Related
I just got this screen protector in the mail today. Its really good so far, I would recommend it for everyone. It's not that thick, and it protects against scratches and scuffs. Only thing I don't like is it doesn't fit the whole area. What I mean by that is the black parts outside the screen isn't all covered up. But its still good. Heres the website. Cool thing too is they actually give you 2 screen protectors.
http://www.sgpstore.com/advanced_se...Csid=759c22591b3eb0f2ddda0347bfd9fcc3&x=0&y=0
After having seen all of the issues with the glass screen protectors for this phone, I decided that I needed to try something else in the meantime. While I have a Sakai glass one that I ordered from ebay that is due roughly a month from now, I'm not very hopeful for it working. As a result of all of this and the need for a screen protector ASAP, I went with the Spigen screen protectors that I have seen mentioned on here. Having used PET films in the past, I was expecting a huge hassle. Bubbles, cheap feeling etc. Turns out, these worked REALLY damn well, to my complete surprise.
Installation:
Installation was quite easy, much easier than the older thin film screen protectors that I remember. You simply clean the surface of the phone, following the instructions. Place the tabs on the screen protector to help you position it. Then carefully position it properly keeping an eye on the edges and the sensors. It adheres to the screen very much like a glass screen protector does. There are a few small bubbles here and there, but they squeegee right out. I ended up with two permanent bubbles (one by the light sensor and one near the edge). Neither were the fault of the screen protector, both were caused by me rushing and nicking the surface of the screen protector when squeegee-ing the bubbles out. I think I could easily get it on there next time with zero bubbles. Way less hassle than any other attempt I have had with a film screen protector. One complaint I have is that they only included one alcohol wipe (everything else is in multiples), I don't know if I just got unlucky or they aren't thinking. Anyways, I have access to many solvents at work. No big deal for me.
Result:
How does it feel? A bit more plasticy than the usual glass screen protector but otherwise surprisingly nice. It adheres to the curves perfectly with no major bubbles, clarity-wise it is crystal clear. I honestly can't tell it is there. It adheres nicely to the curves of the display without any gaps (other than my nicks at the edge). My Otterbox Commuter case fits right over the top of it with ZERO problems. I was expecting these to be a stop-gap measure until the better glass ones come out but honestly I don't see anything wrong with these as is and would be just fine using these alone. I am not sure about longevity as I just installed it but so far I am actually surprisingly happy with it, especially for the cost. If you are on the fence between glass and plastic. Go with these plastic screen protectors for now and let the manufacturers work out the difficulties of the glass ones. Then you can decide later if you really want the glass one for you phone.
Link:
https://www.amazon.com/gp/product/B01B1GQDGG/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
it will get scratched to **** within 2 weeks don't worry. Then you'll have to use another of the 3 that came with it.
Agreed with everything that OP posted, and agreed with the person above. Mine got scratched within a day but I got over it.
I installed one only because I tried three different Temper glass ones and none sealed correctly. I like it so far installed very good, covers the entire screen. So far so good.
I got a soft screen protector from AliExpress. It's a bit tricky to apply at first but once you get the idea it's not so bad.
The screen protector is really good! It's like silicon , doesn't get scratched easily.
Best part? it's 1.4$ each! What else can you ask for..?
Link:
http://www.aliexpress.com/item/For-LG-G5-Full-Coverage-Soft-Screen-Protector-Guard-Film-for-LG-G5/32618522429.html?spm=2114.13010608.0.54.iHJztH
Here:
Yup good screen protector but it does scuff, so is it perfect no, but one of the better non temper glass protector
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Jonathan-H said:
I just tried and failed to apply all three. I can't be doing with bubbles or marks on the screen, and who in their right mind decided to put adhesive on a screen protector.
First one too many bubbles, second one, dust, bubbles and scratches, third one, same.
Add to the fact it feels like a ZAGG invisible shield, rubbery rather than glassy.. I will keep it naked from now on.
