today i received Brand new j700H/DS 5 pcs for language
after flashing with odin all of them are dead no power at all
not going to download mode and nothing appears in computer when i connect it with computer
the flash file i use its working and tested file
always i use same file never had such a problem
after these phones i flash other phone on same flash file just to test if files has problem or no but it was working fine
even not matter of downgrading because i flash a phone with a latest version the last version which was available in samemobile.com then i tried to downgrade its working fine so phones are not dead because of downgrading
my question how to check if the bootloader is damage and which box has support for j700H boot repair
please replay i need a quick solution
thanks
j700f/DD (make in india.Christmas Pack) Dead After Flash off is if I start guide
Have you found a solution?
Also have a dead J700H/DS
I flashed with J700H file though
---------- Post added at 06:40 AM ---------- Previous post was at 06:40 AM ----------
Have you found a solution?
Also have a dead J700H/DS
I flashed with J700H file though
j700f/dd dead
Hi.
I have a samsung j700f / DD dead after pass flash with odin
Computer does not recognize my mobile.
(How can I get your phone to connect my computer? When the computer does not recognize it?)
1. Is there any way that the computer can recognize my mobile?
2. Is the problem can be solved by software?
ⴰⵣⵓⵍ,
Take the battery off then put it on after each of the attempts below...
Well before doing anything else, try a combination of keys such as :
- Power button + Home Key + Vol Up
- Power button + Home Key + Vol Down
- Power button + Vol Up
- Power button + Vol Down
- Etc
If nothing appears, then try a combination of keys while plugging it at the same time to the PC, but before doing so check if anything got detected [ sudo tail -f /var/log/messages ] :
- Vol Down
- Vol Up
- Vol Up + Vol Down
- Home Key
- Home key + Vol Up
- Home key + Vol Down
Note : In some SoC's the preloader or the SoC bootloader sometimes pops up for a few seconds and disappears, which gives the time for the flash tool to establish a connection before the SoC bootloader closes the connection, in other cases it keeps popping in and out, so focus when plugging the cable.
Then report back to this thread.
CHAOS-THEORY said:
ⴰⵣⵓⵍ,
Take the battery off then put it on after each of the attempts below...
Well before doing anything else, try a combination of keys such as :
- Power button + Home Key + Vol Up
- Power button + Home Key + Vol Down
- Power button + Vol Up
- Power button + Vol Down
- Etc
If nothing appears, then try a combination of keys while plugging it at the same time to the PC, but before doing so check if anything got detected [ sudo tail -f /var/log/messages ] :
- Vol Down
- Vol Up
- Vol Up + Vol Down
- Home Key
- Home key + Vol Up
- Home key + Vol Down
Note : In some SoC's the preloader or the SoC bootloader sometimes pops up for a few seconds and disappears, which gives the time for the flash tool to establish a connection before the SoC bootloader closes the connection, in other cases it keeps popping in and out, so focus when plugging the cable.
Then report back to this thread.
Click to expand...
Click to collapse
==================================================================================================
Hi
I did the steps. But in any case, the computer did not recognize the phone.
Then
I repeated the process with the power supply, too.
The result was that:
1. When the power button is pressed. (amount of flow is equal to 0.12.)
2. Whenever USB cable to connect the phone. (amount of flow is equal to 0.12.)
3. In all other cases (amount of flow is equal to zero)
where is the problem from? Is there a way to enter into download mode
When no images (dead), and amount of flow is not suitable for phones.
I am also using USB jig, steps did. But did not alter.
I am waiting your reply friends.
Thanks.
ⴰⵣⵓⵍ,
I have mentioned that you need to take the battery off everytime you make an attempt, did you do that?
And what flow are you talking about, electrons? charges? current? what's that amperes?
I don't understand what you mean by power supply, i can't follow you, and what about the jig, i've read that samsung's uses a system to enable different modes depending on the amount of resistance between DP and DM of the usb, i really don't know about this, but give it a try.
