Related
Flash Moto Droid to Cricket / Metro full apps, web,mms.
This is my attempt to recreate the solution from Howard Forums
i may have missed a few steps along the way but here it goes. as of 08/02/2010 - make directory now for 2.2 roms
FILES FOR FLASHING TO CRICKET (U2nl,PRL's,Autostart,SPRecovery,NV items)
Special thanks and credit should go to
SyZtyM (i recreated his thred for XDA)
gijoey1980
Tracphonejunkie
whiterabittorg
To0
Insaincain (For the nv items. You are a legend, and credit is due where credit is due**AS read from SyZtyM)
Admin (For all sites. PERIOD)
You will need:
1. CDMA WS 2.7 (google)
2.Harware Virtural Serial Port this is the demo good for 14days
3. Motorola A855 USB drivers (These are the 32bit Drivers)
4. Cyanogen Mod Rom from Rom Manager in market
5. SPRecovery
6&7.Autostart.sh & U2nl from whitrabbit.org (thanks to whiterabbit). Save autostart.sh and U2nl in C:\android\tools\.
8.download Autostart (Root) from Market
9. NV items from http://www.whiterabbit.org/android (u must generate this uniquely with you [email protected] i have included a generated [email protected] for sample or to replace x's with you MDN
Step 1. First step is to make sure you have the drivers installed on your computer, and you also need to have Android SDK installed on your computer.
You will need to root the phone, key here is to make sure the kernel you load supports iptables.
Step 2. if you need to ROOT: follow the guide
than download Rom manager over wifi from MARKET, proceed to flash clockwork and download and install cyanogen 5.xx rom, and google apps..wipe data etc.
Step 2.1 if first fails. get RSD Lite 4.6 (google), Power on phone holding down the up arrow and pressing power, this will put you into bootloader mode.
Open RSD Lite 4.6
Flash the SPRecovery_ESE81.sbf file with RSD Lite.
this should just flash the recovery if not download a rom like SMOKEDGLASS unzip and put in folder on SD named Nandroid
Once the phone is completely rebooted into rooted android, power it off.
alternately u can install BuglessBeast froyo v 02.1 from alldroid.org then skip to these steps below
Hold down “T” on the keypad and power on phone.
Plug into computer and open HW Virtual Serial Port (your drivers should install and connect etc)
In HWVS set the IP address to 192.168.16.2 and the port to 11008, choose the com port 10 click connect. (For this tutorial we will use COM10)
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
On security tab send SPC 000000. (msg says phone accepts blah blah blah
Go to tab labeled “Other” and write prl. For Cricket EVDO, 6499(new service plan) and 38515 is recommended.
Go to NAM and enter MIN ex. 615-555-5593 (usually different from your actual phone# and MDN(your mobile number ex. 615-555-5551 and click write.
Goto “Memory” tab and click write under NV items, find the downloaded NV items you got from here
for example you must generate the NV items by inputing your MDN([email protected]). box opens telling you to save them as .txt and select them with cdma 2.7. (Thanks again to insanecain)
It should then say, 12 NV items were successfully written to phone.
Go to Main tab and click mode reset.
You can now close HWVS and CDMA WS and open cmd.exe on your computer.
if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone
Once phone reboots go to the market using WI-FI and download and install Autostart root required
Open the Voice Dialer on the phone and say “Open APNs” and click open.
Click on the Verizon and edit everything to match below:
Name - Cricket
APN internet
Proxy wap.mycricket.com:8080
Port 8080
Username [email protected]
Password cricket
Server wap.mycricket.com
MMSC http://mms.mycricket.com/servlets/mms
MMS Proxy wap.mycricket.com
MMS Port 8080
MCC 310
MNC 004
Authentication Type PAP or CHAP
APN type <Not set>
Now click the menu button and click Save.
Before starting the next step make sure you have the u2nl file in your this folder c:/android/tools and also that you have you autostart.sh file in this folder c:/
Now go to command prompt and type the following commands,
cd c:\android\tools
adb shell
mkdir /data/opt/
exit
adb remount
adb push c:\android\tools\u2nl /system/bin/u2nl
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
chmod 0755 /system/bin/u2nl
chmod 0755 /data/opt/autostart.sh
adb reboot
Now, once your phone has rebooted, you should have working web, mms, app, gps, and all. If you don’t go back and check all the steps to insure you did everything exactly right.
thanks everyone for reading.
i would also like to thank everyone who helped give back to the droid community by solving this, (I gave up and switched back to my eris for full support like a Beeach! which i bricked twice) im back on DROID baby
currently running BuglessBeast Froyo v 02.1 and the p3 1000 kernel.
quadrant score: 972
this is a very good set up thanks for the post!
Open CDMA WS 2.7 and (go to settings tab and deselect NV Enabled) then connect to COM10. if you dont deselect you will get PHONE FAILED ERRORS
Click to expand...
Click to collapse
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
broken linkkkkkkzzzzzzzzzzzzzzzzzzzz
"the guide" http://rootyourdroid.info/guides/obtaining-root/
Click to expand...
Click to collapse
is a broken link : (
ummm...flashed new rom...now no web,mms
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
i have a motorola droid on metropcs help me please awwwwwww!!!!
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
somebody hit me up with the info
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
fredline12002 said:
is a broken link : (
Click to expand...
Click to collapse
not sure whats up with the link, just google a new how to root, sorry
Geniusdog254 said:
I get the phone failed error, but I don't see the NV Enabled option. Nor do I see the settings tab, where is that option?
Click to expand...
Click to collapse
when u open HV serial Port, its the second to last or maybe last tab,,, you cant miss it. this is where u make sure NV Enabled is NOT selected
Wolfdragon said:
ok, so im trying like hell to give this moto a shot. normally an htc fan. but the display, camera, and physical keyboard for the price was enticing. i did everything and got internet for a while. then i decided to load bugless' latest rom, now i have no web or mms. is there someting i have to redo??? knowing the norm with reflashes, i did the "open APNs" and redid everything there....but still no go. do i have to redo the Command prompts and the autostart download fr market?
*edit* did all the changes over...ALL. Still no web. if it helps any i did notice that i was unable to reprogam the phone using *228. it still works rite now (i guess based on the previous OTA), but it wont reprogram...i get "programming unsuccessful". I'M running PRLs 38003 & 6499 in Charlotte N.C. any help would be greatly appreciated.
Click to expand...
