Moto G, currently running 4.4.2 unlocked and rooted with TWRP v2.6.3.0 the firmware is tweaked to my liking with GravityBox. I am also using the Faux123 to over/under clock etc.
Very happy with the performance, features and battery life.
But I am now getting bugged by the Motorola update for 4.4.3
I did try to update and the phone got into a start, reboot loop. So I have restored to my last configuration.
It's been quite sometime since I played with configuring the above and I have gone a bit blank! Can someone please outline the steps that I have to do to complete the upgrade with minimum fuss.
As a side note. I have avoided custom ROMs so far because of all the problems that I was reading about several months ago. But perhaps enough time has elapsed for me to consider going say CM11 now? I would appreciate any comments as to me going down this route. ie. Are all bugs worked out is the Moto G fully functional, does a custom ROM truly provide worthwhile benefits?
Thanks.
I would also like to know this as well as I am currently on 4.4.2 unrooted, but really feel feel like I want to start and get my Moto G rooted and up and running with all the goody's available on the community, but feel like I should wait for the 4.4.3 rollout before I start going through the whole bootloader unlocking, rooting etc.
So I will check back on this post, and thank you to the thread starter as this saves me starting a similar topic.
Rooted 4.4.2 over here as well. Unfortunately I've had no such luck finding a way to update to 4.4.3 while being rooted. I've been through a plethora of guides and suggestions but nothing seems to be working. I'll end up getting an error no matter what I do.
Don't mean to try and hijack your thread, but I've been trying to flash the .zip for the update with both CWM and TWRP but I get an error every time. Anyone have any ideas why? Do I need to configure root-requiring apps beforehand or something?
ugh...same here! Please someone figure this out!
@Kwala Baerr I was hoping for a quick 1,2,3 Guide! I miss posted the question in the General section, then moved it here. I subsequently find a few similar posts in this section. But your message suggests that you may have already tried them which worries me! Anyway I will have a go tomorrow and post here if I get success.
Sent from my Nexus 7 using Tapatalk
@grahamgo oh yea sorry. Well I've tried just about everything. I think I've narrowed down my problem to SoftKeyz messing up my SystemUI.apk so you might still have a chance. Let me know how it goes though!
grahamgo said:
Moto G, currently running 4.4.2 unlocked and rooted with TWRP v2.6.3.0 the firmware is tweaked to my liking with GravityBox. I am also using the Faux123 to over/under clock etc.
Very happy with the performance, features and battery life.
But I am now getting bugged by the Motorola update for 4.4.3
I did try to update and the phone got into a start, reboot loop. So I have restored to my last configuration.
It's been quite sometime since I played with configuring the above and I have gone a bit blank! Can someone please outline the steps that I have to do to complete the upgrade with minimum fuss.
As a side note. I have avoided custom ROMs so far because of all the problems that I was reading about several months ago. But perhaps enough time has elapsed for me to consider going say CM11 now? I would appreciate any comments as to me going down this route. ie. Are all bugs worked out is the Moto G fully functional, does a custom ROM truly provide worthwhile benefits?
Thanks.
Click to expand...
Click to collapse
Put on your phone Us firmware http://forum.xda-developers.com/showthread.php?t=2542219 setup the phone via wifi. Update is about 163mb. After that use Mototool to root the phone and fix the white screen http://forum.xda-developers.com/showthread.php?t=2635706
mabey you can do a beckup of sms https://play.google.com/store/apps/details?id=com.riteshsahu.SMSBackupRestore and https://play.google.com/store/apps/details?id=com.riteshsahu.CallLogBackupRestore
regards
I recently upgraded my stock rooted 4.4.2 Moto G to 4.4.3. The steps you have to take depends on how many modifications you've made. But basically, you need to make sure of these things:
Do a nandroid backup of your working system!
What I did:
Uninstall Xposed modules and Xposed Framework. You *must* do this through the XPosed installer itself.
Re-install/Re-enable system apps that you disabled. For me, I used Titanium Backup, and unfroze the apps that I froze. I made a mistake on my Nexus 7 and uninstalled without backup, which made this process harder.