Technically if you corrupted the SoC internal bootloader, the phone wont be able to perform anything, unless mainly using JTAG to reflash the internal flash memory region of the SoC [ system on chip ], am actually stuck at the same place with an MSM8625 SoC from Qualcomm, i couldn't find anything else to communicate with the SoC's main ARM chip except the JTAG pins, logically there isn't another way in here.
j200h dead after flash
CHAOS-THEORY said:
ⴰⵣⵓⵍ,
Take the battery off then put it on after each of the attempts below...
Well before doing anything else, try a combination of keys such as :
- Power button + Home Key + Vol Up
- Power button + Home Key + Vol Down
- Power button + Vol Up
- Power button + Vol Down
- Etc
If nothing appears, then try a combination of keys while plugging it at the same time to the PC, but before doing so check if anything got detected [ sudo tail -f /var/log/messages ] :
- Vol Down
- Vol Up
- Vol Up + Vol Down
- Home Key
- Home key + Vol Up
- Home key + Vol Down
Note : In some SoC's the preloader or the SoC bootloader sometimes pops up for a few seconds and disappears, which gives the time for the flash tool to establish a connection before the SoC bootloader closes the connection, in other cases it keeps popping in and out, so focus when plugging the cable.
Then report back to this thread.
Click to expand...
Click to collapse
hello sir my set is dead after flash then i did above method phone is detected when i pressed volume up + power button and connected to pc......... now how to repair it.........
Related
I have seen this asked quite a bit around here lately. Thought I would put this out there for reference. Let me know if you have better ways/I have it totally wrong.
FIRST METHOD (easiest/most common)
1) Power phone off
2) Plug USB into computer
3) Hold vol up + vol down
4) Plug USB into phone while still holding the vol up and vol down
5) Yellow /_\ (triangle, Downloading, Andy shoveling, Do not turn off Target!!! symbol)
Your now in Download mode
SECOND METHOD
1) Power phone off
2) Plug USB into Computer
3) Plug microUSB into phone
4) Hold pwr + vol up + vol down
5) When Batt icon goes away, release pwr, still holding vol up + vol down
6) Yellow /_\ (triangle, Downloading, Andy shoveling, Do not turn off Target!!! symbol)
You should now be in Download mode.
THIRD METHOD
1) Power phone off
2) Pull battery out
3) Hold vol up + vol down
4) While holding vol up + vol down, plug in USB cable into the phone
5) While still holding vol up + vol down, put battery back in
6) Yellow /_\ (triangle, Downloading, Andy shoveling, Do not turn off Target!!! symbol)
You should now be in Download mode.
FOURTH METHOD (adb)
1) Enable debugging on your phone (Menu>Settings>Applications>Development>)
2) With phone on, plug USB into computer and phone
3) Open cmd
4) Type in "adb devices" (not totally necessary, but I always do it just to make sure everything is good), making sure it recognizes your device
5) Type in "adb reboot download"
6) Yellow /_\ (triangle, Downloading, Andy shoveling, Do not turn off Target!!! symbol)
You should now be in Download mode.
If you have CERTAIN GB bootloaders it changes the the way you access download and recovery.
Download mode = vol down + pwr (NOT - vol up + vol down + pwr)
Recovery = vol up + pwr (NOT - vol up + vol down + pwr)
Like I said, let me know if any of this should be changed.
*Edit- Changed steps 4 & 5 in "THIRD METHOD", per comments.
Perfect
the first method worked for me
For the 3rd method I plug in the usb cable first, then push both volume keys, then put battery back in while holding both volume keys.
Great guide, thanks!
ive got a bricked phone that doesnt even respond to the USB jig... and still none of these work for my "phone--!--comp" screen
Does odin recognize it? In most cases you can still flash odin on that screen.
not sure if you got yours fixed. If you can see your phone + !+ comp then it's not a full brick. Jig should work, it worked for me today.
