Portable ADB ALL [ANDROID] devices - Android General

Have you ever needed to use ADB at a work PC or a location you could not "install" applications?
Unzip the attached file and click the RunMe.bat
I have tested this pulling logs, pushing/pulling files, flashing recovery, roms, and anything else I could think of.
I tested it on the M8 stock rom 5.0.2 but this is a generic file so it should be fine on most if not all android devices.
The idea came when I was at work and looking for a solution for a problem I had. I could not install anything on my work PC, so this came in handy, the only problem is that it was outdated, or seemed outdated for my needs.
find the zip file here https://www.androidfilehost.com/?fid=24052804347791558
This topic has been covered but is very outdated. I only found information from 2011 and 2013. The included information has since been updated by Google. I found it and included it, re-zipped it and now it is here for you to enjoy.
Thanks
to @Kickface, (where I first found this solution) wherever you went and any others who have created a truly portable (not minimal) solution to using ADB without installing anything.

dopy25 said:
Have you ever needed to use ADB at a work PC or a location you could not "install" applications?
Unzip the attached file and click the RunMe.bat
I have tested this pulling logs, pushing/pulling files, flashing recovery, roms, and anything else I could think of.
I tested it on the M8 stock rom 5.0.2 but this is a generic file so it should be fine on most if not all android devices.
The idea came when I was at work and looking for a solution for a problem I had. I could not install anything on my work PC, so this came in handy, the only problem is that it was outdated, or seemed outdated for my needs.
find the zip file here https://www.androidfilehost.com/?fid=24052804347791558
This topic has been covered but is very outdated. I only found information from 2011 and 2013. The included information has since been updated by Google. I found it and included it, re-zipped it and now it is here for you to enjoy.
Thanks
to @Kickface, (where I first found this solution) wherever you went and any others who have created a truly portable (not minimal) solution to using ADB without installing anything.
Click to expand...
Click to collapse
OMGGGGG this just may solve all my problems I had my personal PC but couldn't get HTC sync manager to connect...The only other PC's I have access to are either desktop @ office or my work "administrator password protected" laptop... TY, TY, TY in advance if this works!!!!

MAJOR PROBLEM!!!! Plz tell me someone can help??
M-FayeHTC said:
OMGGGGG this just may solve all my problems I had my personal PC but couldn't get HTC sync manager to connect...The only other PC's I have access to are either desktop @ office or my work "administrator password protected" laptop... TY, TY, TY in advance if this works!!!!
Click to expand...
Click to collapse
I know this is totally off topic, I'll report myself for it later....
So, I installed the zip file onto my work PC, a DELL Inspiron laptop running Windows 7 professional (I really cannot get too much more info about it now) sorry. My nooby butt just went and downloaded the file not checking the MD5 :crying: Totally a dumb thing a NOOBY would do. It started to get late & I had to get ready to go to work. I know I had the command prompt screen (Black box) running and I then left the computer. 8 hr's later I come home from work and the computer is locked as normal, I to proceed entering Ctrl+Alt+Delete combination as usual & NOTHING (panic setting in)!! I was concerned since it was frozen from something I done, also I didn't want to loose all the work I gathered that night prior (is the very least of my worries now)... I took out the battery to reset the computer, again like a dummy, I started Windows normally ignoring the other "safe mode, etc" options. I click on windows Chrome, NOTHING! Not even an option to open the program/app. Okay, I'm really panicking now WTH did I do??? I knew I did something wrong, so I reset the computer by battery again, put it in "Safe Mode" which did absolutely nothing as I couldn't "open desktop gadgets in safe mode". Now, I restarted the computer from the start menu... Started up completely fine, I have access to everything EXCEPT Chrome, Internet Explorer, etc. anything that is browser related has the administrator shield on the icon. However, I still cannot even click on the icon to run as an administrator even if I had the password!?!?
Is there any possible hope to uninstall that file and just maybe it'll go back to normal??? I cannot re-install Chrome or Internet Explorer due to the darn administrator rights!!!
I've searched to the ends of the earth since last night trying to find a solution, this is my last ditch effort resort for any possible suggestions to point me in the right direction. Luckily my friend was kind enough to lend me his laptop and my phone is in proper working order:angel: If I tell my IT guy what happened, I'll be in huge trouble, going on the 2nd laptop destroyed, 1st time really wasn't my fault, just saying so u don't think I'm continuously reckless.
Any help as always is greatly appreciated! Hoping someone has had this happen maybe:fingers-crossed: and just a slight point in the right direction (link, website, specific thread on forum) would b awesome?? Again, apologies on the "off-topic" content, I don't know what else to do & I feel as though XDA is THE ABSOLUTE BEST forum site for any Android help, apps, devs research, roms, etc. Thx in Advance!!

