I got a bad ESN on my d2g. Is it bad for global use?
I'm using a forgein simcard from Vodafone NL. but I can't get the mobile internet working. EDGE as wel as 3G and HSDPA doesn't work for me. I will test it with t-mobile NL this weekend. Is this because of the bad ESN or lack of UMTS radio bands?
Any suggestions?
Edit: I already tried a hard reset, sbf and custom rom. The APN is set correctly.
I called vodafone and went to the store but they couldn't help me there.
At *#*#4636#*#* -> phone information -> radio bands -> Only USA band shows up.
Tested with T-Mobile and it works. So going back to the vodafone store.
...try Hard reset, then set Network Mode to GSM\UMTS, and Select Network to Automatic.
For Better GSM signal Select Network to GSM Only. In GSM Only works only EDGE internet connection.
Already tried, but with no succes, thanks for the reply
Have you added the required APN configuration?
Sent from my DROID2 GLOBAL using Tapatalk
well just so you know the ESN is only used on CDMA networks such as verizon, anything else would use the IMEI of the phone which is more of a international serial number so if the esn is bad it shouldn't matter because your network wouldn't even use the esn
I edited my TS, because I forgot to mention what I already tried
Fritsbenik said:
At *#*#4636#*#* -> phone information -> radio bands -> Only USA band shows up.
Click to expand...
Click to collapse
I have 9 options there, none of which says "USA band".
Here is the list I get:
WCDMA preferred
GSM only
WCDMA only
*GSM auto (PRL) (selected)
CDMA auto (RPL)
CDMA only
EvDo only
GSM/CDMA auto (PRL)
Unknown
Also - this is called "Set preferred network type", not "radio bands". I don't see "radio bands" anywhere under 'phone information'.
Try to flash the 2.4.29 full SBF. This should reflash radio and everything. Also - 2.4.330 has crappier radio performance when it comes to GSM/UMTS part of the phone. I would recommend you to stay with 2.4.29 if you are not using the phone on Verizon's CDMA
I mean radio bands try *#*#4636#*#* -> phone information -> menu -> radio bands ->
Already tried that SBF I didn't know there was another.
I gave up on the network because mister not so nice at the counter of the vodafone store. He basically said, We don't have it in our system so we can't help you! I switched to KPN NL and I have 3G and HSDPA without a lot of fuzz.
This post should really be a reply to the development thread found here:
http://forum.xda-developers.com/showthread.php?t=1412064&page=4
However, due to my lack of post count, I can't post it there.
In any case, I just wanted to say thank you to the OP. Utilizing the information in that thread and a few others, I was able to get my G2X to recognize 850 MHz UTMS providers. Although I haven't yet had a chance to test the data on these bands due to my current provider not having roaming agreements with them, it seems that being able to see the UTMS network may be a step forward.
Hopefully, I will have a chance to test further tomorrow and verify that the 1900 MHz UTMS band is also working properly.
If these tests prove successful, I will post details on how to enable these bands.
That's awesome, man! Hopefully it works when you test it tomorrow. Good luck
jwells777 said:
This post should really be a reply to the development thread found here:
http://forum.xda-developers.com/showthread.php?t=1412064&page=4
However, due to my lack of post count, I can't post it there.
In any case, I just wanted to say thank you to the OP. Utilizing the information in that thread and a few others, I was able to get my G2X to recognize 850 MHz UTMS providers. Although I haven't yet had a chance to test the data on these bands due to my current provider not having roaming agreements with them, it seems that being able to see the UTMS network may be a step forward.
Hopefully, I will have a chance to test further tomorrow and verify that the 1900 MHz UTMS band is also working properly.
If these tests prove successful, I will post details on how to enable these bands.
Click to expand...
Click to collapse
I am the OP of the thread you referred to, the one about the Qualcomm modem commands. I am very pleased that you were able to use that information to achieve the enabling of other cell radio bands which the modem is capable of but were not available for use. I tried too and was partially successful but not to the point of enabling the recognition of cell service providers which operate on those other bands. I hope that you have succeeded in achieving full operation of the 850 and 1900 MHz UMTS bands which will enable owners of the G2X/P999 phones to connect to networks which use those bands. I am looking forward to your next post.
