Database Info

Hardbricked - System destroyed!

Hello!
I was disappointed about some missing features in MIUI ( unable to unlock by bluetooth by not Xiaomi devices, no reliable notification LED,.. ) so I decided to flash Android P ( I know, it´s beta, but it´s AOSP ) by using the Xiaomi Flash Tool. I left the button at 'clean and lock', because I don´t wanted to go back in the near future - and this was a big mistake! The tool shown after flashing 'successful', but since then the Mix2s shows 'system destroyed - push power button to switch off' on booting. I get access by fastboot, but the bootloader is now locked....
I´ve tried to get access by deepflash, but the problem is, that if I connect it to USB the phone switches on and shows the mentined message - again and again. I´m not able to switch it off, to get the connection by qualcomm drivers to USB. I tried to push and hold the power button very long, push all buttons together and so on...
Has anyone an advice or can tell me about testpoints of the Mix2s ( if it has? )
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
When in edl mode, only nop and sig tags can be recevied before authentication.
Thanks!

In this thread, some users speak about test points. There is a photo of it
http://en.miui.com/thread-3123002-1-1.html
Edit: Method for Mi Mix 2, maybe this can help you...
http://en.miui.com/thread-1351514-1-1.html

You should send it to customer servt

You can try to contact xiaomi support, they can grant you access to unlock the bootloader without adding an account... However, there were only one or two guys in miui forum who were successful with that, for all the others xiaomi said they can't allow it

What happens when you try to unlock your bootloader? And why cant you unlock it again?

Enter Fastboot and unlock your bootloader again by using xiaomi mi bootloader unlocking tool.

same problem when i've flashed the beta, i had to unlock the bootloader again and the phone boots

Question "AP Fatsboot flash Mode (Secure)" screen

I Start asking for excuses by english
Well I have a device (Moto g7 play) to solve a problem that has already cost me days
In short, the device is locked on the "AP Fatsboot flash Mode (Secure)" screen, without the android symbol appearing;
If I try to enter fastboot mode with low volume and the power button, it restarts on the same screen.
The device is without an OS
manual processes and programs such as: rescue and smart assistant, RSD Lite and Reiboot do not work.
I'm desperate to fix this smartphone someone help me

vini__ said:
I Start asking for excuses by english
Well I have a device (Moto g7 play) to solve a problem that has already cost me days
In short, the device is locked on the "AP Fatsboot flash Mode (Secure)" screen, without the android symbol appearing;
If I try to enter fastboot mode with low volume and the power button, it restarts on the same screen.
The device is without an OS
manual processes and programs such as: rescue and smart assistant, RSD Lite and Reiboot do not work.
I'm desperate to fix this smartphone someone help me
Click to expand...
Click to collapse
AP fastboot flash mode should mode needed to flash.
Windows 10?
Open device manager
Is it listed like this?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Also there is a forum for this device.
Moto G7 Play
The Moto G7 Play is a 5.7" phone with a 720 x 1512p display. The Snapdragon 632 is paired with 2GB of RAM and 32GB of storage. The main camera is 13MP and the selfie camera is 8MP. The battery has a 3000mAh capacity.
forum.xda-developers.com

Thanks for answering.
Yes Win10
The Computer recognizes it as "Fastboot channel S / Motorola ADB Interface"
Could you give me the forum link? Of course I'll look, but in case I can't find it ...

FRIEND YOU ARE A GOD I RESOLVED FOR YOU BUT IN THE FORUM THAT MENTIONED THANK YOU SO MUCH

vini__ said:
FRIEND YOU ARE A GOD I RESOLVED FOR YOU BUT IN THE FORUM THAT MENTIONED THANK YOU SO MUCH
Click to expand...
Click to collapse
Great glad you fixed it.
Please change thread title to include [Solved]

Unbriking OP6. MSMdownload tool shows 'Status of connection: N/A'

I am trying to unbrick my friends phone. Phone decided to brick itself yesterday morning. SScreen is dead for the most part. Only when trying tp charge it sometimes Battery too low let the device charge for a while screen shows up. else nothing happens.
I have installed the qualcomm drivers.
I have downloaded the decrypted image.
I run MSMdownload tool. but the device connection stats shows N/A.
In device manager, Under ports
Code:
Qualcomm HS-USB QDLoader 9008
Shows up. But the device does not show in MSMdownload tool. see attached image.
what am I missing here?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