M-FayeHTC said:
I know this is totally off topic, I'll report myself for it later....
So, I installed the zip file onto my work PC, a DELL Inspiron laptop running Windows 7 professional (I really cannot get too much more info about it now) sorry. My nooby butt just went and downloaded the file not checking the MD5 :crying: Totally a dumb thing a NOOBY would do. It started to get late & I had to get ready to go to work. I know I had the command prompt screen (Black box) running and I then left the computer. 8 hr's later I come home from work and the computer is locked as normal, I to proceed entering Ctrl+Alt+Delete combination as usual & NOTHING (panic setting in)!! I was concerned since it was frozen from something I done, also I didn't want to loose all the work I gathered that night prior (is the very least of my worries now)... I took out the battery to reset the computer, again like a dummy, I started Windows normally ignoring the other "safe mode, etc" options. I click on windows Chrome, NOTHING! Not even an option to open the program/app. Okay, I'm really panicking now WTH did I do??? I knew I did something wrong, so I reset the computer by battery again, put it in "Safe Mode" which did absolutely nothing as I couldn't "open desktop gadgets in safe mode". Now, I restarted the computer from the start menu... Started up completely fine, I have access to everything EXCEPT Chrome, Internet Explorer, etc. anything that is browser related has the administrator shield on the icon. However, I still cannot even click on the icon to run as an administrator even if I had the password!?!?
Is there any possible hope to uninstall that file and just maybe it'll go back to normal??? I cannot re-install Chrome or Internet Explorer due to the darn administrator rights!!!
I've searched to the ends of the earth since last night trying to find a solution, this is my last ditch effort resort for any possible suggestions to point me in the right direction. Luckily my friend was kind enough to lend me his laptop and my phone is in proper working order:angel: If I tell my IT guy what happened, I'll be in huge trouble, going on the 2nd laptop destroyed, 1st time really wasn't my fault, just saying so u don't think I'm continuously reckless.
Any help as always is greatly appreciated! Hoping someone has had this happen maybe:fingers-crossed: and just a slight point in the right direction (link, website, specific thread on forum) would b awesome?? Again, apologies on the "off-topic" content, I don't know what else to do & I feel as though XDA is THE ABSOLUTE BEST forum site for any Android help, apps, devs research, roms, etc. Thx in Advance!!
Click to expand...
Click to collapse
I can tell you that it's not related to the files because I use them on my work PC all the time. I am working 10 hours days, 6 days a week. So the only time I can do anything out of the ordinary on my phone, it has to be at work.
That being said, have you tried system restore? I'm not sure if that requires admin rights, it might. On another note, tell the IT guy your internet explorer just stopped working, they love that. Because seriously, it's unrelated. The most he will do is uninstall and reinstall IE/Chrome. If that doesn't fix it, a system restore should. If that still does not, there is something off with the settings for internet access (I've seen that before). But if you are saying there is a shield/lock over an icon, that's new to me.
Also, I can install chrome at my work. It usually does not require admin rights, that and Firefox. There are also many portable browsers you can download from another PC and copy the zip file to the laptop, and run the app. Just search portable browser. At least this will help determine if the browsers installed got locked or if there is a network setting being blocked.
Let me know how it goes. This IS a bit off topic, but let's figure out what's wrong publicly so the mods can see there is nothing wrong with the zip I posted and then we can have our posts removed.

dopy25 said:
[/HIDE]
I can tell you that it's not related to the files because I use them on my work PC all the time. I am working 10 hours days, 6 days a week. So the only time I can do anything out of the ordinary on my phone, it has to be at work.
That being said, have you tried system restore? I'm not sure if that requires admin rights, it might. On another note, tell the IT guy your internet explorer just stopped working, they love that. Because seriously, it's unrelated. The most he will do is uninstall and reinstall IE/Chrome. If that doesn't fix it, a system restore should. If that still does not, there is something off with the settings for internet access (I've seen that before). But if you are saying there is a shield/lock over an icon, that's new to me.
Also, I can install chrome at my work. It usually does not require admin rights, that and Firefox. There are also many portable browsers you can download from another PC and copy the zip file to the laptop, and run the app. Just search portable browser. At least this will help determine if the browsers installed got locked or if there is a network setting being blocked.
Let me know how it goes. This IS a bit off topic, but let's figure out what's wrong publicly so the mods can see there is nothing wrong with the zip I posted and then we can have our posts removed.
Click to expand...
Click to collapse
Thanks for getting back to me, I appreciate it.
I'm glad to hear that it's not the file bc I cannot uninstall that regardless. We do have crazy blocks on all the computers at my work. I'm pretty sure it has to do with the sensitive information we have (a drug tx center so everyone's personal info is in our database). We can't even update the time on our computers, I have no clue why. I asked him once, he said something about giving that permission would open up another way to bypass security (I can't remember exactly).
This is my laptop, I never even bother bringing into work because I work so much from home. For example my login at the office has updated twice when at home it's still my old login password. The computer is physically in bad shape (it's been used & abused for sure) I'd prefer not to the bring it in for him to see so I plan on waiting to Friday night (IF ALL ELSE FAILS) and txtg him saying I absolutely need to work & see if he will do troubleshoot remote access! I hope that doesn't sound too horrible :-/
As I was typing this I just received an email to restart all workstations due to updates/ changes to the server done this weekend... Hmmmm it could totally be bc of this!!!!! Fingers crossed. I may just have to bring it in let it connect to the local server reset it, and bam good to go If not due to this I can almost guarantee it's the internet settings that I don't have access to!! But the portable browser should work...
I will still try all of your suggestions once I get home this afternoon and report back to you ASAP!!
Luckily I have my friends laptop to borrow & Dell had some good deals on laptops last night so I ordered a really nice one since I really need a personal computer again. Which I will also get an expense check for (bonus)!! But, won't arrive until 3/16. Until then I do have access to extra pc's here I could always swap it out, but I don't want to be scrutinized or punished for being sneaky, it's really not my character...
Again, I appreciate your input. Also, totally agreed on the "off-topic resolution" first and then delete our posts...
Thanks Again!

