Hello Everyone,
My moto g phone suddenly started giving errors saying "unfortunately "xxxxx" not working. xxxx is like google play and many more system services. I cannot do anything as it gives the error continuously.
I was trying to factory reset the mobile and I got the error of "boot up failed". I searched for this and found out that I need to go for custom recovery(I'm new to this) to avoid this error and get my phone back to normal.
I found that I need to unlock boot loader to for custom recovery. After trying and searching a lot I managed to do that finally with the help of a thread in this forum.
From that time I tried with many img files like TWRP, CWM and philz. But, still I could not manage to get my phone back to work.
Last 3 days I was fully in to this searching and finding solution and finally thought to write here(I'm not feeling to give up on this). I can provide you with any information needed.
I read in some guidance of CWM recovery that I need to get CWM model to process further after the below command.
Code:
fastboot flash recovery recoveryimage.img
Instead my screen stays with the below content for whatever .img file I pass for the above command
"Android system recovery <3e>
LXB22. 46-28. 1"
Appreciate any help or support on this to get my phone back to work. Thanks in advance
Nazneen said:
Hello Everyone,
My moto g phone suddenly started giving errors saying "unfortunately "xxxxx" not working. xxxx is like google play and many more system services. I cannot do anything as it gives the error continuously.
I was trying to factory reset the mobile and I got the error of "boot up failed". I searched for this and found out that I need to go for custom recovery(I'm new to this) to avoid this error and get my phone back to normal.
I found that I need to unlock boot loader to for custom recovery. After trying and searching a lot I managed to do that finally with the help of a thread in this forum.
From that time I tried with many img files like TWRP, CWM and philz. But, still I could not manage to get my phone back to work.
Last 3 days I was fully in to this searching and finding solution and finally thought to write here(I'm not feeling to give up on this). I can provide you with any information needed.
I read in some guidance of CWM recovery that I need to get CWM model to process further after the below command.
Code:
fastboot flash recovery recoveryimage.img
Instead my screen stays with the below content for whatever .img file I pass for the above command
"Android system recovery
LXB22. 46-28. 1"
Appreciate any help or support on this to get my phone back to work. Thanks in advance
Click to expand...
Click to collapse
Rename the twrp or cwrecovery as recovery and copy to adb folder. Fastboot command is
fastboot flash recovery recovery.img, (not fastboot flash recovery recovery image .img)
pradeeppk said:
Rename the twrp or cwrecovery as recovery and copy to adb folder. Fastboot command is
fastboot flash recovery recovery.img, (not fastboot flash recovery recovery image .img)
Click to expand...
Click to collapse
it is not "recoveryimage". I just used it for this question. I tried with many files. So, I gave the name of the file and used the command and I got the success message also in CLI saying "Okay" and finished. But no file made any difference to device.
I had a pass code to unlock my screen. Two times I was able to get the screen (Other times it become dark after loading M) and it required the authentication code I gave to enter unlock screen. and I was filled with errors showing continuously "unfortunately not loaded 'system files' ". I suspect that whether the flash worked properly because it was asking for the screen unlock code.
Related
HOX+
4.2.2 sense 5
Unlocked with HTCdev
I have followed ALL the steps from 'Lucky Thirteen', http://forum.xda-developers.com/showthread.php?t=2213910, but can`t get TWRP to install.
Everything goes fine until I use ``fastboot flash recovery TWRPrecovery.img`` command.
The laptop finds the phone because I`ve got ``fastboot usb`` showing on phone screen.
When I type the above fastboot command the message I get is ``error: cannot load ``TWRPrecovery.img`` : unknown error
I`ve spent hours on here trying to find solution... I´ve tried running command in the ``platform tools`` folder where the file is, tried downloading the TWRP file again, tried renaming without .img as suggested, EVERY suggestion I can find. Still won`t install.
Please help, phone still works OK, just can`t get a recovery installed.
