Related
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
Xperia C with red light softbrick
MicroUSB Cable
Sony Update Service
Click to expand...
Click to collapse
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
I flashed a faulty recovery using mobileuncles and there was no signs of life other than a red led liggt, and holding power + volume up works just fine and it went into flashmode.
I have the same issue.
I organized xperia light rom for our xperia c, I flashed it from custom recovery. Phone is completely dead now.
There is a just red light, phone does not go into download or fastboot mode. Pc Companion, Sony Update Center, Wmshua Flashtool do not recognize the phone.
Any suggestion with that?
I don't have warranty, my last option is to pay money for technical service.
this worked for me but instead of POWER+VOL UP i used POWER+VOL DOWN
thanks
thank, i like this forum
worth to try... (hope it won't happen to me :laugh: )
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
seiferfury said:
I have experienced this too, however, instead of using the Sony Update Service, I used the Sony PC Companion. At first it was not working, so I did a hard reset on the phone (press the button at the back). I held the power+up button while inserting the cable, and finally it was detected by Sony. It will reset your device to factory settings though.
Click to expand...
Click to collapse
How did it
How Catch 4 buttons simultaneously
Please reply to the importance of
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
zergmac023 said:
Im in the same scenario.. I tried all the procedures here but i failed.. I noticed that when i connect it, it disconnects after a while along with blinking of led light then reconnect again. And my PC detects it as unknown device.. I tried to install ADB driver but it also fails. Please help me.. Thanks. Sorry about my English
Click to expand...
Click to collapse
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
(
TacoNikky said:
If you flash a different device's rom, it happens. If you replace your motherboard, it will work again.
Click to expand...
Click to collapse
Which probably crying::crying::crying:
yeubeo168 said:
Which probably crying::crying::crying:
Click to expand...
Click to collapse
I have bought motherboard from china http://www.yoybuy.com/en/show/37431065583/ from this seller.
It took 20 days to arrive to Turkey. I have changed my motherboard and my phone is back right now :victory:
It works like a charm. Model number changed, it shows s39h but phone works like old days :good:
A detailed guide :
http://forum.xda-developers.com/sony-xperia-c/general/how-to-install-restore-stock-android-t2832005
It worked!!!!!
GethPrime said:
Fix Xperia C Red Light brick
Are you facing that the red led on your device blinks and there is no other signs of life? Then you are in the correct thread, I faced this issue when flashing a corrupted recovery but then I found out a easy way to fix it without opening the device or sending it in to Sony.
Requirements:
1. The first thing you need to do is to make sure that you have downloaded Sony Update Service and have installed it onto your PC from the link above, if not, do it now.
2. Now launch Sony Update Service and select Xperia C in the list and then press Next.
3. Hold the Volume Up button and plugin microusbcable while doing so, if that doesn't work for you, hold power + volume up and plugin the microusbcable while doing. Keep holding button combination for a few seconds and wait for a green light on your phone, if it appears check on
your PC so that it's detected.
4. Wait while the firmware is being downloaded and reinstalled on your phone and enjoy your working device!
Click to expand...
Click to collapse
It worked for my Xperia M (rooted on JB 4.3) with a locked bootloader which was STUCK on bootloop screen and when I did the whole thing with holding the power and volume up button (after I let the battery die after so many bootloops it did), FINALLY I was able to take it to flashmode, while I had selected from Sony PC Companion to repair my phone, and after 3-4 tries, I DID IT!!! Thank you so much for this thread ( I DEFINITELY pressed the "thanks" button), it really SAVED ME time and money (because I was planning to send it to Sony to fix it and you ALL know how bastards Sony is)!!!! And to all those of you who are DESPERATE to fix their phone (I hope you read this thread), DON'T PANIC, and DON'T GIVE UP!!! It took me 2 days of searching the web, and FINALLY I MADE IT!!! There are ALWAYS solutions to these kinds of problems!!!!
red light
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Need help
same here only red light is blinking,,,i tried doing Power+vol up and Power+vol down and by inserting cable also...it just show a red light when plugged in
i'm also having the same problem....somebody please help!!!!really need to use it
kamran.kerim said:
dear friends please help me. I wanted to install cwm recovery with mobile uncle tools. when I placed recovery.img to phone memory(not in any folder), it didn't find the file, but when in sd card(not in any folder) it succesfully find. I selected and flashed, but the phone shut down and didn't start anymore. yesterday, when plugging to charge the red light under the screen was blinking. but today, it just stays on, not blinking, but after some time, goes off again, and start blinking. when I connect to PC, first it connects, after some time connection is lost and green light passes to red again, after some time it again connects. I tried Sony Update Service and PC Companion, didn't work. Please help...