I have an Xtreme skin skin to install, wish me luck, i'll bloody well need it haha.
Click to expand...
Click to collapse
I got the dark oak Xtremeskin!
I've put on a tempered glass before, it was kinda bad, lost saturation and brightness, and i got a clear case from spigen, but the case's lips protudes to the center so much that it started to push the screen protectir out!, I eventually removed the tempered glass... Not usre which screen protector to apply on with the spigen case :/
The Spigen Crystal Clear is too thin in my opinion - I killed it within a week. My old Spigen Steinheil Ultra on the S4 was way better. Purchased a CrocFol Premium instead.
Yup I have to change my opinion as well, used it for a bit, scuffed easily, stays clear without the rainbow effect. I had a few defects in my screen protectors, changed them out. Using the otterbox Defender case for now.
1$ tempered glass (rectangular) from AliExpress are perfect of you dont care leaving the top curved part unprotected. No bubbles, no rainbows, no effect on colors\contrast\clarity.
So I had the similar Artech 21 case for the Note 5 which is the same people that make the Armadillo Tek case for the Note 9.
I liked the Note 5 case and built in screen protector but I was wondering about the built in screen protector on the Note 9 case since it's curved so the material is different.
Also, has anyone removed the built in screen protector and if so does it cause the phone to be loose in the case?
I'm waiting for more reviews on this case before ordering off Amazon but it looks decent.
How is the protection of the case compared to the Samsung rugged cover
interested in feedback as well.
Blues fan said:
So I had the similar Artech 21 case for the Note 5 which is the same people that make the Armadillo Tek case for the Note 9.
I liked the Note 5 case and built in screen protector but I was wondering about the built in screen protector on the Note 9 case since it's curved so the material is different.
Also, has anyone removed the built in screen protector and if so does it cause the phone to be loose in the case?
I'm waiting for more reviews on this case before ordering off Amazon but it looks decent.
How is the protection of the case compared to the Samsung rugged cover
Click to expand...
Click to collapse
The case is solid. The screen protector left much to be desired. I removed it easily and the phone still stays solidly in place. It is more protective than the Samsung rugged case but not as slim. I'd feel comfortable dropping it in the armadillo case. Here's a video review I did of it:
https://www.youtube.com/watch?v=px2roiwe7UM
I have the case as well, I honestly bought like 4 different cases for the Note 9 before I got it, and one of them being the Spigen ToughArmor case and the Armadillotek. I have to say just for protection overall, the AT is way better than the Spigen case. It protects the phone more while not being that bulky, it is slightly less comfortable to hold because of the weird design and kickstand on the back, but its way better than essentially the toothpick that's on the back of Spigen cases.
The case itself covers the front of the phone a lot better than the Spigen as well (edges are raised slightly higher, the case actually covers some of the exposed glass around the sensors and the chin of the phone). It is slightly more expensive, but I'd recommend it to anyone who's scared of dropping their phone tbh.
I didn't bother with the built in screen protector, I don't like plastic screen protectors because they're too scratch prone, but it was easy to just punch it out, remove the adhesive, and just use your own glass screen protector.
It's near perfect, but if the back didn't feel a little weird, I'd say it's a perfect case
Yea, the built in screen protectors in these cases like the Armadillo, Supcase, Youmaker, etc. don't seem really good due to the curved screen. When the galaxy had a flat screen it was fine because a different material was used.
The only think I don't like at least on the Supcase, others as well as the Artech 21 case was the port covers. Unlike the Otterbox Defender it seems over time they can crack.
Right now I use the Defender mostly due to the extra big lip and better side protection.
I might go on a case binge and order the Supcase and Youmaker though but I will for sure the punch out the screen protector. I keep nothing in my phone pocket and the lips on these cases are enough I don't have to worry about contact with the ground.
The Samsung rugged case is a very well built case though. Except I prefer something with more girth like the Otterbox Defender. The Defender makes it easier to grip and use spen.
