000
8. Check if your device can be unlocked by pasting the string in the field on Motorola’s page on their section 6. and click “Can my device be unlocked?” If you have a problem with this most likely the string you pasted in the box has spaces or extra / incorrect characters. Try again.
9. Open the email and get the unlock code. My email ended up in the “Promotion” category inbox instead of my normal inbox so if you don’t see it check in other places such as “Spam”.
10. Put your device in fastboot mode again by powering off, waiting a moment, then pressing the “power” and “volume down” buttons simultaneously and releasing the “power” button ONLY after a few seconds. Once you see the fastboot screen you can release “volume down” as well.
11. Connect the device to the computer with a USB cable. You'll get a confirmation message on the device to indicate that it's connected.
12. Open the folder with the ZIP files from Step 2 again and open a command prompt or terminal (in Windows 7 hold “Shift” and right-click in the folder and select “open command window here”.
13. In the prompt, type “fastboot devices” without the quotes and make sure your device shows up.
14. To unlock the bootloader, enter the following in the prompt “fastboot oem unlock UNIQUE_KEY” without quotes where you replace the “UNIQUE_KEY” with the code you received in the email. It is case-sensitive.
15. If the line was entered correctly, you will see a message confirming that your device was unlocked.​Install Clockwork Mod:
1. Download the latest ClockWorkMod recovery for the Photon Q from clockworkmod.com/rommanager and place the file in the same folder as the files from Bootloader Step 2. Be careful to select the right image!
2. Connect the Photon Q to the computer via USB.
3. Open the folder with the ZIP files from Bootloader Step 2 again and open a command prompt or terminal (in Windows 7 hold “Shift” and right-click in the folder and select “open command window here”.
4. Put your device in fastboot mode again by powering off, waiting a moment, then pressing the “power” and “volume down” buttons simultaneously and releasing the “power” button ONLY after a few seconds. Once you see the fastboot screen you can release “volume down” as well.
5. In the prompt, type “fastboot devices” without the quotes and make sure your device shows
a. If you don't see your device serial number, and instead see "<waiting for device>", fastboot is not configured properly on your machine. See fastboot documentation for more info.
b. If you see "no permissions fastboot", make sure your UDEV rules are setup correctly.
6. Flash ClockWork Mod recovery onto your device by entering the following command in the prompt “fastboot flash recovery image.img” without the quotes where “image.img” is the full name of the file you downloaded in Step 1.
7. Once the flash completes successfully, reboot the device into recovery to verify the installation by powering off the phone and then holding both “Volume Up” & “Power” simultaneously until you see ClockWork Mod on the screen. From here you can take a backup (recommended) if you want to like I did.
o Note: Some ROMs overwrite recovery at boot time so if you do not plan to immediately boot into recovery to install CyanogenMod, please be aware that this may overwrite your custom recovery with the stock one. ​Root the device:
1. Boot the Photon Q normally and go to Settings>Developer Options> and enable USB Debugging. You may have to turn on Developer Options as well if they are grayed out.
2. Connect the Photon Q to the computer via USB.
3. Navigate to the folder with the ZIP files from Bootloader Step 2 again open the run.bat file.
4. Press Enter after reading the disclaimer (if you want) and wait for the file to finish running.
5. After it is done you can press enter again to close the prompt and disconnect your phone
6. After the phone reboots automatically you will see a new Super User app in your app list. You are now rooted.​

FYI installing TWRP will offer to automatically root the device for you when you reboot back into Android.
Also, CWM for our devices is horribly outdated, and last I checked completely unable to flash any KK-based ROM. I wouldn't recommend it - OpenRecovery or TWRP are my recommendations.

arrrghhh said:
FYI installing TWRP will offer to automatically root the device for you when you reboot back into Android.
Also, CWM for our devices is horribly outdated, and last I checked completely unable to flash any KK-based ROM. I wouldn't recommend it - OpenRecovery or TWRP are my recommendations.
Click to expand...
Click to collapse
The two months I had my Photon Q working CWM worked great for me. Did a few backups and didn't have to re-root after each boot. But it always helps to have more options so thanks for mentioning both alternatives!