Click to collapse
If your on 2.1 bugless you need to redo allthe steps for fully working rom, maybe for 2.2 also i havent had to for a while, only bcuz i have cricket and roam off metro.
luvjones305 said:
yes my phone was flashed on metropcs its a motorola droid 2.1 android (rooted) an i was deleting some files on my sd card today cuz it was too full an my phone rebooted all the way to the begining i had to look for a wifi connection to sign in my google ACCOUNT to use my phone again an i lost my internet connection an mms messaging but my phone still can text an make calls but my internet an mms i gone please help me to get it back on thanks
Click to expand...
Click to collapse
you need to be more specific with wat u deleted?? which rom u ran? etc where did u get it flashed? most likey u went to a metro dealer, to get it flashed, METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around.
luvjones305 said:
i need help with my phone i ned to put my mms on an internet back on i lost it when the phone reebooted but its still can text an call on metropcs android motorola droid 2.1 rooted
Click to expand...
Click to collapse
what market are you in? who flashed your phone? quoted from above "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "
Metro Fix Web/mms
"[/QUOTE] "METRO sent out a update a 3 weeks ago (7/06/2010) that DISABLED ALL Dealer added ESN's from Hoodini. so u may just be out of luck. i will search to see if thats been fixed or worked around. "[/QUOTE]
For anyone having trouble with MMs/web on METRO please check out this thread. read from pg one if you dont know whats going on. or pick up here if you can perform the web/mms work around.
http://www.howardforums.com/showthread.php/1656326-Phones-and-more-info/page11
Grr
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
................... bump
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
iNFiNiTY125 said:
This is a great! Thank you for the instructions!
I am having one problum tho, and its very annyoing!!
When i first turn on my fone everything works internet+MMS+GPS+TXT+CALLS everything!
then when i recive or send a text or call (Anything that has to use 1X i think) I loose Internet+MMS and GPS
the only way it comes back is if i restart my fone!
dose anyone have any ideas? did i do somthing wrong? Please help.
I have a idea i know its possible on some phones to switch it so texts use 3G insted of 1x. Could i switch that on my droid?
Oh and im running bugless beast 2.2
Click to expand...
Click to collapse
from my understanding, cdma networks calls and text dont go through data connections, so when u place a call it will switch only to bars and no 1x/3g.
MMS and web will only work when not connected to a call ( i think thats what your stating??) ive never had a problem with data connection not coming back to phone after a call.... hopefully i answered your questions? and gps shouldnt be bothered at all that may be a rom issue. try a few roms other that bugless beast thats basically a stock ROM look into lithium mod or Chevyno1
tko1 said:
good tutorial im just stuck at the step its written a little unclear im a moto newb unfortunately
""if you have QPST open it on the com port 10 read your settings. under MIP mip2,,PPP(Um,AN...etc it should say [email protected] etc in the right columns....in the bottom box password may need to be written to phone, just type in cricket for both Um and An, cricket is the password.
Also select mobile ip+simple ip under MiP tab
select write to phone""
i have downloaded cdma 2.7, nothing was stated about qpst in the necessary tools but i downloaded that too afterwards, and its not clear where i should go at this point after the initial reboot. are these directions for cdma2.7 or qpst? help???
Click to expand...
Click to collapse
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
dortega2388 said:
Hello sorry in advanced for the newbie question. My Moto Droid is already flashed to cricket. If I wanted to manually install 2.2 would I have to start with all steps or just from the 2.2 install?
Click to expand...
Click to collapse
you should be fine with the NV items. after you flash 2.2 dial 611 (you may need to reflash PRL, and then from there i would give your phone about a 2minutes to see if any 1x/3g show up. if not commence with the instructions lol.
bigslanki said:
hello, lets see i believe this was originally the instructions to get the data working. so you needed QPST to enter in the passcode "cricket"....it just depends what rom you have. if you flash a rom and your data doesnt work then u will have to enter those settings in qpst. after entering those your data should work.
Click to expand...
Click to collapse
thanks for the reply, well i had all but given up on my droid dreams and i figured out on my own that they were QPST directions but were missing this important piece. QPST 2.7 WITH A OLDER BUILD LIKE 264 WILL NOT CONFIGURE THE DROID,IT GIVES AND ONLINE ERROR. YOU SHOULD USE AN UPDATED VERSION. I ENDED UP FINDING 2.7 BUILD 323.
Also. its unclear as to why in the adb commands we have
adb push c:\android\tools\autostart.sh /data/opt/autostart.sh
Now:
adb shell
it may be obvious to some but if Now: is an actual command it wouldnt work. so im assuming it isnt, and pretty much adb after that point is irreconcilable.
no matter what the droid never left the verizon network needless to say, and i havent recieved any input as to where i could have gone wrong, everything else was flawless up until the Now: part basically then i had to piece together adb. even tried without the now part and didnt succeed.
i did this and everything works. only problems is it 1x all the time; how to i get 3g?
Hello,
this is my first time i installed a custom rom.
I downloaded the slim rom from official slim rom website (Slim-i9100-4.4.2.build.5-OFFICIAL-4068).
All work well except the mobile network, I can access 3G and wifi but not to make calls or send sms.
I installed GetRil to verify compatibility between my baseband and my RIL (see attachment).
I downloaded and Ril BVL2 modem and installed from the recovery mode, but no thing work
Please I need your help
ksad said:
Hello,
this is my first time i installed a custom rom.
I downloaded the slim rom from official slim rom website (Slim-i9100-4.4.2.build.5-OFFICIAL-4068).
All work well except the mobile network, I can access 3G and wifi but not to make calls or send sms.
I installed GetRil to verify compatibility between my baseband and my RIL (see attachment).
I downloaded and Ril BVL2 modem and installed from the recovery mode, but no thing work
Please I need your help
Click to expand...
Click to collapse
have you checked your APN settings? you may need to change some things depending on your carrier.
Same problem after APN setting changed
efan3719 said:
have you checked your APN settings? you may need to change some things depending on your carrier.
Click to expand...
Click to collapse
Thanks for your answer efan, yes i had checked APN setting.
I copied the setting from my galaxy S4 but the network still unavailable.
Any other ideas ?
ksad said:
Thanks for your answer efan, yes i had checked APN setting.
I copied the setting from my galaxy S4 but the network still unavailable.
Any other ideas ?
Click to expand...