Click to expand...
Click to collapse
i'm also having the same problem....somebody please help!!!!really need to use it
chauhanjayc said:
Have tried this on my bricked xperia c red led
Few weeks back no success
Logic
If you flash wrong recovery there is no way to boot in any mode
I can say this with 100% confident as I had spent full 3 days and tried every thing...
If u wona check goto custome mod for xperia c thred and get recovery installed
Then try this and share results
All the best
Click to expand...
Click to collapse
Does that mean phone is dead?
choxx said:
Does that mean phone is dead?
Click to expand...
Click to collapse
no all you need stock kernel
you can either google it or download ftf and check all except kernel
done
Im trying to flash a custom rom in my xperia j.
as im a full NEWBIE, i took help of forums on xda.
0. I have flashtool and Android SDK.
1. I downloaded ROM ( X fusion)
2. I downloaded cm10 and gapps.
3. My mobile is already rooted and i unlocked its bootloader.
4. I installed CWM from both mobile and pc.
5. My problem : When i power off and press power + volume up, it wont go in recovery and boots normally.
My phone is stock jellybean.
Well im a real beginner in these things so i wanted to do it to learn it but i need help.
If you need other details, ask me but i really need help.
Try when you see Sony logo rapidly press volume down. How I do it:
Press power button until it vibrates (release power buton)
Rapidly press volume down till it go in CWM.
Good Luck!
Sent from my ST26i using Tapatalk
Dzepar said:
Try when you see Sony logo rapidly press volume down. How I do it:
Press power button until it vibrates (release power buton)
Rapidly press volume down till it go in CWM.
Good Luck!
Sent from my ST26i using Tapatalk
Click to expand...
Click to collapse
I tried it but it simply goes black (blackscreen) and turn off automatically.
thnx for helping me anyway.
Dont i need to try another recovery ?
AdarshJKC98 said:
Im trying to flash a custom rom in my xperia j.
as im a full NEWBIE, i took help of forums on xda.
0. I have flashtool and Android SDK.
1. I downloaded ROM ( X fusion)
2. I downloaded cm10 and gapps.
3. My mobile is already rooted and i unlocked its bootloader.
4. I installed CWM from both mobile and pc.
5. My problem : When i power off and press power + volume up, it wont go in recovery and boots normally.
My phone is stock jellybean.
Well im a real beginner in these things so i wanted to do it to learn it but i need help.
If you need other details, ask me but i really need help.
Click to expand...
Click to collapse
No worries @AdarshJKC98 It's all about Trial & Error, Here's how i install & Use CWM
Ensure Unknown Sources is enabled & Ensure Debugging is also Enabled, You must be rooted, Once you've made sure all of that go ahead and turn your device off, or just take your battery out, Place the USB Sync cable into your PC and go ahead and Boot up Flashtool,Once done so place the Micro USB end into your device and Hold Volume +, If done so correctly a Blue LED will light up, Click the thunderbolt icon on flashtool and select 'Fastboot Mode' And then click on 'Select Kernal To Flash' once done so find the Boot.img i have given you (Link provided below) Once the kernal has been flashed unplug the micro usb cable and go ahead and power on your device
How do i open up CWM on my device
It's simple once you have powered on your device a Purple LED on the Illumination bar Should illuminate keep pressing Volume + or Volume - Either should do the trick, the LED Should then light up Blue, Once done go ahead and use the steps provided to flash your ROM
http://uppit.com/voezk2z644pw/boot.img
Hope this helped ;3
Thnx so much dude, it works
Another small problem !
I entered recovery mode, i wiped cache and tried to install cm10, but it said installation aborted.
So i installed X Fusion directly and rebooted my phone.
But now it lights up, give the purple light which turns off after some time and remains like this.
what to do ?
Hi,
I don't know what can I do now, perhaps noting. I accidentialy flashed wrong bootloader (from other xperia, not Miro). Now phone seems to be completly bricked, I can't turn it on and my PC does not see any new device after connecting phone to usb. I also tried to remove and insert battery, after this when trying to power on, there is short vibration and nothing more.
Do you have any ideas? Or I simply should to use it as brick, not as phone or put it to my toilet and wash? Thanks.