Yeah, I cannot get through the security on it.
When I look at the properties or try to repair Chrome or IE, it has an incorrect path, totally crazy looking.
\\localhost\C$\os(c\Users\mludford.....
I'm currently downloading a zip for a standalone browser. Hopefully that'll work...
This thread in general is totally crazy too, it looks like I replied like 3 or 4 times, I DID NOT :/ I tried twice & it told me that I didn't have access to the post, with a grey button over my original post you replied to, saying "Spoiler"!?! Very strange....

M-FayeHTC said:
When I look at the properties or try to repair Chrome or IE, it has an incorrect path, totally crazy looking.
\\localhost\C$\os(c\Users\mludford.....
I'm currently downloading a zip for a standalone browser. Hopefully that'll work...
This thread in general is totally crazy too, it looks like I replied like 3 or 4 times, I DID NOT :/ I tried twice & it told me that I didn't have access to the post, with a grey button over my original post you replied to, saying "Spoiler"!?! Very strange....
Click to expand...
Click to collapse
Needless to say it's not the settings or anything with the computer as I took it into work for it to "register" & update to the network settings... Nothing! So, I'm trying the above to see if I can't get around it. Thanks Again

Related

[Q] need help with UnBrickableResurrectorR40

I need some help. I will set up the scenario first. My Cap has had the unbrickmod performed on it about 8 months ago. I had the battery fall out ib the middle of a flash. I was getting the phone /computer "you screwed up a firmware install" animation. I tried to get it cleared up with Odin and now it is black screen no matter what I try. Can't get download, or recovery, and the usb jig won't even get it into download. I am completely unschooled and self taught with pc and phones and I think I have done pretty well. Now, I have taken another big step and after reading up on what to do next, I installed successfully, Ubuntu in my laptop (xp pro)and I can dual o.s. or boot either o.s. individually and everything seems to work fine. I downloaded UnBrickResrectR40, HIBL.zip, and java jre7.0.5. Ihave no clue about Linux or command lines,but after reading a million different claims on how to install these files i was finally able to get the java installed. But, I can't get the unbrickres file to install. I always get an error saying file not found by regex. Now I have copies in downloads,desktop, home, files, and have changed permissions and types(jar,javaw.exe,zip.gz) and still nothing. No forums or help pages help. They all give directions as if you know what you are doing already. They must figure if you got this far you are a tech or a dev, not a noob electrician who can't even type. I need some seriously slow,detailed,step by step,hand holding through this one, if someone has the patience. Back to the phone. The only thing that shows any life in the phone at all is when it is plugged into my laptop. It doesn't show up anywhere but under device manager. It shows under "universal serial bus devices" as, SEC S5PC 110 Test B/D , location 0,device is working properly,driver provider-libusb.org, driver date-7-13-2009,driver version-6.7.7600.16385, not digitally signed. That is it. I need some direction. What do I do now? Hopefully someone feels adventurous.Thanks
khkaiser13 said:
I need some help. I will set up the scenario first. My Cap has had the unbrickmod performed on it about 8 months ago. I had the battery fall out ib the middle of a flash. I was getting the phone /computer "you screwed up a firmware install" animation. I tried to get it cleared up with Odin and now it is black screen no matter what I try. Can't get download, or recovery, and the usb jig won't even get it into download. I am completely unschooled and self taught with pc and phones and I think I have done pretty well. Now, I have taken another big step and after reading up on what to do next, I installed successfully, Ubuntu in my laptop (xp pro)and I can dual o.s. or boot either o.s. individually and everything seems to work fine. I downloaded UnBrickResrectR40, HIBL.zip, and java jre7.0.5. Ihave no clue about Linux or command lines,but after reading a million different claims on how to install these files i was finally able to get the java installed. But, I can't get the unbrickres file to install. I always get an error saying file not found by regex. Now I have copies in downloads,desktop, home, files, and have changed permissions and types(jar,javaw.exe,zip.gz) and still nothing. No forums or help pages help. They all give directions as if you know what you are doing already. They must figure if you got this far you are a tech or a dev, not a noob electrician who can't even type. I need some seriously slow,detailed,step by step,hand holding through this one, if someone has the patience. Back to the phone. The only thing that shows any life in the phone at all is when it is plugged into my laptop. It doesn't show up anywhere but under device manager. It shows under "universal serial bus devices" as, SEC S5PC 110 Test B/D , location 0,device is working properly,driver provider-libusb.org, driver date-7-13-2009,driver version-6.7.7600.16385, not digitally signed. That is it. I need some direction. What do I do now? Hopefully someone feels adventurous.Thanks
Click to expand...
Click to collapse
Have you tried the Windows tool Windows32DriversAndCommandLineApp.zip ?
http://forum.xda-developers.com/showthread.php?t=1242466
Thanks for the advice
Thanks Silvertag, I appreciate the fact that you even read my post. I was running late for work, but wanted to get something on the boards.
I will check out the link you suggested. Much appreciated.