Click to collapse
Goto you settings and check your imei number and check it against the tag on the case under the battery if its what I think it is I had the same when I had a i9100 basicly your efs folder has courpted some how by rights you should of done a back up do a bit of googling its very common and could be easy to restore if I'm correct your device will show a generic imei like this 004999010640000
If yes there are apps on play store that could help restore your efs folder
DO NOT POST YOUR ORIGNAL IMEI ON HERE
if you get stuck pm me and I'll help best I can
There is an amazing guide on here somewhere do a search for it but it shows the steps to take to restore your data settings. u need your msl number there is an app on the market just type msl (must be rooted) and the dial code is ##3282# it will ask for view or edit mode and then the msl code there u can restore your data settings
Sent from my HTC One SV using XDA Free mobile app
INTRO:
The mission of this thread is to make some potentially important information available to all users that have the SCH-S968C(All Tracfone carrier models) that has been gathered over the last year and a half for flashing CM/CM based ROMs on the SCH-S968C .
Though this information is available in many other places, I'm collecting it all into one place to try and make it as painless as possible for everyone with the SCH-S968C. This guide is a long one and has many steps but I've attempted to make it as straightforward as possible for those that are new to rooting and flashing.
BACKSTORY:
Starting from some time in 2014 there have been a lot of users with the SCH-S968C that have flashed a CM11/CM12/CM13 or CM11/CM12/CM13 based custom ROM and didn't have mobile data(3G) or even no cellular signal after flashing and were like:
"OH MY GOD! WHAT DID I DO!?"
Then they would start flashing other ROMs or flashing back to stock to straighten the issue out, only to find that didn't help and none of the typical or expected solutions would correct the issue. Many were flashing modems and swapping system files in an effort to get data working, all of which ended with either a non-working device or a bricked device, do not try the things they tried, that is not the fix for the situation.(if you are one of the ones that lost signal and can't get it back even on stock, I'll discuss the fix for that in TROUBLESHOOTING at the end of this guide).
THE REASON:
These users would have no signal after flashing because unfortunately, these ROMs are built for the Verizon S3 SCH-I535 but the SCH-S968C can flash them(it actually has the SCH-I535 Verizon motherboard with 4G disabled in the hardware, making it 3G only). The Verizon S3 is a 4G/LTE device, Verizon uses a CDMA 4G/LTE SIM in their 4G devices to regulate 4G data. This SIM requirement is built into the ROMs themselves. Even though the SCH-S968C is a 3G device, this makes these ROMs require a CDMA 3G/4G/LTE SIM when flashed on the SCH-S958C to receive at least data(some of the ROMs even require it for cellular service also, not just data).
The discussion of all of this about the SIM, what has been tried to bypass the SIM and the things discovered to leave the SIM and get everything working at its best can be found in THIS THREAD. Most of the issues and fixes for the KK and newer ROMs, all the troubleshooting and fixes associated to getting working data/MMS/SIM correctly configured along with restoring if you have issues can be found in the linked thread, mostly toward the end and not so much the middle.
***PREREQUISITES***
]1[-Rooted Galaxy S3(SCH-S968C) obviously, lol.
]2[-(Optional)If you're going to use PC to do your downloading and moving files then you'll need the "USB drivers for Samsung phones"(install on PC), download: HERE
]3[-ES File Explorer installed, download: HERE
]4[-Terminal Emulator installed, download: HERE
]5[-TWRP Manager or Flashify installed.
]*[ Download TWRP Manager: HERE
]*[Download Flashify: HERE
]*[(Optional)For those that manually download the .img with a mobile browser, it will be in your download folder, those with PC download it then transfer it to the device where you can find it, flash it with Flashify. Download TWRP .img: HERE.
]6[-CDMA 3G/4G/LTE SIM(absolutely MUST have a SIM or you won't get mobile data/MMS to work), below is a list of SIMs that should work and the results of using them, you'll need a micro SIM or a full-size SIM trimmed to fit micro(a nano SIM with adapter to fit micro will work as long as it is a CDMA, not a GSM SIM).
]*[Previously activated Verizon 4G LTE SIM.($3-5 on eBay)
(results are APN settings are accessible and mobile data/MMS works correctly)
]*[New, never activated Verizon SIM
(most users with a new SIM have working mobile data(3G) but have had issues accessing APN settings to get MMS working, some have had no issue accessing APN settings, some users with a new SIM also had a random dialing issue that would dial a *2289X number, the cause was never identified, this issue doesn't happen with a previously activated Verizon 4G/LTE SIM).
]*[Straight Talk BYOP CDMA 4G/LTE SIM(not the AT&T/T-Mobile SIM, those are GSM and won't work)(I haven't been able to verify if there is a difference between used and new ST SIMs but mobile data should work and if APN settings are accessible you should be able to get MMS working, hopefully users will post their results here with new and used ST SIM).
]7[ (Optional)-Titanium Backup installed, download: HERE
***PREPARING BEFORE FLASHING***
***NOTE***For the users that don't have a PC to do their downloading and file moving, I'll provide instructions for using ES File Explorer to do everything.***NOTE***
***NOTE***You can use your PC instead of ES File Explorer for everything EXCEPT copying /efs, this step will be done using the device to keep it simple for those that don't have PC and because PC method to pull a copy of /efs is a bit technical for the average user, I will only be explaining for using ES File Explorer.***NOTE***
]1[-For steps later in this guide(and for general purposes), you'll need to enable Root Explorer and mount R/W in ES File Explorer. To do this open ES File Explorer and tap the menu button.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
]2[-Tap the "Tools" tab.
]3[-Scroll down the menu and tap the words "Root Explorer"(not the toggle switch), it will turn on when you tap the words(grant superuser/root permission if prompted).
]4[-Tap "Mount R/W".
]5[-Your list of partitions may be different than mine but generally you want all partitions EXCEPT firmware-mdm set to RW as shown in screenshot. Tap OK when done.
]6[-It is recommended to make a NVdata backup to protect IMEI then save a copy of your /efs folder before flashing custom ROMs. IMEI is very easy to lose depending on what you flash and the order you flash it in with this device.
]*[(RECOMMENDED)Comprehensive guide to backing up IMEI/efs HERE
]*[For those that don't have a PC, open the Terminal Emulator app and type:
su(press enter, grant superuser/root permission if prompted)
Then type:
reboot nvbackup(press enter, the device will reboot).
]*[This saves NVdata/IMEI to be restored later if flashing wipes IMEI, instructions for restoring posted below in TROUBLESHOOTING).
]7[- It is also recommended to save a copy of your /efs folder on your extsdcard, we will use ES File Explorer. Open ES File Explorer and take note of what your extsdcard is labeled as and remember it, you'll need to know this later, then swipe from right to left to go a page over.
