Related
I'm interested to buy this, what do you guys think? For those who have this, any feedback, including its performance, would be appreciated. For the price, I can actually get two HTC or four Momax 900 mAh batteries, so I'm not sure if it's worth it. By the way, the cover is mat instead of glossy.
I found the pictures on Google.
Well, I really love the matt finishing and overall high quality. Thats the finishing that HTC should have given in the original batt.
With the old glossy surface, the pyramid peaks are very vulnerable to scratches, and you can see whitish tiny scratches on the peaks. With the ext-batt's rubbery surface, it's almost scratch proof. I've been using the batt for 4-5months and it's still perfect.
As for the thickness.. frankly, 14mm is still thinner than most PPCs out there.
Enough of aesthetics.. My phone now lasts >50% longer.. which is good for me. Thats abt 2 days with some MP3s. Used to be low end of every day, which makes no sense coz you know 15-20% batt won't get you through the whole of next day.
My advice is.. get the batt as a long term investment. If you're gonna sell the phone after 6mths, bear with the lousy original batt.
Hi MasK, thanks for the input, it's very helpful.
I think I will probably keep this phone till November or December, because by that time I can get a free phone from my provider, I will just sell that right away and the Diamond to get something new. Yeah the glossy finish is really easy to scratch, right now I've to use a case to protect it.
There is another option that I'm considering, it's the HTC battery bank BB G300. It's sightly more expensive, but I can keep it for future HTC phones or any phones that use the same connector. The only thing is I'm not a huge fan of carrying extra devices on me.
Extended battery
I decided to buy this battery when I one day ran out of battery at 7pm and desperately needed to send an email.
It certainly improved battery life by up to 50% and i don't think it makes the phone uglier. It's only a few mm thicker (i think 3mm) but only the fact that I get two days out of it with hotmail pushed and OWA pushed through emoze and average calling, texting emailing and surfing, should convince you to buy the battery.
The only problem I had was the HTC pouch that came with the phone. When you have the extended battery on, it won't fit your diamond any more, so I had to buy another one (a generic HTC leather pouch).
Hope it helps...
What I don't understand is, why do they only thicken the battery? They could also use the new space above and below the battery (looking straight onto the backside of the Diamond).
sgiannis said:
I decided to buy this battery when I one day ran out of battery at 7pm and desperately needed to send an email.
It certainly improved battery life by up to 50% and i don't think it makes the phone uglier. It's only a few mm thicker (i think 3mm) but only the fact that I get two days out of it with hotmail pushed and OWA pushed through emoze and average calling, texting emailing and surfing, should convince you to buy the battery.
The only problem I had was the HTC pouch that came with the phone. When you have the extended battery on, it won't fit your diamond any more, so I had to buy another one (a generic HTC leather pouch).
Hope it helps...
Click to expand...
Click to collapse
Thanks, same as MasK pointed out, it's good to know about the performance.
Chatty said:
What I don't understand is, why do they only thicken the battery? They could also use the new space above and below the battery (looking straight onto the backside of the Diamond).
Click to expand...
Click to collapse
I think it's not as simple to produce a battery in some odd shape, they also have to consider about the compatibility with other models.
I got mine last week and it's great.
Mat finis is actually better than glossy - no fingerprints and I think it's going to be more durable in the long run.
As for battery life - now I can use my Diamond normally for two days, I had to charge the normal battery every day.
alese said:
I got mine last week and it's great.
Mat finis is actually better than glossy - no fingerprints and I think it's going to be more durable in the long run.
As for battery life - now I can use my Diamond normally for two days, I had to charge the normal battery every day.
Click to expand...
Click to collapse
I just received mine today, I'm glad I went for it.
looks like im gonna have to invest in this battery...
I've decided to go for it, and have orderes the BP E270.
Can anyone recommend some cases that would fit the 3mm fattened diamond?
Thanks,
Dave
Having owned the extended battery (and getting rid of it). I have to say I didn't like at all, the phone just felt wrong. I appreciate it only make the phone a couple of mil thicker but trust me, it wrecks the feel of the phone. If the phone came with the exteneded battery to start of with, I may have been happy with it.
Another problem I had with it, was that the back was always coming loose and sliding forward when I tried to take the phone out of my pocket.
If you are having problems with the power of your phone, then by all means get the extended battery but I'm telling you the extended makes your phone feel like a brick and even worse, makes it feel cheap.