[Q] failing to root

I'm trying to root my tf700, and although I have Unknown Sources checked, and the USB debugging checked, I still get the error that it needs to be turned on. And then I get the daemon is not running message. Is there another way to root my Infinity?
Also, my Build is 9.4.5.21, so I'm thinking of nvflash. The problem is that although I've unlocked the bootloader, I still see I have a firmware update pending. I'm afraid to install the upgrade, lest it moves me to the later build, and thus prevents me from using nvflash.
Can anyone offer some help on my inability to root? And advice on the firmware/nvflash situation? Thanks...
Which root process are you trying to use?
1click root or debugfs?
Coming from the ground up
Thanks for the reply. I'm using the dbugfs.
Reggie777 said:
Thanks for the reply. I'm using the dbugfs.
Click to expand...
Click to collapse
Sometimes switching usb plugs on the PC works.
I know a lot of folks in the forum have said that trying on a different PC also works.
Are you working with Win7 or XP or something different?
It says Daemon isn't running. And then next screen it says Rooting failed. System partition was not found
I'm using Windows 7.
Please excuse the stupid question.. but should the tablet be on a certain screen while this is going on? Or should it be off?
Reggie777 said:
It says Daemon isn't running. And then next screen it says Rooting failed. System partition was not found
I'm using Windows 7.
Please excuse the stupid question.. but should the tablet be on a certain screen while this is going on? Or should it be off?
Click to expand...
Click to collapse
I suggest you re install android SDK. Download from here. Only install packages with android in it (should be 2)
http://developer.android.com/sdk/index.html
Reggie777 said:
It says Daemon isn't running. And then next screen it says Rooting failed. System partition was not found
I'm using Windows 7.
Please excuse the stupid question.. but should the tablet be on a certain screen while this is going on? Or should it be off?
Click to expand...
Click to collapse
Hmmm,
The tab should be on and connected as MTP I believe.
Is the tablet seen when clicking on the computer icon or in explorer?
Also check device manager to see if the tab shows up in there.
If the tab is plugged into a front USB (if using a Desktop PC) try a port on the back if available.
Oops edit!
Did you try downloading and installing the PCSuite from the Asus website?
Thats OK said:
Hmmm,
The tab should be on and connected as MTP I believe.
Is the tablet seen when clicking on the computer icon or in explorer?
Also check device manager to see if the tab shows up in there.
If the tab is plugged into a front USB (if using a Desktop PC) try a port on the back if available.
Oops edit!
Did you try downloading and installing the PCSuite from the Asus website?
Click to expand...
Click to collapse
I did the SDK install.... no difference. It is showing up on the PC. But I have not downloaded the PCSuite from Asus, since I've been afraid of going there, and getting tied up with the Sync issue. I had read that if I had the sync on, they can track the tablet along with reading the info, and even doing some extreme things if they felt I deserved it. I didn't know if I was supposed to register it before I unlocked it. or what. The odd thing is that I have unlocked it successfully.
i've also moved the usb connector to different ports but with the same result. I do notice, that now, it says after saying daemon is not running, that daemon started successfully. But then, it says Rooting Failed.... System Partition could not be found.
Is it possible to install nvFlash on an unlocked device, but one that is not rooted?
Lemme see here...
Ur right clicking the .bat file then running as admin then?
http://androidroot.mobi/t3_nvflash/
...on the mobi blog it just says to be unlocked and have nerves of steel.
I had a nightmare getting the Win 7 drivers to install.
I eventually gave up and used Linux...
Nerves of steel is right. I'm about to try the procedure on another computer. Hmmmm. Is the sync app from Asus relatively safe to use? someone said it worked for them after they installed it.
If I'm sweatin' it now,... can you imagine how I'm a tremblin' with the nvFlash install ahead of me?
My ol' gTablet never gave me this much stress. :highfive:
Reggie777 said:
Nerves of steel is right. I'm about to try the procedure on another computer. Hmmmm. Is the sync app from Asus relatively safe to use? someone said it worked for them after they installed it.
If I'm sweatin' it now,... can you imagine how I'm a tremblin' with the nvFlash install ahead of me?
