Related
well, when you start with your new 9001 you will get confused by adm, sdk and weird things like that. Take your time - you don't need it for the beginning - just follow these steps:
1) root (easy) http://forum.xda-developers.com/showthread.php?t=1253707
thanks to KeksKlip - (to get into recovery you need to shut off, press Volume up and Power until Samsung appears, then wait for the box and press menu)
2) recovery (not so easy) - you will be happy to have a backup, so this is really wise to install it. The recovery from RomManager does not work - you have to install this modded recovery.
http://forum.xda-developers.com/showthread.php?t=1331164 [Release]FeaMod Recovery 1.4 - based on CWM Recovery v. 5.5.0.4. thanks to manveru0
[EDIT: you can now flash FeaMod v1.4 via Odin: try this link http://dl.dropbox.com/u/63588663/FeaRecoveryV1.4.tar.md5 thanks to nail16]
You have to flash only FeaMod v1.2 (you need not more than that) therefore you need odin and AriesVE - links at the bottom of this thread. (you need them also for the next step)
To get your Phone into downloading mode you have to shut it down and press power volume down and home at the same time. After 5 seconds you see a nice downloading picture.
After flashing sucessfully you can make your fist backup (chose backup to internal card -it is faster)
3) new ROM (easy when you succeed with the last step) http://forum.xda-developers.com/showthread.php?t=1533029 [ROM] I9001XXKQ7 [Android 2.3.6] thanks to mozgoder
Same procedure as before. You have to flash it by downloading mode.
Now you have a odexed KQ7 ROM (you need something like that for step 5) -and a nice lockscreen!
3a) root it (point 1 again) and install busybox installer from the market (I am not sure, if it is necessary, but you will need it later)
4) deodex your ROM (easy) - this step is required for installing additional themes etc. you can install it by recovery - that means, you have to copy the file to (internal) sdcard and choose this file by recovery: thanks to crybert http://forum.xda-developers.com/showpost.php?p=23321508&postcount=24
(or try this link http://www.mediafire.com/?mjabvv2loub3z35 )
wow, now you have a brilliant deodexed ROM! If everything went fine this far all apps and datas are still where they should be.
Make a backup!
5) now its getting vibrant - you can beginn modding your phone.
[TOOL] - Galaxy S Plus Configurator BETA 5 thanks to broodplank1337 [EDIT It will work on all recent deodexed roms (xxkps till xxkq7)]
http://forum.xda-developers.com/showthread.php?t=1466056
A great tool! Download it, start it, try it. It tells you what to do - so please read the text and do it that way - no error occured to me.
Start with kernel, then accelerator and so on. Make your choice. [EDIT your ROM has now an Antutu (benchmark tool) score of about 3600 -for example with feacore 1.4 1,8 GHz, UNiversal adrenaline shot 13 and sio I/O SCheduler you get about 4360 points!]
There is also an option for boot loops - I did not try it, but have it in mind, in case of..
So, now you have your phone as you like it - good luck and have fun!
can we please have this as a sticky... will prevent a lot of newbies asking questions regarding this... its simple and easy instructions... thanks
p.s. its in the wrong section (should be in general)... but it might get lost in the "I9000 jungle" so i dont mind it being here
lioncc could you please proof the links. I get a 404 error.
thanks crybert - now it should work
tq..
now i can teach my friends using this tutorial..
its hard to teach blindly via facebook..tq very much.
Thanks for posting my configurator
Thanks for the thread.... this is very much helpful for noobs like me to tweak and understand our device cheers to you bro!
---------- Post added at 09:13 AM ---------- Previous post was at 08:47 AM ----------
lioncc said:
well, I own the 9001 now for 4 days, had a lot of boot loops, recoveries and am finally satisfied - I want to show you an easy way to get there faster:
1) root (easy) http://forum.xda-developers.com/showthread.php?t=1253707
thanks to KeksKlip - (to get into recovery you need to shut off, press Volume up and Power until Samsung appears, then wait for the box and press menu)
2) recovery (not so easy) - you will be happy to have a backup, so this is really wise to install it. The recovery from RomManager does not work - you have to install this modded recovery.
http://forum.xda-developers.com/showthread.php?t=1331164 [Release]FeaMod Recovery 1.4 - based on CWM Recovery v. 5.5.0.4. thanks to manveru0
You have to flash only FeaMod v1.2 (you need not more than that) therefore you need odin and AriesVE - links at the bottom of this thread. (you need them also for the next step)
To get your Phone into downloading mode you have to shut it down and press power volume down and home at the same time. After 5 seconds you see a nice downloading picture.