Core Memory said:
I am the OP of the thread you referred to, the one about the Qualcomm modem commands. I am very pleased that you were able to use that information to achieve the enabling of other cell radio bands which the modem is capable of but were not available for use. I tried too and was partially successful but not to the point of enabling the recognition of cell service providers which operate on those other bands. I hope that you have succeeded in achieving full operation of the 850 and 1900 MHz UMTS bands which will enable owners of the G2X/P999 phones to connect to networks which use those bands. I am looking forward to your next post.
Click to expand...
Click to collapse
If I am understanding correctly, this would allow G2x phones to work with the new T-Mobile LTE 1900 Mhz signal, correct? Or am I way off base?
I believe it's AT&t's networks
jcbofkc said:
If I am understanding correctly, this would allow G2x phones to work with the new T-Mobile LTE 1900 Mhz signal, correct? Or am I way off base?
Click to expand...
Click to collapse
No. The LTE capability is not part of the Qualcomm mdm6600.
http://en.wikipedia.org/wiki/Qualcomm_Gobi
MDM6600™:
Multi-mode modem
HSPA+ with data rates of up to 14.4 Mbit/s
CDMA2000® 1xEV-DO Rev. A/Rev. B support
GPS functionality, including support for Assisted GPS
Since he hasn't posted anything since, it probably didn't succeed. I also sent him a PM which he didn't reply to.
jwells777 said:
This post should really be a reply to the development thread found here:
http://forum.xda-developers.com/showthread.php?t=1412064&page=4
However, due to my lack of post count, I can't post it there.
In any case, I just wanted to say thank you to the OP. Utilizing the information in that thread and a few others, I was able to get my G2X to recognize 850 MHz UTMS providers. Although I haven't yet had a chance to test the data on these bands due to my current provider not having roaming agreements with them, it seems that being able to see the UTMS network may be a step forward.
Hopefully, I will have a chance to test further tomorrow and verify that the 1900 MHz UTMS band is also working properly.
If these tests prove successful, I will post details on how to enable these bands.
Click to expand...
Click to collapse
Unfortunately, as suggested by Core Memory above, I have not been completely successful in this investigation; however, I will post what I discovered along the way for the benefit of others. Perhaps someone else can pickup where I left off and get things working.
First, a summary of the final status:
1) Updated NV Items to enable 850 MHz and 1900 MHz bands
2) Was able to see 850 MHz UMTS providers under the "Search Available Networks"
3) It appeared that a connection was being made to the UMTS provider based upon both the signal strength monitor in "About phone" and the Engineering Mode page that provides data regarding 3g connections
4) In the Engineering Mode page, it seemed that the device was trying to connect (login?) to the network but was not being successful with the login
5) When at the lock screen and forcing the connection to the 850 MHz UMTS network, the "Emergency Only" text appears further suggesting that the connection is working but that my configuration for the network may be wrong.
6) No 1900 MHz providers ever appeared in the network lists while searching. I am not sure whether this is because this band was not functioning or if it was because no such provider existed since I am not terribly familiar with the coverage where I am currently at.
For those who wish to follow this path and test in their own local markets, please see the following steps required to reach this point:
Tools needed:
1) QPST 2.7 (Build 366 or later)
2) QXDM 3.12.714 (or later)
Steps:
1) Install necessary tools on your computer.
2) Enable USB debugging (Settings-->Applications-->Development)
3) Connect phone to PC
4) In the hidden menu (1809#*999#), ensure that Port Setting is configured to CP USB.
5) Launch QPST Configuration
6) Under Ports, select Add New Port.
7) Locate your device and enable the port. (NOTE: There may be two ports available to you here. I believe that you want to use the one that is for Serial / USB/QC connections.
8) From QPST Configuration, launch the "Software Download" tool under the "Start Clients" heading.
9) From here, create a backup QCN file. This backup may or may not enable you to recover from making a mistake later. Also, there is alot of information in this file if you care to navigate through it.
10) Launch QXDM Professional.