I tend to disagree, the phone feels much better in my hand (my opinion), I liked the thin looks of the phone with the original battery, but I could never hold it properly, it slipped from my hand a couple of times, lucky it fell on the carpet. Now I like it much better, plus having the added benefit of the extra power. At the end of the day, it's a question of choice, some of you might like it, some of you might not, I don't think there is a right or wrong answer here.
Mine has arrived, and I really like it. As said earlier, the matte finish is much better, and the small increase in size actually makes it easier/nicer to hold.
Any suggestions on a pouch or case that fits it?
The extended battery is actually the same thickness as the 900mAh battery with a silicon case ;-) Actually I normally use a Tek Sock pouch with my extended battery.. but for now, i just have a screen protector and will try for a few days without a pouch/case.
hi i got mine today its beetter than the old one htc must have done this before n replaced all batterys like nokia did for mathatushita battery which recently got blasted
i got it for RS-3,000 inr< indian national rupee> wat abt others cost
just got mine yesterday.. however mine is the white colour version.. so still have the glossy back cover..
i check the battery status using powerguard and the battery voltage is always around 3.9V to 4V.. and the phone gets heat up v fast.. to more than 39 degree.. is my battery faulty or it is normal for the extended battery to behave like this??
lingk said:
just got mine yesterday.. however mine is the white colour version.. so still have the glossy back cover..
i check the battery status using powerguard and the battery voltage is always around 3.9V to 4V.. and the phone gets heat up v fast.. to more than 39 degree.. is my battery faulty or it is normal for the extended battery to behave like this??
Click to expand...
Click to collapse
my phone heats up if im using it for video viewing. what are you doing with your phone when it gets that warm?
SUBLIMINALLYINC said:
my phone heats up if im using it for video viewing. what are you doing with your phone when it gets that warm?
Click to expand...
Click to collapse
im playing games.. but when using the original 900mAh battery, it wont get so warm.. with the extended battery, when it have around 80% battery left, the voltage is like 4.1V to 4.2V.. which i think is very high.. thats why causing the phone to heat up so much..
can anyone confirm with me that it is normal to get 4.1V to 4.2V when the battery life is more than 70%?? or is my battery faulty?? it will drop to 3.6V to 3.7V when battery life is less than 50%..
I've got mine today... I thinks it looks better than the glossy one and with the extra mAh...
Does anyone found a good case for the new package?
Anyone can help me find an another one battery, seems that it's ran out of stock now !
Does someone has this one?
3600mAh Mugen power
At "Special Price" of $104.95 I don't think I would want it. Back cover looks horrible, instead of making a hump they kept the width consistent with a slight curve.
My phone looks smaller with BALLISTIC case on. Battery life is no longer an issue if you have a small charger like below, just keep it in your pocket and charge your phone while it is not in use.
the reason there is no hump like on the HD2, is because the back cover is required to get a signal, due to the contact pins being right there. The back cover isn't a 3 piece back cover, so they can't make a part have a hump, and the rest not.
I have not used this one but I'm currently using their 3300mah for Nexus S...I payed their price and I must tell, they do a good customer support job for the price they ask for it.
Speedtest?
Can anyone shed light on why speedtest had a faster download with the extended battery installed?, is it simply more powerful because I would have thought the power was regulated by the phone itself?
Is it likely to be a better aerial in the back of the Mugen case?
Thanks.
Terry
That thing is ugly
If you have to replace the battery door, how do you expect the antennas to work?
That's... HUGE!
The size is too big, and out of my price range
I have one, it gives me enough power to last until the next morning without a charge. The wifi sucks now since the back doesn't have the metal antenna connectors, but everything else works fine. The back is ugly as hell, but its worth it to be able to last at least a day.
Sietan said:
I have one, it gives me enough power to last until the next morning without a charge. The wifi sucks now since the back doesn't have the metal antenna connectors, but everything else works fine. The back is ugly as hell, but its worth it to be able to last at least a day.
Click to expand...
Click to collapse
Wifi sucks? Have you asked mugen about this? It's very bad.
terryd1980 said:
Can anyone shed light on why speedtest had a faster download with the extended battery installed?, is it simply more powerful because I would have thought the power was regulated by the phone itself?y
Click to expand...
Click to collapse
The aerial is probably better than the original HTC one, so faster results, they could afford to make it a lot bigger as the back of the phone is a lot bigger
So far so good! Loving my new HTC Beluga!
All kidding aside though... Ditch the skinny Jeans kids, you're killing your sperm!
Thickness is not always bad thing (that's what she said)
galaktiker said:
Wifi sucks? Have you asked mugen about this? It's very bad.