I'm enjoying it so far. I can type and swype jus like normal, no aggravating mistypes and dead spots. Jus yesterday I was noticing that my screen had some fine scratches on it, and I might keep this plastic protector on for a while. As far as the case, I have used some similar in the past and it is very protective. I also like how it connects together. I don't have to worry if it will come apart.
grmcrkrs said:
I'm enjoying it so far. I can type and swype jus like normal, no aggravating mistypes and dead spots. Jus yesterday I was noticing that my screen had some fine scratches on it, and I might keep this plastic protector on for a while. As far as the case, I have used some similar in the past and it is very protective. I also like how it connects together. I don't have to worry if it will come apart.
Click to expand...
Click to collapse
Those marks might not be scratches but just from the spen. Just like on a naked screen you will notice the spen leaves marks. All you need to do is just wipe it off.
Either way, the screen protectors suck on these cases. Better off just popping them off and go bare. Just don't put keys in your pocket with the phone.
I ripped off the plastic screen protector and installed an edge-to-edge tempered glass one. It works great on me.
I had to rip the plastic cover off as well.
grmcrkrs said:
I had to rip the plastic cover off as well.
Click to expand...
Click to collapse
So the built in screen protector isn't really that good?
It does protect the screen. But the edges don't hug the screen super tight, about 1 centimeter around or over the curve. This slight space causes me to have to press a little harder than I'm used to, and that causes mistypes and unresponsive touch, about 1/10 times when I touch that space.
grmcrkrs said:
It does protect the screen. But the edges don't hug the screen super tight, about 1 centimeter around or over the curve. This slight space causes me to have to press a little harder than I'm used to, and that causes mistypes and unresponsive touch, about 1/10 times when I touch that space.
Click to expand...
Click to collapse
did you turn on the 'touch sensitivity' ?
yes, I sure did. Like I say, 99% of the time was fine, but the edges of the screen protector, the tiny part over the curved edge, was slightly raised with an air gap. So it caused mistypes.
jinshanghaiaraol said:
I ripped off the plastic screen protector and installed an edge-to-edge tempered glass one. It works great on me.
Click to expand...
Click to collapse
I did too, I have the white glass dome. Hehe
Majin101 said:
I did too, I have the white glass dome. Hehe
Click to expand...
Click to collapse
The whitestone glass screen protector is great.
all screen protector sucks! Only use Whitestone tempered glass screen protector for noW
This case is a monster when you use the glass SP with it !
I have a armadillo tek case and i think it sucks
The screen protector is a piece of **** and they told me up front to rip it off, and also the headphone jack and charger jack covers wont stay closed and they told me tough **** to that one.
Also the charger port is too small to allow the samsung usb on the go port to be inserted
I've been using the Armadillotek case for my Note 9 for a couple weeks now. I really like the case overall but decided to switch back to my Defender for now.
First, the built in screen protector doesn't quit sit totally flush because of teh curved glass. This causes it to have a tiny bit of air gap which dust and dirt gets underneath and drives me nuts, plus with the Kickstand it leave the phone exposes a but when you use it allowing dirt to get in there.
Also, the sides of this case are raised which is great! gives more protection but also allows dirt and grime to collect on the sides.
I really like the case and eventually might just rip the protector out. I might try the Poetic Revolution and Supcase Unicorn Beetle out but I'm sure the screen protector will be crappy too and I'll just rip it out.
I can see why Otterbox ditched the built in protector for the curved phones.
They tried it with the S7 Edge. With the S7 edge it fit VERY snug to the phone so no dirt got under it BUT screen responsiveness was atrocious with it. Just terrible.
I might order the orange Armadillo because I like the color but for sure will rip the protector out on one of them and save the other for when I want a screen protector in certain situations.
I ripped the screen protector out as well. Very easy to take off and makes it perfect for me.
I ripped off the screen as well, worth it. I have the white glass dome on my phone, gives me protection already.