protivakid said:
The two months I had my Photon Q working CWM worked great for me. Did a few backups and didn't have to re-root after each boot. But it always helps to have more options so thanks for mentioning both alternatives!
Click to expand...
Click to collapse
I'm pretty sure CWM won't flash KK-based ROM's as I stated previously.
Also, you shouldn't have to re-root - TWRP just does the rooting for your if you are installing a custom recovery for the first time so you don't have to do it manually .

arrrghhh said:
I'm pretty sure CWM won't flash KK-based ROM's as I stated previously.
Also, you shouldn't have to re-root - TWRP just does the rooting for your if you are installing a custom recovery for the first time so you don't have to do it manually .
Click to expand...
Click to collapse
Thanks again! I just used the stock rom but rooted during my brief time with the phone but this will help those who wish to use KK on the Photon.

RISING THIS TREAD FROM THE DEAD!!!
WHO STILL HAS THIS PHONE WORKING??
i blue screened my LG G3 so i pulled this phone off my dash in the bimmer to possibly try to root but it runs so damn slow now. any support will be much appreciated this is by far the most reliable device i ever purchased (400 bucks out the door brand new fml)
i will try to root later this week but big shout out to XDA for all thier threads on android ive been rooting since the
optimus line
cheers!

Ulefone Power 6 Root

Hello. Has anyone rooted the Ulefone Power 6 yet? Im looking to have TWRP installed onto my new Power 6. My goal is to figure out a way to add user profiles, as it currently does not have them activated. I read online that you could edit the .prop to have any android activate the user profiles, but i cannot do this without my phone being rooted. Thanks in advance.

Start Here

Dvalin21 said:
Start Here
Click to expand...
Click to collapse
Sorry, This is for the original Ulefone Power, not the Power 6. Different phones. The instructions didn't lead me to anything useful. I have since update my phone to the latest firmware via the stock update app. I still haven't found a successful way to root the Power 6. There is this thread (https://www.getdroidtips.com/root-ulefone-power-6/), but the ADB commands to not work, and does not fastboot my phone to install the patched image. But either way, the instructions do not include a TWRP, so Im back to square one. HELP!

