Related
Flash Moto Droid to Cricket / Metro full apps, web,mms.
This is my attempt to recreate the solution from Howard Forums
i may have missed a few steps along the way but here it goes. as of 08/02/2010 - make directory now for 2.2 roms
FILES FOR FLASHING TO CRICKET (U2nl,PRL's,Autostart,SPRecovery,NV items)
Special thanks and credit should go to
SyZtyM (i recreated his thred for XDA)
gijoey1980
Tracphonejunkie
whiterabittorg
To0
Insaincain (For the nv items. You are a legend, and credit is due where credit is due**AS read from SyZtyM)
Admin (For all sites. PERIOD)
You will need:
1. CDMA WS 2.7 (google)
2.Harware Virtural Serial Port this is the demo good for 14days
3. Motorola A855 USB drivers (These are the 32bit Drivers)
4. Cyanogen Mod Rom from Rom Manager in market
5. SPRecovery
6&7.Autostart.sh & U2nl from whitrabbit.org (thanks to whiterabbit). Save autostart.sh and U2nl in C:\android\tools\.
8.download Autostart (Root) from Market
9. NV items from http://www.whiterabbit.org/android (u must generate this uniquely with you [email protected] i have included a generated [email protected] for sample or to replace x's with you MDN
Step 1. First step is to make sure you have the drivers installed on your computer, and you also need to have Android SDK installed on your computer.
You will need to root the phone, key here is to make sure the kernel you load supports iptables.
Step 2. if you need to ROOT: follow the guide
than download Rom manager over wifi from MARKET, proceed to flash clockwork and download and install cyanogen 5.xx rom, and google apps..wipe data etc.
Step 2.1 if first fails. get RSD Lite 4.6 (google), Power on phone holding down the up arrow and pressing power, this will put you into bootloader mode.
Open RSD Lite 4.6
Flash the SPRecovery_ESE81.sbf file with RSD Lite.
this should just flash the recovery if not download a rom like SMOKEDGLASS unzip and put in folder on SD named Nandroid
Once the phone is completely rebooted into rooted android, power it off.
alternately u can install BuglessBeast froyo v 02.1 from alldroid.org then skip to these steps below
Hold down “T” on the keypad and power on phone.
Plug into computer and open HW Virtual Serial Port (your drivers should install and connect etc)
In HWVS set the IP address to 192.168.16.2 and the port to 11008, choose the com port 10 click connect. (For this tutorial we will use COM10)
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
On security tab send SPC 000000. (msg says phone accepts blah blah blah
Go to tab labeled “Other” and write prl. For Cricket EVDO, 6499(new service plan) and 38515 is recommended.
Go to NAM and enter MIN ex. 615-555-5593 (usually different from your actual phone# and MDN(your mobile number ex. 615-555-5551 and click write.
Goto “Memory” tab and click write under NV items, find the downloaded NV items you got from here
for example you must generate the NV items by inputing your MDN([email protected]). box opens telling you to save them as .txt and select them with cdma 2.7. (Thanks again to insanecain)
It should then say, 12 NV items were successfully written to phone.
Go to Main tab and click mode reset.
You can now close HWVS and CDMA WS and open cmd.exe on your computer.
if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone
Once phone reboots go to the market using WI-FI and download and install Autostart root required
Open the Voice Dialer on the phone and say “Open APNs” and click open.
Click on the Verizon and edit everything to match below:
Name - Cricket
APN internet
Proxy wap.mycricket.com:8080
Port 8080
Username [email protected]
Password cricket
Server wap.mycricket.com
MMSC http://mms.mycricket.com/servlets/mms
MMS Proxy wap.mycricket.com
MMS Port 8080
MCC 310
MNC 004
Authentication Type PAP or CHAP
APN type <Not set>
Now click the menu button and click Save.