]8[-Tap the / symbol.
]9[-Press and hold the /efs folder to highlight it then tap the "More" button at the bottom.
]10[-Tap "Copy to"
]11[-Tap the arrow at the top left(what it says will be different depending on the ROM you're using).
]12[-Remember the name of your extsdcard? Select your extsdcard.
]13[-When you get to your extsdcard, tap "OK"(Those with PC can now connect to PC and save a copy of /efs on PC, you may have to enable MTP in the USB options that pop up when you connect device to PC to grant the PC access to device storage).
]14[-Open Titanium Backup(grant superuser/root permission if prompted while using Titanium Backup), backup all apps/data/settings you want to keep(Follow the guide I linked to determine what you want and what is safe to restore after flashing a new ROM, some things won't restore in a new ROM without causing issues), instructions for using Titanium Backup HERE.
]15[-To simplify moving files and to keep everyone on the same page when finding your files when you flash them we will create a folder on extsdcard and name it ABC(or whatever you want as long as you know which one it is), this will make it easy to find in TWRP when you flash your ROM.
Open ES File Explorer and select your extsdcard.(Those with PC can use PC to do this)
]16[-Tap the "New" button.
]17[-Tap "Folder".
]18[-Name the folder "ABC"(or whatever you choose) then tap OK.
]19[-Download the KK/LP/MM d2lte or d2vzw ROM(s) of your choice and store it/them in the folder you created on your extsdcard. You will find ROMs, custom recoveries, custom kernels and various other mods that can be used on the SCH-S968C in the links below.
]*[ROMs+other mods: HERE
]*[More ROMs: HERE
***EXTREME CAUTION***(DO NOT use anything that says STOCK/STOCK based or TW(TouchWiz) in its name, nothing that says firmware or modem, nothing that mentions Safestrap Recovery or Flashfire, locked Bootloader(BL). All of these things are specifically for the Verizon SCH-I535 and will almost certainly lead to hard bricking your device if you attempt to use them.***EXTREME CAUTION***
]20[-Download the appropriate Gapps for the ROM(s) you chose and store it/them in the folder you created(the version of Gapps you need should be mentioned wherever you get your ROM from).
]21[-Charge battery to full.
]22[-Now you're safely prepared to start the flashing process, proceed to the next steps.
***FLASHING TWRP***
It is recommended to always use the newest version of TWRP available for best results. If you already have the newest version then skip to FLASHING YOUR ROM, if you don't have it then follow instructions below.
To make this easy for those that are new or don't have a PC, we will use TWRP Manager or Flashify to flash TWRP, or by manually downloading the TWRP .img(linked above) then flashing it in Flashify.
***FLASHING WITH TWRP MANAGER***
]1[-Open TWRP Manager(grant superuser/root permission at any time while using TWRP Manager). Tap "Device Name".
]2[-Scroll down the list and select "Samsung Galaxy S3 Verizon d2vzw".
]3[-Tap "Recovery Version to install".
]4[-Select the newest version available.
]5[-Tap "Install Recovery".
]6[-The .img will download.
]7[-When the .img downloads it will prompt you to verify the partition to flash to, verify you have the same thing and tap "yes".
]8[-When the .img finishes flashing, you will be prompted to reboot to recovery, tap "yes".
***NOTE***Skip to BACKING UP YOUR STOCK ROM if you used this method to flash TWRP.***NOTE***
***NOTE***If you've tried this and you're having issues with this method, refer to the method below***NOTE***
***FLASHING WITH FLASHIFY***
]1[-Open Flashify and tap "Recovery Image"(grant superuser/root permission if promoted while using Flashify).
]2[-If you manually downloaded the .img(linked above as an option in PREREQUISITES), tap "Choose file", then select it from your download folder or wherever you stored it then skip over the next two steps below this one for downloading the .img in Flashify.
If you haven't manually downloaded the .img, skip this step and go to the next step to download the .img in Flashify.
]3[-Tap "Download TWRP".
]4[-Select the newest version available.
]5[-The .img will download(it will be downloaded in /flashify/recoveries/twrp/ folder if you ever need to find it.
]6[-When it downloads or when you select the .img from storage, it will prompt you to flash the recovery.img, tap "yup".
]7[-After it flashes, tap "Reboot now".
]8[ Proceed to BACKING UP YOUR STOCK ROM.
***BACKING UP YOUR STOCK ROM***
]1[-When you are booted to TWRP, if you are still on stock and you haven't made a NANDroid backup, make it now by selecting the "backup" option before you flash anything!(Very important step)
]2[-Tap "Select Storage".
]3[-Select your extsdcard(Micro SDCard), select OK.
]4[-The default partitions selected to backup are fine, swipe the slider to confirm, this NANDroid backup can be used at any point in the future to restore the device to stock if you have issue or ever want/need to.
]5[-Press the Home button in TWRP to return to the Main screen and proceed to FLASHING YOUR ROM.
***FLASHING YOUR ROM***
]1[-While still in recovery after making your stock NANDroid, remove battery cover and insert SIM then replace cover.
]2[-Tap "Wipe".
]3[-You'll see "Wipe Data, Cache and Dalvik(not including internal storage)" at the top, swipe the slider to perform the wipe and wait for it to finish.
]4[-Tap the Home button in TWRP to return to main screen, select "Install".
]5[-Select "Up a level".
]6[-Select "external_sd".
]7[-Select the "ABC" folder you created(or whatever name you chose for the folder, scroll down the list if needed).
]8[-Select your ROM.zip.
]9[-Tap "Add more zips".
]10[-Select your Gapps.zip.
]11[-Swipe the slider to confirm the flash.
]12[-After flashing, tap "Wipe cache/dalvik".
]13[-Swipe the slider to confirm.
]14[-Tap "Reboot System".
]15[-Wait for the phone to boot(It will take 10-20 minutes to fully load), when it boots into Setup Wizard, stop and watch the status bar Network Signal icon, wait for the device to detect the SIM, when the icons shows a signal(and 3G if you're lucky, if you are not getting any 3G then just get on WiFi to finish setup if you have WiFi or if you don't have WiFi, skip setup and go on to SETTING UP DEVICE AND SIM, you can sign in to Google to finish setup after you get the SIM and APNs set up), then go through Setup Wizard to set up the device and sign in to your Google account. When you're in the phone, continue to setup steps below.
***SETTING UP DEVICE AND SIM***
***NOTE***Your system settings may look different depending on your ROM but the settings should be the same or similar, find the settings described wherever they are in your ROM and set them to what is posted.***NOTE***
]1[-Go to System Settings>About>Build Number.