I got this, what do I do next? I keep getting message "SIM network unlock PIN". I have tried everything I find in this site, only to be dazed...I have two SamsungS Vibrant's and I got one to work just fine...it's the second that has gotten the better of me...HELP, please and THANK YOU
4th method should be
open cmd then
cd/
cd androidsdk
cd tools
adb devices (to make sure its connected)
adb reboot download
jdubb1106 said:
4th method should be
open cmd then
cd/
cd androidsdk
cd tools
adb devices (to make sure its connected)
adb reboot download
Click to expand...
Click to collapse
I have mine pointed a tools.
Great guide, thanks!
try this, hold the volume down button and power then insert the USB. worked for me. haha
I tried all these methods after updating to 2.3.4 and can not get back into the download mode. Any suggestions please? Thanks in advance.
Hold volume down + up and insert usb while phone is off
I did that. It didn't work.
EDIT:
I evidently did it wrong. It worked the last time I tried. Thanks
i'm on 2.3.3 and am having this issue with not being able to get back into download mode anymore or recovery mode. tried every combination and all four mentioned in another thread. is there another way to flash a rom without being in download mode? can i just do it straight from odin after plugging it in?
mine didnt seem to work with any of those but i saw a video based on the epic by holding down the #"1" button on the key pad and the power button takes you to download mode ,and it worked for me
It Works
Volume down + Power..It works Thanks!!
But am still stuck with bad IMEI ..
omg!
thank you so much! it worked for me. but my imei is still null . and wont read my sim card. any of them this happened after i tried to unlock it . does any one know how to fix it? ive used odin and flashed the stock rom still didnt work. ive upraded it to 2.3.3 still didnt work. idk what the deal is . but it wont work. can any one help me with this? i have a galaxy s 4g for tmobile. it keeps saying searching at the top
What I do, is take the battery out, put the battery in, plug in the usb, take the battery out, volume up down up down up down up down, unplug usb, take out the battery, take the dog for a walk, put the battery back in, hold down the volume keys, then plug it in, and it works!
jk, great guide. much thanks
Hello all. Just dont know what i must do.
Situation:
I was trying flash phone by Flashtool for update. I plug/unplug usb + pressed volume high btn and Flashtool not found it (problems with drivers). And on some time i unplug usb and try ON mobile and it no show indication/display off and etc. So i press Pwr + Vol Btn + and it started... Im try second (Not found device too) and repeat press Pwr + Vol Btn + and it not on. No Led indication, when try plg usb after 10-15 seconds windows find device but it Unknown! ( Red traingle in devices /!\ ). Flash process not was started(i think phone lived). I plug in on wall charger and want ask. It soft brick or hard? And what i can do?
Device:
Unlocked boot
Rooted
Flash on stock frimware after custom rom.
GarikIzzy said:
Hello all. Just dont know what i must do.
Situation:
I was trying flash phone by Flashtool for update. I plug/unplug usb + pressed volume high btn and Flashtool not found it (problems with drivers). And on some time i unplug usb and try ON mobile and it no show indication/display off and etc. So i press Pwr + Vol Btn + and it started... Im try second (Not found device too) and repeat press Pwr + Vol Btn + and it not on. No Led indication, when try plg usb after 10-15 seconds windows find device but it Unknown! ( Red traingle in devices /!\ ). Flash process not was started(i think phone lived). I plug in on wall charger and want ask. It soft brick or hard? And what i can do?
Device:
Unlocked boot
Rooted
Flash on stock frimware after custom rom.
Click to expand...
Click to collapse
Solved. Phone was Soft-Bricked and problem: Low Battery level.
Hi,
Recently i was trying to apply another rom to my Samsung Galaxy A7 2018 edition and i am stuck in an infinite bootloop. I cannot enter download mode with the Volume Down and Power keys and the only thing it does is showing the logo of Samsung every 5 seconds and restarts. I have tried to built a usb jig with 300k resistors and still does not boot up in download mode to flash with odin a stock firmware. Also i left the battery to drain and now it is turned off,but when i plug in the usb cable and power it up it still goes into infinite loop. Any help?