Click to expand...
Click to collapse
Yes, they sent me a new back to the phone, but it didn't fix it. If I switch to the old battery/back then its fine and works great, but with the back they sent me, my range is now severely limited and certain ways of holding the phone drops my signal altogether.
Well a friend of mine is offering a mugen 3600mah(!) battery unopened for 50 euros... that's about half the price I can find it in retail.
I'm still waiting for my Anker batteries, but I'm -seriously- thinking of getting that as well... do you think it's worth the price, will it really get me ~2.5x the battery time I have now (including drain) or I'll end up with roughly 3-4 hours extra?
Just waned to add that Mugen Power has a slim solution that is OEM sized but still gives about 15% juice.
1950mAh
Dear all,
it is easy to find proposal for 3030mah batteries on web.
I check in the forum but I do not find review/comment about the satisfaction to integrate such batteries.
I wonder if one of you guys did try to integrate such battery?
Is it really bringing obvious advantage and is it easy to put in place?
Take care all,
Laurent
My battery is starting to get fat, but I'm too scared to disassemble the phone.
Has anyone had success replacing their batteries?
Sent from my XT890
No problem to disassemble it. First screws around screen, after that screws and tapes on motherboard and just tear out battery. If You can do it carefully You can even put back old battery.
Yes, very easy to disassemble. To make you comfortable with it, you go go on youtube. There are different video very clear about the procedure.
Seems the 3030mah battery does not wake up lots of interest.... I keep curious about it.
it's chinese.not better than the original.i've seen a lot of them....don't waste ur money.to maximize the battery life of the razr i just root,bebloat and greenify all the apps that you dnt use...mine lasts 2 days with data always on...
raol.xh said:
it's chinese.not better than the original.i've seen a lot of them....don't waste ur money.to maximize the battery life of the razr i just root,bebloat and greenify all the apps that you dnt use...mine lasts 2 days with data always on...
Click to expand...
Click to collapse
yeah. I guess there is no miracle and if people would be able to put 3030mah in a battery sizing 2000mah, we would probably already know.
Anyway, I did like you say. I rooted and put Omar Rom(July 16). So far, I am very suprised by the stability and the efficiency of this rom.
I saw two small defects that I can not report as no access yet to the developer chat room.
Then today, thanks to your update I discover greenify. Looks perfect and no ads in.
Thanks !
I had one of those for my XT925. Removed the Golden patch: big surprise: The Cell is labeled 1900mAh.
I put a new genuine Motorola battery in my phone last week. It is really easy to do.
6 screws around edge of phone. Pry off the plastic piece at mouthpiece, 3 screws under it, pry off Motorola badge at earpiece, 2 under it. Gently separate phone and disconnect ribbon cable. Then 7 screws around mother board, pry off battery connector bottom left and camera module at top. carefully lift board adn undo clip at earpiece and remove that section. Board should now lift off. Battery is stuck to back of phone with double sided tape that covers top half of battery. I used a lollipop stick to pry battery away. You can use a hairdryer to heat tape up to make it easier. Job done
Video: https://www.youtube.com/watch?v=eWRipBG5iPY
Where do you buy your battery? Has the battery good health and capacity? I have to buy new battery too, but I don´t know where. A lot of sellers are on Ebay, but everything are unofficial batteries.
Hey guys. I've tested this on my Note 4 and it fits! The volume rocker, power button and S-Pen slots all line up. The case does protrude a bit on the sides, however it is very minor and I am now using this as my daily driver.
This does Rapid Charge passthrough for the phone and has a full spare USB-A slot to charge a second device (not rapid charge though). The battery itself does not rapid charge in nor out but passes the rapid charge through to the phone while charging the battery.
Pictures to come.
Link below...
http://www.amazon.com/gp/product/B0194NP5IK/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B0194NP5IK&linkCode=as2&tag=techronico-20&linkId=V6MJBSU43A6WJQ5G
Interesting.
I'd like to see those pics when you can. I'm interested in seeing how it looks on the phone.
How does the case affect the phone weight? I've never played with the case.
Sent from my SAMSUNG-SM-N910A using Tapatalk
If this one works I wonder is others will work too?
That's not a good idea i think.
You will loose sound cause the speaker is covered though.
Interested to see if this works. I find it frustrating to use the 10,000 mah extended battery from zerolemon as it never reads correctly even with the beast mode kernal that has the zero lemon fix. Post those pictures please.
i doubt about fitting part cause of note 5 camera n flash position compare to note 4 .