After flashing sucessfully you can make your fist backup (chose backup to internal card -it is faster)
3) new ROM (easy when you succeed with the last step) http://forum.xda-developers.com/showthread.php?t=1533029 [ROM] I9001XXKQ7 [Android 2.3.6] thanks to mozgoder
Same procedure as before. You have to flash it by downloading mode.
Now you have a odexed KQ7 ROM (you need something like that for step 5) -and a nice lockscreen!
3a) root it (point 1 again) and install busybox installer from the market (I am not sure, if it is necessary, but you will need it later)
4) deodex your ROM (easy) - this step is required for installing additional themes etc. you can install it by recovery - that means, you have to copy the file to (internal) sdcard and choose this file by recovery: thanks to crybert http://forum.xda-developers.com/showpost.php?p=23321508&postcount=24
(or try this link http://www.mediafire.com/?mjabvv2loub3z35 )
wow, now you have a brilliant deodexed ROM! If everything went fine this far all apps and datas are still where they should be.
Make a backup!
5) now its getting vibrant - you can beginn modding your phone.
[TOOL] - Galaxy S Plus Configurator BETA 5 thanks to broodplank1337
http://forum.xda-developers.com/showthread.php?t=1466056
A great tool! Download it, start it, try it. It tells you what to do - so please read the text and do it that way - no error occured to me.
Start with kernel, then accelerator and so on. Make your choice.
There is also an option for boot loops - I did not try it, but have it in mind, in case of..
So, now you have your phone as you like it - good luck and have fun!
Click to expand...
Click to collapse
question on the S Plus configurator... will it work on stock deodexed rom? I thought its for broodrom?
rykn21x said:
Thanks for the thread.... this is very much helpful for noobs like me to tweak and understand our device cheers to you bro!
---------- Post added at 09:13 AM ---------- Previous post was at 08:47 AM ----------
question on the S Plus configurator... will it work on stock deodexed rom? I thought its for broodrom?
Click to expand...
Click to collapse
It will work on all recent deodexed roms (xxkps till xxkq7)
excluding zskp6/zskp7
From now on you can flash Feacore Recovery v1.4 directly from odin, no need to flash v1.2, check the feacore thread.
here's the link for v1.4 odin i'ts only the recovery no kernel http://dl.dropbox.com/u/63588663/FeaRecoveryV1.4.tar.md5
nail16 said:
From now on you can flash Feacore Recovery v1.4 directly from odin, no need to flash v1.2, check the feacore thread.
here's the link for v1.4 odin i'ts only the recovery not kernel http://dl.dropbox.com/u/63588663/FeaModRecovery_1.4.tar.md5
Click to expand...
Click to collapse
There kernel 136!!?
I put the kernel changes!!
I don't understand ?
!!!
Unpack the tar There a kernel!?
alexyuh said:
Unpack the tar There a kernel!?
Click to expand...
Click to collapse
Yes that's a stock kernel
just flash the .md5 file with odin
???
how to flash without the kernel?
FeaMod 1.4? just flash the .md5 file with odin
Here use this it's only the recovery http://dl.dropbox.com/u/63588663/FeaRecoveryV1.4.tar.md5
thanks broodplank1337 and nail16 - I include your comments into the first post
hi i use kq7 stock rom and for me is very stable original kernel, root, deodex, tw4launcher, extenderbar. i wont change my phone keypad(original keypad green) whit ics phone (keypad black and cyan) is possible. What should I do? thanks for reply bye
Its gr8 to see such topic nd discussion friends i m glad to be a part here in xda wid u all dev
Sent from my GT-I9001 using XDA Premium App
Im running XXKQ7 stock rom (rooted) and have installed FeaMod recovery. If i understand correctly i need just to download that zip with deodexed rom and flash it via recovery? Should I wipe data/factory reset before flashin it?
