YOUR WARRANTY IS NOW VOID. USE IT AT YOUR OWN RISK! I AM NOT RESPONSIBLE FOR ANY DAMAGES OR BRICKS THAT MIGHT HAPPEN UPON FLASHING. YOU HAVE BEEN WARNED!!!
REQUIREMENTS
Download Flashfile
D820s_LOLLIPOP_TW (TAIWANESE FIRMWARE), Build 1.
14.709.1 - Supports Asian Languages
D820s_LOLLIPOP_WWE (EUROPE WORLD WIDE ENGLISH FIRMWARE), Build 1.20.401.1 - Supports European Languages and Arabic
Download SP Flashtool
SP-Flash-Tool-v5.1532.00
Download Pgfs
Pgfs
Desire 820s with at least 50% battery power
A good working PC that is capable of holding battery power for at least 15 minutes in case of any power outages
A good working USB Cable
Manually install USB VCOM drivers using this tutorial. (If you have already installed the drivers then skip this step)
Internet connection for automatic update of VCOM and Preloader drivers
Familiarity with SP Flash Tool. If you do not know how this tool works, then I advice you to just stay away from using it. It is not a custom recovery and can cause a hard brick if you misuse it
Confirmed to be working on Desire 820ts, us and ys variants
Please know that you will not be able to install any OTA for this firmware because it is not the original firmware for your device.
REMEMBER This is a full firmware flash and not just a ROM so you MUST know how to revert to your original firmware in case of repairs by warranty.
This Procedure will format your Internal SD Card so please backup before proceeding
HOW TO FLASH WITH SP FLASH TOOL
1. Extract the Downloaded Lollipop Flashfile
2. Extract the Unlocked Pgfs and copy pg1fs and pg2fs into the firmware folder
3. Extract SP-Flash-Tool-v5.1532.00.zip and launch flash_tool as Administrator
4. Click on Scatter-loading by the right
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
4. In the window that pops up, select MT6752_Android_scatter in the Lollipop Flashfile folder
6. A list with ticked boxes should appear in SP flash tool
7. Select Firmware Upgrade
7. Click Download
9. Stop should now be prominent while other options should be grayed out
10. Switch off your phone and wait for at least 10 seconds after it has switched off
12. Connect the switched off phone to the PC via USB cable
13. A progress bar should start running
14. DO NOT INTERRUPT. Wait until you get a Success message (green circle with OK)
15. Disconnect USB cable and switch on the phone
To unlock bootloader see post #2
CREDITS
@nkk71 for flawlessly decrypting both the Taiwanese and European RUUs. We owe you a great load of gratitude. We salute you :highfive:
@Mohamed Yaser for testing the RUUs on the Desire 820s Dual sim, among many other contributions he has made :good:
@Nc.netcat for providing unlocked pgfs
@patrol31
To Unlock the bootloader use these pgfs files
(Just replace the pgfs files in firmware folder and load scatter file and tick pg1fs and pg2fs only)
Unlocked pgfs
To lock bootloader flash these pgfs
Locked pgfs
STOCK KITKAT FIRMWARE LINKS
Desire 820s
(Please Note that to flash Kitkat you have to press and hold the volume up button while connecting the phone to the PC and let go when flashing begins)
Official HTC RUUs
0PGZIMG_A50ML_DTUL_L50_DESIRE_SENSE70_hTC_Asia_TW_1.20.709.1_Radio_1514P2.P02.0501.0506_release_452399_signed_2_4.zip
0PGZIMG_A50ML_DTUL_L50_DESIRE_SENSE70_HTC_Europe_1.20.401.1_Radio_1514P2.P02.0501.0506_release_453730_combined_signed.zip
Screenshots
Nice One
Mohamed Yaser said:
Nice
---------- Post added at 04:22 PM ---------- Previous post was at 04:21 PM ----------
I will delete mine now whats ur upload progress?
Click to expand...
Click to collapse
5 hours to go bro
Gibz97 said:
5 hours to go bro
Click to expand...
Click to collapse
Good Luck , i wish we root it
we need a permissive kernel , and a good recovery Out TWRP still needs some work
Mohamed Yaser said:
Good Luck , i wish we root it
we need a permissive kernel , and a good recovery Out TWRP still needs some work
Click to expand...
Click to collapse
You can upload yours too. Mine will take quite some time.
TWRP ported successfully. Just some minor fixes needed, Rooted now..
im waiting for the rom to be uploaded. will test it to my D820ts. cant wait
nice :good::good:
just dropped in to say congrats
1. Incase the phone is soft bricked during this process can we go back to stock kitkat rom with stock recovery?
2. Will we be able to do OTA update incase if HTC decide to realease any OTA updates in future with this rom?
Gibz97 said:
CREDITS
@nkk71 for flawlessly decrypting both the Taiwanese and European RUUs. We owe him a great load of gratitude. We salute you man :highfive:
@Mohamed Yaser our dev for testing the RUUs on the Desire 820s Dual sim, among many other contributions he has made :good:
Click to expand...
Click to collapse
my pleasure, I'm glad you got things up and running
nice job :good::good:
smartpal said:
1. Incase the phone is soft bricked during this process can we go back to stock kitkat rom with stock recovery?
2. Will we be able to do OTA update incase if HTC decide to realease any OTA updates in future with this rom?
Click to expand...