Before starting the next step make sure you have the u2nl file in your this folder c:/android/tools and also that you have you autostart.sh file in this folder c:/
Now go to command prompt and type the following commands,
cd c:\android\tools
adb shell
mkdir /data/opt/
exit
adb remount
adb push c:\android\tools\u2nl /system/bin/u2nl
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
chmod 0755 /system/bin/u2nl
chmod 0755 /data/opt/autostart.sh
adb reboot
Now, once your phone has rebooted, you should have working web, mms, app, gps, and all. If you don’t go back and check all the steps to insure you did everything exactly right.
thanks everyone for reading.
i would also like to thank everyone who helped give back to the droid community by solving this, (I gave up and switched back to my eris for full support like a Beeach! which i bricked twice) im back on DROID baby
currently running BuglessBeast Froyo v 02.1 and the p3 1000 kernel.
quadrant score: 972
this is a very good set up thanks for the post!
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
Click to expand...
Click to collapse
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
broken linkkkkkkzzzzzzzzzzzzzzzzzzzz
"the guide" http://rootyourdroid.info/guides/obtaining-root/
Click to expand...
Click to collapse
is a broken link : (
ummm...flashed new rom...now no web,mms
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
i have a motorola droid on metropcs help me please awwwwwww!!!!
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
somebody hit me up with the info
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
fredline12002 said:
is a broken link : (
Click to expand...
Click to collapse
not sure whats up with the link, just google a new how to root, sorry
Geniusdog254 said:
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
Click to expand...
Click to collapse
when u open HV serial Port, its the second to last or maybe last tab,,, you cant miss it. this is where u make sure NV Enabled is NOT selected
Wolfdragon said:
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
Click to expand...
Click to collapse
If your on 2.1 bugless you need to redo allthe steps for fully working rom, maybe for 2.2 also i havent had to for a while, only bcuz i have cricket and roam off metro.
luvjones305 said:
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
Click to expand...
Click to collapse
you need to be more specific with wat u deleted?? which rom u ran? etc where did u get it flashed? most likey u went to a metro dealer, to get it flashed, METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around.
luvjones305 said:
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
Click to expand...
Click to collapse
what market are you in? who flashed your phone? quoted from above "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "
Metro Fix Web/mms
"[/QUOTE] "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "[/QUOTE]
For anyone having trouble with MMs/web on METRO please check out this thread. read from pg one if you dont know whats going on. or pick up here if you can perform the web/mms work around.
http://www.howardforums.com/showthread.php/1656326-Phones-and-more-info/page11
Grr
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
................... bump
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
iNFiNiTY125 said:
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
Click to expand...
Click to collapse
from my understanding, cdma networks calls and text dont go through data connections, so when u place a call it will switch only to bars and no 1x/3g.
MMS and web will only work when not connected to a call ( i think thats what your stating??) ive never had a problem with data connection not coming back to phone after a call.... hopefully i answered your questions? and gps shouldnt be bothered at all that may be a rom issue. try a few roms other that bugless beast thats basically a stock ROM look into lithium mod or Chevyno1
tko1 said:
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
Click to expand...
Click to collapse
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
dortega2388 said:
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
Click to expand...
Click to collapse
you should be fine with the NV items. after you flash 2.2 dial 611 (you may need to reflash PRL, and then from there i would give your phone about a 2minutes to see if any 1x/3g show up. if not commence with the instructions lol.
bigslanki said:
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
Click to expand...
Click to collapse
thanks for the reply, well i had all but given up on my droid dreams and i figured out on my own that they were QPST directions but were missing this important piece. QPST 2.7 WITH A OLDER BUILD LIKE 264 WILL NOT CONFIGURE THE DROID,IT GIVES AND ONLINE ERROR. YOU SHOULD USE AN UPDATED VERSION. I ENDED UP FINDING 2.7 BUILD 323.
Also. its unclear as to why in the adb commands we have
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
it may be obvious to some but if Now: is an actual command it wouldnt work. so im assuming it isnt, and pretty much adb after that point is irreconcilable.
no matter what the droid never left the verizon network needless to say, and i havent recieved any input as to where i could have gone wrong, everything else was flawless up until the Now: part basically then i had to piece together adb. even tried without the now part and didnt succeed.
i did this and everything works. only problems is it 1x all the time; how to i get 3g?
As the subject says. Anyone know how to extract APN settings from a locked phone? I tried "APN Backup & Restore" but seeing Softbank has locked down the settings part I cant extract info, same goes for "Sbm4GSimInfo", it just returns blank fields.