11) View-->New-->Common-->NV Browser
12) Options-->Communications-->Target Port (Select your phone)
13) The previous step should have "enabled" the NV Browser lower pane
14) Read and record the following NV Items
a) (441) Band Class Preference (0xFFFF)
b) (946) Expand Band Preference 16 to 32 Bits (0xBFFF)
c) (2954) Bits 32 to 63 of Band Pref (0xFFFFFFFF)
d) (1877) RF Band Configuration (0x0000000002680380)
15) Update item 1877 per discussion below
16) Reboot phone
17) It may be necessary to configure the Modem Setting in the hidden menu to reflect the additional bands.
NV Item configuration discussion:
I am no mobile phone programming expert (< 4 hours playing with them at this level to date); however, as near as I can tell, item 1877 configures the hardware of the modem while items 441, 946, and 2954 appear to be some type of masking bits regarding what bands to prefer. As such, I believe that the original value of item 1877 enables the following RF bands:
(Bit:7) GSM (1800)
(Bit:8) GSM Extended GSM (E-GSM)
(Bit:9) GSM Primary GSM (P-GSM)
(Bit:19) GSM (850)
(Bit:21) GSM (1900)
(Bit:22) WCDMA Band I (2100)
(Bit:25) WCDMA Band IV (1700)
If you set 1877 to 0x000000006E80380, it should enable the following:
(Bit:7) GSM (1800)
(Bit:8) GSM Extended GSM (E-GSM)
(Bit:9) GSM Primary GSM (P-GSM)
(Bit:19) GSM (850)
(Bit:21) GSM (1900)
(Bit:22) WCDMA Band I (2100)
(Bit:23) WCDMA Band II (1900)
(Bit:25) WCDMA Band IV (1700)
(Bit:26) WCDMA Band V (850)
If anyone succeeds in getting any further using this information, I would be very curious to hear of your success. Also, please do share with the community such that we can collectively move forward.
Disclaimer: I accept no responsibility for any damage that you may cause to your phone with these tools or procedures. Please note that these tools give you fairly low-level access to your system that enable you to significantly mess things up. Further, please note that modifying the radio bands on this device may void your warranty and/or be in violation of local regulations as set by your local authority (e.g., the FCC).
jwells777 said:
Unfortunately, as suggested by Core Memory above, I have not been completely successful in this investigation; however, I will post what I discovered along the way for the benefit of others. Perhaps someone else can pickup where I left off and get things working.
First, a summary of the final status:
1) Updated NV Items to enable 850 MHz and 1900 MHz bands
2) Was able to see 850 MHz UMTS providers under the "Search Available Networks"
3) It appeared that a connection was being made to the UMTS provider based upon both the signal strength monitor in "About phone" and the Engineering Mode page that provides data regarding 3g connections
4) In the Engineering Mode page, it seemed that the device was trying to connect (login?) to the network but was not being successful with the login
5) When at the lock screen and forcing the connection to the 850 MHz UMTS network, the "Emergency Only" text appears further suggesting that the connection is working but that my configuration for the network may be wrong.
6) No 1900 MHz providers ever appeared in the network lists while searching. I am not sure whether this is because this band was not functioning or if it was because no such provider existed since I am not terribly familiar with the coverage where I am currently at.
For those who wish to follow this path and test in their own local markets, please see the following steps required to reach this point:
Tools needed:
1) QPST 2.7 (Build 366 or later)
2) QXDM 3.12.714 (or later)
Steps:
1) Install necessary tools on your computer.
2) Enable USB debugging (Settings-->Applications-->Development)
3) Connect phone to PC
4) In the hidden menu (1809#*999#), ensure that Port Setting is configured to CP USB.
5) Launch QPST Configuration
6) Under Ports, select Add New Port.
7) Locate your device and enable the port. (NOTE: There may be two ports available to you here. I believe that you want to use the one that is for Serial / USB/QC connections.
8) From QPST Configuration, launch the "Software Download" tool under the "Start Clients" heading.
9) From here, create a backup QCN file. This backup may or may not enable you to recover from making a mistake later. Also, there is alot of information in this file if you care to navigate through it.
10) Launch QXDM Professional.
