My Desire s won't charge from the adapter.
After connecting to a PC via HTC's cable nothing happens
I also used another USB cable (from external HDD) to connect with the same results.
Can anyone help please?
Install HTC app for Desire S.
w w w.htc.com/www/SupportDownload.aspx?p_id=391&cat=3&dl_id=1073
I don't say that i can't sync my htc. The USB port is totally dead on the phone! I can't use the htc charger my car charger and any other micro usb cable to charge or connect to a PC.
Today i sent my DS back and waiting for an answer this week.
Also waiting for an explain on the red notification light leaking on the top side of the phone.
This is really wire, and I haven't seen anything like this. Connected to PC with USB cable, DS should jump out some alert to select how to connect your mobile.
If the HW fails, Android has no means of knowing you're attemting to connect anything to the system...this is most likely a HW problem, so sending it back for repair/replacement was the right thing to do
hi, i hve a xoom2, i bought it yesterday; but wht ive noticed is tht the microusb port dont hold well my usb flash ( fat32+16gb), i can charge my tablet but not directly when i plug it in the tablet, i have to pull the edge of the charger up while its in the micros usb port of the tablet so it can charge.
and when i connect it to my laptop, also ihve to move arround the cable data in the microusb port of the tablet .
its a hardware problem? can i replace the microusb port my self? or only moto can do tht?
thkssssssss a lottttttttttttt
So I've had my S7 for around two months now, and all of a sudden fast charging just stopped working. Thought, oh, must be using the wrong cable (have loads of them micro USB cables floating around)
Now I'm certain I'm using the official Samsung fast charge plug and cable that came with the phone, and still no fast charge. When I try to plug into my Windows 10 Desktop or Laptop I have a message that says the device can't be recognized
Phone has already been rooted and flashed with a custom rom. Didn't think that was the issue as it wouldn't even show the mounted storage in TWRP, or identify the phone in ODIN.
Now I've flashed back to the stock rom that I made a backup of when I had the phone, and I still have the same problem!! Can't access internal / external storage using the supplied USB cable and can't fast charge.
I'm thinking the USB port on the device is just knackard.. but really, I've looked after it so well I fail to see how this could happen, unless it's a common fault.
Might just get a wireless fast charger, but do you guys have anything else I can try before giving up on the USB connectivity?
Cheers
try to connect to a different pc, if same it means your usb connector is faulty
Sounds more like the cable is bad tbh, you won't get fast charge from a PC USB port, only from the Samsung charger
But if the device isn't recognised by the PC, and won't fast charge from the charger, the common thing between them is the cable
Possible it's the phone USB port, but more likely the cable is bad
Afaik certain cables can not fast charge either, so chances are the ones you have lying around that are not the official cable can not support it
Genuine Samsung USB cable is white with the USB port symbol on both ends and the phone end has two small ridges to grip when inserting and removing it, should help identify it
Yep I'm using the official cable and fast charger
I'm trying to fast charge via the fast charger and not USB. Only trying USB to access the internal / external storage.
Tried on my desktop and laptop and both have the same issue where my old HTC m8 connects without any issue.
clownstyle said:
where my old HTC m8 connects without any issue.
Click to expand...
Click to collapse
With the same cable?
*Detection* said:
With the same cable?
Click to expand...
Click to collapse
To fast charge I've tried the original Samsung cable with the fast charge plug.
To connect to the PC I've used x3 different cables that all work with my HTC one m8. With all of them I get device not recognised. Already tried installing Samsung switch and reinstalling drivers which didn't work.
clownstyle said:
To fast charge I've tried the original Samsung cable with the fast charge plug.
To connect to the PC I've used x3 different cables that all work with my HTC one m8. With all of them I get device not recognised. Already tried installing Samsung switch and reinstalling drivers which didn't work.
Click to expand...
Click to collapse
I mean for the HTC, does the Samsung fast charge cable work to connect to the PC?
Does sound possible the phones USB port is faulty if you can't get any connection at all to the PC with multiple cables
Try changing the USB mode in developer options
Networking > Select USB configuration
*Detection* said:
I mean for the HTC, does the Samsung fast charge cable work to connect to the PC?
Does sound possible the phones USB port is faulty if you can't get any connection at all to the PC with multiple cables
Try changing the USB mode in developer options
Networking > Select USB configuration
Click to expand...
Click to collapse
Yep the genuine Samsung cable works when connecting the htc to the computer.
I've tried enabling USB debugging and switching between charging, MTP, PTP, RNDIS, Audio Source and Midi.. all of them come back with the windows popup
clownstyle said:
Yep the genuine Samsung cable works when connecting the htc to the computer.
I've tried enabling USB debugging and switching between charging, MTP, PTP, RNDIS, Audio Source and Midi.. all of them come back with the windows popup
Click to expand...
Click to collapse
Unfortunately it is starting to sound like the phone is at fault
Still under warranty? (KNOX 0x0)
*Detection* said:
Unfortunately it is starting to sound like the phone is at fault
Still under warranty? (KNOX 0x0)
Click to expand...
Click to collapse
Unfortunately not. Well it's been rooted and flashed so I guess not.
Ordered a wireless fast charger so hopefully that will see me through and WiFi network for file transfers.
I reckon the USB port will need replacing but I'm not really inclined to do that myself.
Just noticed you said you flashed back to stock using a backup you made
Have you tried stock using ODIN and 100% stock files, using CSC to reset?