No you don't have to wipe data but wiping cache would be good
deodexed rom include deodexed apps and framework so these don't effect you'r rom data cause data is a seperate partition anyways
you can also do this manually using adb
Please i need your help about :
my phone is samsung galaxy i9003
my software now is jelly bean 4.1.2
I need to update my phoen to jb 4.2.2
can any one help me ??
i posted this thread in Q and A and no one help me
Please i need help
all i need to update my phone from android 4.1.2 to 4.2.2
please help me
Thanks ,,,
Hey bro follow this to make clean install (but this will wipe your data)
DO IT AT YOUR OWN RISK
1- make sure you have kies installed or just install galaxy sl usb drivers (thanks to Zulfauzi).
2-Download odin3 v1.85 from the attachments.
3-Download full DDLF2 from here (thanks to (thanks to sgatechwork).
4. Run Odin3 v1.85.
5. Check Re-Partition, Auto Reboot and F. Reset Time.
6. Click PIT button and select this file: latona_20110114.pit
7. Set it to download mode : Press Volume down + OK first, then hold Power button.
8. Connect USB cable and the program will detect the phone's Com number.
9. Click Start button to download the PIT file to phone.
10. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir].
11. Click PDA button and select this file: CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
12. Click PHONE button and select this file: MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5.
13. Click BOOTLOADER button and select this file: APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
14. Click CSC button and select this file: GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5.
15: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!].
16. Click Start button to flash these files to phone.
17. Do not touch anything till you see PASS on the program window.
18. Factory reset.
19. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
thanks to Misledz for the instructions (original thread here)(I only edited file names).
Now download any Jb 4.2.2 rom and carefully follow the OP instructions.
I suggest CM10.1 A8 by dhiru1602 (thanks to him), rom is verry stable and smooth.
if I helped you please hit the "thanks" button
Best regards
ASMI1 said:
Hey bro follow this to make clean install (but this will wipe your data)
DO IT AT YOUR OWN RISK
1- make sure you have kies installed or just install galaxy sl usb drivers (thanks to Zulfauzi).
2-Download odin3 v1.85 from the attachments.
3-Download full DDLF2 from here (thanks to (thanks to sgatechwork).
4. Run Odin3 v1.85.
5. Check Re-Partition, Auto Reboot and F. Reset Time.
6. Click PIT button and select this file: latona_20110114.pit
7. Set it to download mode : Press Volume down + OK first, then hold Power button.
8. Connect USB cable and the program will detect the phone's Com number.
9. Click Start button to download the PIT file to phone.
10. After it is Done Click on Reset button [Partition box should be unchecked automatically - Thanks to jaskir].
11. Click PDA button and select this file: CODE_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
12. Click PHONE button and select this file: MODEM_I9003DDLE1_REV_00_CL1149304.tar.md5.
13. Click BOOTLOADER button and select this file: APBOOT_I9003DDLF2_CL1153545_REV08_user_low_ship.tar.md5.
14. Click CSC button and select this file: GT-I9003-MULTI-CSC-ODDLF2_RST.tar.md5.
15: You should unplug usb cable, remove battery, insert battery and bring it back to download mode. I have never been able to bring it to download mode with usb plugged in. [Thanks to jaskir for this suggestion to make it clear to new users!].
16. Click Start button to flash these files to phone.
17. Do not touch anything till you see PASS on the program window.
18. Factory reset.
19. [To fix issues that pertain] Reflash from steps 9 -15 again, No need of latona at this point.
thanks to Misledz for the instructions (original thread here)(I only edited file names).
Now download any Jb 4.2.2 rom and carefully follow the OP instructions.
I suggest CM10.1 A8 by dhiru1602 (thanks to him), rom is verry stable and smooth.
if I helped you please hit the "thanks" button
Best regards
Click to expand...
Click to collapse
Thanks for your reply
but there's another method about updating by CWM RECOVERY
do you know how this method done ?
dr_amjad said:
Thanks for your reply
but there's another method about updating by CWM RECOVERY
do you know how this method done ?
Click to expand...
Click to collapse
yes there is another way if you have recovery installed. Just tell us what ROM you are on (your 4.1.2 ROM name) and try to find out if you have CWM recovery(volume up+home+power). Let us know this this then we will proceed.
@ASMI1 :He is on a 4.1.2 OS means he have a custom ROM and re-partioning is not mandatory because he is comming for a CM10 base.
mustafahussain said:
yes there is another way if you have recovery installed. Just tell us what ROM you are on (your 4.1.2 ROM name) and try to find out if you have CWM recovery(volume up+home+power). Let us know this this then we will proceed.