My ol' gTablet never gave me this much stress. :highfive:
Click to expand...
Click to collapse
Man I know...I was always afraid to do anything at first.
I was pretty afraid of a 500 dollar lesson gone wrong...then one day I said "what the hell man up"
So here I am today a satisfied customer!
I have PC Suite installed, I had registered and unlocked so Big brother Asus had my number from the beginning.
Seems like PC Suite is the only way in certain cases.
Coming from the ground up
Well, it did not work on the second computer... And now, what I get is, daemon does start, and the cursor moves to a new line, and just blinks back at me ... ouch. Didn't I just feel silly waiting for 30 minutes, and nothing happened? Reminded me of the cat that just sits and watches the curtains move. Ah well. So, I am unlocked, but also unrooted. Does anyone happen to know if the one click app works with our Infinity? I getting desperate enough to pay. :crying:
HTTP://forum.xda-developers.com/showthread.php?t=1824713
Was wondering if you had seen this thread...
I was reading thru the debugfs thread and there it was.
Forgot all about it...there's got 2 be an answer.
We need to get you fixed up!
Coming from the ground up
I'm Rooted!
Whew!... Thanks to all who responded and pointed me in the right direction. It was not pretty. I encountered a number of errors. I'll list them below, in case anyone else is having the same problem/s I had.
1. After you choose "1" from the debugfs menu, it ends up saying "Rooting failed. System partition was not found." Check to see if the device is being seen. How you do this is go to the same directory you unzipped the files you downloaded, and start a command line from this directory. The question was how? Press the Shift key, while right clicking on the directory where adb.exe is, and you will get a window with a prompt. This is a very useful window. type "adb devices", and you should see some datafline" and then a code number followed by "device". Naturally, mine was not there. If this is not there, type " adb kill-server" Then "adb device", and hopefully, if the stars align correctly. You will see your device there with it's code. If not, then you have to check the device manager, and check the drivers. To do this... Go to the start box in lower left of window bar, and type "device manager". The file will be listed, click on it. and you should see your device listed. I found it twice.. once by itself using, and again under Portable Devices. I clicked on these, and updated the drivers to the ones in the same directory with the files you unzipped. Hopefully that will work. If it doesn't you might have to uninstall them, and reinstall them.
2. After all that, you still might not get past option 1 in the menu. Possible error, "more than one device found". So, you have to check if anything else is interfering. [I'm not sure if this was the culprit but as soon as I removed my Zunes, I was good to go].
3. And then option 1 gets a little further along and goes off to never never land. So... I moved to option 2, Manual entry of the partition. It warns you to not go into this section if you are not sure. Naturally, I shook off my cold sweat and plunged ahead. The address I used, from another post was "/dev/block/mmcblk0p1", and that seemed to work.
4. Then.... the app got stuck trying to reboot the device. You can check if it is seeing the tablet by the "adb devices" check. If is not, you have to fiddle with the drivers again.
5. Finally, after a number of tries, and a lot of colorful venting... it went through... and I was rooted.
Whew! It was ugly... But finally. :fingers-crossed:
I relate my story to encourage anyone who might be discouraged by the roadblocks. Hang in there, and as they say... "Never Give Up. Never Surrender!"
Now to tackle installing nvFlash. I have my blankie all ready.
AWESOME!
Way to go slugger!
So was another media device "Zunes" plugged up in another port?
You have done well!
It's pretty fulfilling to wind thru all this and come out with a desired result.
Thanx for the low down.
It will mean a lot to others having trouble.
Thumbs raised kiddo!
nvFlash adventures...
Again, thanks to the wonderful support from the wonderful folks here.:highfive:
Just to end on an even higher note, I wanted to add that I was able to install nvFlash, and generate my "Resurrection Files". I don't know if this is allowed on this forum to include a link, but I followed this video
http://www.youtube.com/watch?v=J3ypzUaKxvo&feature=colike
which seemed to anticipate some of the very same roadblocks I encountered. So, now, I can look about that "firmware update" notification that keeps flashing in my bar.
My Infinity adventure continues...