Click to collapse
It is not just a ROM, it is a full firmware so yes you will receive OTA updates if the carrier releases them. To revert to lollipop you will have to reflash the full Kitkat firmware with SP Flash Tool here
nkk71 said:
nice :good::good:
just dropped in to say congrats
Click to expand...
Click to collapse
U rock
Mohamed Yaser said:
U rock
Click to expand...
Click to collapse
OMG! the upload has just restarted. It was at 89%.
BTW did you flash the Taiwanese or European RUU?
Gibz97 said:
OMG! the upload has just restarted. It was at 89%.
BTW did you flash the Taiwanese or European RUU?
Click to expand...
Click to collapse
Are you kidding? :laugh:
You start again uploading? :laugh:
Gibz97 said:
OMG! the upload has just restarted. It was at 89%.
BTW did you flash the Taiwanese or European RUU?
Click to expand...
Click to collapse
I know what you mean
same thing happened to me uploading to mega; it's great, but not resumable it seems, unless i missed something
but if you're going to be continuing this, i can highly recommend androidfilehost.com
and use ftp for uploads (those are resumable)
European i think
And i didnt recevie ota may be due to my region
Whats ur eta gibz
---------- Post added at 08:10 PM ---------- Previous post was at 08:06 PM ----------
nkk71 said:
I know what you mean
same thing happened to me uploading to mega; it's great, but not resumable it seems, unless i missed something
but if you're going to be continuing this, i can highly recommend androidfilehost.com
and use ftp for uploads (those are resumable)
Click to expand...
Click to collapse
Ther's no resume in Afh
Have been using it for rom projects "venom and lean " on nexus devices
Mohamed Yaser said:
Ther's no resume in Afh
Have been using it for rom projects "venom and lean " on nexus devices
Click to expand...
Click to collapse
yes there is, but you have to ask for it
EDIT: ie, you have to ask for FTP access
nkk71 said:
yes there is, but you have to ask for it
EDIT: ie, you have to ask for FTP access
Click to expand...
Click to collapse
I have ftp acces already but if network gone and you resume ***gives currpted zip
Mohamed Yaser said:
I have ftp acces already but if network gone and you resume ***gives currpted zip
Click to expand...
Click to collapse
OP, sorry for the off topic
@Mohamed Yaser
I've been uploading to afh for quite a while, i can disconnect (or get disconnected) for several days, and still resume my uploads
better check your settings and/or ftp client
Related
Official Final GingerBread RUU Released
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thunderbolt owners have been waiting a long while to get Gingerbread -- too long, considering this phone was once Verizon's flagship. We've seen several leaked builds come around, all of which experienced a variety of problems. The most recent leak seemed to be the most stable so far, but it was still chock-full of annoying little bugs.
Fortunately, we've gotten a hold of a newer build (2.11.605.5) that fixes a lot of the issues from the 605.3 build, so HTC is clearly heading in the right direction.
Here's a summed up version of what's new in this build:
• HTC Logger removed
• Voicemail notification fixed
• Front facing camera/Gtalk fixed
• MMS/SMS Fixes
• Weather syncing fixes
• ...and more
Sound good? I thought it might. Head below for download and installation instructions.
Click to expand...
Click to collapse
Installation Instructions
• After downloading it, rename it to "PG05IMG.zip"
-Note: If you're doing this from a Windows machine, make sure you don't rename the file "PG05IMG.zip.zip," as Windows hides known file extensions by default.
• Drop the file on the root of the SD Card
• Turn off your device
• Hold Volume Down + Power to reboot into the bootloader -- the file should automatically be detected and the flashing process will begin.
• Wait for your device to complete the process and reboot
Click to expand...
Click to collapse
Source
Download (RUU)
Mirror 1
Mirror 2
Mirror 3
Mirror 4
Download (Rooted/Odex)
Download (Rooted/Deodexed/Zipaligned)
I assume it's not rooted? And if not, can it be rooted w/ revolutionary?
jv
johnnyv5 said:
I assume it's not rooted? And if not, can it be rooted w/ revolutionary?
jv
Click to expand...
Click to collapse
Follow these steps to achieve root:
1) Wipe data, cache, and dalvik (this will erase all your data so backup anything before this step)
2) Download Thunderbolt_Patched_hboot.zip from XDA by Shadowmite.
3) Open Thunderbolt_Patched_hboot.zip, you should see PG05IMG.zip inside. Take PG05IMG.zip and place it in the root of your microSD card. Reboot into Hboot.
4) It should detect PG05IMG.zip. Just install it. Then delete PG05IMG.zip
5) Download full RUU (from link in the OP) and rename the file to PG05IMG.zip and place it in the root of your microSD card (will lose root and clockworkmod).
6) Reboot into HBoot (Hboot should say UNLOCKED--highlighted in pink), it should detect PG05IMG.zip, install it, then delete PG05IMG.zip.
7) Download Clockworkmod (CWR5.0.2.1)PG05IMG.zip)
8) Rename the clockworkmod download to PG05IMG.zip. Place on root of your microSD card.
9) Reboot into HBoot, it should detect PG05IMG.zip, install it, then delete PG05IMG.zip. Now you have Clockworkmod.
10) Lastly, install Superuser (su-3.0.5-efgh-signed.zip) by downloading it from here. Place the file on your microSD and install Superuser from Clockworkmod. Reboot.
