Related
Hi, has anyone on here ever managed to stick a screen protector on their desire without air bubbles underneath? I must have gone through at least six and still can't bloody do it..
Sent from my HTC Desire using XDA Premium App
Whiskeybreath said:
Hi, has anyone on here ever managed to stick a screen protector on their desire without air bubbles underneath? I must have gone through at least six and still can't bloody do it..
Click to expand...
Click to collapse
Yes, it's quite simple once you figure it out. Make sure you place on as flat as possible and before you take the second protector film off smooth it down onto the screen slowly and use an applicator to smooth it on slowly. If you don't have an applicator just use a credit card.
It does take some practice though
I tried some screen protectors, but for me the Zagg Invisibleshield is the no.1
Easy to put on and managed to put it on without any bubbles (2 times).
davebugyi said:
I tried some screen protectors, but for me the Zagg Invisibleshield is the no.1
Easy to put on and managed to put it on without any bubbles (2 times).
Click to expand...
Click to collapse
Not cheap though. Had a look at Amazon and they're expensive and the reviews aren't too good either.
I have put quite a few screen protectors on- for family and friends, all of them are still bubble/dust free. All of these are the 'cheaply priced' one from ebay
The key things are :
Make sure the surrounding area where you are applying the protector is dust free- somewhere like a bathroom/shower room is best.
Clean the screen thoroughly with a lint-free cloth (usually provided with the protector).
Remove the 'number 1 plastic protector film only a bit at time, exposing as minimal as necessary, whilst using a credit card (with a thin lint free cloth over it) to press the the film from one end as you remove the protector film from othe other end.
As said above, keep the 'number 2 protector' on and smooth out any bubbles again with the credit card.
Peel off the 'number 2 protector'. Be careful, this sometimes 'raises' the actual protector off the screen and can allow dust to get in.
If any bubbles do appear after taking the number 2 protector off, use the credit card wrapped in a lint cloth to smooth them out (the cloth will of course prevent scratches).
Sometimes, dust can get in whilst you are applying. You WILL need to remove the protector and wash it thoroughly under running water.
I have had to do this a few times. Do not dry the protector with anything; you can actually apply it on wet (much like car window tint). You can squeeze out any excessive water out to the edge, again with the credit card. Just have another piece of cloth ready to absorb the excess and avoid getting it in the speaker.
Any Matt protector for suggestion??
vmax007 said:
Any Matt protector for suggestion??
Click to expand...
Click to collapse
Try these on ebay.
U use a credit card its more easier and then I push the big air bubbles out .. it doesn't matter if there are a couple of small air bubbles as they will fix themselves
Sent from my HTC Desire using XDA App
xybadog said:
Try these on ebay.
Click to expand...
Click to collapse
How resistant to scratches are these?
My current one is ok, but has got scratched pretty quickly.
reaper7881 said:
U use a credit card its more easier and then I push the big air bubbles out .. it doesn't matter if there are a couple of small air bubbles as they will fix themselves
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
Yes with CC it's more easier and if you do it right than you will not have bubbles
BluNoze said:
How resistant to scratches are these?
My current one is ok, but has got scratched pretty quickly.
Click to expand...
Click to collapse
Pretty good. I've had no scratches at all.
screen protectors are a must i think
xybadog said:
Pretty good. I've had no scratches at all.
Click to expand...
Click to collapse
Thanks, I'm now off shopping!
You could also try:
http://www.amazon.co.uk/FoliX-FX-CLEAR-screen-protector-Desire/dp/B003IMVJ2K/ref=sr_1_1?ie=UTF8&qid=1313400394&sr=8-1
It fits very good and keeps your display scratch free
I bought a pack of 3 on ebay and they work great, the touch sensitivity seems fine with it on.
Cost 99 cents.
Sent from my HTC Desire using XDA App
I have been using my Desire for about 13 months till now and I always carry it in my pocket.
I do notuse any screen protectiona and I still have not a single scratch untill now...I dunno if the protective screen is really necessary.
I wish I'd fitted a screen protector. I keep my Desire in a pouch but still managed to scratch the screen. Only a small one, but it still annoys me!
I always used cheap ones from ebay, even the ones sold with my hard-cases.
Here's i do (method found here on xda) : just take a warm/hot shower if there's "water" on the mirror, then you're good to go as the dust will be on the floor.
