Database Info

[Q] GT-I9195: Odin failed EXT4 partition error... help fix?

Hello!
I recently got a S4 mini and decided to root so I could have an extended memory using link2sd! Everything was perfect but later the KITKAT update started to roll out, so i decided to go back to stock so I could update my phone... I downloaded a stock Rom from Sammobile and used odin to flash it... It keeps saying that EXT4 failed! So now its stuck in download mode! When I try to root just to see if it fixes anything it makes the Samsung boot sound and then the screen goes black.. I try reflashing the 4.4.2 Rom but it keeps failing!
Here is what ODIN3 3.0.7 says:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNEA_I9195VFRCNE4_I9195XXUCNEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> NON-HLOS.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Please tell me a fix because its stuck in firmware upgrade fail screen!
Also Kies wont detect it and i have installed USB drivers for my phone!
Also please don't say that I shouldn't have rooted and stuff because it is too late for that.
BTW I am going to thank (like) anyone who fixes this!

Yiannis1 said:
Hello!
I recently got a S4 mini and decided to root so I could have an extended memory using link2sd! Everything was perfect but later the KITKAT update started to roll out, so i decided to go back to stock so I could update my phone... I downloaded a stock Rom from Sammobile and used odin to flash it... It keeps saying that EXT4 failed! So now its stuck in download mode! When I try to root just to see if it fixes anything it makes the Samsung boot sound and then the screen goes black.. I try reflashing the 4.4.2 Rom but it keeps failing!
Here is what ODIN3 3.0.7 says:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNEA_I9195VFRCNE4_I9195XXUCNEA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> aboot.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> NON-HLOS.bin
<ID:0/004> cache.img.ext4
<ID:0/004> hidden.img.ext4
<ID:0/004> FAIL! (Ext4)
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Please tell me a fix because its stuck in firmware upgrade fail screen!
Also Kies wont detect it and i have installed USB drivers for my phone!
Also please don't say that I shouldn't have rooted and stuff because it is too late for that.
BTW I am going to thank (like) anyone who fixes this!
Click to expand...
Click to collapse
Try a different ROM. I had the same problem with the NEA one but the NE6 loads OK.

[Q] Soft bricked S6

Hello guys i was going to re flash my phone back to 5.1.1 (used the beta android 6.0) used this one to get 6.0 http://www.sammobile.com/firmwares/download/54860/G920FXXU2COH2_G920FBTU2COH3_BTU/ and downloaded this one http://www.sammobile.com/firmwares/download/61178/G920FXXU3QOKD_G920FNEE3QOKD_NEE/
And i forgot now that it needed to be same numbers or what i should say in odin it says failed heres a dump
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Should i just restart the phone go back to download mode and download this one http://www.sammobile.com/firmwares/download/55165/G920FXXU2COH2_G920FNEE2COH3_NEE/ re add it to Odin and re flash? Or will i do this more worse than it is right now?

Just flash a pit file.. factory reset from recovery ans you're OK

lummujaj said:
Just flash a pit file.. factory reset from recovery ans you're OK
Click to expand...
Click to collapse
Can you guide me abit more about this i re enter the download mode cant i just put in the right
NEE:
PDA G920FXXU2COH2
CSC G920FNEE2COH3
BTU
Product code BTU
PDA G920FXXU2COH2
CSC G920FBTU2COH3
The NEE PDA and CSC is the same as the BTU now and i downloading that NEE version again from sammobile cant i juse put the right NEE in odin and reflash?