Repeat the same for any other root apps that made changes to your /system folder.
Uninstall Busybox. If you don't know if you have it or not, download this BusyBox Installer app, and it will tell you. If it is installed, go to the bottom right of your screen and under its preferences, there is a 'delete busybox' option as seen in their 6th screenshot. The order of this is important! Some apps require BusyBox to work and do their installing/uninstalling.
Completely unroot by going to SuperSU's Settings tab, and selecting the Full Unroot option.
Download the latest version of SuperSU onto your SD card if you don't have it already.
Download 4.4.3 update and let it install.
Go into your recovery and re-install SuperSU.
Restore your old root apps like XPosed and BusyBox. I re-installed them and re-did my settings for gravity box and saved my settings using the in-app options for XPrivacy, but you might be able to use Titanium Backup for this if your settings are too extensive.
Alternately, if you're having trouble because you can't find the system apps you need or you're getting an error while updating due to something in your /system folder, you should download stock 4.4.2, extract it, and then re-flash the stock system & boot.img using fastboot or mfastboot. For my XT1034, it was in these images: system.img_sparsechunk1, system.img_sparsechunk2, system.img_sparsechunk3 + boot.img. Yours may differ depending on your model.
Note, I did not test this particular method when I upgraded, but I did use mfastboot to revert to a complete stock 4.4.2 when I changed from CM11 awhile back using this guide.
I was able to keep my bootloader unlocked, and to keep PhilZ's recovery through the update process with no issues.
Hope that helps!
tarotsujimoto said:
I recently upgraded my stock rooted 4.4.2 Moto G to 4.4.3. The steps you have to take depends on how many modifications you've made. But basically, you need to make sure of these things:
Do a nandroid backup of your working system!
What I did:
Uninstall Xposed modules and Xposed Framework. You *must* do this through the XPosed installer itself.
Re-install/Re-enable system apps that you disabled. For me, I used Titanium Backup, and unfroze the apps that I froze. I made a mistake on my Nexus 7 and uninstalled without backup, which made this process harder.
Repeat the same for any other root apps that made changes to your /system folder.
Uninstall Busybox. If you don't know if you have it or not, download this BusyBox Installer app, and it will tell you. If it is installed, go to the bottom right of your screen and under its preferences, there is a 'delete busybox' option as seen in their 6th screenshot. The order of this is important! Some apps require BusyBox to work and do their installing/uninstalling.
Completely unroot by going to SuperSU's Settings tab, and selecting the Full Unroot option.
Download the latest version of SuperSU onto your SD card if you don't have it already.
Download 4.4.3 update and let it install.
Go into your recovery and re-install SuperSU.
Restore your old root apps like XPosed and BusyBox. I re-installed them and re-did my settings for gravity box and saved my settings using the in-app options for XPrivacy, but you might be able to use Titanium Backup for this if your settings are too extensive.
Alternately, if you're having trouble because you can't find the system apps you need or you're getting an error while updating due to something in your /system folder, you should download stock 4.4.2, extract it, and then re-flash the stock system & boot.img using fastboot or mfastboot. For my XT1034, it was in these images: system.img_sparsechunk1, system.img_sparsechunk2, system.img_sparsechunk3 + boot.img. Yours may differ depending on your model.
Note, I did not test this particular method when I upgraded, but I did use mfastboot to revert to a complete stock 4.4.2 when I changed from CM11 awhile back using this guide.
I was able to keep my bootloader unlocked, and to keep PhilZ's recovery through the update process with no issues.
Hope that helps!
Click to expand...
Click to collapse
What recovery were you on?
Kwala Baerr said:
What recovery were you on?
Click to expand...
Click to collapse
Here's the thread with information on downloading & installing PhilZ Touch recovery:
http://forum.xda-developers.com/showthread.php?t=2639583
Looks like there's a new stable release out, but I still had PhilZ Touch 6.26.6 Falcon installed.
tarotsujimoto said:
I recently upgraded my stock rooted 4.4.2 Moto G to 4.4.3. The steps you have to take depends on how many modifications you've made. But basically, you need to make sure of these things:
Do a nandroid backup of your working system!