Thanks
10rdan said:
HOX+
4.2.2 sense 5
Unlocked with HTCdev
I have followed ALL the steps from 'Lucky Thirteen', http://forum.xda-developers.com/showthread.php?t=2213910, but can`t get TWRP to install.
Everything goes fine until I use ``fastboot flash recovery TWRPrecovery.img`` command.
The laptop finds the phone because I`ve got ``fastboot usb`` showing on phone screen.
When I type the above fastboot command the message I get is ``error: cannot load ``TWRPrecovery.img`` : unknown error
I`ve spent hours on here trying to find solution... I´ve tried running command in the ``platform tools`` folder where the file is, tried downloading the TWRP file again, tried renaming without .img as suggested, EVERY suggestion I can find. Still won`t install.
Please help, phone still works OK, just can`t get a recovery installed.
Thanks
Click to expand...
Click to collapse
Further to my OP I`ve since been able to install TWRP through Hasoon2000`s ``all in one tool```.
Could the problem be something to do with ´´fastboot commands`` ?
If so, am I likely to have problems when I try to flash a boot.img with commands ?
Thanks
Hey,
I'm new to all of this so I really don't know what I'm doing wrong.
I got the normal Moto G running on 4.4.4, unlocked bootloader and rooted.
I've read that if no system files are changed I can just normally update the phone. So I flashed stock recovery (I had CWM before) using MotoTool AiO. But when I want to enter recovery it just gives me the "No Command." screen.
Only other thing I have different is, that I deleted some preinstalled Google and Motorola apps.
When I try to update the phone it just reboots after about 10 seconds telling me the update failed. (I always have to download the update again.)
I hope you guys can help me get to 5.0.2.
Thanks
You need certain Motorola Apps on your phone before the OTA update will work. Also, it's best to be unrooted.
Is there a way to restore the Motorola Apps? With the app i deleted them I can't, because I deleted them completely. (I didn't thought I would need them again.)
I'm not sure if you can find the proper APKs.
It may be easier to just flash back to stock and take the OTA update.
Okay, so I tried to get back a custom recovery so I can flash 4.4.4, but the problem is I still only get the no command screen when entering the recovery.
First I tried flashing CWM with the MotoTool AiO, but I still couldn't enter recovery, so I tried Philz Recovery, but I got the same problem there.
How the hell can I get a recovery, so I can flash 4.4.4?
You need to flash a completely stock ROM, including recovery.
You should download the stock 4.4.4 ROM for your phone and manually flash each partition using fastboot or mfasboot commands.
I tried it with help of this thread.
But it always says i can't find the command mfastboot and with the command fastboot it tells me it can't find the files and when I'm entering the folder it says it can't find the command. And even if I move the extracted files to the same folder (Where the fastboot.exe is) it tells me the files can't be found...
Like I said I'm new to all of this and little more detailed help would be appreciated
PS:
I still got the same .zip with the stock 4.4.4 I used to flash the first time (After that I deleted the system apps)
And in this .zip is an app folder with all the apks, so is there a fast way to just reinstall all of them?
Enable USB debugging and use the Moto AIO tool's Utilities tab to flash APKs to your phone.
http://forum.xda-developers.com/showthread.php?t=2635706
In MotoTool when I'm in fastboot it tells me device not found (Minimal ADB and Fastboot can find my device, and yestery MotoTool could find it, too. USB-Debugging is active.) and when the phone is normally stared in the cmd window it tells me [failed] ... (Can't read the rest, because the window closes instantly), but MotoTool says the installation worked
You need to be booted into ROM in order to use the APK installer.
When installing an APK, you may be prompted on the phone screen to allow your computer to have access to the phone.
Okay I managed to flash 4.4.4 and then I could update to 5.0.2, thanks for the help.
That's great. Glad I could be of some help.
Purchased an Lg Gpad 7 Wifi tablet (v400) 2 weeks ago. Came with preinstalled Lollipop android so i couldnt install a recovery rom to flash any other custom roms. Downgraded to Kitkat version following the instructions on Xda forums and succesfully installed Twrp. When i installed Cyanogenmod 12.1 through Twrp i got stuck in fastboot screen.