I need this info as I want to buy a Nexus 5 or HTC One.
Hello from SoCal
I'm mighty impressed with the custom roms I've come across on this amazing site, but after several frustrating days, I've decided to go back to stock firmware for my cdma moto g3, XT1548. (Huge props to lost101 for the detailed and easy-to-follow post.)
It's such a pleasure to extend the life and usability of an older phone by installing custom roms, and I've never had any problems until I bought the g3. But try as I might, no matter what rom I installed, I couldn't restore mobile data.
After installing the rom, it seemed easy enough to complete the final step and reset the carrier by inputting ##72786# via the generic phone app. But it never worked -- instead of going to the SCRTN settings, the dialer treated it like a phone call. I googled around for days, tried changing various settings -- no luck.
Actually, I did manage to upgrade from 5.1 to 6.0 by leaving TextNow for another Sprint mnvo, so it's not a total loss. Sure did like some of the 7.1.2 roms I installed for a bit, though . . .
Did I do something dumb, or is it the case that a certain set of conditions can limit a phone's ability to be upgraded? Any thoughts? Again, LOVE this website. Thanks!
OBTonyD said:
Hello from SoCal
I'm mighty impressed with the custom roms I've come across on this amazing site, but after several frustrating days, I've decided to go back to stock firmware for my cdma moto g3, XT1548. (Huge props to lost101 for the detailed and easy-to-follow post.)
It's such a pleasure to extend the life and usability of an older phone by installing custom roms, and I've never had any problems until I bought the g3. But try as I might, no matter what rom I installed, I couldn't restore mobile data.
After installing the rom, it seemed easy enough to complete the final step and reset the carrier by inputting ##72786# via the generic phone app. But it never worked -- instead of going to the SCRTN settings, the dialer treated it like a phone call. I googled around for days, tried changing various settings -- no luck.
Actually, I did manage to upgrade from 5.1 to 6.0 by leaving TextNow for another Sprint mnvo, so it's not a total loss. Sure did like some of the 7.1.2 roms I installed for a bit, though . . .
Did I do something dumb, or is it the case that a certain set of conditions can limit a phone's ability to be upgraded? Any thoughts? Again, LOVE this website. Thanks!
Click to expand...
Click to collapse
If you're using the Virgin mobile xt1548, you just need to set up the apn correctly. Use the one in the attachments. This how I do it.
1. Clean a flash ROM.
2. Mount /system in TWRP
3. Copy the apn-conf.xml with TWRP's file manager to /system/etc
4. Chmod the apn-conf.xml to 0644
5. Unmount /system and reboot.
6. Open settings and find the cellular network settings. Select the following.
Preferred network type>LTE
System select>Automatic
CDMA subscription>RUIM/SIM
Access Point Names>APN1 Virgin Internet LTE (if there is an APN2 delete it.)
After that select "carrier settings". You'll get an error, all radios will reset and LTE will show up in a few seconds.
For future reference do not use dialer codes on custom Roms for anything network related. This is asking for some serious headaches.
Spaceminer said:
If you're using the Virgin mobile xt1548, you just need to set up the apn correctly. Use the one in the attachments. This how I do it.
1. Clean a flash ROM.
2. Mount /system in TWRP
3. Copy the apn-conf.xml with TWRP's file manager to /system/etc
4. Chmod the apn-conf.xml to 0644
5. Unmount /system and reboot.
6. Open settings and find the cellular network settings. Select the following.
Preferred network type>LTE
System select>Automatic
CDMA subscription>RUIM/SIM
Access Point Names>APN1 Virgin Internet LTE (if there is an APN2 delete it.)
After that select "carrier settings". You'll get an error, all radios will reset and LTE will show up in a few seconds.
For future reference do not use dialer codes on custom Roms for anything network related. This is asking for some serious headaches.
Click to expand...
Click to collapse
Thanks for your post Winchester. I have Sprint, which is cdma. I understand editing the apn settings only works for gsm. I did try it anyway for kicks, no luck.
Oh and thanks for the heads-up about dialer codes on custom roms -- I had not heard that before.