You are now flashed to the latest ROM, with root access, and clockworkmod.
How could I back up my app data if I'm not rooted?
Root is important to me, but not critical. I am installing this and then I will attempt the Revolutionary root method and report back ASAP.
Wait, how do you know this is the "final" build thats being released as an OTA update... has that process already started for some?
Sorry but another dumb question, if you are already rooted with Revolutionary shouldn't it block this RUU from overwriting hboot? I have old school root and my wife's tbolt has revolution.
jv
Finally! I'm curious where this was "found" though. Any ideas on when an official OTA might come in?
So far no rollout, at least not according to http://support.verizonwireless.com/system_update/thunderbolt.html. Still says it is coming soon. Curious if this is another "test" build like 605.0 and 605.1 were or if this is the one that will roll out. The update instructions on the vz site still have the picture showing 605.3 and the size of the .3 update, so that hasn't been updated either. Guess we will see in a couple days. In any case, thanks for the drop! It'll give me something to play with in the mean time.
rajuabju said:
Wait, how do you know this is the "final" build thats being released as an OTA update... has that process already started for some?
Click to expand...
Click to collapse
My mistake I didn't mean to say final (this is not a confirmed OTA yet). I have changed the title.
johnnyv5 said:
Sorry but another dumb question, if you are already rooted with Revolutionary shouldn't it block this RUU from overwriting hboot? I have old school root and my wife's tbolt has revolution.
Click to expand...
Click to collapse
Flashing an RUU will overwrite any previous HBoot you have unless you flash the patched HBoot I provided. That HBoot will never be rewritten and will remain unlocked even after full RUU flashes. I am not sure if Revolutionary already has this HBoot incorporated or uses the unlocked/unpatched version but I would recommend to follow the steps above and flash the patched HBoot so you won't have to worry.
johnnyv5 said:
Sorry but another dumb question, if you are already rooted with Revolutionary shouldn't it block this RUU from overwriting hboot? I have old school root and my wife's tbolt has revolution.
jv
Click to expand...
Click to collapse
Yes
Sent from my ADR6400L using xda premium
New ROM works great and is easily rootable via Revolutionary method. Cheers!
system6 said:
New ROM works great and is easily rootable via Revolutionary method. Cheers!
Click to expand...
Click to collapse
so if i am rooted i can just install this rom and root with revolution? we don't have to worry about creating bricks?
kidhudi said:
so if i am rooted i can just install this rom and root with revolution? we don't have to worry about creating bricks?
Click to expand...
Click to collapse
I can't promise anything there, but it worked for me. I just downloaded the SU file and ran it in recovery.....and ROOTED AGAIN.
It was that easy.
kidhudi said:
so if i am rooted i can just install this rom and root with revolution? we don't have to worry about creating bricks?
Click to expand...
Click to collapse
Please be advised that the Revolutionary tool does not actually root your device. It only flashes the HBoot to an unlocked S-OFF version and optionally flashes Clockworkmod recovery. In order to gain root, must follow step 10 of the method I posted here: Link. After that you should be all set.
Why not wait till its deodexed ...probably by the end of the day.
open1your1eyes0 said:
Please be advised that the Revolutionary tool does not actually root your device. It only flashes the HBoot....
Click to expand...
Click to collapse
Now you're just going to confuse people !!
---------- Post added at 03:32 PM ---------- Previous post was at 03:30 PM ----------
ponyboy82 said:
Any ideas on when an official OTA might come in?
Click to expand...
Click to collapse
No one here knows (unless they work in VZW's engineering or related group). If someone posts a date, take it with a grain of salt.... How many updates have EVER been released on time ?
hallstevenson said:
Now you're just going to confuse people !!
---------- Post added at 03:32 PM ---------- Previous post was at 03:30 PM ----------
No one here knows (unless they work in VZW's engineering or related group). If someone posts a date, take it with a grain of salt.... How many updates have EVER been released on time ?
Click to expand...
Click to collapse
Very true, on both counts. Point taken. So... maybe another year or so for VZW to push this out?
ponyboy82 said:
Very true, on both counts. Point taken. So... maybe another year or so for VZW to push this out?
Click to expand...
Click to collapse
Im betting 2 weeks after ICS code is released
Any bets on if restoring data will hose it? anyone, anyone?
Hello! I started this thread as it seems it's too hard for lot of people to search for guides about flashing. This is a way to get rid of useless posts like: "What is flashing?" "How to flash?" "Can I haz a cheezeburger?" Be grateful
DISCLAIMER: I am not responsible of any issues you might have by using my guide. Flashing always includes a risk of bricking your device. Dont come to cry. You've been warned!
The list of ROMs can be found HERE
-Download ODIN Multidownloader 4.43. Link: http://www.megaupload.com/?d=W6CMP1LA
-After it has downloaded, extract it anywhere u want (i suggest desktop, easier)
-RUN ODIN.
-Power off your phone.
-Put your phone into downloading mode. Hold together: Power+Volume Down+Home (phone boots to Downloading mode)
-Connect your phone to PC via USB cable.
-Wait for the drivers to install. After that, in ODIN, one of the top line "bars" should turn yellow and some text should appear there.
-Download the AriesVE.ops file and check it as OPS. Link to download (attached, scroll down the first post, credits goes to manveru0): http://forum.xda-developers.com/showthread.php?t=1331164
-Then check the 'one package' from the top left
-The ROM you've downloaded, check it as one package. If it's MD5 file. Then click flash.