How to root Ulefone Power 6 (Build Power_6_SF1_V07) Updated 9/22/2019
OK. It was tough, but I finally found a way to root the Ulefone Power 6. I still haven't figured out a way to install TWRP, but that's because i have to build a custom recovery, and that's too advanced for me. So, anyone is welcomed to help out with building a custom recovery for TWRP. As for the root, This is what you will need:
Pre-Requirements:
Device battery charged up to 50%.
Developer Options enabled with OEM Unlocking and USB Debugging enabled
Remember to take a full backup of device data (Internal Storage, SMS), it will get formatted.
A Windows or Mac PC/Laptop is necessary to flash Magisk
A USB cable to connect your device with your PC
Download Links:
Download Minimal ADB Fastboot 1.4.3 (Portable). Extract it to your desktop.
It's best to give administrator privileges to the tools before you use them. To give them admin privileges:
Right click on adb.exe and select "Properties" at the bottom of the menu. Click on the "Compatability" Tab and check the "Run this program as an Administrator" box. Click on the "Apply" button and then the "OK" button to close the properties window.
Repeat the same process for the "cmd-here.exe" and the "fastboot.exe" files.
Ulefone USB Drivers. Extract it to your desktop and make sure you install the drivers.
MTK USB Drivers. Extract it to your desktop and make sure you install the drivers.
Latest Ulefone Power 6 Stock ROM. Or you could make a back up yourself. (latest rom as of 2/25/20 is GQ3081SF1_M860B1_Ulefone_20190921_V07(Non-EU) ).Extract it to your desktop.
MTK SP Multi Port Download Tool. This will be used to flash the most recent Ulefone rom on your device. Extract it to your desktop.
Download Magisk Manager
After downloading the Stock ROM (will be a .ZIP file), extract it to your PC.
Connect your device via USB cable
Find the "boot.img" file inside the Stock Rom folder you just extracted and copy only the "boot.img" file to your devices storage.
Copy Magisk Manager.apk to your devices storage
Using your device, install Magisk Manager
Open the Magisk Manager on your device.
Select "Install" from the first option next to "Magisk is not installed" and again select install.
Now, tap on "Select and Patch a File".
Go to your devices storage where you have copied the "boot.img" file earlier and select it.
Magisk will start patching the boot image.
Once the boot image is patched, Magisk will save the image on your "Download" folder located on your devices storage.
Locate the patched image (magisk_patched.img) and copy the "magisk_patched.img" to your PC. Make sure the patched image (magisk_patched.img) is inside the same folder as the extracted ADB and Fastboot tool folder on your desktop.
Open/run MTK SP Multi Port Download Tool
Click on File from the Menu located at the top right and select "Open Download Agent File"
Locate and select "MTK_ALLInOne_DA.bin", located in the same folder as the MTK SP Multi Port Download Tool folder.
Press the "Open buton" to select the file and close the window.
Now, click on the "Scatter File" button located at the top left.
Locate and select the XXXXXXXX_scatter.txt file located inside the extracted Ulefone Power 6 Stock Rom folder.
Press the "Open buton" to select the file and close the window.
Now, tick the "BootRom+PreLoader COM Sel All" check box located under the "scatter file" button.
Now, Click on the "Scan" button located at the bottom right.
Select Yes from the pop up window
Now, power off you device and disconnect your device from your PC by removing the USB cable from your device.
Now, reconnect the USB cable to your device while it is powered off.
MTK SP Multi Port Download Tool should detect your device and a green bar should appear confirming the connection with the words "Scan Success!" to the left of the green bar.
Press the "Stop all" button located at the bottom right
Disconnect and reconnect your device from your PC
Uncheck the "BootRom+PreLoader COM Sel All" box and check only the line with the green bar.
Click on the tiny "Start" button located to the right of the green bar.
You can confirm the flash was successful when the words "PASS" is visible to the right of the tiny "Start" & "Stop" buttons
Once the flashing is complete, you can close MTK SP Multi Port Download Tool and power on your device.
Configure your device to get to the home screen (skipping as many options as you can. You will have to format one more time) and enable Developer Options, OEM Unlocking and USB Debugging again.
Make sure your device is connected to your PC.
Now, you need to open up a command window (cmd window) inside the Minimal ADB Fastboot 1.4.3 (Portable) folder. To do this, open the "cmd-here.exe" file.
Next, enter the following command in the cmd window:
adb devices
(this command will confirm your device is connected to your PC via ADB )
Your device will show a pop up window asking for permission to connect via ADB. Click on the "Always Trust This Device" and Accept the connection
If successful, you should see the word "Device" to the right of your devices name on the list that the cmd window created.
Next, enter the following command:
adb reboot-bootloader
(This command will boot your device into fastboot/bootloader mode. It will turn off and the device will have a black lit screen)
Check that your device is connected to your pc by entering the following command:
fastboot devices
(this command will confirm your device is connected to your PC via fastboot/bootloader mode ) If successful, you should see the word "Device" to the right of your devices name on the list that the cmd window created.
Next, enter the following command:
fastboot flashing unlock
(if nothing happens, press the Volume up+ on your phone to start the unlocking of the bootloader)
(this will unlock your bootloader)
Next, enter the following command:
fastboot getvar unlocked
(this will confirm you have unlocked your bootloader. It will say "unlocked: yes")
Next, enter the following command:
fastboot flash boot magisk_patched.img
(This will replace your stock image with the patched image you created using Magisk Manager)
Next, enter the following command to reboot your phone:
fastboot reboot
Install magisk manager using your file manager. Make sure to follow directions when it asks you to give special permissions to install.
Open Magisk Manager and click on "OK" when it starts up and asks you for "additional setup".
Congratulations! Your device is rooted.
Extra notes:
If you come across a red watermark with the Chinese words and "Tee Keys" and/or "Google Keys" on the top right of your devices screen, this is how you fix it.
make sure your device is turned on and connected to your PC.
Open "cmd-here.exe" located in the Minimal ADB Fastboot 1.4.3 (Portable) folder.
Next, enter the following command:
adb shell pm uninstall -k --user 0 com.mediatek.factorymode
(This command will not do anything at the moment, but will remove the watermark after you reboot your device)
Next, enter the following command to reboot your device:
adb reboot
The watermark should be removed when your device restarts again.
ENJOY!