Hello,
I've rooted a few phones, but I don't really do too much with them, I mostly root them to have an easier time transferring all data from one phone to the next, and for being able to use a couple of root apps. Basically, I'm not all that good at this stuff, but I can get by most of the time with enough research and time. I have not been able to find a thread that's been able to help me with this problem, though.
My V20's reception practically fell off the map after rooting it. I've been researching and trying to find a way to flash the modem files that I dumped with LGUP before I rooted it via dirtysanta, but I'm not having any luck. The files don't have an extension, but from what I can gather, they should be image files. I'm not 100% on that because I can't seem to find what file type they actually are, my computer only lists them with the description of "file". I run Windows 7 if that matters.
Anyway, based on what I've found so far, the files I need to flash in order to fix my reception problem are:
modem_COM5
modemst1_COM5
modemst2_COM5
fsg_COM5
I can't get fastboot to work, I'm not sure how to link my phone to a file path on my computer from command terminal so that's not been working for me. I've also tried renaming the files by adding ".img" to the end, zipping them and installing them with twrp afterward, but they won't install, giving me an error of "META-INF/com/google/android/update-binary"
Ultimately, I'm lost. Any help is greatly appreciated, as I've spent hours pouring over threads and trying to fix my stupid reception problems. I have no reception at home, none at work, and I have spotty reception while driving or out in other places, but it's generally terrible. I used to have low reception at home, but I could always make a call if I needed to, and I'd have great reception driving around. Then I rooted my phone and my reception tanked.
platypus25_5 said:
Hello,
I've rooted a few phones, but I don't really do too much with them, I mostly root them to have an easier time transferring all data from one phone to the next, and for being able to use a couple of root apps. Basically, I'm not all that good at this stuff, but I can get by most of the time with enough research and time. I have not been able to find a thread that's been able to help me with this problem, though.
My V20's reception practically fell off the map after rooting it. I've been researching and trying to find a way to flash the modem files that I dumped with LGUP before I rooted it via dirtysanta, but I'm not having any luck. The files don't have an extension, but from what I can gather, they should be image files. I'm not 100% on that because I can't seem to find what file type they actually are, my computer only lists them with the description of "file". I run Windows 7 if that matters.
Anyway, based on what I've found so far, the files I need to flash in order to fix my reception problem are:
modem_COM5
modemst1_COM5
modemst2_COM5
fsg_COM5
I can't get fastboot to work, I'm not sure how to link my phone to a file path on my computer from command terminal so that's not been working for me. I've also tried renaming the files by adding ".img" to the end, zipping them and installing them with twrp afterward, but they won't install, giving me an error of "META-INF/com/google/android/update-binary"
Ultimately, I'm lost. Any help is greatly appreciated, as I've spent hours pouring over threads and trying to fix my stupid reception problems. I have no reception at home, none at work, and I have spotty reception while driving or out in other places, but it's generally terrible. I used to have low reception at home, but I could always make a call if I needed to, and I'd have great reception driving around. Then I rooted my phone and my reception tanked.
Click to expand...
Click to collapse
I can make you a zip to flash the files in TWRP
Sent from my ONEPLUS A6010 using Tapatalk
clsA said:
I can make you a zip to flash the files in TWRP
Sent from my ONEPLUS A6010 using Tapatalk
Click to expand...
Click to collapse
Thanks! Do I just need to email you the modem files?
platypus25_5 said:
Thanks! Do I just need to email you the modem files?
Click to expand...
Click to collapse
no you can put them in the zip below
Here's your zip > https://drive.google.com/open?id=1RiNnyS-iF34a543zQAchi70-YAUvc3hn
rename your files to
modem
modemst1
modemst2
fsg
and add them to the zip and save it
copy to phone and flash it
clsA said:
no you can put them in the zip below
Here's your zip
rename your files to
modem
modemst1
modemst2
fsg
and add them to the zip and save it
copy to phone and flash it
Click to expand...
Click to collapse
I appreciate you making the zip, but after flashing the files my phone won't boot up. When I power it on it says that my device has failed a routine safety check and will not boot. I'm accustomed to my phone saying that when I boot it up, as it's done that ever since rooting it, but then it shows the LG logo and then shuts off and will not turn on again unless I take the battery out and reinsert it. I have to go through that process at least 2 or 3 times to get the phone to load up. When I got it to load up again, the top bar of my phone said I had no service, which it did not before flashing the files. I've gone back into twrp and tried re-flashing it again to no avail.