I was trying the Android 10 Magisk root for A750F and was greeted by a similar situation after ODIN rebooted my phone after flashing Magisk image.. Anyways, don't panic, try all combination of buttons. vUP,vDN,PWR or vUP,PWR or vUP,vDWN while connected to usb.. It wasn't working for me too but i tried all combinations and it landed me to download mode where I flashed the stock rom
just press those button and connect to usb
im glad i read his, had just the same issue while flashing wrong twrp on A750FN .. yihey thx budies
how did you solve this issue.
---------- Post added at 06:54 AM ---------- Previous post was at 06:45 AM ----------
which button combination helped you. I having a similar issue. can not enter download mode.
Solution that helped me
Just Press the volume plus + volume minus + power button at once. Once the phone reboot black screen appears, Leave the power button and keep pressing the volume plus and volume minus button. It will redirect to the download mode. and reflash the room using Odin. Only use official sammobile rom file as other files may be corrupted. The issue may arise. The problem is in rom.
If any issue query me at : [email protected].
try this bro
Tantalord said:
Hi,
Recently i was trying to apply another rom to my Samsung Galaxy A7 2018 edition and i am stuck in an infinite bootloop. I cannot enter download mode with the Volume Down and Power keys and the only thing it does is showing the logo of Samsung every 5 seconds and restarts. I have tried to built a usb jig with 300k resistors and still does not boot up in download mode to flash with odin a stock firmware. Also i left the battery to drain and now it is turned off,but when i plug in the usb cable and power it up it still goes into infinite loop. Any help?
Click to expand...
Click to collapse
do one thing hold volume + and volume - buttons toggether and connect your phone to pc while holding v+ and v- buttons your phone redirect to download mode without any other logo/animation :good:
zebby12 said:
I was trying the Android 10 Magisk root for A750F and was greeted by a similar situation after ODIN rebooted my phone after flashing Magisk image.. Anyways, don't panic, try all combination of buttons. vUP,vDN,PWR or vUP,PWR or vUP,vDWN while connected to usb.. It wasn't working for me too but i tried all combinations and it landed me to download mode where I flashed the stock rom
Click to expand...
Click to collapse
icodix said:
just press those button and connect to usb
Click to expand...
Click to collapse
ikram.senguen said:
im glad i read his, had just the same issue while flashing wrong twrp on A750FN .. yihey thx budies
Click to expand...
Click to collapse
simonastani21 said:
Solution that helped me
Just Press the volume plus + volume minus + power button at once. Once the phone reboot black screen appears, Leave the power button and keep pressing the volume plus and volume minus button. It will redirect to the download mode. and reflash the room using Odin. Only use official sammobile rom file as other files may be corrupted. The issue may arise. The problem is in rom.
If any issue query me at : [email protected].
Click to expand...
Click to collapse
I have tried keeping all 3 buttons (vol up + vol down + power), tried holding vol up + vol down and then connecting to my PC (nothing happens, I always see the same screen (SAMSUNG Galaxy A7 Secured by Knox and Powered by android underneath)).
Tried vUP,vDN,PWR or vUP,PWR or vUP,vDWN while connected to PC via USB.
Tried vUP,vDN,PWR or vUP,PWR or vUP,vDWN while NOT connected to PC via USB.
Phone sometimes reboots but always gets into the screen I mentioned above.
Odin, obviously, doesn't see the phone either.
Also, adb devices command deosn't show the device in the list.
Anything else I should try?
Ah I solved it, and nobody mentions that you have to be SUPER quick!?
So you hold down vol down + power button and keep the USB cable at hand and the millisecond your phone reboots, reeeealy quickly release vol down and power and quickly afterwards press vol down + vol up and again quickly plug in your USB cable, if you did it before the Samsung logo appears you will get into Downloading... screen.
androidBanana said:
Ah I solved it, and nobody mentions that you have to be SUPER quick!?