]2[-Tap build number at least 7 times quickly to enable Developer Options(you'll get a toast message saying you have enabled development options).
]3[-Go to System Settings>Developer Options.
]4[-Set Root Access to "apps and adb".
]5[-While still in developer options, verify USB debugging is on(neither is needed for setup but turning them on now prevents potentially confusing issues later).
]6[-Open your dialer app and dial:
*228(if your SIM is a Verizon SIM), press send, this programs the SIM, hangup when done.
OR
*2289X(if your SIM is a Straight Talk SIM(or any other Tracfone variant CDMA SIM). I can't confirm the actual number, I haven't used this SIM), if your SIM is a ST BYOP CDMA 4G/LTE SIM then this number should program the SIM, I can't confirm that though, if it doesn't we'll have to hope someone that used ST 4G posts what they had to do, hang up when done.
]7[-Go to System Settings>Mobile Networks(tap the words, not the toggle switch.
]8[-Set Preferred Network to "3G".
]9[-Set CDMA Subscription to "NV".
]10[-Select Access Point Names.
]11[-Then select one of the existing APN sets on the list(any set, it doesn't matter, do not create a new set, you have to edit an existing set or they won't save, your list won't look the same as mine).
]12[-Edit the APNs using either set I have posted, the Tracfone set should work on all Tracfone network variants. Change only the values listed.
]*[Tracfone APNs, enter the name of your Tracfone network Carrier variant in the Name value(These APNs are for all Tracfone devices including BYOP devices).
Name: (Your network variant)
APN: tfdata
Port: 80
MMSC: http://mms-tf.net
MMS Proxy: mms3.Tracfone.com
MMS Port: 80
]*[Verizon APNs(these will also work on the Tracfone variants since they are on Verizon towers).
Name: verizon
APN: internet
MMSC: http://MMS.vtext.com/servlets/mms
MMS port: 80
MCC: 310
MNC: 012
APN Type: internet,mms
]13[-When you've entered the APNs, tap the menu button.
]14[-Save the edited APNs, the set you create might disappear but they are still there and will still work as normal.
***NOTE***If you flashed a 4.4+ ROM first and now you want to go up to 5.0+/6.0+ and you have working data, now would be a good time to reboot to TWRP to flash the 5.0+/6.0+ ROM and Gapps like instructed in the above steps. When you get them flashed, do these same steps to make sure everything is set where it needs as you go back through everything.(or dirty flash with no factory reset, only wipe cache and dalvik after flashing and ONLY as long as it is an update to the same ROM you are using, for example, CM11 to CM12 or AICP 5.0 to AICP 6.0, hopefully dirty flashing will let you keep APNs configured in some of the newer ROMs that don't give access to APN settings instead of having no way to change APNs in your new ROM, also, some of the ROMs don't have the settings built in the ROM because they have World APNs so shouldn't need the settings configured)***NOTE***
]15[-Reboot the device to reload settings.
]16[-After the device reboots you should have working mobile data and MMS(You can sign in to your Google account now if you had to skip it in setup), install Titanium backup using the copy of the app you placed on extsdcard then open Titanium Backup and restore all the data you backed up in Titanium Backup, reboot after restoring data from Titanium Backup.(You will need to go to System Settings>Security>Unknown Sources and turn it on to install Titanium Backup if you're installing from a copy you manually saved, or you can install it again from the Google Playstore)
]17[-Remember to set Root Explorer and mount R/W in ES File Explorer as described in PREPARING BEFORE FLASHING section posted above before proceeding to the next step.
]18[-Once everything is set up the way you want, mobile data/MMS are correctly configured and all data is restored from Titanium Backup, you can boot to TWRP and make a new NANDroid backup of your custom ROM with everything working, this can also be used to restore later if you have issues. Remember, at this point you should have a stock NANDroid backup and a custom NANDroid backup if you've followed the instructions, either can be used when/if you need it. Reboot after making the new NANDroid backup.
]19[-Enjoy!!!
Ink'd from my KrAkEn'd S3
***Troubleshooting***
]1[-ISSUE-You've tried flashing a CM12/CM13 or CM based Lollipop/Marshmallow ROM but you are getting a bootloop.
]A[-POSSIBLE FIX- Did you wipe data/wipe cache/wipe dalvik cache before/after flashing then rebooting?
]B[-POSSIBLE FIX- When coming from stock to Lollipop or newer it is sometimes necessary to do a clean install when flashing the ROM, to clean install, Boot to TWRP, select "Wipe".
]*[Then select "Advanced Wipe".
]*[Then select "System" and "Data" partitions(do not select any other partitions). Swipe the slider to confirm the wipe.
]*[Tap the home button and continue by flashing ROM and Gapps normally as posted in FLASHING YOUR ROM above.
]2[-ISSUE- You flashed a ROM and lost Signal.
]A[-POSSIBLE FIX- Check Network Settings to verify you're set to 3G and NV, if you flashed a custom ROM before this and had working data then flash back to that ROM and check network settings in that ROM also.
]B[-POSSIBLE FIX- Check System Settings>About>Status>IMEI and verify you still have IMEI. If you have lost IMEI then follow steps below.
]*[(Recommended)-Refer to the Comprehensive guide to backup IMEI/efs to restore IMEI HERE
]*[-Open Terminal Emulator and type:
su (press enter, grant superuser/root permission if prompted)
Then type:
reboot nvrestore (press enter, this will restore your IMEI)
]*[-Restoring the nvbackup using Terminal Emulator erases the backup from where it was saved so you'll need to make another NVdata backup using the same method described above in the PREPARING BEFORE FLASHING section.
]*[-Copy your efs folder back to its location on your device(overwrite the existing file if needed), reboot device.
]3[-ISSUE- You flashed a 6.0 CM/CM based ROM and now your PC sees your device but isn't seeing your device storage.
]A[-Possible fix- When device connects you'll see a notification in status bar, pull down notifications and open options, select MTP.
***NOTE***THIS THREAD(linked above also) discusses various issues when flashing these ROMs and using SIM, remember to patiently read through it if you have issues and you'll probably find your answer, the issues and fixes are spread through many months of posts so it's not going to be a fast find, but with diligence to suffer through the agony of reading posts you'll most likely find your answer***NOTE***
Hello. Nice guide here. Only problem I have is APN settings not accessible with cm 12.1 and a new ST SIM card. Tried to visit link for different ROMs and everything on fixin SIM/MMS, but links are broken.