[Q] Galaxy Ace (S5830i) headache with stock email deletion

HI guys, I'm hoping you can help me with a problem that's led me to start threatening my galaxy ace (S5830i) with a hammer.
Actually it's not the phone's fault it's purely my own stupidity, but none-the-less I'm here for help because I've spent all day and night trawling the net, trying to figure out how to proceed to resolve my issue on my own but I simply cannot make sense of the conflicting information I'm finding.
I promise you thing thing if nothing else, I have tried my very best to read around a hundred other forums, pages, and how 'to's but I'm finding that I have no resolution that I can work with because either:
- The tutorials turned out to be for the S5830 - not the i model - when I got to the forum
- The youtube videos all seem to be spoken in accents I cannot understand or not explained clearly, or are too technical
- Links I go to to get apk files etc are broken, wrong or leading me up another path I cannot follow
- Software does NOT look on my screen as it does on tutorials or websites (SDK for example)
- The people explaining the resolution type with such poor English I cannot understand what they're actually saying
- The solutions that work for others are too technical or advanced for me to understand and I'm finding it difficult to learn as I go (apart frm the root instructions which I found quite easy)
Anyway, I'll start at the beginning:
I have a samsung galaxy ace (S5830i) running:
- Gingerbread 2.3.6
- Baseband version S5830iXXLK1
- Kernel version 2.6.35.7
- Build number GINGERBREAD.XXLK3
I've already rooted it so I have superuser access, and I managed that perfectly well on my own
I installed titanium backup and somehow I managed to uninstall the stock email that comes with the phone. I think this is my problem because I now cannot download anything from google play, nor can I add a new gmail account to do so, so I'm stuck in no mans land not able to use googleplay (because my gmail account is now missing from my phone) nor can I seem to figure out how to get th apk file directly into the phone so that I can start fresh.
I'm also absolutely stuck on how to flash the phone and start again because nothing I seem to read is explaining it in simple clear terms that a layman can understand. When I do find a simple explanation, I find it's only for the non 'i' version of the phone, or if I find a simple instruction it's zip files for the rom do not contain all the files I need to use with odin v1.5
Also, there are conflicting explanations on flashing the rom on different forums/sites so I dare not use one over the other because another one contradicts it. I do not want to ruin my phone as right now it still basically works for now as a phone.
In my phone menu, the gmail icon is still there, just not the icon/app that said "email". The icon is now missing from my menus and with it there is now no way to use the play services without a gmail account on the phone.
When I click the gmail icon, it stats to open and then just shuts off quickly, not opening gmail, so I'm pretty sure all this is due to me deleting the email app using titanium backup.
Make sense?
What I'd really be grateful for is if on of you guys could help me out and explain in very simple terms what I need to do to either install the apk directly (preferred) so that I can add a gmail account to the phone and get access to google play again, or failing that a simple how to flash the rom with stock gingerbread, together with links to software that's known to be bonafide.
I am literally being driven mad going around in circles on forums and sites to keep going back to square one.
Any help will be very gratefully received. Or I'm afraid this may mean I'm going to smash my new phone int a wall and never use a smartphone again, because obviously I'm too stupid to play around with them on my own.
I really appreciate your help if someone would be able to invest a little time here.
Thanks very much for your time, guys
Jobeeey
additional info
Right, these are the instructions I found on this forum, but I'm unclear if I'm approaching this right..
Flashing s5830i with Odin v1.85
1.Turn off the phone and put it in Download mode by pressing Power+Volume Up+volume down.
2.Open Odin v1.85.Run as Administrator!.
3.Put the files in Odin and don't touch the settings
4.If it's a one-file firmware put it in PDA section.
If it's multiple put the files in the correct section.
5.Click start and don't touch the phone!Don't turn off computer and don't unplug the phone!It will reboot automatically and the first boot will take some time,so don't panic!
Click to expand...
Click to collapse
I've found a rom (which is a single file) and if I'm reading this right I place that in the PDA section of Odin after installing the usb drivers onto my pc (done that and windows recognizes my phone in the sense that it isn't now hassling me for drivers every two seconds).
Ok.. so I seem to have got the correct rom for my specific ace model.. and the instructions seem to be that I now:
1) Connect usb cable
2) Boot my phone into download mode (I can do that I think).. but at what point do I press vol down to download a new os.. before or after pressing start in Odin?
3) Open Odin and add file as in my attached screenshot (I can do that)
4) Click 'start' in Odin
5) Wait for my phone to reboot
And that should be job done, the phone should be flashed with the stock rom again and that should get me back on track, right? Or am I about to screw up my phone and ruin it even further?
Thanks for reading. I hope someone can advise if I'm doing this right as I've seen other forums say that I should tick the 'Re-partition' box, and other that say I shouldn't, and this one says nothing about it at all.
This is one of the tings that's confusing me, and once I'm now flashing a phone for the first time it's flippin scary to do it on my lonesome!
This is what I mean..
I've just tested going into download mode with odin ready, and the phone gets there (vol up+down + power on).. but each time it gets into download mode it seems to disconnect from odin and no com port is open. I get the windows device disconnected/connected beeping and the connection seems to sever.
What the Fffff...
This is exactly what I'm talking about.. nothing seems to be working like it's meant to be and I'm getting nowhere with any instructions I can find after god knows how many hours researching this.
:crying:
update (lol)
Mornin all,
So, just in case anyone finds this useful..
The flashing problem is kind of irrelevant now because:
A) Odin (tried several versions) simply will not stay connected to my phone when it boots into download mode, and having checked many tutorials for this it sees that this is a problem some of us cannot get past.
Anyway, one of the methods to resolve this was to wipe the cache and clear all data etc, which I did, and now my phone is stuck on the "pres the android" screen, and my phone will no longer get past that. Tried pressing clockwise in all four corners but still nothing.
No probs.. so we move on to a new step of trying to split the roms via cygwin, but guess what? Every single time I try to download the cygwin files, that freezes at about 98% and will not download, no matter which mirror I select.
So, this is what I call a curse that isn't going to be lifted by me no matter hat. It's not not meant to be.
Therefore, what I'm going to do is take it to a local shop that unlocks mobiles and give it to them to flash back to stock rom for me.
If that doesn't work, do you know what I'm gonna do?
Nothing. Because there's nothing you can do when the processes do not follow the same progress as they do in the tutorials.
I hope other novice S5830i users save themselves all his time and trouble and don't bother following the same process and become locked out of their phone at the touch android screen.
Update
Yipee,
Right, I stumbled across a solution that worked for me.
What I did was get my 2gb msd card that came with the phone and slapped MindCR v1.0.12 on the card and whacked that in my phone (this bypassed not being able to get a new rom on the sd card as it wasn't unmounted before the crash, so my pc wouldn't recognise the date to put it on via the pc).
Then I updated the rom from that 2gb card (vol up + menu + power to get into recovery mode) and it took it a few minutes to update the firmware and give me back the full use of my phone, and with a shiny new os on it. Whoop!
I didn't bother with CWM as I'd forgotten to add it before flashing, but it worked none-the-less and I'm now back in business (wiped it manually).
As it turned out this version of MindCR works really well so far as I can tell. I realise there are updated roms now but I've come to the conclusion after the scare I had that if you're not entirely sure what you're doing, it's best to leave it alone if it ain't broke.
SO.. now I have a phone with what seems to be a better os than the stock and less bloatware on it, no phone problems I can see after thorough testing... and from what I can tell it turned out to be better than it was before the disaster.
And I learned a bit in the process. Like for example, don't feck around removing apps from smartphones with titanium unless you've backed them up and you're prepared to stress out for over 20hrs wondering what to do about it.
And, also, don't expect much help from a forum because you may not always get it. << That' not a dig at xda by the way. It's just a BIG forum so your threads may not be seen by the right person before they get buried in past pages.
Hope my little journey helps another unsuspecting S5830i user who comes across the thread.