Then you just have to use the method here:
http://forum.xda-developers.com/showpost.php?p=16239021&postcount=5
I have my desire since 8 months ago without any protection and the screen is perfect, as the first day. No matter if you carry anything made of metal in the same pocket your desire is. It's almost unscratchable
I find that screen protectors dull the look of the screen somewhat. Just take care not to carry coins or keys in the pocket along with the phone.
Does any of you proud X owners think that if one applies the a screen protector incorrectly (bits of dust between the protector and the screen) or something similiar, that it could cause the screen to scratch, having a sand-like effect? I'm really paranoid about the screen when it's naked...
btw. how the hell am i supposed to put on a protector without air bubbles? Seems impossible.
I dunno about the first question. But you're supposed to be able to put it on using a credit card to smooth it out as you apply it. In saying that, I've never done it successfully
Sent from my One XL using XDA Premium
lukas_1 said:
Does any of you proud X owners think that if one applies the a screen protector incorrectly (bits of dust between the protector and the screen) or something similiar, that it could cause the screen to scratch, having a sand-like effect? I'm really paranoid about the screen when it's naked...
btw. how the hell am i supposed to put on a protector without air bubbles? Seems impossible.
Click to expand...
Click to collapse
I doubt having anything under the screen protector would harm these screens. The junk stuck under it isn't going to move as it's stuck in the adhesive.
The best way to apply them (for me anyways) is to clean the screen with an LCD cleaner (or make your own), use tape to blot up anything else, wipe again.
Next--I have found by taking the first layer of the film protecting the screen protector upside down works best. Dust and debris can fall and settle on the sticky side. Then carefully apply. As long as you don't touch the adhesive side, you can pick it up and keep applying the protector until you get it right. You want the top of the protector just about even with the AT&T globe.
Enjoy.....
By using tape do you mean using scotch tape, sticking it on the screen and pulling off?
I'll try washing my screen protector, drying it up, cleaning the screen with MF cloth, taping it up and then hopefully I'll be able to apply it perfectly! :fingers-crossed:
lukas_1 said:
Does any of you proud X owners think that if one applies the a screen protector incorrectly (bits of dust between the protector and the screen) or something similiar, that it could cause the screen to scratch, having a sand-like effect?
Click to expand...
Click to collapse
If you trap a particle of dust under the protector that has a hardness greater than the screen, yes, it will eventually scratch the screen in that spot.
However: Gorilla Glass has a Mohs hardness of around 9, which means there is not a lot in the mineral world that can scratch it. The likelihood of your trapping something like that under the screen protector, if you apply it correctly, is not great.
You should be able to remove a particle big enough to scratch your phone from the screen protector without having to wash the protector. I think you would ruin the screen protector if you wash it.
I've used packaging tape as it leaves no residue. Done it for years before with iPhones before owning an Android.
Sent from my HTC One X using xda app-developers app
When you apply your screen protector, do it in a washroom with a hot shower running. The steamy air will prevent dust from getting under it.
I will try that out. I always seem to get a bit of dust or lint on the corner of my screen protectors.
flar2 said:
When you apply your screen protector, do it in a washroom with a hot shower running. The steamy air will prevent dust from getting under it.
Click to expand...
Click to collapse
Just don't wait too long, not sure if the humidity sensor would get affected.
The way I do it: obviously, I clean the screen then remove completely the clear layer from under to make sure no dust will fall in. I'm holding the screen protector with the tips of my fingers on the sides and gently bend it across (the long) median then align with the phone's screen (this is the hard part). Put the screen protector on the screen at this stge the contact area will be the median line, and then use a credit card and work your way to the eges (one side at a time). I never got any bubbles under this way. I caught some dust particles few times though. It takes patience but it pays off, currently I have no dust or bubbles on it.
Sent from my HTC One X using xda app-developers app
iElvis said:
If you trap a particle of dust under the protector that has a hardness greater than the screen, yes, it will eventually scratch the screen in that spot.
Click to expand...
Click to collapse
If the particle is trapped in one place and can't move, I don't see how it can cause a scratch.
Plus, if any dust gets on the screen during the application process (as long as you've done a halfway decent job), its probably airborne. So its not grit or sand or anything like that (which would just fall to the ground instantly) but more likely skin, ash, etc.
A little preparation and a few tricks will go a long way to a good screen protector install. My process is:
1) Use a wet apply protector. Don't know why, but I've had vastly better results (no dust under protector) with wet apply rather than dry ones. I got to the point where I can do a dry type almost flawlessly, but only after lots of practice and a great amount of care. But even so, there still tends to be a dust particle or two. With wet apply, the first one I ever tried was perfectly dust free with little effort, and the subsequent ones also.