@ASMI1 :He is on a 4.1.2 OS means he have a custom ROM and re-partioning is not mandatory because he is comming for a CM10 base.
Click to expand...
Click to collapse
Thank you very much mr mustafa
i download the ROM from video on youtube and this is link of video
http://www.youtube.com/watch?v=VqypSD3JBJk
It's CM 10 Alpha 3
And in the video there's a download link of the Rom and this is the link which in the video
http://forum.xda-developers.com/showthread.php?t=1868074
by the way : when i click power key there is an option called : Reboot
when i click on Reboot tell me that i can Reboot my phone and recovery and download mode
Thanks for your reply
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Drizzt_Kueh said:
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Click to expand...
Click to collapse
Thank you very much for your reply
i will try and tell you
but i will not do any thing about : Data wipe/Factory reset & 5. Format dbdata. , right ??
Drizzt_Kueh said:
If you like the jelly bean 4.1.2 (CM10) by Dhiru, surely you'll like the CM10.1 version.
It is in here. Review it for more details.
You will need the latest CM10.1 in Dhiru1602's downloads and this gapps..
Download both on the SD card. Then, basically this will be the instructions to install it:
Code:
Upgrading from previous versions of CM10
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
PD: By the way, you can use the Reboot -> Reboot to recovery option you've mentioned.
Click to expand...
Click to collapse
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
dr_amjad said:
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
Click to expand...
Click to collapse
Redownload rom.
Sent from my GT-I9003 using xda premium
dr_amjad said:
I tried it
When i choose zip from sdcard and choose the rom tell me :
Installing : /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip
Finding Update package ....
opening update package ....
E: Can't open / /sdcard/others/Cm10.1-Galaxy SL - JDQ39E-Alpha8.zip ( bad )
Installation aborted
What can i do ??
Click to expand...
Click to collapse
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
dr_amjad said:
Thank you very much mr mustafa
i download the ROM from video on youtube and this is link of video
http://www.youtube.com/watch?v=VqypSD3JBJk
It's CM 10 Alpha 3
And in the video there's a download link of the Rom and this is the link which in the video
http://forum.xda-developers.com/showthread.php?t=1868074
by the way : when i click power key there is an option called : Reboot
when i click on Reboot tell me that i can Reboot my phone and recovery and download mode
Thanks for your reply
Click to expand...
Click to collapse
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
How to install
Warning only for lasted base CM10 Alpha4
if older base CM10 Alpha3 Full KPE please !!!
- Wip Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Flash first clean for mandatory starting
On CM10 Alpha 3 and all other basic Froyo, Gingerbread, ICS, JB
Click to expand...
Click to collapse
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
ASMI1 said:
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
Click to expand...
Click to collapse
Thank you very much mr ASMI 1 for your reply
but sorry i am still Noob in android development and updating
but according to your reply i must do :
- Wip Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Right ??
and please is there a video about my case (( updating samsung gt i 9003 from cm 10 alpha 3 to cm 10.1 alpha 8 )) ??
and sorry for annoyance you
ASMI1 said:
try to remove the rom zip from sdcard and copy it again from pc, this worked for me when I tried to install slim CM 7 by TheFrankenstain (here the thread if you wanted to try it..rom link here)(You rom is awesome TheFrankenstain...thank you)
If this didn't work then try to redownload the rom (don't use your phone to download roms...bad idea).
to make sure rom's archive is not corrupted, check you rom MD5 sum (Dev-Host server provide the correct MD5)
HashCheck is a good tool for this.
---------- Post added at 09:52 PM ---------- Previous post was at 09:29 PM ----------
BE CAREFUL...You can only update to CM10.1 rom (or any other rom based on CM10.1) only if you have CM10 Alpha4 rom (or any other rom based on CM10 Alpha4)
But in your case (you have CM10 A3), you have to follow the whole guide mentioned in the second post.
This is what LoLaTiOn said:
................
thread here.
If you are worried about your data make full backup using recovery and you can restore your apps or your full rom at any time...clean Install is always recommended over updating from previous versions.
BTW...I think full Nandroid restore is dangerous due to different partitioning in ICS/JB roms so it's recommended always to reparation using odin and install full firmware again.
Also, any custom rom is rooted and deodexed and has CWM recovery pre-installed.
sorry for my bad english
Click to expand...