-Flashing will take about 9 minutes.
-When you see "Close serial port and wait until rebooting" in odin, you can unplug your phone.
-Enjoy!
-If the flashing doesn't complete. Or you face some other problems, just try another USB port, or computer if possible
NOTE: If the ROM includes several files you should check them all. For example XXKP4 2.3.4 Rooted, screen shot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Thanks for guide...finally someone made it.
May i add... if flashing gets stuck somewhere... try another usb-cable and/or usb-port. If possible another computer.
mal13 said:
Thanks for guide...finally someone made it.
May i add... if flashing gets stuck somewhere... try another usb-cable and/or usb-port. If possible another computer.
Click to expand...
Click to collapse
Yes, thanks for reminding.
Thanks.Very useful.
Odin Link doesnt work bro....
Whats their Official Site anyways ? cant find via google
---------- Post added at 10:49 PM ---------- Previous post was at 10:21 PM ----------
Okay got it, I downloaded the I9001ZSKP6 ROM but theres no .OPS file, what to do now ?
Thanks for this mate :0)
Gramrock said:
Odin Link doesnt work bro....
Whats their Official Site anyways ? cant find via google
---------- Post added at 10:49 PM ---------- Previous post was at 10:21 PM ----------
Okay got it, I downloaded the I9001ZSKP6 ROM but theres no .OPS file, what to do now ?
Click to expand...
Click to collapse
I've included the .ops file in the first post. Just open the link and scroll down the first post.
awesome thanks, got the .OPS
Okay man, ur Guide is Great, I'm a beginner and the describtion is very nice, very precise step by step orders.
u got a thanks, and hope u will keep up the helpful work !
Would be good to make this thread sticky!
nikagl said:
Would be good to make this thread sticky!
Click to expand...
Click to collapse
That's why all thanks are appreciated
Thanks!
well im well chuffed, i just flashed to 2.3.6.
is this the same procedure for all roms ?
this version is so much better than my stock 2.3.3, its so much more responsive.
BackDaws said:
well im well chuffed, i just flashed to 2.3.6.
is this the same procedure for all roms ?
this version is so much better than my stock 2.3.3, its so much more responsive.
Click to expand...
Click to collapse
For all stock ROMs yes. CWM for custom ROMs when they start to appear
One noob question. Can I flash this stock ROM from recovery mode, meaning without ODIN. Just to reboot to recovery and than update from zip ?
kabadahija said:
One noob question. Can I flash this stock ROM from recovery mode, meaning without ODIN. Just to reboot to recovery and than update from zip ?
Click to expand...
Click to collapse
What ROM ur talking about ?
Gramrock said:
What ROM ur talking about ?
Click to expand...
Click to collapse
maybe a typical typo these=this . answer to the question. No you cant
Gramrock said:
What ROM ur talking about ?
Click to expand...
Click to collapse
Any of these (yes it is typo), but actually I was thinking about KG3 v2.3.3 ROM ?
Edit: I just see you wrote that i can't flash from recovery.
Do you know why? What is needed to flash from recovery ?
kabadahija said:
Any of these (yes it is typo), but actually I was thinking about KG3 v2.3.3 ROM ?
Edit: I just see you wrote that i can't flash from recovery.
Do you know why? What is needed to flash from recovery ?
Click to expand...
Click to collapse
through cwm Flashable boot.img and correct signing. AFAIK. im not a dev so dont blame me giving incorrect info. Thats for sure you cant flash .smd and .md5 files by cwm
Maybe an idea to remove the actual ROMs mentioned in the first post and refer to the ROM list:
http://forum.xda-developers.com/showthread.php?t=1346245
(btw. some ROM downloads also contain ODIN and AriesVE)
Regards,
Nika.
Finally, after several tests, experiments, and cursing the Rom ANIMUS 1.1.9 and ready
the rom does not want to be the best rom around for our device
ANIMUS was created to give everyone the chance to cook their own rom modding and staff.
the basis of the Rom is 2.3.6 I think the most powerful device for our
Roma is a technically stocks, but lighter, eco additions:
Android 2.3.6 (Gingerbread)
zipalign
Busy box
deodex
enabled bash
app2sd enabled
The ROM is significantly lighter than the basic
installation
1.Download the rom
2.mettere the file to the sd of the device
3.disconnect the device from the PC and turn it off
4.Switch in recovery
5.nel recovery menu to wipe ALL
6.go sd card for installation in the menu and scroll to find the file of the Rom
7.lanciare the installation
8.alla end of the recovery procedure to restart the system
this is the link http://www.megaupload.com/?d=RSVBW3HS
end!
this rom with the kitchen and customizable dsixdia easily ...
tell you guys .. a small step was taken to work. good luck to all the dev!
I do not assume any liability you do so at your own risk
thanks:
scupinatos for availability and kindness
morfes for advice and pazienzaaaaa
qzem ready for answers to any time of night and day
Raidzero for the recovery that has allowed us to get this far
Enjoy
Sorry for my bad English
have you benchmark it?
gymnastiar said:
have you benchmark it?
Click to expand...
Click to collapse
Off course! Personally tested
can u upload the screen shot plizzz . . .
mine got lag when rebooting the phone ...
ut stuck at samsung galaxy wonder while booting
and now got boot looping
Can you upload some screenshot please??..Thank a lot..