Any suggestions and / or solutions would be greatly appreciated.
I had a similar problem.. Only mine was stuck at the bootloader. Go in TWRP and repair /data and other partitions. My data partition gave me an error since F2FS is a little flaky and some ROMs corrupted it (claimed they supported it). I would recommend erasing the system, cache and data partition if you can't get into TWRP.
The problem is i cant get out of fastboot whatever i try. It says start on bootloader but the tablet just restarts on an empty screen doing nothing.
Hakalai said:
The problem is i cant get out of fastboot whatever i try. It says start on bootloader but the tablet just restarts on an empty screen doing nothing.
Click to expand...
Click to collapse
if you have an sd card, try removing that, then reboot.
if that doesnt work, try entering fastboot command, fastboot continue
Tried without sdcard and i get the same fastboot screen.
How can i give any commands? The only options i have are Restart Bootloader / Restart / Power off. Tried restarting bootloader but i get nothing in return tablet just stays on with nothing on screen.
Hakalai said:
Tried without sdcard and i get the same fastboot screen.
How can i give any commands? The only options i have are Restart Bootloader / Restart / Power off. Tried restarting bootloader but i get nothing in return tablet just stays on with nothing on screen.
Click to expand...
Click to collapse
you said it was stuck on fastboot, if thats the case, install any needed drivers on your pc, connect device to it, open a terminal in the fastboot dir (after you go get fastboot), then try those commands i gave. you could also try, fastboot reboot dont think i mentioned that before.
bweN diorD said:
you said it was stuck on fastboot, if thats the case, install any needed drivers on your pc, connect device to it, open a terminal in the fastboot dir (after you go get fastboot), then try those commands i gave. you could also try, fastboot reboot dont think i mentioned that before.
Click to expand...
Click to collapse
Did as you said but every command i gave gives me an error message in adb terminal. There are new lines in fastboot menu in tablet now. Bottom two are SECURE BOOT - enabled & LOCK STATE - locked.
Hakalai said:
Did as you said but every command i gave gives me an error message in adb terminal. There are new lines in fastboot menu in tablet now. Bottom two are SECURE BOOT - enabled & LOCK STATE - locked.
Click to expand...
Click to collapse
hmm, ok, im guessing it would have said that normally, when not broken. all the command does is try to release it past where its stuck. it doesnt actually flash, lock, unlock, or change anything.
imo, this seems good, because now we know fastboot is working.
i own lg devices, but not your specific device. i would hate to give you some bad advice and make your tablet broken more, but if it were me in this situation, i would try to flash the factory KK firmware you used to downgrade with odin or however you did it. hopefully, that will clean everything up and let it boot properly.
if for whatever reason you cant do that, we could try extracting the factory file, and just flashing recovery and system, those should be the only things that got changed putting on twrp and cm normally.
Sorry, I have the serious proplem wtih my LG pad V400, I rooted it and using <LG Flash Tool 2014> with <V40010c_00.kdz> to downgrate the firmware but their is error then my LG pad stuck in fastboot menu as with just turn off, restart and restart bootloader. if i seclect one one them the tablet just logged again the fastboot menu
it stuck on the fastboot menu and i cannot do nay think with it. I can restart with factory restore mode but when select yes to restore, it will restart and log in fastboot menu again.
I downloaded adb and fastboot program and put in one folder <Minimal ADB and Fastboot> in C:\Program Files (x86)\Minimal ADB and Fastboot
I dont have recovery image so i download file <cm-13.0-20160421-NIGHTLY-v400-recovery.img> form your link to download TWRP file
move it to folder of fastboot programe and changed its name to <recovery.img>
I turn on the tablet and it waited at fastboot menu
when i run the command <fasboot flash recovery recovery.img> and they said some thing wrong like in picture
please help me
After trying for over three hours, reading what seems like all threads on the whole of xda and some other sites... i am ready to eat my phone. Ok, must get myself together :-/ . Here we go.