Thing I don't like about Armadillotek and "tough" cases like them is that too often their designs are so gaudy. That's why I like the Commuter (and even Defender). They're mature-looking. Pretty understated. Low-key, kinds of cases.
Thanks for the information...
I just simply rip off the plastic protector, and install tempered glass one.
Now I can it tough
I like the defender but I hate the holster. I've used the seidio surface holster for years now and it's far superior IMO. Wish I could find a holster like the surface one for the defender.
Disclaimer: No, I don't work for QiMai or the seller on Amazon. I'm just a guy who has been struggling with screen protectors since the S8+, and finally found one I'm 100% satisfied with. So I figured I'd share.
I was using the Cubevit PET screen protector and loved it, but it was a fingerprint magnet, and like all PET screen protectors got pretty scratched up.*Otherwise it's a FANTASTIC screen protector and only $8 for a 3-pack.
I had put a QiMai TPU screen protector on my wife's S9+, and you could barely tell it was there. I have to occasionally pick up her phone and look really close to make sure it's still on there. But since it was TPU I worried about it having that rubbery feel, and the SPen leaving marks.*
Since the QiMai was only $10 for a 2-pack, I decided to give it a try on my Note 9 anyway, and seriously, it's the best screen protector out there. It may not offer the drop protection of a Whitestone Dome, but as far as clarity and feel, there's no equal.*
It is crystal clear. Matter of fact it covers the FF camera and all the sensors, but it causes no distortion or interference. And it's almost as slick as the factory glass. It has no rubbery drag at all. And fingerprints wipe away very easy. And no indents from the SPen, unless you really dig in. Even then they disappear quickly.*
Ringke makes a similar screen protector, as does a few other companies, but I haven't tried them. Here is the link to the QiMai if you all want to try it.*
Galaxy Note 9 Screen Protector, 2-Pack QiMai Case Friendly Easy Install Screen Cover(Not Glass)[New Version]*https://www.amazon.com/dp/B07H2ZW9PG..._q.BfCbVBPDM3J
So far no interference with my cases. I use a Ringke Air, a Speck Grip, and a couple minimal generic TPU cases. So nothing that really comes far over the edge of the screen. I'll be ordering some Goosperry cases soon, but I don't see where they would interfere either.
Installation is easy, but it's also easy to get lint under it. It took me four tries. The first one was 95% perfect except for a bubble from lint in the top right corner. The second one got a bubble for an unknown reason that wouldnt go away. Small bubbles disappear after 24 hours. But this one wouldn't. Otherwise it was almost perfect.
I reached out to the seller and he sent me a free replacement 2-pack. I screwed up the first one, but finally the last one went on perfectly.
I do think I'll try the Ringke version of this screen protector next time, simply because it was a built in lint remover that picks up all lint and dust as you install automatically. But I've got no experience with the Ringke to know if it's as smooth as this one.
If you want a tempered glass screen protector, then go for the Whitestone Dome. But if you like thin, minimal screen protectors that you can't tell is there, then I highly recommend this one.
UPDATE: I accidentally tore my QiMai screen protector, so I used the opportunity to try the Ringke Dual. It's the same exact material and fit as the QiMai. It just as clear, but is slightly easier to install. It seems to be more oleophobic, yet not quote as slick as the QiMai. They are both super smooth to the touch, but the Ringke seems to have just slightly more drag to it.
But I can say I like both screen protectors and you can't go wrong with either one.
Mr. Orange 645 said:
Disclaimer: No, I don't work for QiMai or the seller on Amazon. I'm just a guy who has been struggling with screen protectors since the S8+, and finally found one I'm 100% satisfied with. So I figured I'd share.
I was using the Cubevit PET screen protector and loved it, but it was a fingerprint magnet, and like all PET screen protectors got pretty scratched up.*Otherwise it's a FANTASTIC screen protector and only $8 for a 3-pack.