Can you reach the Download Mode ?
Hi,
can you still get into the download mode ?
Download-Mode
While switched off, keep pressing the following buttons. Release the Power-Button as soon as the SGW is switched on.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
If possible and you are not able to get this fixed, I can provide you an instruction how to flash a firmware(not the custom firmware) via ODIN.
From which area are you from(country)?
greets
THE-E
THE-E said:
Hi,
can you still get into the download mode ?
Download-Mode
While switched off, keep pressing the following buttons. Release the Power-Button as soon as the SGW is switched on.
If possible and you are not able to get this fixed, I can provide you an instruction how to flash a firmware(not the custom firmware) via ODIN.
From which area are you from(country)?
greets
THE-E
Click to expand...
Click to collapse
i can reach the download mode ..
tell me how then.
jayidoans said:
i can reach the download mode ..
tell me how then.
Click to expand...
Click to collapse
First I need to know from where you are, because there are different firmwares. Or are you anyway going to flash the custom firmware again ?
THE-E said:
First I need to know from where you are, because there are different firmwares. Or are you going to flash anyway the custom firmware again ?
Click to expand...
Click to collapse
i'm from indonesia ..
if possible i want to try this custom ROM .
jayidoans said:
i'm from indonesia ..
if possible i want to try this custom' ROM .
Click to expand...
Click to collapse
THIS IS THE EUROPEAN FIRMWARE, there is also a asian one but I don't have the time to search for it now. But because you are flashing later anyway the custom firmware this shouldn't make a difference.
Instruction
1. Go into the Download mode as instructed on top. As soon as the screen with the exclamation mark appears hit the Volume up-button. Now you should be in the download mode Connect your device to the Computer.
2. Download this file https://rapidshare.com/files/2528654376/Samsung_Galaxy_W_I8150XXKK1__EUR_.rar
and extract all the files.
3. Open Odin Multi Downloader v4.43.exe .
4. click on the OPS-Button and select die Ancora.ops file.
5. Set up the settings as followed:
mark the option: One Package, Protect OPS
unmark the option: Auto Reboot, Reset Time (Sec)
6.Click on the One Package-Button and select the downloaded MD5-file.
7. Click on the Start-Button. Flashing takes around 10-15 minutes. and the first start up takes up to 5 min., so please don't panic.
I DO NOT TAKE ANY RESPONSIBILITY FOR ANY DAMAGE !!! YOUR OWN RISK !!!
Good luck and good night, it is 3:30AM in Germany ^^.
THE-E said:
THIS IS THE EUROPEAN FIRMWARE, there is also a asian one but I don't have the time to search for it now. But because you are flashing later anyway the custom firmware this shouldn't make a difference.
Instruction
1. Go into the Download mode as instructed on top. As soon as the screen with the exclamation mark appears hit the Volume up-button. Now you should be in the download mode Connect your device to the Computer.
2. Download this file https://rapidshare.com/files/2528654376/Samsung_Galaxy_W_I8150XXKK1__EUR_.rar
and extract all the files.
3. Open Odin Multi Downloader v4.43.exe .
4. click on the OPS-Button and select die Ancora.ops file.
5. Set up the settings as followed:
mark the option: One Package, Protect OPS
unmark the option: Auto Reboot, Reset Time (Sec)
6.Click on the One Package-Button and select the downloaded MD5-file.
7. Click on the Start-Button. Flashing takes around 10-15 minutes. and the first start up takes up to 5 min., so please don't panic.
I DO NOT TAKE ANY RESPONSIBILITY FOR ANY DAMAGE !!! YOUR OWN RISK !!!
Good luck and good night, it is 3:30AM in Germany ^^.
Click to expand...
Click to collapse
thanks for your response bro
anyway, is there any download site that's not limiting download speed ?
like mediafire or something ?
any screenshot of this custom rom?
jayidoans said:
mine got lag when rebooting the phone ...
ut stuck at samsung galaxy wonder while booting
and now got boot looping
Click to expand...
Click to collapse
Have you wiped everything before flashing? You should if you haven't.
qzem said:
Have you wiped everything before flashing? You should if you haven't.
Click to expand...
Click to collapse
I had ..
Wipe all + another wipe before doing the update from SD card ..
and the result is Boot Looping.
now i'm trying to flash to stock ROM .
guys I did not put any screenshots just because it's identical to the stock rom
for jayidoans I did it based on this rom Android 2.3.6 European versiione of this device
I do not know if your problem is due to the fact that you have a device with a firmware Asia
but I assure you that Rom and works I tested myself personally.
snake873 said:
for jayidoans I did it based on this rom Android 2.3.6 European versiione of this device
I do not know if your problem is due to the fact that you have a device with a firmware Asia
but I assure you that Rom and works I tested myself personally.
Click to expand...
Click to collapse
i think that there is no difference between euro or asia rom .
but i cant install your custom ROM,
as i said before, it stuck at boot looping
and anyway, for App2SD mods,
should i have a microSD card installed ? and should i format it as ntfs and ext3 ?
how much the quadrant score for this rom?..My stock rom only get 1199.
lvoonjian8888 said:
how much the quadrant score for this rom?..My stock rom only get 1199.
Click to expand...
Click to collapse
You do know that Quadrant scores mean nothing right?