Polston92 said:
Hello. Nice guide here. Only problem I have is APN settings not accessible with cm 12.1 and a new ST SIM card. Tried to visit link for different ROMs and everything on fixin SIM/MMS, but links are broken.
Click to expand...
Click to collapse
The links work fine for me, try a different browser or something.
As stated in my guide, new, never activated SIMs usually can't access APNs but previously activated ones can, get a used Verizon SIM from eBay for $3-5, they have APNs stored on the SIM, this allows you to edit them.
Or you can try different ROMs to see if APNs are accessible, some can and some can't because some of the ROMs have world APNs built in(these don't have APN settings), the ones without world APNs should be able to access APN settings.
Sent from my SCH-I535 using Tapatalk
I ended up doing a clean install of octos 6.0 ROM and works like a charm. No Verizon SIM needed. Flawless for me so far. Regardless , your posts taught me a lot on multiple sites. Amazing the s3 can run android 6.0. Cheers
Polston92 said:
I ended up doing a clean install of octos 6.0 ROM and works like a charm. No Verizon SIM needed. Flawless for me so far. Regardless , your posts taught me a lot on multiple sites. Amazing the s3 can run android 6.0. Cheers
Click to expand...
Click to collapse
You're using no SIM and you have data working?
Oh wait, you got it working with the ST SIM, cool.
Sent from my SCH-I535 using Tapatalk
works with a but
got an un-used Verizon 4g lte sim and got data after calling *228 but after a restart it will go back to apn setting not available for this user but still has data but not mms, untill dialing *228
this is with cm12
this must be the problem with new verizon lte sims
stoneman1924 said:
got an un-used Verizon 4g lte sim and got data after calling *228 but after a restart it will go back to apn setting not available for this user but still has data but not mms, untill dialing *228
this is with cm12
Click to expand...
Click to collapse
Are the APNs saving when you can access them? If so then a reboot shouldn't reset everything. You have to edit an existing set or they won't save, creating a new set won't save, only editing existing sets works.
Sent from my SCH-I535 using Tapatalk
Droidriven said:
Are the APNs saving when you can access them? If so then a reboot shouldn't reset everything. You have to edit an existing set or they won't save, creating a new set won't save, only editing existing sets works.
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
that helps to know that i will try that now
---------- Post added at 03:03 AM ---------- Previous post was at 02:51 AM ----------
im doing a factory reset then dialing *228, modifying one of them.(can i delete the rest?).im hoping not having to buying another sim but i have hadthe mms and data work with this card but after 30 min it seemed to start giving me trouble
stoneman1924 said:
that helps to know that i will try that now
---------- Post added at 03:03 AM ---------- Previous post was at 02:51 AM ----------
im doing a factory reset then dialing *228, modifying one of them.(can i delete the rest?).im hoping not having to buying another sim but i have hadthe mms and data work with this card but after 30 min it seemed to start giving me trouble
Click to expand...
Click to collapse
Leaving the rest of them won't harm anything, you can delete them if you want but once they are gone there's no getting them back.
In my experience, I've seen better results with a used SIM from Verizon, they are easy to get and cheap for $3 to $5 on eBay.
Sent from my SCH-I535 using Tapatalk
Polston92 said:
I ended up doing a clean install of octos 6.0 ROM and works like a charm. No Verizon SIM needed. Flawless for me so far. Regardless , your posts taught me a lot on multiple sites. Amazing the s3 can run android 6.0. Cheers
Click to expand...
Click to collapse
Do you have working MMS?
Sent from my SCH-I535 using Tapatalk
so my phone still clears apn settings after a restart untill i call *288. ps i needed to reflash the zip and click on cm13 by accident but it seems to download and apn from *228 and work without modification
stoneman1924 said:
so my phone still clears apn settings after a restart untill i call *288. ps i needed to reflash the zip and click on cm13 by accident but it seems to download and apn from *228 and work without modification
Click to expand...
Click to collapse
I didn't quite understand that, can you clarify what you're saying?
Are you saying the APNs are disappearing?
Typically on this device, when you edit and save they disappear but still work, that's normal for this device if that is what you mean.
Sent from my SCH-I535 using Tapatalk
After dialing *228 im given the apn list. One of them works from the start with no modifications and is named straight talk. But after rebooting the phone the list will be blank and say apn setting not available for this user(data works but no mms). If i dial it again the list returns and the phones mms works onces again. Im guessing this is the errors you have been talking about but i got the sim card befor your guild.
I will most likely buy another card used but im not much of an ebay user
And im sorry my English is vary bad
Sent from my SCH-I535 using Tapatalk
---------- Post added at 05:04 AM ---------- Previous post was at 04:55 AM ----------
The apn it defaults to and works on is basically blank but it works. As long as i dont restart the phone. I have not tested to see what happens over a long period of time, my guess is it will eventually stop working again. But i will keep my phone on over night and see if i can mms in the morning
Sent from my SCH-I535 using Tapatalk
stoneman1924 said:
After dialing *228 im given the apn list. One of them works from the start with no modifications and is named straight talk. But after rebooting the phone the list will be blank and say apn setting not available for this user(data works but no mms). If i dial it again the list returns and the phones mms works onces again. Im guessing this is the errors you have been talking about but i got the sim card befor your guild.
I will most likely buy another card used but im not much of an ebay user
And im sorry my English is vary bad
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
Wait before you get the SIM. I might can work something out for you. You're the first person to mention getting APN settings back after they weren't available and the first to mention that you lose them after a reboot. Does your data and MMS still work after rebooting?
I'm going to contact some developer associates of mine and see if we can't use this information to come up with a working fix for it, if so, you won't need another SIM but if you'd rather not wait then go ahead get the SIM.
You have me curious to see if there is something useful that can be done like writing a script or something to run at startup to keep your issue from happening. Whether its a script or not there may still be a chance there could be a small breakthrough for this device when using these ROMs.
Sent from my SCH-I535 using Tapatalk
I am more than happy to wait I'm more interested in the process of getting this to work then I am updating my phone after a reboot and APN settings disappear I lose the ability to MMS but I still am able to use data.
If there is any information I can send you please let me know I am more than happy to send it
I am doing this with the CM 13 nightly build but I'm not up to date this current moment because that would require a reboot
Sent from my SCH-I535 using Tapatalk
stoneman1924 said:
I am more than happy to wait I'm more interested in the process of getting this to work then I am updating my phone after a reboot any APN settings disappear I lose the ability to MMS but I still am able to use data
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
In the meantime, if you want to use MMS you can use Hangouts or a third party texting app from the Playstore, there are several different ones, third party texting works fine, its the stock messenger in these ROMs that doesn't work without the APNs, third party doesn't need it.
