Hi, I have a big problem with my new Phone Feiteng H7100! After I flashed the ROM (from needrom), nothing happens on the phone! Everything went as described until the green circle. Nothing now … when connected to the PC appears a USB / network device name: Alcatel Single RNDIS interface, nothing more happens.
Can someone help me here? Please
jemmars
Hello everyone,
can anyone help me here really? I've also, quite diligently search through the forums for possible solutions, but I have not found anything. Please, please help me with my phone ... where I still have birthday ... your help I would be today's greatest gift!
Did you tried to reflash with another ROM?
Maybe this will help you: http://forum.xda-developers.com/showthread.php?t=2186116
Please post your experience.
hi, can anyone help me, i have a feiteng h7100, totally bricked, not turn it on, the computer dont recognize, is a dead phone, i flash it with sp flashtool first time says ok, but no turn it on, so i flash it again, in the middle of flashing says error and the cpu dont recognize any more my phone, any ideas..
never flash DSP_BL and preloader. as long as the device is recognized on your PC, its not "dead" othewise you can try the "testpoint" methode, but not all motherboards have one.
Hello all, It's been awhile since I've been on.... A big while But things have changed a lot around and looks great, But on with my question. I have a M horse N9000W MTK6572, And recently tried a sys file restore using titanium backup and the process froze with a error stating that me deviceID had changed, Then the phone proceeded to reboot, But upon booting up it just stays on the android logo. Before this problem I was able to go into factory recovery as I only had the phone rooted but no custom recovery or firmware, And now no recovery using any button combo. I have asked a few on ebay if there jig or jtag would help but they all say not on the china clone as of yet. So is my phone a cool digital android desktop picture, Or is there a method someone knows
My pc nor mac recognize the device anymore either. Thanks in advance for any info or help
Hi,
I have searched and do not find information that is helpful.
With no recovery and no recognition from the computer, I'm afraid this is a hard brick.
Sorry, I know it is not what you wanted to hear. - support for almost any clone device is scarce at best.
Hello Peeps.
In an attempt to update my rooted Yu yureka from 4.4 MiUi to cyanogen 12 official from fastboot , however the update completed successfully , the device got bricked and never turned on after that .
Nothing works , the phone isnt turning on , no fastboot , not even the light on the led is turning on when i connect it to charging or with PC . The PC isnt recognising if any device is connected to it when i connect my phone to my pc . There is hope with qualcomm emergency flash tool but for that my device needs to be connected to my pc with a port, which is not happening here .
Any help in any direction is highly appreciated. Thanks.
Edit: Yu Yureka aftersales is **** . No one responds to calls , no one replies to mails .There are no service centers. Nothing . Its a dead end here. :crying:
Hi, thank you for using XDA Assist. I found this which sounds exactly what you need, http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040
Good luck!
Thread closed.
Hi
I updated my Phone today using an SD card from the zte website. All was going well and then the screen went off and now I can't start the phone. I have tried a hard reset but it's dead!
Any ideas? Gutted as it's almost new!
Please help if you can.
Cheers
adamfoulkes said:
Hi
I updated my Phone today using an SD card from the zte website. All was going well and then the screen went off and now I can't start the phone. I have tried a hard reset but it's dead!
Any ideas? Gutted as it's almost new!
Please help if you can.
Cheers
Click to expand...
Click to collapse
I have the same problem, did you find a solution?
cheers
Hi
I'm in the same situation, someone has a solution
Help
Me 2.
Help pls.
:crying:
Does it turn on but gets stuck while boot or it doesn't turn on at all?
Sent from my GT-S7262 using Tapatalk
Tali099 said:
Does it turn on but gets stuck while boot or it doesn't turn on at all?
Sent from my GT-S7262 using Tapatalk
Click to expand...
Click to collapse
Hi Tali099 and sorry for my terrible English.
No boot log and only black screen.
Absolutely dead !!!
when connected to pc, find the mobile as: qhsusb_bulk qualcomm 9008 com5.
I had try to unbrick it but unfortunately i didn't find any way to unbrick the chipset: Qualcomm MSM8939 Snapdragon 615 who have the zte blade s6.
