[Q] My huawei g700-u00 cant start - General Questions and Answers

Hey, im new here
I have a terrible problem, I downloaded the package with the stock software for Huawei G700-U00, but after the installation by the SP tools, the phone does not get up, Only at roughly 10 seconds vibrates and so around with black screen. if you have it than share me a pack for SP Tools with proper soft for g700-U00. I beg for help

Related

[Q] Xtouch x507Q

My phone stuck on Android logo after i rooted and installed some custom fonts. And I have been trying to restore with the tools http://www.xtouch.ae provided with their stock firmware. That is SP multiport download tools. I tried everything as they said and the only thing i can't change in tool is Two side download with 2 options First site [UART] and second site [USB], tools choice second-site [usb] and can't select on first-site while xtouch said to choice first-site.
Any way, I scatter files and start all, times continues counting, but nothing been downloaded to my phone.
Please help

[Completed] [Q] Need Help for Fixing My Xperia SP (C5302)

Dear Friends,
I am Arindom Samajdar from India. Though I did not have any theoretical learning over android programming, I got a lot of helps & knowledge from XDA Threads on this specially on rooting of android phones. And truly speaking from following the guides of this forum I really rotted my Xperia SP (C5302) successfully about 6 months before and installed CM11 Rom via CWM recovery mode in it.
I was using it flawlessly till 10 days back also. But 10 days before I planned to roll back it to its stock Sony Rom as I was planning to sell it & get a new phone.
But at this time I did not studied mutch & simply started to flash the .tft file of the stock rom which I had prepared long back by the help of Flashtool, when I was rooting my device first. But this time during flashing the file there gone something very wrong and the flashing could not completed over night also & unfortunately during this process battery of my phone drained out & the flashing interrupted. When I checked my phone in morning, I found that it is in switch off condition. When I connected it to charger, first it shows bright green light in its notification light (like it gives while connecting in Flash mode), after 1 or 2 mins it gives Red light with SONY logo in its screen & stayed as it is for another 1 or 2 mins. Then again green light and after some time again red light with SONY logo. And continues this loop. While I tried to switch it on it just vibrate & gives SONY logo on screen, nothing else & after some times goes off.
After several studies over the websites & XDA forums, I understood that there was a error occurred while flashing Kernel. But when I tried to fix it by the methods suggested over the webpages, I got nothing to work for my device as for every process (be it by Flash Tool or by CMD window of windows) the flashing is not being started at all while I am trying to flash the Kernel & after an hour also when I am disconnecting my phone, CMD or Flash tool is showing error of Flash failure & stating it as "Too many Links". I can't understand what this meant to.
My device being connected with PC via Flash Tool both in Flashmode & Fast Boot mode, that means my device is only soft bricked & I am sure that there must be some way to get it back working.
Please help me guys..
Hi, thank you for using XDA Assist. See if this helps, http://forum.xda-developers.com/showthread.php?t=2708815 Also, maybe this, http://forum.xda-developers.com/showthread.php?t=2311964
Hi Friend, Thanks for your reply. But my issue is not with the ftf file. I am having the ftf file. My issue is flashing of the same.
Whenever I am trying to flash the ftf file it does not go beyond "Flashing Data" stage. And when I try to flash only Kernel, it does not starts yet.
Sent from my Nexus 5 using XDA Free mobile app
Thread closed.

Huawei mate 7 screen turn to black

i need help
my phone : Huawei mate 7 TL10
firmware: 4.4.2 kitkat
my problem started before 2 days ago
when the brightness get full the screen turn to black or turn off
when i open it , screen been like a flash light ( open for one second )
i try to format the phone but i can't in company logo it frozen or not open
and i can't find any way to make a firmware with pc
any Suggestions
any thing .. i need help with that problem