So you hold down vol down + power button and keep the USB cable at hand and the millisecond your phone reboots, reeeealy quickly release vol down and power and quickly afterwards press vol down + vol up and again quickly plug in your USB cable, if you did it before the Samsung logo appears you will get into Downloading... screen.
Click to expand...
Click to collapse
haha nice. we have different procedures though.
simonastani21 said:
Solution that helped me
Just Press the volume plus + volume minus + power button at once. Once the phone reboot black screen appears, Leave the power button and keep pressing the volume plus and volume minus button. It will redirect to the download mode. and reflash the room using Odin. Only use official sammobile rom file as other files may be corrupted. The issue may arise. The problem is in rom.
If any issue query me at : [email protected].
Click to expand...
Click to collapse
doesn't work for me
Tantalord said:
Hi,
Recently i was trying to apply another rom to my Samsung Galaxy A7 2018 edition and i am stuck in an infinite bootloop. I cannot enter download mode with the Volume Down and Power keys and the only thing it does is showing the logo of Samsung every 5 seconds and restarts. I have tried to built a usb jig with 300k resistors and still does not boot up in download mode to flash with odin a stock firmware. Also i left the battery to drain and now it is turned off,but when i plug in the usb cable and power it up it still goes into infinite loop. Any help?
Click to expand...
Click to collapse
just plug it to ur pc while pressing vol up + down, works for me
sagar81307 said:
try this bro
do one thing hold volume + and volume - buttons toggether and connect your phone to pc while holding v+ and v- buttons your phone redirect to download mode without any other logo/animation :good:
Click to expand...
Click to collapse
Hello sir, I just want to thankyou alot this fixed my problem. I tried to install a android 13 gsi rom that I saw was compatible with my phone but the after I installed it had some bugs and I restarted my phone to go to download mode and flash a backup I had but the phone went into a bootloop with in to the recovery(i was using pbrp) and I couldnt get into download mode even to flash my stock rom. after I saw you post I tried it and it took me in to a screen that was saying you system has been corrupted and asked me if I wanted to go to download mode and said yes and flashed my rom and everything is working now
Thank you Again
so I just tried to install unofficial TWRP 3.5.0 on my Samsung galaxy a125m and everything went fine, Odin said done. Then I just tried to start TWRP by pressing power and vol up and it didn't start, so I thought I might have done something wrong and rebooted to download mode and flashed it again, Odin said done, then I unplugged the USB cable and now it won't boot, neither to the system or recovery, even to download mode, it did enter download mode a few times before but I pressed the wrong button and had to cancel and enter again, now it won't even enter download mode so I can't flash stock rom to fix bootloop... pls how can I solve this I'm desperate
when I try to enter download mode by pressing volume up + volume down it just shows up charging mode without any numbers, then it turn on and shows Samsung logo, unlocked bootloader warning screen, and the Samsung logo again, but then just restarts and repeats all again...
when I try to press volume up + volume down + power, nothing really happens...
someone help me please
You need to keep both volume up and down pressed, then plug in the charging cable. It should enter download mode, no need to press the power button like in older samsungs.
PhotonIce said:
You need to keep both volume up and down pressed, then plug in the charging cable. It should enter download mode, no need to press the power button like in older samsungs.
Click to expand...
Click to collapse
yeah I did that a lot of times, it used to work now It doesn't anymore
in this video you can see what's going on, I'm pressing both volume keys and nothing happens
Your browser is not able to display this video.
Is the cable plugged into a charger and on?
Have you considered that your volume buttons may not be working?
Same hear
Try attaching your phone to the PC, and then pressing volume down + power to reset the phone, (for about 7~8 seconds) then immediately press the volume down and up buttons, that's how I recovered from it. Tell me if it worked
juliano-oh! said:
Try attaching your phone to the PC, and then pressing volume down + power to reset the phone, (for about 7~8 seconds) then immediately press the volume down and up buttons, that's how I recovered from it. Tell me if it worked
Click to expand...