[Q] Tablet stuck in password screen + recovery mode doesn't work

Hello,
I'm sorry to bother you with an apparently repetitive thread, but I assure it is not.
I've been dealing with this problem for over a year now. Of course there were times that I simply gave up, but every now and then I searched all over the internet (seriously; very resilient, I am) and tried everything. Nothing seems to work.
The issue is: one day I was reading something on Google Reader and the tablet restarted. When it came back, it was in this password screen.
[AS A NEW USER I COULDN'T POST THE IMAGE - please see attachment ending in 41]
Detail: I had never, EVER set any kind of password. I don't do this with any of my devices unless I'm obliged to (as in Windows 8, this big piece of shiite).
So the thing is: I did not set a password, I did not choose to ask for a password in any situation and there isn't a single combination that I haven't tried. The thing doesn't even ask me to stop -- like 'hey, you've tried your 30k input, I think you should stop now'.
Now, for you not to start cursing me, I tried EVERYTHING that is basic and post-basic to fix it. I did wipe the data, I tried flashing another ROM, I did cold boot, factory reset, EasyFlashed, nvflashtf and whatnot. I swear to GoogleGods that I, as a non-expert-but-very-keen-on-technology, could.
Another thing that happens is when I try to enter the recovery mode, after using the nvflash, it doesn't work. The image that appears to me is this one:
[SAME THING -- attachment ending in 38]
Again: I'm not a complete noob. I know how to get into things; all I need is a simple guidance. I'm really sorry if this has been posted before and only I couldn't find it, but I won't be so if someone helps me to get it and solve my problem. I can't stand this anymore -- now it's just a matter of pride.
Thank you all.
This happened to me on my SL101 after I flashed a ROM of some sort. I used ADB commands to push the stock ROM back to it and to push another Recovery to it. Mine was in worse shape, Recovery loop, and then I finally got it to where yours currently is. My physical nor on screen keyboard would even work. Look up some ADB commands, perhaps you already know them, and attempt to either push the stock ROM or a new Recovery blob back to it.
D
DatDude123 said:
Look up some ADB commands, perhaps you already know them, and attempt to either push the stock ROM or a new Recovery blob back to it.
D
Click to expand...
Click to collapse
Yeah, well, y'know, I'm not at this level yet, but I'll dig into ADB and stuff.
I tried to use this sometime in the past, but my computer was so bad back then that I had to give up to keep my sanity. Now I've got a fairly good one (very good, considering the few things I use it for), however much less time.
Tonight is the night, though. I'll study as much as I can and I'll fix this ****. Any tip you may remember now would be useful.
Thanks.
I'm struggling with something even before I start: there's no way I can get access to the system and turn the USB Debugging on.
I know I'm not getting much attention, but I won't give up. Please just do not accuse me of spamming; I'm just a desperate geek that has been kept away from his toy.
Alright, after the childish speech, here's the latest update: I cannot use de ADB thing because there's no way I can turn on the USB debugging mode.
Or is there? The latest news is that I can get access to some system files through the ASUS File Manager (turns out it still reads the MicroSD Card, even though I could not update the device this way). So, technicians, is there a way to hack into this beast? Fu ck, I don't even know how to call it anymore.
There isn't much I can do with this File Manager. Mostly visualize the folders and rename this and that (which is the only thing I reckon might be useful).
Jesus, I'm sleepy, I can't even write properly anymore. Please someone help me. It can't be that hard.
maycondimas said:
I know I'm not getting much attention, but I won't give up. Please just do not accuse me of spamming; I'm just a desperate geek that has been kept away from his toy.
Alright, after the childish speech, here's the latest update: I cannot use de ADB thing because there's no way I can turn on the USB debugging mode.
Or is there? The latest news is that I can get access to some system files through the ASUS File Manager (turns out it still reads the MicroSD Card, even though I could not update the device this way). So, technicians, is there a way to hack into this beast? Fu ck, I don't even know how to call it anymore.
There isn't much I can do with this File Manager. Mostly visualize the folders and rename this and that (which is the only thing I reckon might be useful).
Jesus, I'm sleepy, I can't even write properly anymore. Please someone help me. It can't be that hard.
Click to expand...
Click to collapse
For some reason i thought you were on th sl101(slider) so i didnt comment. So heres the deal, any fix is going to be data destructive(nothing you can do at this point as even if you manage to pull data from the tablet, it will be encripted) You need Easyflasher(dev section) follow the instructios there (basically donwloading stock firmware from asus and by using nvflash in apx mode it will re-partition storage, and upload the stock firmware to the tf101)
If you hit any problems, post them here and ill help you further
Edit: just read you post more, if you tried easyflaher and it didnt work, please post the details of what you tried within easyflasher.
Its a strange issue, if it happend to me and id tried the things you already have, this is what id try:
-Flashing ubuntu from the dev section(i known very little about how nvflash works but it maybe only re-partitioning certain partitions, ubuntu i would imagine would require a full re-partitioning)
-alternativly (or on top of the previous idea) use one of the ubuntu installers(OLiFE on ubuntu worked the best for me, but franks tools/ newer software based on franks tools should work fine) and flash the Prime! rom on its own.
If these dont work, your last resort is asus - but thats a long shot lol
maycondimas said:
I know I'm not getting much attention, but I won't give up. Please just do not accuse me of spamming; I'm just a desperate geek that has been kept away from his toy.
Alright, after the childish speech, here's the latest update: I cannot use de ADB thing because there's no way I can turn on the USB debugging mode.
Or is there? The latest news is that I can get access to some system files through the ASUS File Manager (turns out it still reads the MicroSD Card, even though I could not update the device this way). So, technicians, is there a way to hack into this beast? Fu ck, I don't even know how to call it anymore.
There isn't much I can do with this File Manager. Mostly visualize the folders and rename this and that (which is the only thing I reckon might be useful).
Jesus, I'm sleepy, I can't even write properly anymore. Please someone help me. It can't be that hard.
Click to expand...
Click to collapse
If you can't get into anything, but you can enter APX Mode, but NVFlash doesn't work, then I'm not sure anything will as NVFlash completey deletes and recreates all the partitions on the drive
So unless you have been unlucky and downloaded a bad version of an NVFlash ROM....
I know you say you have used NVFlash but I`ll stick this here anyway
The way I restore is:
Connect tablet to PC and make sure the tablet is turned off (Make sure it is the only USB device connected other than keyboard/mouse)
Hold Volume Up + Power for a few seconds until you hear the USB connect sound on the PC, release the buttons, you are in APX mode
Install APX drivers if you have not already
Now extract this
http://www.xdafileserver.nl/Files/Asus/Asus%20Transformer%20(TF101)/STOCK%20ROMS/ICS%20.27/NVFLASH_ICS_9.2.1.27_WW_NOROOT.7z
And run "download.bat"
I think you should see some text appear on the tablet screen, and progress will be shown in the command prompt window on the PC
Wait for it to complete 100%
Its been a while so I can't remember if the tablet will reboot on its own or if you need to hold power for 30 seconds to get out of APX mode
Either way, make sure it is completely finished and reboot the tablet
Only thing I can remember going wrong with NVFlash was the first time I rebooted after a sucessful boot, it would hang on a black screen
Just hold power for 30 seconds and then power on normally, done, if it has worked you have your tablet back, if not, I think its a hardware issue > see asus
Im very keen to get this fixed/ find the issue as uptil now I thought the tf101 was virtually software invincible, you need to pay attention to what the nvflash process says, the one thing I can think of as to why nvflash didn't work is it can't write over encrypted partitions although that would make no sense why it wouldn't.
Just a suggestion... make sure you're not docked. Some people report issues when nvflashing while docked (I can't replicate those issues except with the Tubuntu tool).
Is there a solution?
I also have an error! see picture