If it makes a difference there were two sets of files when I went to flash, even though I only put in one set. I renamed them according to your instructions, and there were one set that just had the file name and .img at the end (like fsg.img) and another set that started with ._ and ends with .img (like ._fsg.img)
Thanks again for taking the time, I really appreciate the help.
platypus25_5 said:
I appreciate you making the zip, but after flashing the files my phone won't boot up. When I power it on it says that my device has failed a routine safety check and will not boot. I'm accustomed to my phone saying that when I boot it up, as it's done that ever since rooting it, but then it shows the LG logo and then shuts off and will not turn on again unless I take the battery out and reinsert it. I have to go through that process at least 2 or 3 times to get the phone to load up. When I got it to load up again, the top bar of my phone said I had no service, which it did not before flashing the files. I've gone back into twrp and tried re-flashing it again to no avail.
If it makes a difference there were two sets of files when I went to flash, even though I only put in one set. I renamed them according to your instructions, and there were one set that just had the file name and .img at the end (like fsg.img) and another set that started with ._ and ends with .img (like ._fsg.img)
Thanks again for taking the time, I really appreciate the help.
Click to expand...
Click to collapse
I tested the zip myself it works as expected.
The unlocked bootloader message has nothing to do with your issue.
What sim card are you using?
What are your apn settings?
What was the last Rom you flashed?
Are you on Oreo?
Sent from my ONEPLUS A6010 using Tapatalk
clsA said:
I tested the zip myself it works as expected.
The unlocked bootloader message has nothing to do with your issue.
What sim card are you using?
What are your apn settings?
What was the last Rom you flashed?
Are you on Oreo?
Sent from my ONEPLUS A6010 using Tapatalk
Click to expand...
Click to collapse
It's a nano sim from at&t, and at&t is my carrier. I doubt it's relevant, but I use a prepaid plan.
My app settings are:
Name: ATT Nextgenphone
APN: nxtgenphone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Authentication type: None
APN type: default,mms,supl,hipri,fota
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
I believe the last ROM I flashed was H91510e_VTR_CA_OP_1205.kdz
Using the DirtySanta method of rooting, I think I flashed that so I could actually root the phone and then updated to another version, possibly. I'll include my software info in case that is helpful.
I'm not on oreo, I'm running nougat
Android version: 7.0
Android security patch level: November 1, 2017
Baseband version: MPSS.TH.2.0.1.c3-00011M8996FAAAANAZM-1.69323.1. 69645.2
Kernel version: 3.18.31
Build number: NRD90M
Software version: H91010r
Security software version: MDF v2.0 Release 4
Thanks again for all of your help.
platypus25_5 said:
It's a nano sim from at&t, and at&t is my carrier. I doubt it's relevant, but I use a prepaid plan.
My app settings are:
Name: ATT Nextgenphone
APN: nxtgenphone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Authentication type: None
APN type: default,mms,supl,hipri,fota
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
I believe the last ROM I flashed was H91510e_VTR_CA_OP_1205.kdz
Using the DirtySanta method of rooting, I think I flashed that so I could actually root the phone and then updated to another version, possibly. I'll include my software info in case that is helpful.
I'm not on oreo, I'm running nougat
Android version: 7.0
Android security patch level: November 1, 2017
Baseband version: MPSS.TH.2.0.1.c3-00011M8996FAAAANAZM-1.69323.1. 69645.2
Kernel version: 3.18.31
Build number: NRD90M
Software version: H91010r
Security software version: MDF v2.0 Release 4
Thanks again for all of your help.
Click to expand...