My dad has a5 2016 with the same issue, and no warranty. I bought flex + connector , replaced it and still nothing. No fast charge ( it takes cca 4hrs to charge it fully ) and no usb connectivity. I gave up on that
@ClowsTyle
Any luck? I seen your recent post in another thread and it sounds like you tried to replace the USB but that didn't work.
I'm having the exact same issue now. Device suddenly stopped fast charging, Windows does not recognize it when plugged into PC. I ordered a new cable to double check and also tried on different computers. I also tried reinstalling drivers, but nothing has worked.
Hi my is doing the same thing no Fast charge and no pc connection, did anybody find out what happen with yours ?
You have to change power ic s535 for s7 edge.
When usb gets moisture power ic will damage.
I have same problem my phone charging 0-100 6hours but ı install notorious kernel and it takes 3 hours it is better than 6 hours
Same Issue
I've had the same issue for the past 3 weeks now and I've tried everything I know...
1. Tested cable and charger with another S7 and they work fine.
2. Factory Reset.
3. Changed the USB port chip.
4. Turned on "Low Battery Dump".
So far, the issue hasn't changed.
was this issue solved?
I´m having same issues whit my galaxy s7 active, I can not fast charge my phone no matter what cable I use, then noticed that evrytime I plug it to any computer it says the devicescan not be recognized, I´m about to buy a new charging port and install it, but I want to make shure this is not a software related issue.
I´ve tried several cables and several laptops/ pc´s
I´ve factory reseted my device and turned on low battery dump, wiped cache partition, and problem still there...
The charger could be faulty/damaged did you try a different charger?
---------- Post added at 06:43 PM ---------- Previous post was at 06:40 PM ----------
Dial *#08# and select the first option (mtp and another option i am on a custom rom that seems to not have the *#0808# setting
I also have the same issue with my phone the phone charges but not recognize and also tried to change settings on phone and nothing? And my other samsung phone works and nothing wrong with USB tried to install smansung drivers on PC and still same issue.
I tried a different USB and nothing works and different ports on my comp.
My ports works with my other samsung phone so not sure why not with the S7?
Is the USB faulty?
I was connectted my phone to my laptop by USB C cable to use my phone's ethernet. suddenly i heard some crackle and burned smell come from my phone's USB port. I am afraid to use USB cable or charge my phone.
Azkelimecokislem said:
I was connectted my phone to my laptop by USB C cable to use my phone's ethernet. suddenly i heard some crackle and burned smell come from my phone's USB port. I am afraid to use USB cable or charge my phone.
Click to expand...
Click to collapse
Thanks for sharing this with us. But since you're not asking a question here, maybe you should just take your phone to a service center.
hI everyone in regard to otg using Usb and charging tablet at same time, I have a fusion5 tablet and a usb hub the kind with 3 usb hubs and a power in with a micro usb male plug. and a switch for otg or charge. Ive tried using a potentiometer to find the magic resistor value between pin 4 (the id ) and pin 5 ground of the micro plug.
(thought i had it at one point but not sure) as could play a avi file while charging) However now most of the timee either accesses the usb or charges, I can get it to do both , but stops charging after 8 seconds.
Anybody happen to know if a specific resistance value works for both charging and otg.
I have seen another schematic but havent tried it.
It doesn't sound like the micro usb otg cable to me. I built one without a resistor and mine works just fine. Have a look at your usb settings. Some devices require you select your choice: usb otg or charging.
nastiero said:
It doesn't sound like the micro usb otg cable to me. I built one without a resistor and mine works just fine. Have a look at your usb settings. Some devices require you select your choice: usb otg or charging.
Click to expand...
Click to collapse
Thanks How do I look at my usb settings?. I think I may not have the proper resistor setting as will currently provide power to usb and charge at same time for a few seconds then stops charging.. I turn resistance up it will charge , turn it down and will allow access to usb.. i think have to find that magic number inbetween.
jmxda21 said:
Thanks How do I look at my usb settings?. I think I may not have the proper resistor setting as will currently provide power to usb and charge at same time for a few seconds then stops charging.. I turn resistance up it will charge , turn it down and will allow access to usb.. i think have to find that magic number inbetween.
Click to expand...
Click to collapse
Depending on which phone and version of Android you have, the most recent versions of Android have the USB settings under Developers Options.
The USB OTG charging works differently from phone to phone. Sometimes you must plug your charger cable and the USB device you want to connect to into the OTG cable prior to plugging the OTG cable into your phone. This way the phone detects charging and device.
nastiero said:
Depending on which phone and version of Android you have, the most recent versions of Android have the USB settings under Developers Options.
The USB OTG charging works differently from phone to phone. Sometimes you must plug your charger cable and the USB device you want to connect to into the OTG cable prior to plugging the OTG cable into your phone. This way the phone detects charging and device.
Click to expand...
Click to collapse
Yes that is what I have been doing . In developer options under Usb default , no charge option there, only file transfer, USB tEThering, MID, PTP ,and o data transfer
I thanks. However i believe the default USB option is charge as thats what it is when i plug in USB to a powered cable.
. As I said jt works for A short time using USB and charging at same time with resistor between 45K and 68k
then either stops charging and continues usb or keeps charging but gives usb errrors or cant access usb but continues charging.
Fusion5 tablet android 9
Update this works fine with unmodified USB hub or charge power and USB on my LG k32 phone but not on the fusion ta blet.