Click to collapse
Please help it dosent worked
No pc detection
No download mode
No recovery
No charging
Hello, unfortunately in these cases the only solution is to enter download mode, check if any button is damaged or if the cable works and if it is well connected, press the buttons harder, hold down the volume up and volume down buttons at the same time , by pressing the strong buttons, for about 6 seconds and then connect the cable. If you don't try another cable to see if that's the problem there is no other solution as the phone is not recognized by an app that can put it into download mode when turned off the solution is the one I already told you about. I hope you have fixed that problem. Sorry for my bad English.
developeMYWORLD said:
Please help it dosent worked
No pc detection
No download mode
No recovery
No charging
Click to expand...
Click to collapse
To Escape the Black Screen of Death or Bootloop
To boot to RECOVERY MODE
Method 1
First connect phone to the PC for 30 minutes
Hold all 3 keys and release volume down when it buzzes.
Method 2
1. Plug in USB cable to PC
2. Hold down all 3 buttons on phone.
3. When it buzzes release volume down and plug in USB cable to phone.
Then restore your backup or install a ROM
To boot to DOWNLOAD MODE
Method 1
First connect phone to the PC for 30 minutes
Hold all 3 keys and release power when it buzzes.
Method 2
1. Plug in USB cable to PC
2. Hold down all 3 buttons on phone.
3. When it buzzes release power button and plug in USB cable to phone.
Then use Odin to flash official firmware.
@physwizz
I am having a similar problem with the Samsung A12 SM-a125u
I never could enter into this "Downloading mode".
I tried flashing the stock ROM through ADB with fastboot, and I have another problem that I've never seen before: ADB can see the device while in recovery mode, but fastboot can't. And so it won't allow me to flash the ROM and I don't even know how Odin is supposed to help yet; I think I needed to enter Downloading mode for that, but I can't get into it.
I'm working on this phone for a friend who was given it because his friend's mom doesn't remember the password to it. Does that matter? It's worth noting that because of that I cannot get in to turn on OEM unlocking or dev mode, but idk why that would come into play in recovery mode. Also, the model indicates this is an AT&T phone, and tutorials online have acknowledged this model in their "applicable models" list at the beginning of their tutorials, but I know that carrier phones can cause problems all over the place (stop buying carrier locked phones people!); is this a problem?
How the heck do I flash the stock ROM to this this?
Hey Guys,
I need help with Nokia G10 TA-1334. After the loading screen the display becomes black. Only thing I can do is holding the power key and the menu appears with lock, switch off and restart. Tried to reach the recovery mode but no key combination would bring it. The only menu I can reach is the fastboot menu, but the debugging mode is not switched on so the adb commands are not available. Can you please tell me a working key combination for the recovery mode. I also tried flashing it with sp flash but again it is not working. I tried again different key combinations. The phone is connecting to the pc normally but without the screen I can't do anything.
So Far I Tried these:
With plugged in cable:
Holding Power + Volume up is only restarting the phone
Holding Power + Volume down - fastboot ( but there is not any additional menu)
Holding Power + Volume down and when android logo comes holding only power and fast press volume up
Holding Power + Volume up and down = nothing
Hi Ivan, my G10 has had exactly the same problem as yours since Friday. Have tried the same things as you and also had no success. I tried draining the battery to flat but that didn't work either. Have you had any luck finding a solution? Thanks, Tony
For now nothing, the draining wont work probably because I disassembled the phone and disconnected the battery. After that no change has occured. I hope that somebody will provide a working key combination for the recovery mode.
hello, nokia g10 and the same problem, did you find a solution?
Hi guys.
Did you find a solution to this problem?
Same Problem, we can reboot to Android Bot with NO COMMAND prompt, but hard to enter recovery menu with the combined power key & Vol+ key.
Is there someone know the new version how to enter recovery menu? Tks.