xeltos said:
I am trying to unbrick my friends phone. Phone decided to brick itself yesterday morning. SScreen is dead for the most part. Only when trying tp charge it sometimes Battery too low let the device charge for a while screen shows up. else nothing happens.
I have installed the qualcomm drivers.
I have downloaded the decrypted image.
I run MSMdownload tool. but the device connection stats shows N/A.
In device manager, Under ports
Code:
Qualcomm HS-USB QDLoader 9008
Shows up. But the device does not show in MSMdownload tool. see attached image.
what am I missing here?
View attachment 5291079
Click to expand...
Click to collapse
You have to be on Test mode on your computer. In Bottom right corner of your Computer should look like below. The Exclamation mark over the port name shouldn't be there.
Detail Instruction Has been been provided in the link below
[TOOL] MsmDownloadTool V4.0 International (Oxygen OS 5.1.5)
You can use it to revive your op6, if you can boot in fastboot and have done the stuff with drivers (qualcomm) MsmDownloadTool V4.0 International (Oxygen OS 5.1.5) May 2018 Android patches https://mega.nz/#F!CfBG0IgZ!Gmnu6B-a7yFyvMLNw_pz8w...
forum.xda-developers.com

I have the same issue even tough I am in Testmode.

change port from 25 or up to 1 or 2 its worked

pro change port from 13 to 1 or 2 its work

XIAOMI NOTE 4X PROBLEM

HI EVERYONE, HOPE YOU DOING FINE.
I HAVE XIAOMI NOTE 4X THAT IS NOW NOT WORKING, WHEN I PRESS THE POWER BUTTON IT VIBRATES LIKE IT WOULD START BUT NOTHING HAPPENS AFTER THAT, NO MI LOGO OR FAST BOOTING, I TRIED TO FLASH IT USING MI FLASH TOOL BUT THE FLASHING PROCESS TAKE JUST 2 SECONDS AND THEN IT SAYS SUCCESS, DON'T KNOW WHAT IS THE PROBLEM I INSTALLED ALL THE DRIVERS , BUT PHONE DOESN'T RESTART AFTER THAT. CAN ANYONE TELL ME HOW TO FLASH THE PHONE CORRECTLY?
THIS IS A SCREEN SHOT OF MI FLASH TOOL:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

CAN ANYONE HELP ME WITH THIS?

i want to explain the problem more clearly, when i press the power button on the phone it vibrates only, and then nothing happens, i tried to put it in fast boot mode but i couldn't.​i used the mi flash tool several times trying to resolve the problem but i didn't work, when i plug in the phone to the laptop the device id appears in device section in mi flash tool but the COM port doesn't appear at all no matter how much i tried, also QUALCOMM drivers are installed but they don't appear in device management when i connect the phone to the laptop.​please is there any one can help me?​

I had mido for a couple of years but nothing like this has ever happened to me. Try flashing in EDL mode or maybe try charging it.

AmmarHaseeb said:
I had mido for a couple of years but nothing like this has ever happened to me. Try flashing in EDL mode or maybe try charging it.
Click to expand...
Click to collapse
i tried but nothing works, in mi flash tool this"31e0ceea9804" appears in device section instead of COM port. and when i click on flash it takes just 2 seconds and then it says "success".

BV4900 Pro systemupdate and brick

Hello everybody!
Yesterday, on 28 of December, I had a massage on my BV4900 pro that a systemupdate is now ready to be installed.
After download of 2,48 GB file the installation went on, the phone started in the next step. On the screen was this white circle and the installation-progress was shown under. After the update was completted, the phone didnt start. The screen ist black. I cannot do anything with it. I tried to flash the firmware or at least the preloader with sp-flash-tool, but cannot. The connection to sp-flash-tool is with 100% but then I see under device-manager is "Media Tek PreLoader USB VCOM (Android)". So the flash-tool does not flash. I tried with volume buttons to stop the battery-loading, but withou sussess. What can I try more to save the phone?
Some more informations: The red LED ist on, when the phone ist connected to pc or power-supply. The phone was rooted. The last android version: 12
And maybe this picture will help:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Just a Hint:
Do not flash preloader! preloader is responsible for preloader mode (which used by SP Flash Tool)
Do not use "Format all + Download" option. Formatting whole emmc will brick device.
regarding your issue. follow the recommendations of your screenshot.

aIecxs said:
regarding your issue. follow the recommendations of your screenshot.
Click to expand...
Click to collapse
Yes, I did it already. Nothing helps.
I spend the second day with this problem and do not come forward.

you already tried another cable and another PC? then probably usb jack is faulty. you shouldn't flash anything via usb then!
I am not the one who told you - you could try other flash tools. do not flash, just try to read back for now...
https://www.xda-developers.com/bypass-mediatek-sp-flash-tool-authentication-requirement
https://github.com/bkerler/mtkclient

Somebody else, who maybe has an idea?

I found this discription of the error:
The phone seems always be on. With power button I can only "restart" it. How can I shut it down?
Is there a tool I can use for switch the phone off?
Or maybe cmd-command for shutting down the device on com-port? I cannot find anything in internet. Only with adb. But I have no connection to adb, the phone is over adb not rearchable.

Maybe someone can show me the test point for this smartphone?