What I did:
Uninstall Xposed modules and Xposed Framework. You *must* do this through the XPosed installer itself.
Re-install/Re-enable system apps that you disabled. For me, I used Titanium Backup, and unfroze the apps that I froze. I made a mistake on my Nexus 7 and uninstalled without backup, which made this process harder.
Repeat the same for any other root apps that made changes to your /system folder.
Uninstall Busybox. If you don't know if you have it or not, download this BusyBox Installer app, and it will tell you. If it is installed, go to the bottom right of your screen and under its preferences, there is a 'delete busybox' option as seen in their 6th screenshot. The order of this is important! Some apps require BusyBox to work and do their installing/uninstalling.
Completely unroot by going to SuperSU's Settings tab, and selecting the Full Unroot option.
Download the latest version of SuperSU onto your SD card if you don't have it already.
Download 4.4.3 update and let it install.
Go into your recovery and re-install SuperSU.
Restore your old root apps like XPosed and BusyBox. I re-installed them and re-did my settings for gravity box and saved my settings using the in-app options for XPrivacy, but you might be able to use Titanium Backup for this if your settings are too extensive.
Alternately, if you're having trouble because you can't find the system apps you need or you're getting an error while updating due to something in your /system folder, you should download stock 4.4.2, extract it, and then re-flash the stock system & boot.img using fastboot or mfastboot. For my XT1034, it was in these images: system.img_sparsechunk1, system.img_sparsechunk2, system.img_sparsechunk3 + boot.img. Yours may differ depending on your model.
Note, I did not test this particular method when I upgraded, but I did use mfastboot to revert to a complete stock 4.4.2 when I changed from CM11 awhile back using this guide.
I was able to keep my bootloader unlocked, and to keep PhilZ's recovery through the update process with no issues.
Hope that helps!
Click to expand...
Click to collapse
Im rooted running stock rom and using exposed installer with gravity box and a few other modules running and all I had to do to update to 4.3.3 was to use Moto Tool AIO v3.0 to revert back to stock kitkat recovery, after that I just accepted the update, installed it, and then went back to a custom recovery. I lost none of my exposed installs or settings, took maybe 10 minutes start to finish and was painless.
tarotsujimoto said:
Here's the thread with information on downloading & installing PhilZ Touch recovery:
http://forum.xda-developers.com/showthread.php?t=2639583
Looks like there's a new stable release out, but I still had PhilZ Touch 6.26.6 Falcon installed.
Click to expand...
Click to collapse
I have just wasted a lot of time...... I tried Philz Touch 6.43.8, no go, then an earlier version, still no go. Then I found a thread saying that there were bugs in later versions, they recommended the use of 6.26.6
I tried it and it works great. However I wasted almost 2 hours finding this out.
castuis said:
Im rooted running stock rom and using exposed installer with gravity box and a few other modules running and all I had to do to update to 4.3.3 was to use Moto Tool AIO v3.0 to revert back to stock kitkat recovery, after that I just accepted the update, installed it, and then went back to a custom recovery. I lost none of my exposed installs or settings, took maybe 10 minutes start to finish and was painless.
Click to expand...
Click to collapse
I appreciate @tarotsujimoto post and I see the logic of this approach. But I too was thinking that it might be less troublesome (but maybe take longer) to go back to factory, update it to 4.4.3 and then re-install Xposed and apps + data, etc using Titanium.
@castuis I am intrigued by your mention of using a custom recovery. Could you please expand on what you backed up and if possible more details on how you did it etc.
I have wasted too much time today getting a working Philz Touch going, (maybe I should have stayed with TWRP!). But I do like the look of Philz 6.26.6 now its working. But will have to put my 4.4.3 update attempt off for a day or so.
Thanks!
Since none of the methods mentioned works for me, I have tried to extract the system.img from the original ROM archive. But how do I mount that system.img_sparsechunk files on Linux? They can not be converted by simg2img or unyaffs either ...