[Q] S4 Help needed (Warning: Long story)

Hey guys, let me just start off by saying I have spent almost 8 hours straight today trying to figure this out and dig myself out of a hole I've created for myself, that being said, I'm going to try and be as detailed as possible so you guys know EXACTLY where I am and what I've tried. This post looks long but that's because it is. It's pretty much my entire day's worth of trouble typed out. So just bare with me and see if you guys can help me out here!
I have a T-Mobile Galaxy S4 model: SGH-M919 it has Android 4.4.2. Now on to the problem: I've had this phone for almost a year now and a few months ago I rooted it. Did a simple Youtube tutorial and used Odin to do the work and everything worked out fine. A couple months down the road (yesterday), after using the phone like a teenager, downloading apps and cluttering it up it started to slow down and not run some apps. After thinking about it I decided to factory reset it. All of my contacts, photos, and videos were backed up on Google so I thought "why not?" Well, this is where $#!% hit the fan.. being rooted then factory reset, right before the phone came online it had me answer two questions about the root. Something to the effect of "Do you want to keep root? (This option is not reversible)" I thought since I wasn't using the features I originally rooted the phone for I figured nah just get rid of the root. So the phone did its T-Mobile boot up and started the Initial setup.
Everything up to to this point was fine until I wanted to log in to my Google account during the setup. Please understand that where I am I have full 4G LTE coverage and have access to a pretty fast and sturdy wifi connection. Well, when it came to the google sign in I entered my email and password and it came up with a message reading "Can't Sign in - Can't establish a reliable connection to the server" (believe me i wish that was the only issue) so after reading that, I thought I'd try with my wifi.. nope. Same thing. Since neither my 4g or wifi worked I thought it was Google's servers so I tried again this morning, same thing. (keep in mind at this point i think my phone isn't rooted anymore.) I call the t mobile store and they give me a technical support number, so I call it and I tell them i cant sign into Google. The gentleman told me he cant do anything because he can tell my phones been rooted. Only thing he suggests is to contact Google, well, the customer care number just tells you go to google.com/support and there's nothing there about my problem.
This is where I dig my hole even deeper. I tried another factory reset and up in the top left corner i still see that root text. Even the rooted android symbol pops up before the Samsung logo or t mobile. Since I saw that I thought "ohh it just didn't get unrooted all the way." I look up ways to completely remove a root and a lot of them require plugin your phone into the computer and using Odin to flash a stock firmware on to the device. I went to plug my phone into the usb port but my computer didn't recognize the usb device, having experienced this a long time ago I searched around for the latest Samsung usb drivers and I installed those. Device still isn't recognized. Let me just note before people tell me to use MTP mode or Developer tools> usb debugging or connection mode.. The only thing that happens when plugging my phone via usb is the phone starts charging and my computer makes the trumpet noise like something is plugged in. Other than that, there is NO notification of it being plugged in. The reason i stress this is because I called Samsung technical support at this point and the guy (not gentleman) treated me like a 5 year old and ran me through all of these options after i told him I already did everything he was suggesting, including downloading Samsung Kies 3 and having it install the drivers. It does not pick up the device either.. at this point I looked up ways to remove the root without the computer. I found out you can just go into the root app "SU" or something and theres a remove root option. I jumped on that opportunity and had it removed. I restarted the phone and all the problems still persist, it even still has the root text on the top left when you factory reset it again. However now, even if you factory reset and select the option "keep root," thinking it would bring back the"SU" app it does NOT.
So lets recap. I have a phone that thinks its rooted and even appears rooted to t mobile but doesn't have any of the root apps or privileges or capabilities to fix my Google log in issue (like the host file in filemanager). And I can't re-root to get that app back because none of my 3 usb ports, 3 different usb cables (one being the cord that came with the phone), or any of the ports/cables on someone else's computer will recognize the darn thing to work on that way! I have all these issues that are supposed to fix each other but I can't do any fixing because they cancel each other out too... I'm at a dead end.
In case this isn't the right forum/website/thread/post area etc.. I have this whole message saved in Microsoft Word document so I can repost it anywhere you guys might suggest better results. Any help/advice will be much appreciated.

Categories

Resources