Hey again nevermind did an emergency reset from samsung smart switch and now the phone is working

[Q][HELP][GT-P5110]Flashing Firmware PASS but still firmware upgrade problem

helo..
my tablet gt-p5110
cannot enter recovery (pwr+vol+) and download mode (pwr+vol-), but just stuck in "firmware upgrade encountered an issue, please recovery mode in kies & try again",but the device still connect and sync to odin.
I was using a pit file but when started there is an info from Odin that ''pit partition does not exist''.
when flashing use odin 3.07 with stock rom from samsung-updates.com / or cwm/twrp/chillpilz recovery for my device the flasher complete and pass..but after auto rebooting just got black screen,and if press power got back to firmware upgrade encontered an issue.
here the odin log :
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P3100XXCME2_P3100OLBCME2_P3100DXDLL1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> system.img
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> MLO
<ID:0/004> param.lfs
<ID:0/004> Sbl.bin
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
tired use another odin version just get flashing FAIL and other gt-p3100 still stuck firmware issue
anyone can give me another solusion ?
i aready read all thread in forum xda about flashing/brick/recovery...but still no luck

Cant flash official 7.0. ROM

Hello,
I had the official samsung 6.0.1 rom on my S6 Edge F version and now I tried to install the 7.0 nougat official ROM on the same s6 edge.
This is the error message:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Using Odin 3.11 and just selection the ROM at AP. And now I cant boot anymore, getting "use smart switch"-message. Why is this happening? How can I fix this?
Thanks in advance.

Turkishflavor said:
Hello,
I had the official samsung 6.0.1 rom on my S6 Edge F version and now I tried to install the 7.0 nougat official ROM on the same s6 edge.
This is the error message:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Using Odin 3.11 and just selection the ROM at AP. And now I cant boot anymore, getting "use smart switch"-message. Why is this happening? How can I fix this?
Thanks in advance.
Click to expand...
Click to collapse
Take the latest version of Odin. (Odin3 v3.12.3)
https://forum.xda-developers.com/showthread.php?t=2711451

1.wipe
2.Flash with latest Odin bininga59 said you!
3. wipe once again, restart the device!
Done.

Turkishflavor said:
Hello,
I had the official samsung 6.0.1 rom on my S6 Edge F version and now I tried to install the 7.0 nougat official ROM on the same s6 edge.
This is the error message:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1101)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> cm.bin
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Using Odin 3.11 and just selection the ROM at AP. And now I cant boot anymore, getting "use smart switch"-message. Why is this happening? How can I fix this?
Thanks in advance.
Click to expand...
Click to collapse
what's your region firmware (csc) & baseband you try flashed?

if you have an international model sm-g920F, be careful what firmware you download, dont download the ones that vodafone e.g. creates, take the one for your country without the company name

[Q] Possibly bricked GT-N8010

Hey,
I was successfully running LineageOS on my GT-N8010.
However, it froze at one point and I force turned it off, and ever since I just get the 'Firmware upgrade encountered an issue' screen. However, I am still able to get into download mode.
I'm now wanting to get it back to stock so I can re-try LineageOS on it. I have the stock image but if I try to install through ODIN I just get an error(posted below) and also on the tablet I get SW Rev. Invalid magic string.
Any idea how I could try sort it out?
In the details section of the download screen it shows;
ODIN MODE
Product name: GT-N8010
Current Binary: Samsung official
System status: Custom
Log:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Binary Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1100)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> tz.img
<ID:0/004> NAND Write Start!!
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Odin requires TAR files not image .
Flash stock rom via Odin .
Sboot.bin fail means you are flashing firmware with an older bootloader than is currently on the device .

JJEgan said:
Odin requires TAR files not image .
Flash stock rom via Odin .
Sboot.bin fail means you are flashing firmware with an older bootloader than is currently on the device .
Click to expand...
Click to collapse
Edit:
Looks like I didn't have the latest version, tried a newer one but it now gets stucks and after about 5mins of trying it stops at system.img;
Logs:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1301)..
<ID:0/004> File analysis..
<ID:0/004> Total Binary size: 1746 M
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> tz.img
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Stuck on system.img means odin not recognized your system partition..
And or change USB port change usb cable .

Make sure that you have the least official firmware for your device and if it still fails,
it looks like a eMMC failure.
This problem is very common on the N80XX devices.
I already had to replace hundreds of eMMC's on them.