Very deep hard brick. :crying:
Have you any idea how to unbrick it ???
I'm the same situation that you.
gining said:
Hi Tali099 and sorry for my terrible English.
No boot log and only black screen.
Absolutely dead !!!
when connected to pc, find the mobile as: qhsusb_bulk qualcomm 9008 com5.
I had try to unbrick it but unfortunately i didn't find any way to unbrick the chipset: Qualcomm MSM8939 Snapdragon 615 who have the zte blade s6.
Very deep hard brick. :crying:
Have you any idea how to unbrick it ???
Click to expand...
Click to collapse
I'm the same situation that you. I need several files for unbrick our phone but I don't found it. I have follow this tutorial: htcmania.com/showthread.php?t=924041
jjcc1999 said:
I'm the same situation that you. I need several files for unbrick our phone but I don't found it. I have follow this tutorial: htcmania.com/showthread.php?t=924041
Click to expand...
Click to collapse
I tried and this way but the "color" was only finds the com port and nothing else. Searching, I found for the "color" is only for chipset Msm8974 and not for ours chipset msm8939. We must look to find the way for unbrick our chipset (msm8939). unfortunately nothing i found as now.
If I can not do anything in the next few days, i will defamation the ZTE in all forums because our problem started from the ZTE proposal to upgrade our mobile with the new version.
gining said:
I tried and this way but the "color" was only finds the com port and nothing else. Searching, I found for the "color" is only for chipset Msm8974 and not for ours chipset msm8939. We must look to find the way for unbrick our chipset (msm8939). unfortunately nothing i found as now.
If I can not do anything in the next few days, i will defamation the ZTE in all forums because our problem started from the ZTE proposal to upgrade our mobile with the new version.
Click to expand...
Click to collapse
I agree with you because the web does not put any warning that may happen or specification in this regard.
Hi
I updated my Phone today using an SD card from the zte website. All was going well and then the screen went off and now I can't start the phone. I have tried a hard reset but it's dead!
Any ideas? Gutted as it's almost new!
Please help if you can.
Cheers
I have exactly the same situation after an official upgrade via SD card..
Black screen will not power on only shows blue light when connected to a charger or laptop.
I have been waiting for over two weeks now for ZTE to provide a solution, nothing, all I get is we are looking into it..
Terrible service and certainly won't be buying any ZTE again
Guys so we are really dead, there is nothing to be done about this problem ? Is this hard-brick ? Any solution here ????
same here
my phone brick after repartition this dump phone
i forget to search that file first..
Please help me s6 was brick [email protected]
reply from ZTE
Hello,
I have been backwards and forwards with ZTE to get this problem resoved and still not sorted. They did send me some instructions of how to reset the device but it needs a piece of software to be able to do this and ZTE won't give it to me to try it out!!!!
I would upload it on here but it seems I am not allowed to or cannot find out how to do it.
This is so frustating!
I got the same problem (black screen) when after rooting and different experiment I tried to put the original ROM back which I downloaded from needrom. After 3 days of continuous searching, I concluded that I have damaged the eMMC Partition by installing a different firmware that was not suitable for my Europe version of Mobile.
This link was quite helpful to understand the problem.
http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040
To solve this problem first I need the 8939_msimage.mbn of Qualcomm 615 and related files. The other option is to use the service ROM and ZTE TOOL STUDIO, I am unable to find this ROM and other files to repair bootloader. If someone with working ZTE blade s6 or other Qualcomm 615 chipset phone can provide this, it would be really helpful.
Following files are required at least from a Qualcomm 615 MSM8939 Chipset.
8939_msimage.mbn
MPRG8939.mbn
patch0.xml
sahara.xml
rawprogram0.xml
Hello all, I have the same problem with my phone except that when it boot , it freezes on " ZTE screen" . What can I do ?
magicfab38 said:
Hello all, I have the same problem with my phone except that when it boot , it freezes on " ZTE screen" . What can I do ?
Click to expand...