I had no success with any of the "short cut" methods either. I was hoping that @castuis promise of a 10 minute method would come true, but he hasn't been back to expand on his method. I myself reverted the phone to factory, let it upgrade. Then re-rooted, installed xposed and then let Google play reinstall my apps. It's definitely not a quick method. But at least it gave me a clean install. Significant frustration, caused by using Philz touch, but switched to TWRP. Finally did a system backup with Titanium. I thought that was it. Now it looks like there will be a 4.4.4 soon. I'm thinking to ignore it and wait for the next upgrade. @nodh I would wait for 4.4.4 !
Sent from my Nexus 7 using Tapatalk
I've solved my upgrade problem: I've flashed the 176.44.1 (retail Germany, 4.4.3) stock ROM, as described here. Altough I didn't flash the recovery (to restore root with the ClockWorkMod recovey) and didn't erase userdata. Now I've got the upgrade, with all my settings preserved and even rooted again.
Hi Guys
After one of the custom 5.1 roms crashed and left me without the phone, I have decided that I will go live with Marshmallow.
I have installed the original stock 6.0 MRA58K which after booting quickly went into MRA58N with OTA update.
Once I have realised how many things I am missing in my phone, due to using the stock ROM, I was looking for a perfect solution and decided that I will no longer be flashing custom ROMs, but use XPOSED as a framework with additional modules.
I have installed the elementalx kernel and added the correct XPOSED framework.
Everything was working fine until yesterday, where I have received notification about OTA update to 6.0.1.
First I thought that I don't really care about emojis, however I do like the option of "Do not disturb until next alarm".
I know that I can achieved by some additional modules to the xposed, however the OTA update is quite annoying.
Because I was on TWRP as a recovery, I have also installed the BusyBox and SimpleRecoverySwitch hoping that this will resolve the issue. Quickly reflashed stock recovery (don't know why, but every time when I was using fastboot to flash recovery with stock recovery.img, TWRP was still there) and found that I still can't use OTA update to 6.0.1. due to error:
"app_process 32 has unexpected contents".
After googling I have found that this is because I have xposed up and running.
Googled than for "unistalling" xposed and found plenty of topics, however none of them have provided me clear answers, especially to the question of "how to uninstall xposed". I have not found any original.img, so I suppose xposed installer have not created any backup, also when I will open xposed Installer - options to "uninstall xposed" are greyed out.
So my question would be - how can I easily remove xposed (temporary) without loosing data/restarting fully the phone, because after 5 days of flashing/reflashing/factory resets I am slowly tired from setting up personal configuration on my phone (even when on Marshmallow is much more easier than on lollipop 5.1).
If this is not possible, how I could remove OTA update from not only notifying me all the time, but also not restarting the phone (wakelock?)
Once you root the phone, you will not be able to upgrade via OTA. Your choices are to follow the instructions on this thread or to completely go back to stock without root and do the OTA.
Guys, every time I try to install Xposed for my SM-G920F (I´m 100% sure that I use the correct files every time), my device reboots after entering the pin code.
I had already flashed stock a completely new stock rom via Odin, Wiped Data/Factory Reset and installed XtreStoLite newest version.
Nothing helps.
I remember I did something wrong with "Kernel Auditor" in the past. (I think I done something with "Enable on Boot") Since then my device reboots every time I install Xposed.
I hope someone does have another Idea, I really miss xposed
Flash arter97 twrp recovery and kernel. Then flash wannam version of exposed for lollipop/ marshmallow.. And cheers*
kforkai said:
Flash arter97 twrp recovery and kernel. Then flash wannam version of exposed for lollipop/ marshmallow.. And cheers*
Click to expand...
Click to collapse
Thanks for the help mate, I followed your steps but still not working.
Xposed is installing successfull, but after I activate some xposed modules like Amplify or xTouchwiz the device reboots immediately.
I really don´t know what´s causing that.
Any other help, Im really pissed right now (sorry)
memocatcher said:
Thanks for the help mate, I followed your steps but still not working.
Xposed is installing successfull, but after I activate some xposed modules like Amplify or xTouchwiz the device reboots immediately.