Specs:
Moto G 4g on dutch carrier (vodafone), XT1039
Situation:
Came from completely stock lollipop system, then succesfully unlocked phone via motorola website using the fastboot proces. Intending to install custom rom, first need a recovery. I am now stuck at this step. When booting i now get a screen "warning bootloader unlocked" before the moto splash begins, this is normal as far as i understand.
Problem:
Unable to boot into recovery. Directly after flashing any recovery (with fastboot) and choosing "recovery" from the bootloader i get the message "boot up failed"
After restarting the phone and choosing "recovery" from the bootloader i get the android on its back picture stating "no command"
Already tried:
installed the android sdk, fastboot and mfastboot.
Am able to send commands to phone with (m)fastboot. Flashing works.
I flashed: openrecovery twrp 2850 xt1032, clockwork 6047 falcon, philz touch 6587 falcon, twrp 2870 falcon m stock, twrp 2801 titan v2 and twrp 2860 xt1032
all give exact same result
"fastboot boot NAME of IMAGE"
"fastboot erase userdata & cache"
"fastboot erase recovery"
did the above things in any imaginable combination
I hope someone has some fresh suggestions for me? Thanks for your time.
Bro as far as I know the recovery is not installed u should install twrp from this thread the one on the official site gave me soft brick
Now about the dead android with no command shows that you are on stock recovery and u have booted into it successfully to go further into stock u have to press power and volume up at the same time (like u lock ur phone) but it won't help in installing anything try the recovery I linked (first format your phone complete data and cache wipe from stock recovery not necessary actually) install it through fastboot command and let me know if it worked (with thanks button) BTW what's ur bl ver
thanks for your fast response faizxy, as stated i already tried the one from that thread (i did not use the identical interpunction to describe it but to be clear it is twrp-2.8.7.0.-falcon_M_STOCK.img)
Where do i find my bootloader version? It is the one that came with the device, factory issue...
Some extra info, that might anwser faiz' question: when i boot the bootloader it shows:
"AP Fastboot Flash Mode (S) 41.1A (sha-80481ae, 2015-04-10 14:30:28)
Hope you guys will forgive me for bumping a bit soon, but I really hope some one has a solution! Tomorrow I have time to tinker some more
Have you tried at least one recovery that is actually for your phone (peregrine)?
_that said:
Have you tried at least one recovery that is actually for your phone (peregrine)?
Click to expand...
Click to collapse
Ah. I guess not. Did not know that there where recovery's specifically for the peregrine/xt1039. I searched for "moto g" but apparently is wrong model. DOH!
Thanks for helping out! My problem is solved.
For future reference; finding working pergerine recovery was quite difficult; most mirrors are down. I found one here: https://wiki.cyanogenmod.org/w/Install_CM_for_peregrine and then under header "installing recovery.." under step 2 the download link (i avoid deeplinking)
This one seems to work for me. Now lets find a nice custom rom!
The ones listed here http://forum.xda-developers.com/moto-g/4g-development/progress-twrp-2-7-1-0-source-t2807585 dont work for me. One gives black screen, the other one shows an unlock slider which is unresponsive.
Hi,
Try this one... With encryption abilities or without, your choice...
http://forum.xda-developers.com/showthread.php?t=2996266
Hi! My old phone is booting into fastboot mode, when I try to boot normally I get a black screen, the "Power off" button appears when I hold the power button. The bootloader is not unlocked and the phone was never rooted. Wiping the user partition does not help. It is visible in fastboot mode and I can enter stock recovery, though trying to adb sideload a stock rom returns an error (footer is wrong; signature verification failed). Trying to fastboot boot twrp or recovery.img doesn't work either. I've ran out of ideas, what should I do to get this phone to work?
Try flashing the stock ROM with fastboot. I'm pretty sure ADB doesn't let you flash onto your phone because using your phone with ADB means that it's still powered on - which can cause some issues. You can also try and unlock your bootloader through fastboot, and then flash a recovery and custom ROM.
Both failed. I attached the errors I recieved.
crepper4454 said:
Both failed. I attached the errors I recieved.