Sent from my SCH-I535 using Tapatalk
Doesn't hangout require the other person to have it as well or will they receive it as a normal text
If you need any info from me let me know I am more than happy to give it to you
Sent from my SCH-I535 using Tapatalk
stoneman1924 said:
Doesn't hangout require the other person to have it as well or will they receive it as a normal text
If you need any info from me let me know I am more than happy to give it to you
Sent from my SCH-I535 using Tapatalk
Click to expand...
Click to collapse
Yes, but some of the third party apps don't require the other person to have it.
BTW, if you use the reply button under someones post(if you're using a browser) it will quote whoever you're replying to and they'll get a notification to let them know you replied.
Or if you're using an app to view this form, tap the persons post then tap reply and it will quote them.
This way they know you replied instead of having to purposely come look to see if you replied.
You can also give someone a mention if you want to get their attention by putting @ on the beginning of their name like this @stoneman1924, this also gives them a notification that you mentioned them so they'll know to come look. It makes it easier for everyone if you use the quote system and the mention system. I've quoted your post every time I replied, it gave you notifications that I had replied to you so you could check my reply didn't it?
Sent from my SCH-I535 using Tapatalk
dose anyone have the latest cm13 nightly zip, i didnt notice the cm14 and updated and cant get it back to cm13
Hello,
I've rooted a few phones, but I don't really do too much with them, I mostly root them to have an easier time transferring all data from one phone to the next, and for being able to use a couple of root apps. Basically, I'm not all that good at this stuff, but I can get by most of the time with enough research and time. I have not been able to find a thread that's been able to help me with this problem, though.
My V20's reception practically fell off the map after rooting it. I've been researching and trying to find a way to flash the modem files that I dumped with LGUP before I rooted it via dirtysanta, but I'm not having any luck. The files don't have an extension, but from what I can gather, they should be image files. I'm not 100% on that because I can't seem to find what file type they actually are, my computer only lists them with the description of "file". I run Windows 7 if that matters.
Anyway, based on what I've found so far, the files I need to flash in order to fix my reception problem are:
modem_COM5
modemst1_COM5
modemst2_COM5
fsg_COM5
I can't get fastboot to work, I'm not sure how to link my phone to a file path on my computer from command terminal so that's not been working for me. I've also tried renaming the files by adding ".img" to the end, zipping them and installing them with twrp afterward, but they won't install, giving me an error of "META-INF/com/google/android/update-binary"
Ultimately, I'm lost. Any help is greatly appreciated, as I've spent hours pouring over threads and trying to fix my stupid reception problems. I have no reception at home, none at work, and I have spotty reception while driving or out in other places, but it's generally terrible. I used to have low reception at home, but I could always make a call if I needed to, and I'd have great reception driving around. Then I rooted my phone and my reception tanked.
platypus25_5 said:
Hello,
I've rooted a few phones, but I don't really do too much with them, I mostly root them to have an easier time transferring all data from one phone to the next, and for being able to use a couple of root apps. Basically, I'm not all that good at this stuff, but I can get by most of the time with enough research and time. I have not been able to find a thread that's been able to help me with this problem, though.
My V20's reception practically fell off the map after rooting it. I've been researching and trying to find a way to flash the modem files that I dumped with LGUP before I rooted it via dirtysanta, but I'm not having any luck. The files don't have an extension, but from what I can gather, they should be image files. I'm not 100% on that because I can't seem to find what file type they actually are, my computer only lists them with the description of "file". I run Windows 7 if that matters.
Anyway, based on what I've found so far, the files I need to flash in order to fix my reception problem are:
modem_COM5
modemst1_COM5
modemst2_COM5
fsg_COM5
I can't get fastboot to work, I'm not sure how to link my phone to a file path on my computer from command terminal so that's not been working for me. I've also tried renaming the files by adding ".img" to the end, zipping them and installing them with twrp afterward, but they won't install, giving me an error of "META-INF/com/google/android/update-binary"
Ultimately, I'm lost. Any help is greatly appreciated, as I've spent hours pouring over threads and trying to fix my stupid reception problems. I have no reception at home, none at work, and I have spotty reception while driving or out in other places, but it's generally terrible. I used to have low reception at home, but I could always make a call if I needed to, and I'd have great reception driving around. Then I rooted my phone and my reception tanked.
Click to expand...
Click to collapse
I can make you a zip to flash the files in TWRP
Sent from my ONEPLUS A6010 using Tapatalk
clsA said:
I can make you a zip to flash the files in TWRP
Sent from my ONEPLUS A6010 using Tapatalk
Click to expand...
Click to collapse
Thanks! Do I just need to email you the modem files?
platypus25_5 said:
Thanks! Do I just need to email you the modem files?
Click to expand...
Click to collapse
no you can put them in the zip below
Here's your zip > https://drive.google.com/open?id=1RiNnyS-iF34a543zQAchi70-YAUvc3hn
rename your files to
modem
modemst1
modemst2
fsg
and add them to the zip and save it
copy to phone and flash it
clsA said:
no you can put them in the zip below
Here's your zip
rename your files to
modem
modemst1
modemst2
fsg
and add them to the zip and save it
copy to phone and flash it
Click to expand...
Click to collapse
I appreciate you making the zip, but after flashing the files my phone won't boot up. When I power it on it says that my device has failed a routine safety check and will not boot. I'm accustomed to my phone saying that when I boot it up, as it's done that ever since rooting it, but then it shows the LG logo and then shuts off and will not turn on again unless I take the battery out and reinsert it. I have to go through that process at least 2 or 3 times to get the phone to load up. When I got it to load up again, the top bar of my phone said I had no service, which it did not before flashing the files. I've gone back into twrp and tried re-flashing it again to no avail.
If it makes a difference there were two sets of files when I went to flash, even though I only put in one set. I renamed them according to your instructions, and there were one set that just had the file name and .img at the end (like fsg.img) and another set that started with ._ and ends with .img (like ._fsg.img)
Thanks again for taking the time, I really appreciate the help.
platypus25_5 said:
I appreciate you making the zip, but after flashing the files my phone won't boot up. When I power it on it says that my device has failed a routine safety check and will not boot. I'm accustomed to my phone saying that when I boot it up, as it's done that ever since rooting it, but then it shows the LG logo and then shuts off and will not turn on again unless I take the battery out and reinsert it. I have to go through that process at least 2 or 3 times to get the phone to load up. When I got it to load up again, the top bar of my phone said I had no service, which it did not before flashing the files. I've gone back into twrp and tried re-flashing it again to no avail.