[Completed] Doogee X5 Pro Bricked

Ok, i have a doogee x5 pro phone and i tried to root it by flashing twrp recovery using sp flash tools. While flashing i got the error "PMT Changed for the rom it must be download". So i did a small research on internet and i found out that i needed to format everything except bootloader. This succeded. So after that i tried to install the firmware with this succeding to. Unfortunately the time i tried to turn phone on it was dead. SP Flash Tools wont detect it anymore. Please help me cause the phone is not mine and its brand new! I can rate my self as moderate android user. :crying:
i think i have a bigger problem... I downloaded a stock rom for doogee max pro(cause i just realised it wasnt just pro it was max pro) and it didnt seem to be recognised again. Any help would be appreciated. I constantly keep trying to raise it from the deads. Thanks!
Ap0s said:
i think i have a bigger problem... I downloaded a stock rom for doogee max pro(cause i just realised it wasnt just pro it was max pro) and it didnt seem to be recognised again. Any help would be appreciated. I constantly keep trying to raise it from the deads. Thanks!
Click to expand...
Click to collapse
On mtk devices a preloader is independently installed, it should be almost impossible to destroy, I owned a x5 pro and had best success to flash it with sp flash by taking out the battery, press flash button and plug it in...
The second huge issue I see is when you used the specific flash tool format option you very, very likely killed the nvram partition which contained the imei, so you'll have to fix this too by generating a new one and using mtk engineer mode which is well described and to find on Google..
But let's go step by step. Check without battery, or if it's a non replaceable you'll need find the reset button..
i have tried before without battery and i tried just now but nothing. Its very weird it was detected before and now no in same and another machine. I am pretty confused and stressed. Hope i didnt do any physical damage.. :crying:. THANKS!
starting to get pretty stressed omg! and is there a difference between MT6737M and MT6737?
i came to the point im starting to lose my mind... tried everything i could, i have 5 days left to repair this phone and i dont wanna pay 85 euros for this. SP Flash Tools wont detect the phone. Tried almost 5 different scatter files,2 different PCs and different mtk drivers. Im losing my mind already
UPDATE: I almost fixed it! I had flashed wrong preloader so phone wasn't recognized by SP Flash Tool. I fixed preloaded with a little trick from here: link. After that i flashed stock rom downloaded from doogee.cc but phone will not boot resulting in a total black screen. When i hot Power + Vol Up it takes me to another screen:
Select Boot Mode:
Recovery
Bootloader
Normal
Doesn't matter which boot mode i choose i just get a total black screen which means i get nothing. Idk what is happening! Any further help would be appreciated! I constantly try to bring it back working with little success and small improvements.
Last UPDATE: FIXED my phone had no juice left inside so couldnt complete boot proccess. Now its all good running Btw someone must pin this META trick link i send on my previous post cause im sure more people out there have preloader issues!!! Thank you everyone!!
Sam Nakamura said:
On mtk devices a preloader is independently installed, it should be almost impossible to destroy, I owned a x5 pro and had best success to flash it with sp flash by taking out the battery, press flash button and plug it in...
The second huge issue I see is when you used the specific flash tool format option you very, very likely killed the nvram partition which contained the imei, so you'll have to fix this too by generating a new one and using mtk engineer mode which is well described and to find on Google..
But let's go step by step. Check without battery, or if it's a non replaceable you'll need find the reset button..
Click to expand...
Click to collapse
And yes i couldnt flash it with battery only with!

huawei honor bee

hello can someone help me with my huawei honor bee cellphone?
when i turn it on it just goes to the logo screen and on top there is a red text saying
"please check download state, last download maybe not completed"
kchingx said:
hello can someone help me with my huawei honor bee cellphone?
when i turn it on it just goes to the logo screen and on top there is a red text saying
"please check download state, last download maybe not completed"
Click to expand...
Click to collapse
tried flashing with research download and upgrade downgrade tool from spdflashtools.
got it to flash firmware v105. but after flashing, blank screen won't power on. also cannot go to recovery.
tried to flash it again with different version, did not go thru anymore and cannot go through any firmware versions.
stuck at FDL2 failing.
tried android usb drivers and spd /sci drivers still stuck at fdl2
please help.

Categories

Resources