Click to expand...
Click to collapse
Try "fastboot bootloader unlock", maybe. Also: Is there a flashall.bat in the stock ROM folder? If there is: Connect your device while in fastboot, and double-click it.
crepper4454 said:
Both failed. I attached the errors I recieved.
Click to expand...
Click to collapse
Try this maybe. I know you can't wipe through the stock ROM, so, try the command: "fastboot -w". That'll wipe everything off the device.
[INDEX][Osprey][Merlin] Moto G Factory Firmware Images
Disclaimer: I am not responsible for anything that happens as a result of flashing these files. Your destiny is your own. Moto G (3rd Gen) Factory Firmware Images - Provided by Firmware TEAM - Please report broken links. New Mirrors welcome...
forum.xda-developers.com
I can wipe through stock recovery. I did fastboot -w and it cleared the cache and userdata partitions, they were already clean afaik. Typing fastboot bootloader unlock returns unknown command. There are no .bat files in my firmware. I can try downloading one from the site you linked, but I don't know what to do with it if fastboot flash does not work.
crepper4454 said:
I can wipe through stock recovery. I did fastboot -w and it cleared the cache and userdata partitions, they were already clean afaik. Typing fastboot bootloader unlock returns unknown command. There are no .bat files in my firmware. I can try downloading one from the site you linked, but I don't know what to do with it if fastboot flash does not work.
Click to expand...
Click to collapse
Try this: https://forum.xda-developers.com/t/guide-osprey-fastboot-flashing-factory-firmware-images.3187750/
It says there that the "preflash validation failed" error occurs when the firmware being flashed is older than the one already installed. I will try downloading a newer version and flashing it. Will update here.
Update: I have dowloaded a newer rom and tried to flash it. This time got different errors (picture attached, this went for every sparsechunk). I think I know the reason but I do not know how to solve it. This might not be the exact stock rom of this phone so I cannot flash it with a locked bootloader. Could someone help me finding the correct rom or suggest a different solution?
Yooooo. I have the Moto e5 Cruise and so does my wife. We bought them in 2018 from Cricket and last night hers went to emmc failure, also known scientifically as 'no worky' mode.
The phone would only load in fastboot and had tried to use my Moto RSD tool to reflash but the phone would not detect in anything but fastboot mode.. Here's where it gets interesting....
There is a piece of software called the Lenovo (which now owns Moto) Rescue and Smart Assistant that can reflash your phone back to factory, no matter your sub-variant (cricket, metro, etc). Without having a fresh backup on hand, you're going to be beholden to the last cloud sync or manual backup you have because all data will be wiped in the below process.
BTW: Just run the assistant as it seems to be the easiest 'back-to-stock/working' tool I can find. Going to fastboot alone yielded weird errors since i didn't have the unlock code for the 'fastboot oem unlock [code goes here]' command.
**RESTORATION PROCESS**
This will apply to multiple Lenovo/Moto Mobility devices. Unknown at this time how many have been impacted by this seemingly pre-planned failure on Lenovo's part.
If your phone is stuck in fastboot mode where MTK download mode does not load, nor does adb, follow these simple steps:
(NOTE: BACKUP YOUR FILES IF POSSIBLE)
1. Click the link above to be directed to the Lenovo software download page and run the installer on your PC (Sorry Mac users :'().
2. The software, once installed, will require you to sign up for OR link a google, fb, g+, etc account to it for purposes of creating a Lenovo ID. Once signed in, click on 'Rescue Now'.
3. With your phone in fastboot mode, allow the software to download the firmware for your phone.
4. Once the firmware has finished downloading and validating, click on 'Rescue Now' once again. Your phone will begin the reflashing process.
That... actually worked. The program found the required ROM and flashing went without problems. Thank you very much @kmt5150 .
crepper4454 said:
That... actually worked. The program found the required ROM and flashing went without problems. Thank you very much @kmt5150 .
Click to expand...
Click to collapse
No problemo! Glad it worked!