Click to collapse
(( if older base CM10 Alpha3 Full KPE please !!! ))
what the meaning of KPE ??
and i must do this ?? (( if older base CM10 Alpha3 Full KPE please !!! ))
dr_amjad said:
(( if older base CM10 Alpha3 Full KPE please !!! ))
what the meaning of KPE ??
and i must do this ?? (( if older base CM10 Alpha3 Full KPE please !!! ))
Click to expand...
Click to collapse
it means that if you have a base older to CM10 Alpha 3 then you should proceed with full KPE,,,
so IF YOUR CURRENT ROM IS ON CM10 Alpha 3 I would suggest just flash CM10 Alpha4 base ROM by Dhiru then,
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
mustafahussain said:
it means that if you have a base older to CM10 Alpha 3 then you should proceed with full KPE,,,
so IF YOUR CURRENT ROM IS ON CM10 Alpha 3 I would suggest just flash CM10 Alpha4 base ROM by Dhiru then,
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
Click to expand...
Click to collapse
Now i have Cm 10 alpha 3
you want me to do these steps :
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
and update my phone to Cm 10alpha 4 or cm 10.1 alpha 8 ?????????
dr_amjad said:
Now i have Cm 10 alpha 3
you want me to do these steps :
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
and update my phone to Cm 10alpha 4 or cm 10.1 alpha 8 ?????????
Click to expand...
Click to collapse
No, to upgrade from previous version of CM10 follow this:
1. Reboot to Recovery.
2. Select the ROM zip from your SD Card and flash.
3. Flash Google Apps.
4. Reboot
Click to expand...
Click to collapse
and then
-Wipe Factory
- Format/system format/emmc
- Flash Carbon and gapps
- Reboot recovery
- Wipe cache and dalvik cache
here where to download CM10 A4 and google apps(20121011 for CyanogenMod 10.0.x) (thanks to master dhiru1602).
BTW, in the past we used to install XXKPE stock rom (pit, bootloader, PDA, Phone, and CSC)(this is what meant by full KPE) and then install DDLF2 as PDA in download mod. But now full DDLF2 is out so we don't need XXKPE anymore to make clean install, you just install full DDLF2 (pit, bootloader, PDA, Phone, and CSC) the same way you install XXKPE and then proceed with installing your custom rom.
it is recommended to make clean install always before installing any custom rom (CM or rom based on CM) to prevent any issue (installing custom rom over another custom rom may cause some problems like lags and no signal issue...etc) just make clean install.
I advise you to upgrade only if, for example; you want to update to REMICS rom and you have previous version of REMICS rom or you want to update to carbon rom and you have previous version of carbon rom or you want to update to CM10.1 A8 rom and you have previous version of CM10.1 A7 rom...Do you get my point?
Hello !
I use a Slimkat ROM weekly 5.8 build 4901 but GPS doesnt works.So I want to downgrade to Nexesque 3.6.Can you explain me the correct way to do it?Do I need RDS?
aleram said:
Hello !
I use a Slimkat ROM weekly 5.8 build 4901 but GPS doesnt works.So I want to downgrade to Nexesque 3.6.Can you explain me the correct way to do it?Do I need RDS?
Click to expand...
Click to collapse
The idk how to read post of the day
Nexesque 3.6 thread http://forum.xda-developers.com/showthread.php?t=2510965
Copy and pasted straight from the first post which you were unable to read
DOWNLOAD LINK (v3.6 November 22, 2013) (KERNEL INCLUDED)
Direct Download Link Here
*changelog and additionally OPTIONAL ADDON for customizing Rom (thanks hallokitty for the step by step guide) in post #2*
DOWNLOAD LINK (v3.5 October 9, 2013) (KERNEL INCLUDED)
Direct Download Link Here
*changelog and additionally OPTIONAL ADDON for customizing Rom (not part of original Nexesque release, thanks hallokitty for the step by step guide) in post #2*
** COMPATIBLE WITH BOTH LOCKED AND UNLOCKED BOOTLOADERS **
TWRP / CWM INSTRUCTIONS:
1. Be rooted and bootloader unlocked with twrp or CWM (Safestrap Users, See post #4)
2. Factory reset
3. Mount System
4. Install ROM
5. Wipe Cache
6. Enjoy
------------------------------------------
Further flashing instructions if required
Try putting file into root of SD card or internal storage. Before performing the full wipe make sure system is mounted as well. And double check system is mounted before flashing. If coming from another Rom make sure it was 4.1.2.