Click to collapse
You can enter recovery mode Power On pressing volume up key.
Try "wipe cache partion" at first and if S6 still doesn't boot up, try next "wipe data/factory reset".
If both measures doesn't work, your system has damage from unknown reason.What change did you it?
I have the same problem
:crying:
adamfoulkes said:
Hi
I updated my Phone today using an SD card from the zte website. All was going well and then the screen went off and now I can't start the phone. I have tried a hard reset but it's dead!
Any ideas? Gutted as it's almost new!
Please help if you can.
Cheers
Click to expand...
Click to collapse
adamfoulkes said:
Hi
I updated my Phone today using an SD card from the zte website. All was going well and then the screen went off and now I can't start the phone. I have tried a hard reset but it's dead!
Any ideas? Gutted as it's almost new!
Please help if you can.
Cheers
Click to expand...
Click to collapse
Did you find a solution ?
---------- Post added at 07:32 PM ---------- Previous post was at 07:17 PM ----------
safderali5 said:
I got the same problem (black screen) when after rooting and different experiment I tried to put the original ROM back which I downloaded from needrom. After 3 days of continuous searching, I concluded that I have damaged the eMMC Partition by installing a different firmware that was not suitable for my Europe version of Mobile.
This link was quite helpful to understand the problem.
http://forum.xda-developers.com/yureka/help/question-qualcomm-download-mode-k-t3068040
To solve this problem first I need the 8939_msimage.mbn of Qualcomm 615 and related files. The other option is to use the service ROM and ZTE TOOL STUDIO, I am unable to find this ROM and other files to repair bootloader. If someone with working ZTE blade s6 or other Qualcomm 615 chipset phone can provide this, it would be really helpful.
Following files are required at least from a Qualcomm 615 MSM8939 Chipset.
8939_msimage.mbn
MPRG8939.mbn
patch0.xml
sahara.xml
rawprogram0.xml
Click to expand...
Click to collapse
Hi bro did you find a solution to unbrick the zte blade s6 ?
Hi xda,
So I had a soft bricked Micromax Canvas a290 which boot looped and couldnt access recovery. I flashed it with a stock ROM. Now the phone is hard bricked, and I'm thinking probably because the rom I downloaded had issues. I looked up another stock rom from xdafirmware, and am trying to follow a tutorial on youtube on flashing a hard bricked device.
The issue I have here is this:
The tutorial says the phone is supposed to connect and disconnect every 7-8 seconds (evident by the sound windows makes when usb device is connected and disconnected).
The thing is, when I connect my device windows makes the connected sound, but the device doesnt disonnect. SP flash tool cant flash my phone. I have tried any and every button combination, but they dont seem to help.
I am an tech enthusiast myself, and I have flashed a lot of mtk soft bricked devices before, but I am totally stumped here.
Can anyone help?? Any ideas whats happening? Any help is greatly appreciated. Thank you.
Tiks_Baralous said:
Hi xda,
So I had a soft bricked Micromax Canvas a290 which boot looped and couldnt access recovery. I flashed it with a stock ROM. Now the phone is hard bricked, and I'm thinking probably because the rom I downloaded had issues. I looked up another stock rom from xdafirmware, and am trying to follow a tutorial on youtube on flashing a hard bricked device.
The issue I have here is this:
The tutorial says the phone is supposed to connect and disconnect every 7-8 seconds (evident by the sound windows makes when usb device is connected and disconnected).
The thing is, when I connect my device windows makes the connected sound, but the device doesnt disonnect. SP flash tool cant flash my phone. I have tried any and every button combination, but they dont seem to help.
I am an tech enthusiast myself, and I have flashed a lot of mtk soft bricked devices before, but I am totally stumped here.
Can anyone help?? Any ideas whats happening? Any help is greatly appreciated. Thank you.
Click to expand...
Click to collapse
Greetings and welcome to assist. I can find very little information for your device apart from this thread which may help, can you connect to the device just using fastboot ?
https://forum.xda-developers.com/android/general/tutorial-micromax-canvas-knight-a290-t2872896
Good Luck
Sawdoctor