2) Before starting, examine the protector and see how it fits on the phone. With the backing still on the protector, place it on the phone's screen and match up the openings and edges to familiarize yourself.
3) As previously mentioned, use steam to pull dust out of the air. I run a hot shower for 5-10 minutes, then apply the protector in the bathroom. It won't eliminate all the dust, but makes a big difference.
4) Wipe the screen off with a micro-fiber cloth (often included with better quality wet apply protectors).
5) Blow off the screen with a can of compressed air (the kind used to dust electronics and whatnot) to get rid of any remaining dust.
6) Spray the application solution. Quickly apply the protector. As another mentioned, don't hold the sticky side up after you take the backing off, or it will instantly catch dust. Put the protector on quickly, don't let the sticky side touch anything but the screen. Handle the protector as little as possible, and by the edges.
7) Squeegee the protector down with a credit card (make sure the edge of the card is smooth) or some protectors will include a rubber squeegee. Blot the excess moisture at the edges. Then leave the phone alone while it dries.
The best investment for my smartphone has been Ghost Armor. I have spent so much money on packs of screen protectors. A couple years ago I decided $45 was worth it if I only needed to do it once a year. You won't regret it, and you don't have to install it.
Npsacobra said:
The best investment for my smartphone has been Ghost Armor. I have spent so much money on packs of screen protectors. A couple years ago I decided $45 was worth it if I only needed to do it once a year. You won't regret it, and you don't have to install it.
Click to expand...
Click to collapse
I've also heard horror stories about peoples phones not working after they are done or the screen not functioning afterwards. And since you sign an agreement they aren't liable
No thank you
Sent from my One X using Tapatalk 2
Npsacobra said:
The best investment for my smartphone has been Ghost Armor. I have spent so much money on packs of screen protectors. A couple years ago I decided $45 was worth it if I only needed to do it once a year. You won't regret it, and you don't have to install it.
Click to expand...
Click to collapse
I replace about 3 screen protectors a year (bought from amazon clear ones, 3 for $1.99). Other than a little rainbow effect when the screen is off, no regrets looks just like glass. I've been through many protectors before (ridiculously many on my first 'smartphones' rip moto ming, touchpro 1&2) but I can't justify the cost anymore, I'd rather have none (since I change my device every 8-12 months).
Sent from my HTC One X using xda app-developers app
I went with ghost armor myself, they installed for like 22 bucks.
No issues to report.
WR
Sent by WR's O/C'd One-XL on CR-V
Npsacobra said:
The best investment for my smartphone has been Ghost Armor. I have spent so much money on packs of screen protectors. A couple years ago I decided $45 was worth it if I only needed to do it once a year. You won't regret it, and you don't have to install it.
Click to expand...
Click to collapse
Screen protectors that come in packs are crap. The higher quality kind that cost $15 or so (Skinomi, Zag, etc) are in a different class. I've had a Skinomi on my One X since release (May), and one on my Flyer for almost a year and a half. Both are still looking great.
Sent from my HTC One X using xda app-developers app
I've never used a screen protector. Don't like the feel of them. This phone has great glass. I'm a mechanic and I keep my phone in my pocket all day (screen towards my leg of course) and not one scratch
Sent from my HTC One XL using xda app-developers app
I use Xtremeguard. Wet application and every time I get a perfect install. No bubbles no particles.
Sent from my HTC One XL using Tapatalk 2
charlieb620 said:
I use Xtremeguard. Wet application and every time I get a perfect install. No bubbles no particles.
Sent from my HTC One XL using Tapatalk 2
Click to expand...
Click to collapse
Was gonna say the same bout my Zagg...love it! Wet application and a squeegee, works perfect every time. The wet app also can aide with alignment if you don't get it just right, you can still move it before you squeegee.
Sent from my HTC One XL using xda premium
Not sure if this is still relevant, but I will put a vote for Ghost Armor as well. I have it for all my devices and it's like there's nothing there. Crystal clear and screen responsiveness is great. Had Zagg before and the orange peel feel and stickiness made me remove it. Those cheap packs aren't great either, they scratch up very very quickly.
I've seen a few videos on how to apply a tempered glass screen protector, but I'd like a few tips on how to apply one from those who have done it without any bubbles and problems.
What should I do to apply one without any problems? I have a new tempered glass screen protector and I want to install it without any problems.