11) View-->New-->Common-->NV Browser
12) Options-->Communications-->Target Port (Select your phone)
13) The previous step should have "enabled" the NV Browser lower pane
14) Read and record the following NV Items
a) (441) Band Class Preference (0xFFFF)
b) (946) Expand Band Preference 16 to 32 Bits (0xBFFF)
c) (2954) Bits 32 to 63 of Band Pref (0xFFFFFFFF)
d) (1877) RF Band Configuration (0x0000000002680380)
15) Update item 1877 per discussion below
16) Reboot phone
17) It may be necessary to configure the Modem Setting in the hidden menu to reflect the additional bands.
NV Item configuration discussion:
I am no mobile phone programming expert (< 4 hours playing with them at this level to date); however, as near as I can tell, item 1877 configures the hardware of the modem while items 441, 946, and 2954 appear to be some type of masking bits regarding what bands to prefer. As such, I believe that the original value of item 1877 enables the following RF bands:
(Bit:7) GSM (1800)
(Bit:8) GSM Extended GSM (E-GSM)
(Bit:9) GSM Primary GSM (P-GSM)
(Bit:19) GSM (850)
(Bit:21) GSM (1900)
(Bit:22) WCDMA Band I (2100)
(Bit:25) WCDMA Band IV (1700)
If you set 1877 to 0x000000006E80380, it should enable the following:
(Bit:7) GSM (1800)
(Bit:8) GSM Extended GSM (E-GSM)
(Bit:9) GSM Primary GSM (P-GSM)
(Bit:19) GSM (850)
(Bit:21) GSM (1900)
(Bit:22) WCDMA Band I (2100)
(Bit:23) WCDMA Band II (1900)
(Bit:25) WCDMA Band IV (1700)
(Bit:26) WCDMA Band V (850)
If anyone succeeds in getting any further using this information, I would be very curious to hear of your success. Also, please do share with the community such that we can collectively move forward.
Disclaimer: I accept no responsibility for any damage that you may cause to your phone with these tools or procedures. Please note that these tools give you fairly low-level access to your system that enable you to significantly mess things up. Further, please note that modifying the radio bands on this device may void your warranty and/or be in violation of local regulations as set by your local authority (e.g., the FCC).
Click to expand...
Click to collapse
You've made a lot of progress, your information is very useful. I'll use it for further exploration.
Did you test it with a SIM card with a data plan which uses those bands?
Do you know how to use QPST and/or QXDM flash the phone with a binary file for the baseband?
I did try to connect using sim cards with data plans on the specified frequencies.
As for flashing a baseband, it seems that you should be able to do so with these tools; however, I didn't look into it.
Sent from my LG-P999 using XDA
jwells777 said:
I did try to connect using sim cards with data plans on the specified frequencies.
As for flashing a baseband, it seems that you should be able to do so with these tools; however, I didn't look into it.
Sent from my LG-P999 using XDA
Click to expand...
Click to collapse
The following was done while my phone is using the WIND SIM card which is my carrier and is restricted to AWS (WCDMA 1700) and Network Mode is set to WCDMA only.
I used your instructions to enable the UMTS 850 and 1900 MHz bands. One clarification is necessary. The HexaDecimal number 0x6e80380 = Decimal number 115868544 = Binary number 0b110111010000000001110000000.
The binary number is read from right to left with the first binary bit on the extreme right designated as bit 0 of the 27 bit sequence. The binary number is the key to the hexadecimal number used to program the RF Band Configuration in QXDM. For example, according to Jwells777, bit 23 is set to binary 1 to enable WCDMA Band II (band 2) and bit 26 is set to binary 1 to enable WCDMA band V (band 5). Refer to Jwells777 post in this thread which states the binary bits used to set the phone to use the phone's bands. Here's a binary-decimal-hexadecimal converter: http://www.mathsisfun.com/binary-decimal-hexadecimal-converter.html
The HexaDecimal number 0x000000006E80380 can be entered directly for setting "RF Band Configuration" at line 1877 in the NV browser. The HexaDecimal number is converted into the decimal number 115868544 which will appear when another read is performed. In Engineering Mode, the SW Enabled Band reading of my phone changed from 0x0000000102400000 to 0x0000000106C0000. When I changed the phone's setting to Automatic Band Selection, the SW EnableBand reading changed to 0x0000000106e80180. Changing the settings for Band Selection and/or Network Mode will change the SW EnableBand reading on page 5 of Engineering Mode.
