hi so my samsung galaxy s4 GTi9505 internatinal version got hard bricked will the jig usb force it into download mode and from there i open odin then flash the officail rom
Hi,
Please check this thread to unbrick your device: http://forum.xda-developers.com/showthread.php?t=2265477
A jig is used to boot into download mode but flashing a stock firmware with a .pit file will re-partition and return your device to stock.
Thank you for using XDA Assist,
Good luck.
Related
Hi,
I attempted to load a custom ROM on a Samsung Galaxy S 5 G900P. I can get to download mode and recovery mode. I loaded a new ROM through the recovery mode but when I boot it gets to the Samsung Galaxy S 5 screen and stays there.
I have downloaded the stock firmware to try and flash back to stock but when I try to flash the stock firmware through ODIN, the flash Fails.
Any guidance to try?
Thanks
Hi, thank you for using xDA Assist. Make sure you're using the same version of the firmware your device was on. Also use the USB ports in the back of the PC and try different usb cables. Odin can be finicky. If you need further help you can ask in your device's specific forum here, http://forum.xda-developers.com/sprint-galaxy-s5
Thread closed.
I have the Verizon Galaxy s4 and I rooted it and attempted to install the cm-12.1 custom rom. I could not get CWM to work so I went to the safestrap route. My phone got stuck booting into recovery so I flashed stock everything VIA Odin. It failed. So now I'm stuck with the message at start up "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again".
Please HELP.
P.S It is the SCH-I545 model.
Hi,
Thanks for using XDA Assist Looks like you fixed issue has per your post here
Thread Closed.
I flash a stock rom for my Star2Plus and the usb cable was removed before the end of the process, so it has been bricked it's stock at samsung logo and when I try to flash a stock rom again it contunie until System then stop with a red fail botton but when I flash CWM it flashes ok so please help :crying::crying:
yazanee said:
I flash a stock rom for my Star2Plus and the usb cable was removed before the end of the process, so it has been bricked it's stock at samsung logo and when I try to flash a stock rom again it contunie until System then stop with a red fail botton but when I flash CWM it flashes ok so please help :crying::crying:
Click to expand...
Click to collapse
Hi and thank you for using XDA Assist
Unfortunally i couldn't find the device forum for your mentioned one so the better way to ask is to do it here >>> Android Q&A, Help & Troubleshooting
Good luck!
I'm playing my p6800 normally then it turn off when open again it stunk at samsung logo (Samsung Galaxy Tab7.7) and can't charging. I think battery was degenerate. I have replaced a new one it doesn't work(still stunk at samsung logo)
At the first time I can access Download mode and Stock recovery mode but it can't flash official rom via odin 3.10
I tried to read many post in XDA and tried to flash PIT,other ROM,kernel and CWM it is mostly stuck at NAND Write Start!!! and FAIL
(I read and get PIT file in http://forum.xda-developers.com/showthread.php?t=1667886 )
NOW I can't go to recovery mode but can access Download mode
Please suggest best way or method to revive my p6800
Device : P6800
ROM : Official 4.1.2
Odin : 3.10 and not kies installed
Windows 7
P.S. Sorry, I'm not good at English
Only way to revive this is to get a new tab
Hi
I tried to flash stock firmware via odin by mistakenly selected NAND erase option and odin failed
After that it's not booting to download mode (odin mode).
Can someone help me to unbrick my phone.