TIA
vaibhav.ravi said:
I've seen a few videos on how to apply a tempered glass screen protector, but I'd like a few tips on how to apply one from those who have done it without any bubbles and problems.
What should I do to apply one without any problems? I have a new tempered glass screen protector and I want to install it without any problems.
TIA
Click to expand...
Click to collapse
Not gonna have bubble from a tempered glass screen protector. Most important thing is cleanliness. Removing every possible piece of dust/fiber/dirt/fingerprints/etc from the phone will make the application much cleaner and nicer. That, a steady hand, and some patience. But, this is probably better off in the actual forum about Accessories.
I applied a few screen protectors using as reference yt videos (nothing I invented).
Overall it's important to:
- plan plan plan. do your homework, see how and where it should fit (you can use the hinge method, but I usually find that a lot more error prone than good old preparation and careful placement and a lot of patience).
- work in a well lit environment.
- work in a clean environment (it is very well worth to apply the protector in the bathroom after a shower, or with the hot water running - settling all the dust).
- use no marks sticky tape the ones that are translucent white are the best - no need for any brand or something).
- clean the screen with a micro fiber cloth and some screen cleaning products (you should not over do it but it should usually clean and smudge / oil / lint free).
- use pieces of sticky tape to "tap and remove" any visible dust from the screen (usually I use a led flashlight to create an alternate spotlight on the screen to find dust).
- apply the protector and try to get it right in the first go (it is fairly important for glass protectors to not lift them). for regular protectors you can always lift them and remove dust, but double check about glass ones because those should not be lifted and reapplied as far as I know.
- smudge any bubbles as per the screen protector instructions.
in installed the MIME featherglass temperred screen protector...
suggestions?? CLEAN CLEAN CLEAN enviorment
(i did this)
go to your bathroom, wipe the counters clean....
pre clean your screen with a non streak cleaner...
clean it using a non fiber cloth for glasses
turn shower head to HOT and let it run a few minutes until your mirrors start to fog mirrors
wash hands, (no greasy fingers for this)
turn shower off, and leave door closed. start the process
once again, wipe the screen again! make sure u shake the cloth and wipe again
look at different angles to make sure its not dusty
take film off screen protector... hold by borders using the very tips of fingers
start by getting real close to the earpiece, center it, and ensure the borders are even....
keep getting closer, once it makes contact with earpiece and its centered, put a finger on it lightly to prevent movement...
before letting the screen protector down, make sure its lined up to be straight and just start to let gravity make the contact
squeeze bubbles starting from center towards borders if needed... i had not a single bubble...
i had to peel mine up to aligh it perfectly because i didnt do this above the first time
now i have a perfect protector with no dust, no bubbles and its awesome
es0tericcha0s said:
Not gonna have bubble from a tempered glass screen protector.
Click to expand...
Click to collapse
I meant the spider bubbles that everyone seems to be getting , I really wanna avoid those!
That, a steady hand, and some patience. But, this is probably better off in the actual forum about Accessories.
Click to expand...
Click to collapse
I tried, but since this is a Q&A forum, xda said I was better off posting it here. Anyways thanks for the info
kraven001 said:
I applied a few screen protectors using as reference yt videos (nothing I invented).
Overall it's important to:
- plan plan plan. do your homework, see how and where it should fit (you can use the hinge method, but I usually find that a lot more error prone than good old preparation and careful placement and a lot of patience).
- work in a well lit environment.
- work in a clean environment (it is very well worth to apply the protector in the bathroom after a shower, or with the hot water running - settling all the dust).
- use no marks sticky tape the ones that are translucent white are the best - no need for any brand or something).
- clean the screen with a micro fiber cloth and some screen cleaning products (you should not over do it but it should usually clean and smudge / oil / lint free).
- use pieces of sticky tape to "tap and remove" any visible dust from the screen (usually I use a led flashlight to create an alternate spotlight on the screen to find dust).
- apply the protector and try to get it right in the first go (it is fairly important for glass protectors to not lift them). for regular protectors you can always lift them and remove dust, but double check about glass ones because those should not be lifted and reapplied as far as I know.
- smudge any bubbles as per the screen protector instructions.
Click to expand...