In Band Selection, I enabled WCDMA 1900 which caused my connection to WIND's AWS 1700 to drop. I Looked at page 5 (RF Calibration) of Engineering Mode to see which bands were activated and found:
WCDMA1 : 22.37, 22.45, 0.00
WCDMA2 : 0.00, 0.00, 0.00
WCDMA4 : 23.47, 23.19, 0.00
WCDMA5 : 0.00, 0.00, 0.00
WCDMA8 : 0.00, 0.00, 0.00
GSM850 : 32.70, 32.63, 0.00
GSM900 : 32.76, 32.71, 0.00
DCS1800 : 29.40, 29.50, 0.00
PCS1900 : 30.10, 29.90, 0.00
LOSS:
-1.06, -1.18, -1.24
-1.54, -1.64, -1.74
-1.80, -1.79, -2.01
-2.11, -2.21
The same readings occur with Band Selection set to Automatic or manually to any other band except AWS which is the UMTS band the phone was set up to use at the factory.
This indicates that WCDMA2, 5, and 8 are not RF calibrated but DCS 1800 and PCS 1900 are RF calibrated.
I also found that
When I do a network search, it finds WIND and Public Mobile which operate on UMTS 1700 (AWS) and Bell and Telus which operate on UMTS 850 and 1900 but not Rogers which also operates on UMTS 850 and 1900. (Rogers does appear if I search for GSM networks too.)
"In Canada, UMTS coverage is being provided on the 850 MHz and 1900 MHz bands on the Rogers and Bell-Telus networks. Bell and Telus share the network. Recently, new providers Wind Mobile, Mobilicity and Videotron have begun operations in the 1700 MHz band."http://en.wikipedia.org/wiki/Universal_Mobile_Telecommunications_System
That indicates it is able to receive signals on UMTS 850 (Band 5) and 1900 (Band 2) which should enable the phone to see TELUS, Bell and Rogers.
http://en.wikipedia.org/wiki/UMTS_frequency_bands
When I select connection to Bell or TELUS, the phone tries to register but fails with the message: "Unable to connect to this network at this time. Please try again later." That message is generated by the phone's firmware/software, not the network.
I haven't yet tested the phone with a SIM Card for Rogers or Bell or TELUS. A friend has a Rogers SIM card with a data plan but I don't think it will be of any use to test the phone's supposed additionally enabled bands.
Conclusions:
Cognitive overload.
I am finding this quite confusing because of the variable terminology used such as UMTS, WCDMA, PCS, DCS, and the various bands and transmit and receive frequencies used for each protocol. If someone could make more sense out of the information I've provided, that would be very helpful.
Questions:
Engineering Mode Page 5 (RF Calibration) indicate that WCDMA Bands 2,5, and 8 are not RF calibrated but DCS 1800 and PCS 1900 are. Does this mean that the phone will not transmit on the WCDMA Bands 2,5 and 8 because the RF calibration for transmitting is not available?
If anyone can add something useful to this thread, that would be greatly appreciated.
nvm sorry mood pls delete this
Glad to hear that someone else was able to see the other bands using the information that I posted.
I would also add that I am able to see att in the US but not connect. I receive the same error mentioned by CoreMemory. If anyone has access to an O2X and could provide the qcn dump, it may help configure any other NV Items related to the new bands that we have missed.
Sent from my LG-P999 using XDA
HELP
Core Memory said:
You've made a lot of progress, your information is very useful. I'll use it for further exploration.
Did you test it with a SIM card with a data plan which uses those bands?
Do you know how to use QPST and/or QXDM flash the phone with a binary file for the baseband?
Click to expand...
Click to collapse
hi i'm trying but when insert the code 1809#*999# send me a error " MMI CODE CANDELED "
jwells777 said:
Glad to hear that someone else was able to see the other bands using the information that I posted.
I would also add that I am able to see att in the US but not connect. I receive the same error mentioned by CoreMemory. If anyone has access to an O2X and could provide the qcn dump, it may help configure any other NV Items related to the new bands that we have missed.
Sent from my LG-P999 using XDA
Click to expand...
Click to collapse
I wonder if the qcn dump from the O2X is useful since it has a different modem, it doesn't have the Qualcomm MDM6600 which is in the G2X/P999.