As Chainfire once said: "However, if you put any trust in Quadrant scores you could use them to prove that dancing naked for 5 minutes in your garden affects device performance."
DDLF2 Full (PIT,BOOTLOADER,PDA,PHONE,CSC) Orignal Firmware.
Imported From Samsung Service Center Directly, Ultra Compressed 200 MB Only Uploaded By Me "Sgatechwork". :good: :laugh: :victory: Enjoy ... Don't forget PRESS "THANKS BUTTON" :good: :good:
You Can Directly Flash This On your i9003 no need to flash any thing before this. Because its a full pack firmware.
For cm 10 10.1 or any other based on these if you are from india or if you want your baseband Version to I9003DDLE1 Than just download modem.zip (ultra Compressed) from attachment Extract zip take modem.bin and push it in /radio 0664 which is rw-rw-r--
Like this
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Download Only Modem.bin View attachment modem.zip
Resumable Links
Download Now
Mirror
Mirror Download
Edit:
Confirmation
Installation instructions:
1:Turn Off Your Phone
2ress Vol Down+Home + Power Until Downloading Screen Comes...
3:Than Start Loading Files in
Code:
PIT =latona_20110114.pit
Bootloader =APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5
PDA=CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5
Phone=MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5
CSC=GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5
For CF Root Open Odin 1.85 Load Only PDA=DDLF2-CFROOT-30-06-2012.tar
For Root And ClockWorkMode Recovery
CF Root LF2 (PDA only with Odin) Download Download CF Root Link
Download Odin 1.85 Download Now
Than Check Box Re-Partition Auto Reboot F.Reset Time Phone Bootloader Update Than Press Start When it says PASS In a green Box wait Till reboot is done than remove the cable enjoy...
Does this mean that we can flash DDLF2 directly instead of starting from xxkpe as this new uploaded firmware contain all necessary files??
probably. but still a confirmation would be great.
Sent from my GT-I9003 using xda app-developers app
Yeeh does that mean full clean begin from it .. We need confirm about these thing ..
Thanks very much ..
Sent from my GT-I9003 using xda premium
Tested.Works like a charm.And yes it makes a full wipe.
I suggest you add a guide on how to flash this if its proven that this does not need xxkpe to start with. This is really great. Flashaholic members will no longer have a hard time doing a clean flash.
---------- Post added at 07:47 AM ---------- Previous post was at 07:46 AM ----------
devilhell007 said:
Tested.Works like a charm.And yes it makes a full wipe.
Click to expand...
Click to collapse
You flashed directly? Wow. Have you included the bootloader? your from what base rom?
marshygeek said:
I suggest you add a guide on how to flash this if its proven that this does not need xxkpe to start with. This is really great. Flashaholic members will no longer have a hard time doing a clean flash.
---------- Post added at 07:47 AM ---------- Previous post was at 07:46 AM ----------
You flashed directly? Wow. Have you included the bootloader? your from what base rom?
Click to expand...
Click to collapse
Yeah I flashed it directly.I did not include the bootloader.Iwas on CM 10.1 Alpha 4.Just wanted to make a clean install so tested it.
devilhell007 said:
Yeah I flashed it directly.I did not include the bootloader.Iwas on CM 10.1 Alpha 4.Just wanted to make a clean install so tested it.
Click to expand...
Click to collapse
Great news! :thumbup:
Thanks a lot for the confirmation!
Sent from my GT-I9003.
Good news bro
easy clean now !!!
Tested just now I will review all the installation instructions thank you for this easy clean
With Odin 1.85
- Full LF2 reset odin then remove cable and battery after bootanimation
PIT =latona_20110114.pit
Bootloader =APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5
PDA=CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5
Phone=MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5
CSC=GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5
Click to expand...
Click to collapse
- CF LF2 (PDA only with Odin) reset odin then remove cable and battery after bootanimation
- jellymystery A4 reboot automatic recovery works fine now !!!
- jellymystery A4 again with new recovery
- Wip cache and dalvik cache
time of need to put this topic in post-it
can you add link CFroot LF2 also
- CF Root LF2 (PDA only with Odin)
enjoy...
thanks bro :good:
thanks.
using xwlf2 as a base (eastern europe), but I guess that will do
I never checked "Phone Bootloader Update" in Odin. Is it necessary for this full DDLF2 ?
Currently I'm using same old DDLF2 over XXKPE method without using "Phone Bootloader Update" option
Please confirm.
yes bootloader no need after froyo
just for froyo upgrade (to GB HONEY ISC JB uses the same bootloader) no need updating this !!!
it is even not recommended to put bootloader because it is often responsible for Brick
Bootloader is the first step in flash, if you have a conflict on your computer
avoid process, samsung kies, adb, antivirus internet security software and others scan stuff before flash !!!
@LoLaTiOn!
That what i thought so and read everywhere but was bit confused about checking that option. Thanks! for confirming
I would like to go back to GB from Jb only because of the battery.
Im currently in Qwerty
can someone post every single step in a noob (me) friendly way,please?
From what i've read:
1) you need odin 1.85 installed on your pc
2)Start the phone while pressing Vol down+home+power to start in download mode (these has to be with the phone connected to the pc via usb cable or you can plug it in later?)
3)Fill every file category with the corresponding file in odin.