Click to collapse
Thanks mate I'll post here once I've installed mine!
chaco81 said:
in installed the MIME featherglass temperred screen protector...
suggestions?? CLEAN CLEAN CLEAN enviorment
(i did this)
go to your bathroom, wipe the counters clean....
pre clean your screen with a non streak cleaner...
clean it using a non fiber cloth for glasses
turn shower head to HOT and let it run a few minutes until your mirrors start to fog mirrors
wash hands, (no greasy fingers for this)
turn shower off, and leave door closed. start the process
once again, wipe the screen again! make sure u shake the cloth and wipe again
look at different angles to make sure its not dusty
take film off screen protector... hold by borders using the very tips of fingers
start by getting real close to the earpiece, center it, and ensure the borders are even....
keep getting closer, once it makes contact with earpiece and its centered, put a finger on it lightly to prevent movement...
before letting the screen protector down, make sure its lined up to be straight and just start to let gravity make the contact
squeeze bubbles starting from center towards borders if needed... i had not a single bubble...
i had to peel mine up to aligh it perfectly because i didnt do this above the first time
now i have a perfect protector with no dust, no bubbles and its awesome
Click to expand...
Click to collapse
my bathroom doesn't have a counter, so I guess I'll leave my room for a couple of hours with the windows shut and try that! thanks for the tips!
I read somewhere in the past about using one of those GPS windshield (glass) mounts for installation.
It worked like a charm for me. What you do is stick the mount in the center of the tempered glass protector.. and drop it onto the screen. It's much easier to place perfectly and no accidental fingerprints along the edges.
TimeRunz said:
I read somewhere in the past about using one of those GPS windshield (glass) mounts for installation.
It worked like a charm for me. What you do is stick the mount in the center of the tempered glass protector.. and drop it onto the screen. It's much easier to place perfectly and no accidental fingerprints along the edges.
Click to expand...
Click to collapse
can you please elaborate? or link a vid? much appreciated
vaibhav.ravi said:
can you please elaborate? or link a vid? much appreciated
Click to expand...
Click to collapse
This video is for an iPad, but it should really visualize it for you: http://www.youtube.com/watch?v=T24l1wkB00s
I had a feeling suction cups like those might be hard to hold onto, so applied my tempered glass protector using the same method and a GPS mount
otaofans said:
This otao quality is high. You can see this one. I have bought this protector for my smartphone about two months. It still working well. I post my Attach Files for your reference.
Product list here:
1 xOTAO X-Lambo tempered glass screen film
1xInstructions frontage
1 xInstructions opposite side
1 xwet-dry cleaning pouch ( patent item:201320449448.2)
1 xEASY metal home button sticker (Aluminium alloy stripes textures )
1 xNano micro-fiber cleaning cloth
1 xAnti-static dust sticker
1 xModify sticker
Click to expand...
Click to collapse
This thread was about how you should apply a tempered glass protector.. All I can see is you suggesting to buy a new screen protector.
Besides that, you do realize that this thread is over 3 months old, right?
Otaofans only makes posts that promote the oato screen protectors. And for that reason alone I vote that none of us ever buy an oato product. Who's with me?
And report as spam...
Sent from my Nexus 5 using Tapatalk
I ended up with few of the small spiderweb bubbles under my Nilkin screen protector I installed last night. A few along the very top edge of the glass, and a few at the bottom. I am currently trying the binder clip with micro-fiber cloths trick to apply pressure and remove them. If that doesn't work, I saw a mention of putting the phone in a plastic bag and using a vaccuum hose.
1.) Has the vaccuum trick worked for anybody here.
2.) I got to thinking about this. I have a foodsaver vaccuum sealer for storing food. Would this do a better job of pulling out the bubbles since it creates a better seal?
I don't see how it could hurt the phone in any way. Others thoughts on this?
-Jeremy
What i would suggest :
Clean the screen with piece of cloth ( Mostly comes with the package)
Get some tape 2 pcs...
place one on the top of the screen protector , and pull it slowly to remove the screenprotector
get the other piece of tape and tape it around ur finger (Inside out) now with 1 finger u would pull the screen protector up
and with the other u would tap the screen where the bubbles are , this will make the bubbles go away!
Then just replace the screen protector and remove the tape, DONE!
PS: If this didn't help , then send your device to me i will fix it for free :good:
Bubbles are created by dust on the screen. I read someone suggest lift the protector with one piece of sticky tape then use another to remove the dust from the screen and protector. Do this for each bubble
Edit. Crap. Teaches me not to read the replies
Sent from my Nexus 5 using Tapatalk
Blowtorch em off
Sent from my Nexus 5 using Tapatalk
Assuming its not dust....just a bubble, like the huge one to the right of the led notification ....I used a thin cloth and an adjustable wrench and tighten the wrench firmly on the bubble...with the cloth protecting the phone of course. In 20 minutes per bubble....I had none. Gone for good.