I really don´t know what´s causing that.
Any other help, Im really pissed right now (sorry)
Click to expand...
Click to collapse
Im using sm-g929i mm6.0.1
Amplify doind good overe here. I coulndt get pass the samsung logo When I installed both xtouchwiz and xprivacy at the same time. Enabled both modules and the hp.
Solved that by pressing vol down, home and power. Release right away when the phone restarted.
I have a question. I want to root my phone (upgraded from oreo to pie, stock), but i'm not sure what should i do. Should i use oreo rooting instructions? I can't find any tutorial for rooting on pie. I don't want to change my rom, i just want to have a root and be able do use the magick and modules that's all. It would be nice to have step by step instruction.
I know i have to unlock my bootloader first at htcdev, then install twrp (not sure which twrp and if the installation is same as on oreo?)
In the past i rooted one phone but it was completely different and i almost bricked my device, because some idiot posted wrong link on the forum... There is so many versions of everything and i'm feeling lost in it.
I hope this helps, but Pie is still very new for the HTC U11. Some even are saying that clean flashes of the Pie RUU have flash, camera, and wifi issues. I am currently running the amazing RR-P rom (which is based on pie), but it runs on the latest Oreo RUU. I have no issues with the ROM and I get insane SoT even without battery savings. I am excited for the future of this phone, since I love the hardware navbar (never liked the on-screen one / though my HTC m8 is still a boss, and even the forums there have a very solid Lineage 17.0 (android 10) working on it).
https://dl.twrp.me/ocn/
Above is the official link to the US HTC u11 TWRP recoveries. I don't think (to be safer than sorry) these are 100% compatible over the PIE firmware though.
I checked HTCdev, and it doesn't seem to have any difference in the instructions in unlocking the bootloader. No mention of Nougat or Oreo, so I would assume there's no difference in doing the same with Pie.
I flashed my U11 after Pie update, working fine, no problems with flash, wifi or anything else (CID: HTC__034)
1. Unlock bootloader via htcdev
2. Flash latest TWRP from the official site. Instructions here for example: https://www.xda-developers.com/how-to-install-twrp/
3. Flash Magisk (also from official Magisk site)… that was a little trickier, since TWRP can't mount the encrypted partitions. The workaround is to copy the Magisk ZIP onto an SD Card and flash it from there while in TWRP.
4. Enjoy.
I decided to root this U11 for the first time, since I don't expect any futur software updates coming form HTC.
Thank you for all your help, i'll try this out today. :good:
So i did everything and it's working but i have one problem. After installing magisk i tried to install some modules, and one of them caused bootloop and i was unable to delete it, and also i was unable to install module uninstaller (fail). So i had to do factory reset - any solution to avoid this kind of problems in future?
Also i installed xposed successfully, but none of modules was working..
Togzyk said:
So i did everything and it's working but i have one problem. After installing magisk i tried to install some modules, and one of them caused bootloop and i was unable to delete it, and also i was unable to install module uninstaller (fail). So i had to do factory reset - any solution to avoid this kind of problems in future?
Also i installed xposed successfully, but none of modules was working..
Click to expand...
Click to collapse
I have no answers, but as u can see a rooted pie is problematic, hence the many people reverting back to oreo and or nougat, but some people somehow make it work. Not me I could not downgrade quick enough after rooting, unrooted pie worked great, but my many 'need for root apps' did not , so back to oreo for me . Just my 2 cents!! Good luck.
hammered58 said:
I have no answers, but as u can see a rooted pie is problematic, hence the many people reverting back to oreo and or nougat, but some people somehow make it work. Not me I could not downgrade quick enough after rooting, unrooted pie worked great, but my many 'need for root apps' did not , so back to oreo for me . Just my 2 cents!! Good luck.
Click to expand...
Click to collapse
I found many working apps. The biggest problem is "substratum", especially when it comes to changing navbar buttons. But gravitybox is working, and I'm happy with it. Thanks for your help
My rooted Pie works fine, but I didn't install Substratum or Xposed.