4)Check Box Re-Partition Auto Reboot F.Reset Time Phone Bootloader Update
5)Press Start
7)When it says PASS In a green Box wait Till reboot is done ....
8)thee remove usb cable from phone
Am i missing something? devilhell007 says that you dont need the bootloader file? Is this file necessary only with certains roms? which roms would that be?
and finally, i've read that some roms, change the file system of the phone, and returning to stock bricks it, does this method prevents and reverts that?
sorry for the noobish questions, big thanks in advance!
Load all the files as i mentioned... and flash it... than after paas ur done...
Sent from my GT-I9003 using xda premium
felaipes said:
I would like to go back to GB from Jb only because of the battery.
Im currently in Qwerty
can someone post every single step in a noob (me) friendly way,please?
From what i've read:
1) you need odin 1.85 installed on your pc
2)Start the phone while pressing Vol down+home+power to start in download mode (these has to be with the phone connected to the pc via usb cable or you can plug it in later?)
3)Fill every file category with the corresponding file in odin.
4)Check Box Re-Partition Auto Reboot F.Reset Time Phone Bootloader Update
5)Press Start
7)When it says PASS In a green Box wait Till reboot is done ....
8)thee remove usb cable from phone
Am i missing something? devilhell007 says that you dont need the bootloader file? Is this file necessary only with certains roms? which roms would that be?
and finally, i've read that some roms, change the file system of the phone, and returning to stock bricks it, does this method prevents and reverts that?
sorry for the noobish questions, big thanks in advance!
Click to expand...
Click to collapse
LoLaTiOn said:
yes bootloader no need after froyo
just for froyo upgrade (to GB HONEY ISC JB uses the same bootloader) no need updating this !!!
it is even not recommended to put bootloader because it is often responsible for Brick
Bootloader is the first step in flash, if you have a conflict on your computer
avoid process, samsung kies, adb, antivirus internet security software and others scan stuff before flash !!!
Click to expand...
Click to collapse
As you can see LoLaTiOn said the same thing.
And bootloader might even brick your phone.So please refrain from doing so.
I hav no idea about it in samsung service center offically.. they use all the files to flash including bootloader even me my self always flashed my phone with all files never bricked... infact with my previous phone i always used bootloader and all files... els u c
Sent from my GT-I9003 using xda premium
the first galaxysl and comes with froyo
That is why we must put the bootloader for an upgrade to gingerbread
after the upgrading not a time of need for clean
understand all ?
if a person is on froyo and does not put the bootloader it will encounter a bootloop only ^^
i totally understand and agreed with you
LoLaTiOn said:
the first galaxysl and comes with froyo
That is why we must put the bootloader for an upgrade to gingerbread
after the upgrading not a time of need for clean
understand all ?
if a person is on froyo and does not put the bootloader it will encounter a bootloop only ^^
Click to expand...
Click to collapse
i totally understand and agreed with you but i am just saying what Samsung engineers thought to there service center technicians and instructed to do as per proper procedure, load all the files and flash it they do this for all the device any Samsung phone down grade up grade or same reflash they do the same sorry if am wrong but am just saying in the official way rest all on us...
Having had a long research after I bricked my lenovo p12 pro 12.6(the CN version) ,I thought I finally figured out what is happening when boot ROW firmware on my tablet and a method to bypass such region check. Here is detail procedure:
First of all ,you DO NOT need to return your bricked tablet back to the seller or manufactures, any of which costs time and patience.
1、Download the super partition image file Mod edit: Links removed ,and extract super.img from it using 7z x ... command.
2、You can choose to use my bash shell script (flash_stock_firmware.sh)or your manual instructions: to flash the stock firmware
Bash:
bash 'flash_stock_firmware.sh' 'PATH/TO/THE/STOCK/FIRMWARE/FOLDER'
,it takes about 5 minutes to end.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
After it booted to framework ,the init process will play a bootanimation ,in my case it shows :
This is exactly what we should to remove.And now you could reboot the tablet into fastboot mode
Code:
fastboot flash super PATH/TO/EXTRACTED/SUPER/IMAGE
fastboot erase userdata
fastboot erase metadata
fastboot reboot
In my case ,my tablet successfully launches the SetupWizard for registering device to google:
Wow fantastic work? Any chance you can elaborate anymore in your instructions for the more novice users? I've not used ADB before. When I tried and the tablet was broke ADB couldn't see the tablet where as QFIL could.
Does the boot loader have to be unlocked?
I'm still waiting for mine back from china but depending on the stability of the Global ROM I may move across.
Is the above doable only with ADB or can it also be done in QFIL?
Does the Global ROM successfully OTA for you or does it fail after download? Can you search from the settings menu?
Going forward are you able to use the Lenovo Recovery Centre to flash updates Global ROM's without having to do the steps above again?
mardon85 said:
Wow fantastic work? Any chance you can elaborate anymore in your instructions for the more novice users? I've not used ADB before. When I tried and the tablet was broke ADB couldn't see the tablet where as QFIL could.
Does the boot loader have to be unlocked?
I'm still waiting for mine back from china but depending on the stability of the Global ROM I may move across.
Is the above doable only with ADB or can it also be done in QFIL?
Does the Global ROM successfully OTA for you or does it fail after download? Can you search from the settings menu?
Going forward are you able to use the Lenovo Recovery Centre to flash updates Global ROM's without having to do the steps above again?
Click to expand...