If previous Rom was higher than 4.1.2 then flash this before Nexesque: http://d-h.st/5EV
What is SlimKat? 4.4. What does the paragraph above say? If previous Rom was higher than 4.1.2 then flash this before Nexesque: http://d-h.st/5EV
palmbeach05 said:
The idk how to read post of the day
Nexesque 3.6 thread http://forum.xda-developers.com/showthread.php?t=2510965
Copy and pasted straight from the first post which you were unable to read
DOWNLOAD LINK (v3.6 November 22, 2013) (KERNEL INCLUDED)
Direct Download Link Here
*changelog and additionally OPTIONAL ADDON for customizing Rom (thanks hallokitty for the step by step guide) in post #2*
DOWNLOAD LINK (v3.5 October 9, 2013) (KERNEL INCLUDED)
Direct Download Link Here
*changelog and additionally OPTIONAL ADDON for customizing Rom (not part of original Nexesque release, thanks hallokitty for the step by step guide) in post #2*
** COMPATIBLE WITH BOTH LOCKED AND UNLOCKED BOOTLOADERS **
TWRP / CWM INSTRUCTIONS:
1. Be rooted and bootloader unlocked with twrp or CWM (Safestrap Users, See post #4)
2. Factory reset
3. Mount System
4. Install ROM
5. Wipe Cache
6. Enjoy
------------------------------------------
Further flashing instructions if required
Try putting file into root of SD card or internal storage. Before performing the full wipe make sure system is mounted as well. And double check system is mounted before flashing. If coming from another Rom make sure it was 4.1.2.
If previous Rom was higher than 4.1.2 then flash this before Nexesque: http://d-h.st/5EV
What is SlimKat? 4.4. What does the paragraph above say? If previous Rom was higher than 4.1.2 then flash this before Nexesque: http://d-h.st/5EV
Click to expand...
Click to collapse
I already tried to flash boot.IMG but I got the phone stuck on M logo.Then I reboot on recovery and reinstalled Slimkat 4.4... if you are so gentile to suggest any other solutions is better than tell me I am unable to read post.I have read all....
aleram said:
I already tried to flash boot.IMG but I got the phone stuck on M logo.Then I reboot on recovery and reinstalled Slimkat 4.4... if you are so gentile to suggest any other solutions is better than tell me I am unable to read post.I have read all....
Click to expand...
Click to collapse
did you flash that, then flash the ROM before heading back to SlimKat?
palmbeach05 said:
did you flash that, then flash the ROM before heading back to SlimKat?
Click to expand...
Click to collapse
Yes...when I have installed the rom I read the message status 7 installation aborted set_perm ....I checked file updater script in meta inf...I formatted system data cache then mounted all and flashed the ROM bit nothing...
resolved changing philz touch recovery to cwm 6.0.4.4 with flashify...bit the signal line is off.Already patched to enable full GSM functions....any idea?
What's inside?
1. BASE ON MIUI 4.8.15 [JB 4.2.2]
2. MIUI Framework and other System Apps
3. MIUI Xiaomi Bootanimation
4. Debloated
5. Deodexed
6. Prerooted
7. Busybox Installed
8. init.D support
9. Feel FREE to EXPLORE...
====================================================
Download Link:
1. A680_MIUIV2.zip + Camera Patch.zip
====================================================
Flashing Instruction:
1. Go to TWRP/CWM
2. Do a Factory Reset
3. Flash A680_MIUIV2.zip
4. Wipe Dalvik and Reboot
5. Enjoy!
====================================================
Thanks to:
XDA
August D.
W500 Titan Family
Lenovo A680 Legit Users
lastkenji said:
What's inside?
1. BASE ON MIUI 4.8.15 [JB 4.2.2]
2. MIUI Framework and other System Apps
3. MIUI Xiaomi Bootanimation
4. Debloated
5. Deodexed
6. Prerooted
7. Busybox Installed
8. init.D support
9. Feel FREE to EXPLORE...
====================================================
Download Link:
1. A680_MIUIV2.zip + Camera Patch.zip
====================================================
Flashing Instruction:
1. Go to TWRP/CWM
2. Do a Factory Reset
3. Flash A680_MIUIV2.zip
4. Wipe Dalvik and Reboot
5. Enjoy!
====================================================
Thanks to:
XDA
August D.