Mime ghost glass BTW.
Sent from my N5 cell phone telephone....
I would suggest not doing it during night time. Do it on a very illuminated area. Clean with the provided cloth uniformly until looks perfect. I my self always blow the screen during the sticking process and never get dust between screen and protector. If any bubble, sweep it with a credit card before removing the top layer.
As someone said once you have them its a fail. I use the glass ones I know they crazy prices but I do the steam room bit and drop them on. No bubbles.
Sent from my Nexus 5 using XDA Premium 4 mobile app
You may (or may not) have noticed it is easier to apply screen protectors at times; you could apply them all day flawlessly, and other days they just don't play ball. The reason is humidity! The more humid the environment the less chance there is of dust particles wizzing around. Typically this will be summer here in the UK where its gets really humid. To replicate the humidity in colder climates / seasons, you can run a hot shower or bath and let the bathroom steam up. The screen protector should apply perfectly there, but you don't want to spend to long there with your precious phone, condensation and all. You could also try bowls of steaming hot water around the area you're going to be applying the screen protector in.
Be sure to apply common sense before applying the screen protectors if you're going to be using the above mentioned methods and the usual rules apply, clean the screen etc before hand.
So my idea worked and i now have a full adhesive screen protector. Covers from edge to edge and there is no halo effect. The protector is on good and does not peel/pop out. I am using a unicorn beetle pro full body case and no problems. Before the case would pop out the protector but not anymore.
What exactly was your idea?
How did you manage this? (For the people that haven't been keeping up with your posts, such as myself.)
Did you use LOCA or OCA film?
Sent from my Galaxy Note7 using Tapatalk
so much detail. so much wow. i wish there was more information, like, what you used, how you did it, instead of a brag post. thanks for the pictures though!
One of his older posts discussed using LOCA. If you use LOCA, how do you get it off if you ever want to remove the screen protector?
Yes I used LOCA glue. To take it off you just heat it. It should be easier to remove than when replacing the digitizer.
I got a couple air bubbles though but id rather have that than a scratched up screen lol
Interesting.... but more info on how to do it and what products to use would be great. Thanks OP.
I was just thinking about if this was a solution two days ago, but this is exciting news that its worked. My question is, is the LOCA a problem to handle, because i could see using too much might have some go into the speakers or just seep from the borders. when originally applied. and is there a way to make sure we don't get bubbles?
teegunn said:
Interesting.... but more info on how to do it and what products to use would be great. Thanks OP.
Click to expand...
Click to collapse
Donnyohs said:
I was just thinking about if this was a solution two days ago, but this is exciting news that its worked. My question is, is the LOCA a problem to handle, because i could see using too much might have some go into the speakers or just seep from the borders. when originally applied. and is there a way to make sure we don't get bubbles?
Click to expand...
Click to collapse
Yea i got a little on the speaker but you just have to be care full and as it seeps kut clean it with a rag. The good thing is that it wont dry until you put the black light on it. The part you have to be the most carefull with is the home button. Loca will make it sticky and a little harder to press. I also reccoment you get a protector that is completely clear as the one i got has black on the top and bottom and it prevents the black light from drying the glue under those areas. Clean the screen good. To avoid bubbles look at youtube and see how they apply it. Basically a stick figure but instead of a head it is a y shape. Carefully place the protector and let is slowly spread on its own. Once it stoos spreading then you could slowly press down on it and remove the remaining bubbles. I lined uo thw home and back buttons first and made sure the cut outs were aligned for the camera and sesors. Then i applied the black light on the bottom half furst so that it would align properly. I did this while pressing down on it because the air bubbles kept coming up. I also covered up the top half so that wouldnt dry up. Oncw i got the bottom i got rid of any air bubbles on the top half and did the same. After that i put the phone in a box., close it up, do a cut out for the black light to fit and let it sit for a couple minutes to dry more. Then i cleaned and dried the edges. Make sure not to leave too much of the loca in between the screen and protector so you wont get touch senaitivity issues. And do it where there is no dust. I oly got 1 small air bubble but some like white spots that appear to be dust. And again clean the speaker, home button, sensors, and camera before drying. You could also just scrape it off with a plastic blade that the loca came with. And make sure to use liquid version and not the film.