If we could get a qcn dump from another phone which uses the MDM6600 on the bands we want to get working, that would be a lot of help.
The Qualcomm Mobile Data Modem Software Interface 80-Vr001-2 manual would be very useful too.
Core Memory said:
If anyone can add something useful to this thread, that would be greatly appreciated.
Click to expand...
Click to collapse
i think if you post that into LG Optimus 2x forums with some instructions and explaining them. we could get the configuration from them. Soo you could go and ask them and explain them how to get those codes.
EDIT: NVM i just REAd your last post.
If you guys need a tester for anything, im all ears
Core Memory said:
I wonder if the qcn dump from the O2X is useful since it has a different modem, it doesn't have the Qualcomm MDM6600 which is in the G2X/P999.
If we could get a qcn dump from another phone which uses the MDM6600 on the bands we want to get working, that would be a lot of help.
The Qualcomm Mobile Data Modem Software Interface 80-Vr001-2 manual would be very useful too.
Click to expand...
Click to collapse
I didn't think of the fact that the modems are different. I agree with you that it would probably be more useful to have the dump from a phone with the 6600 that is configured for the new bands
Sent from my LG-P999 using XDA
jwells777 said:
I didn't think of the fact that the modems are different. I agree with you that it would probably be more useful to have the dump from a phone with the 6600 that is configured for the new bands
Sent from my LG-P999 using XDA
Click to expand...
Click to collapse
I don't know of anyone with one. As well, the file contains info which the person who supplies it would have to trust us not to use.
we can ask those guys for the configuration codes it seems they use the same modem or item.
http://forum.xda-developers.com/showthread.php?t=992635#12257150
I'm customer of the local carrier "Drei" (Hutchison) but my Pixel (bought in Germany) does not connect to the 4G / LTE network.
The support of Drei is not able to help me. LTE is working fine with the same SIM on the OnePlus One.
Any clue how to fix that?
There is regional problem I came across. In India here we dont have VOLTE support on pixel
FallinHigh said:
I'm customer of the local carrier "Drei" (Hutchison) but my Pixel (bought in Germany) does not connect to the 4G / LTE network.
The support of Drei is not able to help me. LTE is working fine with the same SIM on the OnePlus One.
Any clue how to fix that?
Click to expand...
Click to collapse
What LTE bands do they use on Drei?
Same happen to me in Portugal with MEO. I can't seem to solve it. Talked with my carrier support, they don't know why I don't have 4G/LTE.
I never got 4G, but my SIMCard has no issues with iPhone getting 4G right away.
Is it Pixel issue? I start to think it is..
3/Drei is listed here: https://en.wikipedia.org/wiki/List_of_LTE_networks_in_Europe#Commercial_deployments
The specs of the Pixel are listed here: https://madeby.google.com/phone/specs/
That is all information I have got.
Is there any possibility to display information about nearby LTE senders via an app?
After activating "LTE only" via *#*#4636#*#* it works. Everytime I search for networks or reboot my phone it still connects via 3G and switches back to "LTE UMTS auto (PRL)".
Seems to be a software issue.
FallinHigh said:
After activating "LTE only" via *#*#4636#*#* it works. Everytime I search for networks or reboot my phone it still connects via 3G and switches back to "LTE UMTS auto (PRL)".
Seems to be a software issue.
Click to expand...
Click to collapse
I use the phone on Verizon and don't have any problems connecting to LTE using any available mode (Global, LTE/CDMA or LTE/GSM/UMTS). However, if I set the mode to LTE-only via the menu, it will also reset when I either reboot the phone or if I just open the "Cellular networks" menu. I think it's how it supposed to work because that menu doesn't have the LTE-only option, so it resets the mode to whatever you see there. The solution is simple - if you reboot the phone change the mode again and don't go to the "Cellular networks" menu
Regarding why it doesn't work with "LTE UMTS auto (PRL)", it might be because Drei didn't configure a handover from UMTS to LTE on the cell site you're connected to. It looks like Pixel finds UMTS signal first, but doesn't know that LTE signal exists due to a missing handover. Another phone might be fine if it searches for LTE signal first. But if you can see another phone switching from UMTS to LTE in the same spot, my theory is wrong.