Good point
Are you using correct zero lemon kernal with your note 4 not hundred percent accurate but very good
can we see some pictures of your note 4 with the note 5 battery? i will get one asap if this really fits well.
Techronico said:
Hey guys. I've tested this on my Note 4 and it fits! The volume rocker, power button and S-Pen slots all line up. The case does protrude a bit on the sides, however it is very minor and I am now using this as my daily driver.
This does Rapid Charge passthrough for the phone and has a full spare USB-A slot to charge a second device (not rapid charge though). The battery itself does not rapid charge in nor out but passes the rapid charge through to the phone while charging the battery.
Pictures to come.
Link below...
http://www.amazon.com/gp/product/B0194NP5IK/ref=as_li_tl?ie=UTF8&camp=1789&creative=9325&creativeASIN=B0194NP5IK&linkCode=as2&tag=techronico-20&linkId=V6MJBSU43A6WJQ5G
Click to expand...
Click to collapse
Hey can you send some pictures so we can take a look at what your working with???? Lol I hope you read this before the note 6 comes out... Lol
divineazn716 said:
Hey can you send some pictures so we can take a look at what your working with???? Lol I hope you read this before the note 6 comes out... Lol
Click to expand...
Click to collapse
Sorry, this mod was good, but I moved to the Huawei Mate 8 too fast after this and didn't take pictures before selling the phone with the case.
Techronico said:
Sorry, this mod was good, but I moved to the Huawei Mate 8 too fast after this and didn't take pictures before selling the phone with the case.
Click to expand...
Click to collapse
OK no problem, but how much more bulky was the phone? Does it become bulky like other zerolemon products or is it a slim style? Thanks for getting back to me even though ur not on the note 4 anymore. Do you like the mate 8?
divineazn716 said:
OK no problem, but how much more bulky was the phone? Does it become bulky like other zerolemon products or is it a slim style? Thanks for getting back to me even though ur not on the note 4 anymore. Do you like the mate 8?
Click to expand...
Click to collapse
The Mate 8 is the best phone ever made!
xmax2323 said:
i doubt about fitting part cause of note 5 camera n flash position compare to note 4 .
Click to expand...
Click to collapse
Same! I don't think this mod would ever work properly.
Sent from my SM-N910V using XDA Free mobile app
There's no way that this case would fit a Note 4 and be a good idea. 1. The battery case completely covers the speaker and no sound is present. 2. The camera flash and camera itself are not located in the exact areas, whereas you'll be interfering with the lens etc. 3. The charging I this thing socks cause the connection is done thru a modified male micro USB connector which takes literally twice as long to charge and the correct battery. 4. Unless you have insurance on your phone, why risk 2 millimeters of loose play on the side of the TPU case? In my opinion, the most obvious choice, would be to use the correct battery with the correct phone. That's just my opinion, lol
Developers don't need no stinkin' signature!
If I've been able to help you, please hit the "Thanks" button. *
I had an idea.
I previously owned an S10e that was second hand and the phone's battery was so bad it couldn't last through the day.
S10e battery ( EB-BG970ABU )
I was craving for a big battery so I ordered a Samsung M51 with a large 7000mAh battery but I still cant get over the feeling of a small phone in my hands. I loved my old A5 2017 and s10e is almost the same size.
So I was thinking maybe I can upgrade the battery. Both S10 and S10+ have a bigger battery as in capacity and dimensions. But then I looked for an earlier phone. S9?
S9+ battery ( EB-BG965ABU )
It has the same connector but I don't know the dimensions so I was hoping any1 can help me with this case.
Thx to all. <3
YoungPumpkin said:
... I don't know the dimensions so I was hoping any1 can help ...
Click to expand...
Click to collapse
The S10e stock battery measures 42mm wide, and 71mm tall; not counting the circuit piece, which adds another 5mm to height. My battery is still glued in, so I can't measure its thickness (yet). I too have been thinking about changing my battery (downsizing), but the apparently attached circuitry is puzzling:
Thx soo much for this information. Im searching far and wide and the closest thing is the s9+ battery as mentioned. I will try to find some infortation and wll go on from there as im probably not the only one trying to get the most out of a great phone.
Ohhhh ok then.
I asked store owners on aliexpress selling batteries and they were kind enough to send me this. It's sooo close.
So it appears alternative batteries come with their own attached circuitry on top. Might work for you @YoungPumpkin but probably not for my wish to downsize. Your wish for more mAHr capacity will hinge on making larger battery fit. Phones of the past did this via thicker battery and special back cover with a little buldge.