Can you get in flashmode? Power button down + connect to pc. Flash proper ftf for your phone.
Sent from Xperia M2 D2303
Don't worry, Your phone is not hard bricked. As you mentioned that on starting , phone is vibrating that means there are chances to recover your phone.
1.First go through this guide :Using Flashtool for Xperia devices
2.Download your current stock firmware . Visit this: Miro all official firmwares
3.Install proper drivers as mentioned in the above 1.flashtool guide.
4.Flash the firmware for your phone , according to the above 1. Flastool guide.
5.Wait untill flashing completes. start your device when you are told to do so.
Good luck :good:
Dzepar said:
Can you get in flashmode? Power button down + connect to pc. Flash proper ftf for your phone.
Sent from Xperia M2 D2303
Click to expand...
Click to collapse
It seems I can't. I already tried this, but nothing happens. As far as I know, there should be blue led after connect. But nothing happens and PC can't see any new device.
giaur said:
It seems I can't. I already tried this, but nothing happens. As far as I know, there should be blue led after connect. But nothing happens and PC can't see any new device.
Click to expand...
Click to collapse
You should see green light. Try this :
Pull out battery, hold power button for 10 seconds without battery. Reinstall battery, hold volume button - and connect to usb. Then follow steps that prateek.invasion gave you.
The point is you can flash ftf and restore your phone.
Good luck.
Sent from Xperia M2 D2303
Thanks, I will try. Batteery is not charging, so I need to do this quick, it was not fully charged.
Unfortunatly, I can't do anything. I tried to connect while Volume down + power pressed. But nothing happens, only led flashing with red color. PC can't see any new device after I connect to usb.
Any ideas?
giaur said:
Unfortunatly, I can't do anything. I tried to connect while Volume down + power pressed. But nothing happens, only led flashing with red color. PC can't see any new device after I connect to usb.
Any ideas?
Click to expand...
Click to collapse
I had the same issue with my xperia e after I unlocked the bootloader and installed CWM, the phone just rebooted itself at boot up. If you have installed CWM I suggest you to install a custom rom and a new kernel. That worked for me . Or ofc, if you have warranty you can send it to them. They won't be able to tell if you installed another rom since the pc doesn't recognize the phone.
I don't have cwm... trying to connect to computer with volume down pressed. After this led starts flashing red and computer can't see any device connected
Seems there is no any recovery or I can't put it to recovery mode.
Hi. My device is hardbricked. I see no lights while charging. Flashtool doesn't see my device.how can i fix this?
Edit:Easily fixed it.I plugged my device into the computer.I entered platform-tools and flashed boot.img.I saw "waiting for device" And i pressed volume up and power buttons. Suddenly boot flashed and i recovered my phone
You are very unlikely to have hard bricked it unless you have unlocked the boot and flashed something wrong.
If you did this please help us help you by telling us what you did just before this happened.
Also, just leave the phone on charge (Wall charger) for 24 hours and then see what happens.
In the mean time read this
solution for no LEDs no response no fastboot devices.
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Fastboot remote command not allowed SOLVED
stevenmanzano said:
Take two rubberbands one to hold down the power button and one to hold down the volume up button on Xperia Z3 dual. I spent a lot of time figuring this out. Alter a few minutes the phone just booted up from the dead. It worked for me 3 times. Now if someone can tell me how to fix the fastboot remote command not allowed error I'll be happy.
Click to expand...
Click to collapse
Hello
I had the same problem with REMOTE COMMAND NOT ALLOWED till i managed to solve it.
1st thing you need to clean that ANDROID folder you made on C: drive.Install all from the begining including flashtool.Boot windows to install unsigned drivers.In the flash tool folder youll find the driver downloader,just enable usb debugging and choose Mass Storage not MTP .; You have 4 options usb debug on/off and usb connectivity MTP or Mas Storage ;with every version selected connect and disconnect from pc with flashtool running.
When you use Fastboot start the flashtool and close it if it cant kill ADB (that assuming you succeeded in installing drivers).
Good Luck
Please tell me D6603 testpoint
bgbgtbvan said:
Please tell me D6603 testpoint
Click to expand...
Click to collapse
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
john abruzzi said:
you must read this
http://forum.xda-developers.com/showthread.php?t=2646405&page=54
Click to expand...