Click to collapse
Maybe theirs a setting in the Hidden menu that will help
using a build.prop editor (thanks @ezzony)
Change ro.build.target_operator from ATT to OPEN to bring back all the missing Modem_Settings and the ones that were also missing in regular Settings>Mobile Networks. Also reverted to stock icons in status bar.
in the dialer type > *#546368#*910#
then go to Field Test>Modem Settings>Network Mode and set to Automatic
reboot
you can also check that Volte and VoWifi are enabled from the hidden menu Modem settings
Also in Settings>Mobile Network>Network Mode be sure it's set to the top one (GSM/WCDMA/LTE auto)
clsA said:
Maybe theirs a setting in the Hidden menu that will help
using a build.prop editor (thanks @ezzony)
Change ro.build.target_operator from ATT to OPEN to bring back all the missing Modem_Settings and the ones that were also missing in regular Settings>Mobile Networks. Also reverted to stock icons in status bar.
in the dialer type > *#546368#*910#
then go to Field Test>Modem Settings>Network Mode and set to Automatic
reboot
you can also check that Volte and VoWifi are enabled from the hidden menu Modem settings
Also in Settings>Mobile Network>Network Mode be sure it's set to the top one (GSM/WCDMA/LTE auto)
Click to expand...
Click to collapse
I downloaded a build.prop editor and changed the build target operator setting, but I'm not sure what you mean by reverting to stock icons in status bar or how to do that. Which settings were missing in Settings>Mobile Networks?
I got into that other menu, but under field test>modem settings I can choose either engineering mode or PDP setting.
Engineering mode says "modemprotocol" in the top corner, with previous, up, down, and next buttons. Under that it says ITEM_2G: 0
[Serving Cell Information]
ARFCN: 0
FL_Timeout_v: 0
RXLEV: 0
C1: 0
C2: 0
Other pages for engineering mode are for Item HSPA:0 [HSDPA Information], Item_NM [general information], Item_3G: 0 [RRC State and Serving Cell information], Item_LTE: 0 [LTE Information]
PDP settings says ModemProtocol at the top and has options for [0] Set LG Fast Dormancy, [1] APN setting, [2' Block DataRecovery.
VoLTE and VoWifi are enabled in the hidden menu, but I can't access Settings>Mobile Network>Network Mode. I can't figure out how to check the GSM and other options. I can go to Settings>Mobile Networks and then I can go to:
Mobile data - just turns it on or off
Mobile data reminder
Review reminder settings
International data roaming
Disable 2G
Access Point Names
Search for AT&T MicroCell - When I search, none are found
I hope I'm not just throwing too much useless information for you to sift through. I'm just not entirely sure of what all is relevant.
platypus25_5 said:
I downloaded a build.prop editor and changed the build target operator setting, but I'm not sure what you mean by reverting to stock icons in status bar or how to do that. Which settings were missing in Settings>Mobile Networks?
I got into that other menu, but under field test>modem settings I can choose either engineering mode or PDP setting.
Engineering mode says "modemprotocol" in the top corner, with previous, up, down, and next buttons. Under that it says ITEM_2G: 0
[Serving Cell Information]
ARFCN: 0
FL_Timeout_v: 0
RXLEV: 0
C1: 0
C2: 0
Other pages for engineering mode are for Item HSPA:0 [HSDPA Information], Item_NM [general information], Item_3G: 0 [RRC State and Serving Cell information], Item_LTE: 0 [LTE Information]
PDP settings says ModemProtocol at the top and has options for [0] Set LG Fast Dormancy, [1] APN setting, [2' Block DataRecovery.
VoLTE and VoWifi are enabled in the hidden menu, but I can't access Settings>Mobile Network>Network Mode. I can't figure out how to check the GSM and other options. I can go to Settings>Mobile Networks and then I can go to:
Mobile data - just turns it on or off
Mobile data reminder
Review reminder settings
International data roaming
Disable 2G
Access Point Names
Search for AT&T MicroCell - When I search, none are found
I hope I'm not just throwing too much useless information for you to sift through. I'm just not entirely sure of what all is relevant.
Click to expand...
Click to collapse
reboot after build.prop edit
then all the options show up
the icons change on their own as a result of the build prop edit
clsA said:
reboot after build.prop edit
then all the options show up
the icons change on their own as a result of the build prop edit
Click to expand...
Click to collapse
Alright, I've done this, I've also made a few different access point names for att to try and see if any of those have better reception. Nothing's working all that great, but hopefully at least one of them works a little better than what I've been used to.