W500 Titan Family
Lenovo A680 Legit Users
Click to expand...
Click to collapse
Can be used as a daily driver ?
Tre91 said:
Can be used as a daily driver ?
Click to expand...
Click to collapse
What do u mean bro?
Just try it, you can always make a backup of your stock rom..
Not booting
I installed MIUI in my phone (Lenovo a680) using ROM Manager. After booting my phone it didn't open again. It's been a day. Your response is much appreciated.
Hope this works for you....
Awesomeshocker said:
I installed MIUI in my phone (Lenovo a680) using ROM Manager. After booting my phone it didn't open again. It's been a day. Your response is much appreciated.
Click to expand...
Click to collapse
Try searching this post on blogspot and see how to do it.
lenovoa680transcrypto.blogspot.in
Could you create a lollipop rom for this device
Please
I BEG YOU
Unable to download the zip file.. the file appearing is a text file with same name but having 280b size only... please help..
Cyanogenmod 12.1 Custom Rom (Unofficial) 100% Bugless
Device Name: Huawei Y3ii LUA-U22, (3G Model)
Chipset: Mt6582,
Kernel: 3.10.72,
Android Version: 5.1
ROM Download Here
___For Preview image click the link beow.-------------
https://drive.google.*com/open?id=1P5chJdDsf2USsLjc8X7r7b8_mB7tIIxM
https://drive.google.*com/open?id=1x0nI4omhIGjcvXwNLFP76nS-hMaCWR03
https://drive.google.*com/open?id=1oQ2ruQEGDETkthz_HHQ9U74zInHkG2t2
https://drive.google.*com/open?id=10Cq3kYKHyNemTank5yaQEHtpmq3UjAVw
https://drive.google.*com/open?id=1QRT29O7dxcIvitwCWiwsNGUc71tgiCSk
------------------------------------------------------------------------------------------------------
++++ For Live Preview Click here
Features Of This Rom:
You can download and flash this rom with any recovery without any error.
-------------------------------------------------------------------------------------------------
It is 100% Bugless Rom
This rom provides you multi boot system
This Rom working for Both Dual Sim & Strong Network Connection.
Long Battery Life
Fast Charging.
Support Audio FX ( That Means Increase You Sound System )
You can record your screen with screencast.
How To Flash This Rom:
1. Wipe Data, cache, Delvik Cache
2. Select Cyanogenmod 12.1 ZIP file from Your SD Card
3. Install The Zip File
4. Flash the GAAps (This time don't wipe anything)
[Note: Download the Gaaps form the link. The gapps should be 5.1 , For all apps select-stock, For few apps select- Nano]
5. Flash the Supersu.zip file beacuse the rom is not pre-rooted.
-------------------------------------------------------------------------------------------------------
[Note: I have Using CTR Recovery For Flashing This Rom]-- If You need the CTR Recovery Then Download Here
-------------------------------------------------------------------------------------------
For More Update please like and share my post. If you face any problem comments below i will answer and solve your problem.
sujon3903 said:
Cyanogenmod 12.1 Custom Rom (Unofficial) 100% Bugless
Device Name: Huawei Y3ii LUA-U22, (3G Model)
Chipset: Mt6582,
Kernel: 3.10.72,
Android Version: 5.1
ROM Download Here
___For Preview image click the link beow.-------------
https://drive.google.*com/open?id=1P5chJdDsf2USsLjc8X7r7b8_mB7tIIxM
https://drive.google.*com/open?id=1x0nI4omhIGjcvXwNLFP76nS-hMaCWR03
https://drive.google.*com/open?id=1oQ2ruQEGDETkthz_HHQ9U74zInHkG2t2
https://drive.google.*com/open?id=10Cq3kYKHyNemTank5yaQEHtpmq3UjAVw
https://drive.google.*com/open?id=1QRT29O7dxcIvitwCWiwsNGUc71tgiCSk
------------------------------------------------------------------------------------------------------
++++ For Live Preview Click here
Features Of This Rom:
You can download and flash this rom with any recovery without any error.
-------------------------------------------------------------------------------------------------
It is 100% Bugless Rom
This rom provides you multi boot system
This Rom working for Both Dual Sim & Strong Network Connection.
Long Battery Life
Fast Charging.
Support Audio FX ( That Means Increase You Sound System )
You can record your screen with screencast.