I had put a QiMai TPU screen protector on my wife's S9+, and you could barely tell it was there. I have to occasionally pick up her phone and look really close to make sure it's still on there. But since it was TPU I worried about it having that rubbery feel, and the SPen leaving marks.*
Since the QiMai was only $10 for a 2-pack, I decided to give it a try on my Note 9 anyway, and seriously, it's the best screen protector out there. It may not offer the drop protection of a Whitestone Dome, but as far as clarity and feel, there's no equal.*
It is crystal clear. Matter of fact it covers the FF camera and all the sensors, but it causes no distortion or interference. And it's almost as slick as the factory glass. It has no rubbery drag at all. And fingerprints wipe away very easy. And no indents from the SPen, unless you really dig in. Even then they disappear quickly.*
Ringke makes a similar screen protector, as does a few other companies, but I haven't tried them. Here is the link to the QiMai if you all want to try it.*
Galaxy Note 9 Screen Protector, 2-Pack QiMai Case Friendly Easy Install Screen Cover(Not Glass)[New Version]*https://www.amazon.com/dp/B07H2ZW9PG..._q.BfCbVBPDM3J
So far no interference with my cases. I use a Ringke Air, a Speck Grip, and a couple minimal generic TPU cases. So nothing that really comes far over the edge of the screen. I'll be ordering some Goosperry cases soon, but I don't see where they would interfere either.
Installation is easy, but it's also easy to get lint under it. It took me four tries. The first one was 95% perfect except for a bubble from lint in the top right corner. The second one got a bubble for an unknown reason that wouldnt go away. Small bubbles disappear after 24 hours. But this one wouldn't. Otherwise it was almost perfect.
I reached out to the seller and he sent me a free replacement 2-pack. I screwed up the first one, but finally the last one went on perfectly.
I do think I'll try the Ringke version of this screen protector next time, simply because it was a built in lint remover that picks up all lint and dust as you install automatically. But I've got no experience with the Ringke to know if it's as smooth as this one.
If you want a tempered glass screen protector, then go for the Whitestone Dome. But if you like thin, minimal screen protectors that you can't tell is there, then I highly recommend this one.
Click to expand...
Click to collapse
Nice, is it just a film protector?
felloffthetruck said:
Nice, is it just a film protector?
Click to expand...
Click to collapse
Yup. Dry install TPU film.
The link is borked, though Was easy to find with search, but still..
does the S-PEN leaves marks on the film after using it for a while ?
6thtry said:
The link is borked, though Was easy to find with search, but still..
Click to expand...
Click to collapse
Sorry about that! Try this link:
Galaxy Note 9 Screen Protector, 2-Pack QiMai Case Friendly Easy Install Screen Cover(Not Glass)[New Version] https://www.amazon.com/dp/B07H2ZW9PG/ref=cm_sw_r_cp_apa_i_43agCbXE0S0MW
emudojo said:
does the S-PEN leaves marks on the film after using it for a while ?
Click to expand...
Click to collapse
I actually covered that in my original post:
Mr. Orange 645 said:
And no indents from the SPen, unless you really dig in. Even then they disappear quickly.*
Click to expand...
Click to collapse
Was just looking at the Ringke and it has no install guide.
I've always hated film protectors but might give this one a try.
Does it peel off easy and clean?
So my first package of tg was a failure. Neither stuck to the screen. Returning to Amazon. My whitestone (which I'm not sure now if I'll end up using now) is still a few days away, so I ordered this to have coverage. It will be here tomorrow.
felloffthetruck said:
Was just looking at the Ringke and it has no install guide.
I've always hated film protectors but might give this one a try.
Does it peel off easy and clean?
Click to expand...
Click to collapse
Yes it peels off easy and clean. No adhesive residue.