19Henry83 said:
OK. It was tough, but I finally found a way to root the Ulefone Power 6. I still haven't figured out a way to install TWRP, but that's because i have to build a custom recovery, and that's too advanced for me. So, anyone is welcomed to help out with building a custom recovery for TWRP. As for the root, This is what you will need:
. . . . .
. . . . . . . . . . .
. . . . . . . . . . . . . . .
ENJOY!
Click to expand...
Click to collapse
Thanks a heap for all these instructions, would not have been able to do this without them.
Just a few extra pieces of information for anyone else caryring out the above steps:
- If you your stock ROM doesn't have a file manager in order to open/execute the MagiskManager APK file then using Chrome to download the APK file will allow you to execute it.
- in the SP Multi Port Tool, after checking the line with the green bar and clicking start you'll notice the time in seconds counting next to the start button. At this point you may need to unplug your USB cable and replug it in order for the SP Multi Port Tool to detect the devices and actually start properly
- If the SP Multi Port Tool requires a checksum.ini file you can follow the instructions on the hovatek site (Google 'checksum.ini generatemediatek hovatek' I'm a new user so can't post links):
Note there is a download link for the CheckSum_Gen.zip file which will require you to register for an account on the hovatek website. You can create a junk/throw away account with a fake email as it doesn't require email confirmation. Also all of the files inside the CheckSum_Gen.zip folder need to be placed inside of the stock ROM folder where the scatter file is located.
- The watermark can only be removed after the MagiskManager carries out its additional setup and after root access is complete.

Still hoping to find a compatible TWRP recovery. If anyone builds one please let us know!

Hi, 19Henry83
I did try your method and it works great. I rooted my Power 6. The thing is I did this in hope to fix a freezing touchscreen issue. Touch screen frezzes and I need to lock/unlock my phone constantly to fix it. Now I'm convinced this is not a software issue and I will return the phone to the seller. So I wanted to get back to the original firmware. When I do that however there is still that red watermark and my IMEI is deleted. Is there any way to get back to the factory software and not have the red watermark, as I assume it will void my warranty.

I Need help please ,, I need the TWRP Recovery, Tool / Utility for the Ulefone Power 6, I have looked for it in many web pages and I cannot find it, all the ones I find have the same name "3.3.1 Power 6" and not It works for me when I install them, I get the same recovery that I had when I try to enter

jiroscop said:
Hi, 19Henry83
I did try your method and it works great. I rooted my Power 6. The thing is I did this in hope to fix a freezing touchscreen issue. Touch screen frezzes and I need to lock/unlock my phone constantly to fix it. Now I'm convinced this is not a software issue and I will return the phone to the seller. So I wanted to get back to the original firmware. When I do that however there is still that red watermark and my IMEI is deleted. Is there any way to get back to the factory software and not have the red watermark, as I assume it will void my warranty.
Click to expand...
Click to collapse
Hello Jiroscop. I had the same problem and only noticed after i read your post. Now, a couple months later, i managed to use an IMEI changer to insert my IMEI found on my original box where my phone came in. It should have two IMEIs. I don't know if i can explain on this forum. Try researching it on your own and get back to me if you cannot find a way to fix your phone.
NOTE: you will need your original IMEI's, changing the IMEI's with anything other than the original ones will brick your phone.