I could desolder the cercuit of the pther battery and solder it to the new one as thats how they are connected right? If i wanted to fit the bigger battery in the s10e i would have to modify the phones metal body and thats not a problem. But idk if it would work software side of things. And what do you mean by downsizing? Why do you need a smaller battery?
I prefer a light weight phone; had S4 Mini for years. It was under 4 oz. Was forced to upgrade due to poor voice connections due to carriers changing to VoLTE. S10e was the least of the heavy weight evils for me. I have chargers everywhere, on my desk, next to bed, near easy chair, in my car, etc. The lowest my S10e battery has ever been is 82%. I'd like to take an ounce off its weight.
Ohhh. Then battery is ur only way of waight reduction or maybe if u find a custom plastic back. Thx for your help anyway.
The s7 edge had a 3600 mAH battery , 100 plus than the s9 , and if ur into desoldering, you surely could do it , and if you do, post a guide as well .
I think soldering the chipset of the battery isn't the problem. It has to fit or at least almost fit without destroying the chassis too much. I"ll check the dimensions of the batteries and compare them.
Back in the day they used to swap the s7e's battery onto S6 flats , so surely you will find the proper dimensions for it , also the phone is a tad smaller than the s9 , close to the s10e's dimensions so by that logic, the battery should fit better ?
here's something to give you an ideea about soldering the connector thingie on the other battery Battery connector swap
the soldering part is the easy part. I'm worried the battery won't fit because of the size. s10e's battery is roughly
I just noticed there is a code on the battery that determines its size 1/CP6/44/77 [s10e] and that's where it bottles up.
damn, s10e's battery is THAT small? pff, what's the size of the s9+'s then ?
i think the s9+ is pretty close
Maybe if you flip that top connector , in case it is flexible , then there shouldnt be a size difference issue .
Also dont they make the cutouts for the batteries bigger now, to allow them to expand (since the note 7 issue ) ?
Let us know of your progress, I have an s10e as well & it's brand new for now, but if you manage to get a bigger battery in it, i will open the back glass too .
I was planning to upgrade the battery when I bought the s10e the second time but I wasn't sure so I opened the form to talk out the possibilities. as of right now my battery isn't that bad but when it does get bad I might upgrade because I like the form factor of the phone.
Hey there,
I've been searching around for a topic like this since forever now, only thing i could find is a YouTube video which wasn't clear enough.
Since my battery health was already dying on s10e i thought about an upgrade instead of replacement but couldn't find similar dimensions to s10e's battery.
Then i got a juice pack but it made the phone bulkier and the continuous charge would heat up the phone + increment on the charge cycles of the battery.
Already tried s9+ battery but it doesn't fit in the frame horizontally
Though vertically it was a perfect fit and a bit thicker overall
I replaced the complete pcb, removed the battery's covering and adhesive strips , didn't make much of a difference either.
I've contacted a lithium ion battery manufacturing unit located in china
Who make custom batteries with your preferred dimensions but in Bulk and they were ready to ship 20 pieces for 7$ each .
But i highly doubt their performance or long term usage when compared to the Samsung manufactured ones .
Also you'd have to desolder the current pcb from your phones battery or else source PCBs from china in bulk again .
How much battery does it stick out horizontally? And what would be the custom battery capacity? I think the only option is a s9+ battery to my beliefs.
emadhamid said:
Hey there,
I've been searching around for a topic like this since forever now, only thing i could find is a YouTube video which wasn't clear enough.
Since my battery health was already dying on s10e i thought about an upgrade instead of replacement but couldn't find similar dimensions to s10e's battery.
Then i got a juice pack but it made the phone bulkier and the continuous charge would heat up the phone + increment on the charge cycles of the battery.
Already tried s9+ battery but it doesn't fit in the frame horizontally
Though vertically it was a perfect fit and a bit thicker overall
I replaced the complete pcb, removed the battery's covering and adhesive strips , didn't make much of a difference either.
I've contacted a lithium ion battery manufacturing unit located in china
Who make custom batteries with your preferred dimensions but in Bulk and they were ready to ship 20 pieces for 7$ each .
But i highly doubt their performance or long term usage when compared to the Samsung manufactured ones .
Also you'd have to desolder the current pcb from your phones battery or else source PCBs from china in bulk again .
Click to expand...
Click to collapse
Can you share some pictures or the video perhaps so we can have a look at them ?