I actually JUST switched to the Ringke screen protector. LOL. I put my Note 9 in a sleeve to carry it without a case, and the corner of the screen protector peeled up and tore. So I ordered the Ringke to try it out. I like it just as well as the QiMai. There's some subtle differences. The Ringke is actually easier to install. And even though the QiMai feels just slightly slicker than the Ringke, I think the Ringke is more oleophobic. You honestly can go wrong with either one.
PuffinNugz said:
So my first package of tg was a failure. Neither stuck to the screen. Returning to Amazon. My whitestone (which I'm not sure now if I'll end up using now) is still a few days away, so I ordered this to have coverage. It will be here tomorrow.
Click to expand...
Click to collapse
What did you think of it?
Mr. Orange 645 said:
Yes it peels off easy and clean. No adhesive residue.
I actually JUST switched to the Ringke screen protector. LOL. I put my Note 9 in a sleeve to carry it without a case, and the corner of the screen protector peeled up and tore. So I ordered the Ringke to try it out. I like it just as well as the QiMai. There's some subtle differences. The Ringke is actually easier to install. And even though the QiMai feels just slightly slicker than the Ringke, I think the Ringke is more oleophobic. You honestly can go wrong with either one.
What did you think of it?
Click to expand...
Click to collapse
How well does the dust removal deal work on the Ringke?
felloffthetruck said:
How well does the dust removal deal work on the Ringke?
Click to expand...
Click to collapse
Not that great, actually. I think they could have used a little stronger adhesive, but it's okay. I wound up with one speck of dust on the very edge, but I also used a dust absorber from another screen protector kit to remove any heavy lint and dust.
It turned out about 99.9% perfect, which is the best I can expect from any screen protector. I always end up with some speck of dust or bubble somewhere. It's just so hard without an actual clean room.
I will say the screen protector is absolutely invisible. You have to look very hard to see it. And the more I use it, the slicker it feels.
Just make sure it's straight and aligned before you peel off the backing (tab 2 and 3). I had to readjust mine a few times to get it straight and centered left to right. That is one advantage to this installation method. You can readjust it as much as you want before you actually secure it permanently to the screen.
Mr. Orange 645 said:
Not that great, actually. I think they could have used a little stronger adhesive, but it's okay. I wound up with one speck of dust on the very edge, but I also used a dust absorber from another screen protector kit to remove any heavy lint and dust.
It turned out about 99.9% perfect, which is the best I can expect from any screen protector. I always end up with some speck of dust or bubble somewhere. It's just so hard without an actual clean room.
I will say the screen protector is absolutely invisible. You have to look very hard to see it. And the more I use it, the slicker it feels.
Just make sure it's straight and aligned before you peel off the backing (tab 2 and 3). I had to readjust mine a few times to get it straight and centered left to right. That is one advantage to this installation method. You can readjust it as much as you want before you actually secure it permanently to the screen.
Click to expand...
Click to collapse
Can you post a couple pictures showing this protector on the phone?
felloffthetruck said:
Can you post a couple pictures showing this protector on the phone?
Click to expand...
Click to collapse
Sure. If not today, I'll snag some pics tomorrow.
felloffthetruck said:
Can you post a couple pictures showing this protector on the phone?
Click to expand...
Click to collapse
This is the Ringke screen protector. I didn't get any pics of the QiMai protector.
Those specs are dust ON the screen protector, not under it.
Mr. Orange 645 said:
This is the Ringke screen protector. I didn't get any pics of the QiMai protector.
Click to expand...
Click to collapse
WOW, that looks nice. I'll have to give them a try.
Did you get that result on the first try?
felloffthetruck said:
WOW, that looks nice. I'll have to give them a try.
Did you get that result on the first try?
Click to expand...
Click to collapse
Yes I did. But I cheated a little. I also bought the same screen protector for my Note 8 and installed it first. So I at least had some practice.
Just use as close to a dust free environment as you can. Then clean your screen really well, remove all dust with a dust remover if you have it, then take your time lining up the screen protector. Remember, you can lift it and readjust as many times as you want before you pull tab 2 and secure it permanently.