Click to collapse
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
mihir762000 said:
i have an xperia e3 d2212 stuck pon sony logo....bootloader is unlocked....i m able to enter fastboot so i flashed kernel.sin and system.sin after extracting from stock ftf but it didnt workwed...also,,i m not able to enter flash mode as the flash tool doesnt detects it in flashmode...but when i press power button and volume down the green led lights up...i have reinstalled flashtool many times and also reinstalled the drivers many times...any fix for this??
Click to expand...
Click to collapse
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Omario-242 said:
Try a different driver package from another download source and use another usb on your pc.
Maybe it works. If your device can enter flash mode it definitely can be recovered.
Click to expand...
Click to collapse
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
mihir762000 said:
first of all my phone cant enter flashmode..(just the green light lits up)..secondly,,i have tried to reinstall drivers many times and i have tried to flash the system.sin and kernel.sin of 3 diffrent ftf rom for xperia e3 dual....is there any other solution..???
Click to expand...
Click to collapse
The green led indicates flash mode so the problem is probably on your PC not detecting it properly. Does it show up in the system manager of windows if you plug it in at all? (Like a new device/android with a yellow triangle)
You could also try to fastboot a recovery and flashing a ROM from there. Not sure if it works but that's what I would try.
i m not even able to fastboot a recovery ...tried twrp and cwm both of them...
Me too
in my phone after charging 24h, only the red LED blinks, this is not normal any suggestions?
--------------edit
ok another week and still nothing
maybe I'll describe the problem:
I wanted to upload clean soft 5.1.1 and flash it
after the phone turned off it's start in recovery i used zip with SU and the phone turned off with no respond i try too reset (vol- + vol+ + power) but no reaction
there were no three vib
so I found that you have to reset the button under the sd flip
after this treatment you already know the charging of 3 days and only the red LED blinks
So any suggestions??
|
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
ibo90p said:
I‘m having the same problem, I can’t open my Xperia Z3. I tried with holding on/off button, holding volume up and on/off button, holding volume down and on/off button. When I connect it to PC, nothings happen. No vibrates, no led on, no screen on. What should I do?
Click to expand...
Click to collapse
Like you I have a Xperia Z3 mines the 6633 variant.. Signs were showing it to be hard bricked, for example:
No led charge indication!
No power led!
No fastboot leds!
No USB detection sound when plugging into windows.
Literally a Z3 that was essentially a glass brick I bought off ebay for £6.50 GBP for spares/repair.
Since I had a bricked device, I had nothing to loose.
I applied heat to the rear glass with a hair drier & removed the panel, I removed the battery ribbon cable & plugged in via USB only to find the phone would show LEDs so put it on charge.
The Z3 now goes into flash mode, so then re-flashed a stock ROM from flashtool. I did a apps log & user data wipe, cust reset & fota reset.
To date I have no idea why the phone would not take a charge before or even detect via USB, though Id say give this method a go, you may be surprised!!
Good luck
Hello everybody!
I recently wanted to use a custom rom..
So I Flashed the stock firmware the .291 build. after that I wanted to flash twrp recovery.
So I downgraded the kernel to ,575 then flashed the recovery file, and from the recovery I flashed the Existenz rom (.291 based).
Then I rebooted the device,, Unfortunately I got a boot loop on SONY logo.
So I reflashed the stock firmware (.291) throw flashtool. but flash didn't complete,,, and I got boot loop again.
after that I DON'T KNOW why I flashed the .575 kernel.. Flash completed,, phone turned off
then it's COMPLETELY DEAD.. no signs of life
I tried every power- volume combinations, but I got no vibrations nor leds. and the charging sign doesn't appear when connecting the device to a power supply.
I only hear the connection sound when I connect the device to the computer and press volume down + power button for 10 secs, but it shows nothing on computer!
Any help would be appreciated
Your best bet if it shows no sign of life is to charge for a few hours to make sure it has enough battery.
Hopefully the red light comes on at some point. Either way try leaving it plugged in for a few hours.
Then you can try flashing again.
Ensure all the drivers are properly installed for flashtool.
Ensure you have the correct ftf for your device!
Start flash mode for a full .291 ftf and plug the phone in while holding down the volume down button as normal.
Try this repeatedly until you get a connection.
Alternatively you can wrap a very tight rubber band around the volume down key and connect it while flashtool is in flashmode.
If you're lucky a connection will be made and flashtool will have time to flash the firmware.
Persistence is key here. Many times a brick can be saved but it can take a long time.
Good luck and I hope it works
keep it on charge overnight.flash again when led turns on