Currently I still have no reception where I'm used to having one or two bars around the house. I'm not sure if there is anything else to do without opening up the phone and replacing any parts. If there is anything else you can think of that I might try, please let me know.
Do you think that changing the screen would make any difference on reception? I did have to have mine changed shortly after rooting the phone, but I can't really imagine that could be the cause since I still do get occasional reception.
Thanks again for all of your help.
platypus25_5 said:
Alright, I've done this, I've also made a few different access point names for att to try and see if any of those have better reception. Nothing's working all that great, but hopefully at least one of them works a little better than what I've been used to.
Currently I still have no reception where I'm used to having one or two bars around the house. I'm not sure if there is anything else to do without opening up the phone and replacing any parts. If there is anything else you can think of that I might try, please let me know.
Do you think that changing the screen would make any difference on reception? I did have to have mine changed shortly after rooting the phone, but I can't really imagine that could be the cause since I still do get occasional reception.
Thanks again for all of your help.
Click to expand...
Click to collapse
Any hardware change could easily damage the antenna or it may be completely unplugged. Check the tear down video on ifixit
Sent from my ONEPLUS A6010 using Tapatalk
I am having the same problem after following the root guide - no data. I'm on T-Mobile with an ATT phone running H91010r. I installed your modem.bat file with my dumped modem files using twrp, I changed the ATT buildprop to open, rebooted and made sure to select the first auto option. I tried dialing the secret menu number but it gives an error. Zero data. Everything else seems to be working phone. Data worked on stock phone before rooting. Please help!
Classpro said:
I am having the same problem after following the root guide - no data. I'm on T-Mobile with an ATT phone running H91010r. I installed your modem.bat file with my dumped modem files using twrp, I changed the ATT buildprop to open, rebooted and made sure to select the first auto option. I tried dialing the secret menu number but it gives an error. Zero data. Everything else seems to be working phone. Data worked on stock phone before rooting. Please help!
Click to expand...
Click to collapse
it's most likely an APN problem
what do you mean the dialer code did not work ? it works on all H910
When I put in the dialer code and hit call I get "ussd code RUNNING" and then "connection problem or invalid mmi code"
I did get 4g working by reseting the Sim card, so I'm not panicking, but it seems slower than before. APN is off the t-mobile site.
Classpro said:
When I put in the dialer code and hit call I get "ussd code RUNNING" and then "connection problem or invalid mmi code"
I did get 4g working by reseting the Sim card, so I'm not panicking, but it seems slower than before. APN is off the t-mobile site.
Click to expand...
Click to collapse
are you sure you have a H910 ?
the dialer code depends on the Motherboard
*#546368#*910#
see the 910# at the end must match your phone
the Verizon LG V20 VS995 dialer code is disabled > worth reading
The unlocked LG V20 US995 would use dialer code *#546368#*995#
I'm not sure what works with the F800 version
clsA said:
are you sure you have a H910 ?
Click to expand...
Click to collapse
Yes, I'm sure. AT&T version, model number LG-H910. Running rooted software version H91010r.
I have the same problem on 800l entered the menu changing the model 996 at the end, as I understand it, without twrp how can I fix the problem?
Hi,
How can I recover from the settings of my android phone a APN password stored on an existing access point saved on my android Samsung work phone?
My device is not rooted and I cannot install app files outside of google store.
The APN is not readily available on the internet as is work
Appreciate advise on method could use to extract this password from the settings.
Would a backup of the device and then extracting the system directory to discover the apn config file work?
dreambro2 said:
Hi,
How can I recover from the settings of my android phone a APN password stored on an existing access point saved on my android Samsung work phone?
My device is not rooted and I cannot install app files outside of google store.
The APN is not readily available on the internet as is work
Appreciate advise on method could use to extract this password from the settings.
Would a backup of the device and then extracting the system directory to discover the apn config file work?
Click to expand...
Click to collapse
Edit: you should provide more info about the phone and android version if you want help
Thanks,
Its a Galaxy Cover 5 Android Version 11. One UI version 3.1
When go into Connections->Mobile Networks->Access point Names->Select the Apn->
There is a APN password already there and I want to copy this or reveal it.
Is this possible?
Thanks for your help