Click to collapse
Edited
ZTE AXON 7 said:
otloader
2、fastboot boot rec/recovery.img(Here you should wait for about thirty seconds before initialization completed)
3、adb push systemrw_1.32_flashable.zip /sdcard
4、Go to Install->/sdcard/ and choo
Click to expand...
Click to collapse
ZTE AXON 7 said:
Edited
Click to expand...
Click to collapse
Thanks for this. Its the info I think a lot of us have been waiting for.
Did you find the following issues with your global ROM the same as the video below @ 27:14
That is some really good news, great work!
Thanks for sharing your work. However, could you kindly make the link available without requesting permission asking to share our gmail address with you?
Thanks!
ZTE AXON 7 said:
h costs time and patience.
1、Download the super partition image file Mod edit: Link removed ,and extract super.img from it using 7z x ... command.
Click to expand...
Click to collapse
famaTV said:
Thanks for sharing your work. However, could you kindly make the link available without requesting permission asking to share our gmail address with you?
Click to expand...
Click to collapse
Download link was updated
Thanks for updating download links.
Once these changes have been updated can we simply download and flash newer ROW ROM's?
How is your device performing, any glitches?
ZTE AXON 7 said:
Download link was updated
Click to expand...
Click to collapse
Thanks … but even the other website requests mobile number or email address to download.
Too much work and privacy exposure to take. I would wait for someone else to re-upload the file to a more straight forward user friendly site.
Meanwhile, what have you changed to the super.img to make it bypass the region check? Do you have the CN full firmware file?
On the other hand, with your fix, will the tablet update firmware OTA without any issues?
Thanks again.
ZTE AXON 7 said:
EXTRAC
Click to expand...
Click to collapse
mardon85 said:
Thanks for updating download links.
Once these changes have been updated can we simply download and flash newer ROW ROM's?
How is your device performing, any glitches?
Click to expand...
Click to collapse
So far so good, all works fine ,120hz refresh rate,precision 3 pencil ,precisicion keyboard,fast charging,etc...
There is a brand new ROM out today. Are you able to flash that now? Have you tried changing the region code via a hex editor?
lolinet mirrors - firmware, software, iso etc.
lolinet mirrors - powered by h5ai
mirrors.lolinet.com
famaTV said:
Thanks … but even the other website requests mobile number or email address to download.
Too much work and privacy exposure to take. I would wait for someone else to re-upload the file to a more straight forward user friendly site.
Meanwhile, what have you changed to the super.img to make it bypass the region check? Do you have the CN full firmware file?
On the other hand, with your fix, will the tablet update firmware OTA without any issues?
Thanks again.
Click to expand...
Click to collapse
I updated to S212017 with this super image ,no problem:
ZTE AXON 7 said:
I updated to S212017 with this super image ,no problem:
View attachment 5506983
Click to expand...
Click to collapse
Is that via QFIL or OTA and also can you check if the search box works within the settings menu.
mardon85 said:
Is that via QFIL or OTA and also can you check if the search box works within the settings menu.
Click to expand...
Click to collapse
OTA,I changed the original ota update logic from aosp.
ZTE AXON 7 said:
OTA,I changed the original ota update logic from aosp.
Click to expand...
Click to collapse
Wow it seems you've cracked it even better than the Ali Express sellers. Most of the reports are that it can't OTA and the issue with the Settings search bar.
If mine ever clears Chinese customs (been stick there for 12days now) I'll get mine back and be able to play.
Ok I'm looking at your instructions.
The flashing of the stock firmware is the easy bit.
Once you do that you get the not compatible message as per your original instructions.
At this point the tablet is stuck in a screen similar to below. It does not matter which option you chose the tablet will reset back to the same screen.
What exactly do you do from this point to flash these instructions and your Super Image.
fastboot flash super PATH/TO/EXTRACTED/SUPER/IMAGE
fastboot erase userdata
fastboot erase metadata
fastboot reboot
If I try and run abd I get the following:
Sorry these are probably a no brainer with your capabilities but this is all quite new to me.
Basically I can see the tablet when Android is up and running but not from fastboot mode?
mardon85 said:
Ok I'm looking at your instructions.
The flashing of the stock firmware is the easy bit.
Once you do that you get the not compatible message as per your original instructions.
At this point the tablet is stuck in a screen similar to below. It does not matter which option you chose the tablet will reset back to the same screen.
View attachment 5507019
What exactly do you do from this point to flash these instructions and your Super Image.
fastboot flash super PATH/TO/EXTRACTED/SUPER/IMAGE
fastboot erase userdata
fastboot erase metadata
fastboot reboot
If I try and run abd I get the following:
View attachment 5507027
Sorry these are probably a no brainer with your capabilities but this is all quite new to me.
Basically I can see the tablet when Android is up and running but not from fastboot mode?
Click to expand...
Click to collapse
UPDATE... Fast boot commands do actually work. Even though it wont list devices commands like reboot work fine.
Did you have to unlock your bootloader for this? Have you kept widevine L1?
@ZTE AXON 7 you seem to be using Linux like me, mostly. I've used QFIL to flash the ROW ROMs but never did it from Linux. Do you have instructions on how to do that?
Oh wait, I reread your post. That script is for flashing the stock ROM, just like you said. Sorry about that.
Thank you for your work
I don't understand this very well. Do you have detailed operation steps?