How To Flash This Rom:
1. Wipe Data, cache, Delvik Cache
2. Select Cyanogenmod 12.1 ZIP file from Your SD Card
3. Install The Zip File
4. Flash the GAAps (This time don't wipe anything)
[Note: Download the Gaaps form the link. The gapps should be 5.1 , For all apps select-stock, For few apps select- Nano]
5. Flash the Supersu.zip file beacuse the rom is not pre-rooted.
-------------------------------------------------------------------------------------------------------
[Note: I have Using CTR Recovery For Flashing This Rom]-- If You need the CTR Recovery Then Download Here
-------------------------------------------------------------------------------------------
For More Update please like and share my post. If you face any problem comments below i will answer and solve your problem.
Click to expand...
Click to collapse
Nice one, Man. If you need some help, I am here.
Does this work on LUA-U23?
DiegoxG said:
Does this work on LUA-U23?
Click to expand...
Click to collapse
This ROM, is developed by dev on android latino org. So you can ask the dev, Does this ROM can be used on U23.
Most of system apps have disappeared, clock bluetooth and others any reasom why ?
viper7144 said:
Most of system apps have disappeared, clock bluetooth and others any reasom why ?
Click to expand...
Click to collapse
Can you give screenshot and logcat?
will this remove huawei apps like huawei backup??
drkpntr said:
will this remove huawei apps like huawei backup??
Click to expand...
Click to collapse
Well, Installing custom ROM will remove official features like cloud storage, device account, system data, and user data.
but is it possible to install them again once a custom rom is applied? because i use huawei back up to save all my data.
drkpntr said:
but is it possible to install them again once a custom rom is applied? because i use huawei back up to save all my data.
Click to expand...
Click to collapse
I think huawei backup will not work properly, because Huawei system use huaweisdk and sync data to account. If you do that, the apps will force close, because Not all custom ROM have same process. Example, you are installing huawei backup, This mean the huawei backup cant work properly(force close) or else. You need a SDK to run huawei system apps. (Like MIUI from Xiaomi)
---------- Post added at 10:50 AM ---------- Previous post was at 10:45 AM ----------
If you want to try please backup your data and system. And Try to install huawei backup. if the apps force close. You can go back to your previous ROM
hi.i got problem to flash CM12.1 UNOFFICIAL LUA-U22.zip.trying to update from sd but suddenly "update abort" appear.maybe got wrong step.should i put on exclusive folder like dload or update or something thx in advance
pojunkampar said:
hi.i got problem to flash CM12.1 UNOFFICIAL LUA-U22.zip.trying to update from sd but suddenly "update abort" appear.maybe got wrong step.should i put on exclusive folder like dload or update or something thx in advance
Click to expand...
Click to collapse
Quick question :
1. Did you install it using Philz or CWM?
2. Did you mean CM12 is ota update?
Reed_405 said:
Quick question :
1. Did you install it using Philz or CWM?
2. Did you mean CM12 is ota update?
Click to expand...
Click to collapse
not really sure ur question .i'm newbie on this.what i do is off my phone and push volume up and power button to enter recovery mode.so there was i clean data and try to flash this zip.so i got problem there while to update from SD.
did i do wrong?should i do flashtool on PC instead?ty for reply :good:
pojunkampar said:
not really sure ur question .i'm newbie on this.what i do is off my phone and push volume up and power button to enter recovery mode.so there was i clean data and try to flash this zip.so i got problem there while to update from SD.
did i do wrong?should i do flashtool on PC instead?ty for reply :good:
Click to expand...
Click to collapse
Before trying to install this ROM, you must follow the order first.
1. Unlock Bootloader
2. Installing Philz/CWM/TWRP
3. Do wipe
4. Install the ROM, SuperSU, and other stuff
5. Reboot system
6. Wait 5-10 minutes
7. Enjoy
Why is my phone stuck on start after flashing the Rom .
Sandip Rai said:
Why is my phone stuck on start after flashing the Rom .
Click to expand...
Click to collapse
Have you follow the instruction?
The link is down.... Anyone please give new download link
aroien said:
The link is down.... Anyone please give new download link
Click to expand...
Click to collapse
Okay, since the owner didnt active to reply this message. So I would like to say that this is like disbanded. If I have time I ll give the link. Please wait.
Link not Working
Link not Working
Download Link.........
Cyanogenmod 12.1 Custom Rom please give me the download link..