If it makes a difference there were two sets of files when I went to flash, even though I only put in one set. I renamed them according to your instructions, and there were one set that just had the file name and .img at the end (like fsg.img) and another set that started with ._ and ends with .img (like ._fsg.img)
Thanks again for taking the time, I really appreciate the help.
Click to expand...
Click to collapse
I tested the zip myself it works as expected.
The unlocked bootloader message has nothing to do with your issue.
What sim card are you using?
What are your apn settings?
What was the last Rom you flashed?
Are you on Oreo?
Sent from my ONEPLUS A6010 using Tapatalk
clsA said:
I tested the zip myself it works as expected.
The unlocked bootloader message has nothing to do with your issue.
What sim card are you using?
What are your apn settings?
What was the last Rom you flashed?
Are you on Oreo?
Sent from my ONEPLUS A6010 using Tapatalk
Click to expand...
Click to collapse
It's a nano sim from at&t, and at&t is my carrier. I doubt it's relevant, but I use a prepaid plan.
My app settings are:
Name: ATT Nextgenphone
APN: nxtgenphone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Authentication type: None
APN type: default,mms,supl,hipri,fota
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
I believe the last ROM I flashed was H91510e_VTR_CA_OP_1205.kdz
Using the DirtySanta method of rooting, I think I flashed that so I could actually root the phone and then updated to another version, possibly. I'll include my software info in case that is helpful.
I'm not on oreo, I'm running nougat
Android version: 7.0
Android security patch level: November 1, 2017
Baseband version: MPSS.TH.2.0.1.c3-00011M8996FAAAANAZM-1.69323.1. 69645.2
Kernel version: 3.18.31
Build number: NRD90M
Software version: H91010r
Security software version: MDF v2.0 Release 4
Thanks again for all of your help.
platypus25_5 said:
It's a nano sim from at&t, and at&t is my carrier. I doubt it's relevant, but I use a prepaid plan.
My app settings are:
Name: ATT Nextgenphone
APN: nxtgenphone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Authentication type: None
APN type: default,mms,supl,hipri,fota
APN protocol: IPv4/IPv6
APN roaming protocol: IPv4/IPv6
I believe the last ROM I flashed was H91510e_VTR_CA_OP_1205.kdz
Using the DirtySanta method of rooting, I think I flashed that so I could actually root the phone and then updated to another version, possibly. I'll include my software info in case that is helpful.
I'm not on oreo, I'm running nougat
Android version: 7.0
Android security patch level: November 1, 2017
Baseband version: MPSS.TH.2.0.1.c3-00011M8996FAAAANAZM-1.69323.1. 69645.2
Kernel version: 3.18.31
Build number: NRD90M
Software version: H91010r
Security software version: MDF v2.0 Release 4
Thanks again for all of your help.
Click to expand...
Click to collapse
Maybe theirs a setting in the Hidden menu that will help
using a build.prop editor (thanks @ezzony)
Change ro.build.target_operator from ATT to OPEN to bring back all the missing Modem_Settings and the ones that were also missing in regular Settings>Mobile Networks. Also reverted to stock icons in status bar.
in the dialer type > *#546368#*910#
then go to Field Test>Modem Settings>Network Mode and set to Automatic
reboot
you can also check that Volte and VoWifi are enabled from the hidden menu Modem settings
Also in Settings>Mobile Network>Network Mode be sure it's set to the top one (GSM/WCDMA/LTE auto)
clsA said:
Maybe theirs a setting in the Hidden menu that will help
using a build.prop editor (thanks @ezzony)
Change ro.build.target_operator from ATT to OPEN to bring back all the missing Modem_Settings and the ones that were also missing in regular Settings>Mobile Networks. Also reverted to stock icons in status bar.
in the dialer type > *#546368#*910#
then go to Field Test>Modem Settings>Network Mode and set to Automatic
reboot
you can also check that Volte and VoWifi are enabled from the hidden menu Modem settings
Also in Settings>Mobile Network>Network Mode be sure it's set to the top one (GSM/WCDMA/LTE auto)
Click to expand...
Click to collapse
I downloaded a build.prop editor and changed the build target operator setting, but I'm not sure what you mean by reverting to stock icons in status bar or how to do that. Which settings were missing in Settings>Mobile Networks?
I got into that other menu, but under field test>modem settings I can choose either engineering mode or PDP setting.
Engineering mode says "modemprotocol" in the top corner, with previous, up, down, and next buttons. Under that it says ITEM_2G: 0
[Serving Cell Information]
ARFCN: 0
FL_Timeout_v: 0
RXLEV: 0
C1: 0
C2: 0
Other pages for engineering mode are for Item HSPA:0 [HSDPA Information], Item_NM [general information], Item_3G: 0 [RRC State and Serving Cell information], Item_LTE: 0 [LTE Information]
PDP settings says ModemProtocol at the top and has options for [0] Set LG Fast Dormancy, [1] APN setting, [2' Block DataRecovery.
VoLTE and VoWifi are enabled in the hidden menu, but I can't access Settings>Mobile Network>Network Mode. I can't figure out how to check the GSM and other options. I can go to Settings>Mobile Networks and then I can go to:
Mobile data - just turns it on or off
Mobile data reminder
Review reminder settings
International data roaming
Disable 2G
Access Point Names
Search for AT&T MicroCell - When I search, none are found
I hope I'm not just throwing too much useless information for you to sift through. I'm just not entirely sure of what all is relevant.
platypus25_5 said:
I downloaded a build.prop editor and changed the build target operator setting, but I'm not sure what you mean by reverting to stock icons in status bar or how to do that. Which settings were missing in Settings>Mobile Networks?
I got into that other menu, but under field test>modem settings I can choose either engineering mode or PDP setting.
Engineering mode says "modemprotocol" in the top corner, with previous, up, down, and next buttons. Under that it says ITEM_2G: 0
[Serving Cell Information]
ARFCN: 0
FL_Timeout_v: 0
RXLEV: 0
C1: 0
C2: 0
Other pages for engineering mode are for Item HSPA:0 [HSDPA Information], Item_NM [general information], Item_3G: 0 [RRC State and Serving Cell information], Item_LTE: 0 [LTE Information]
PDP settings says ModemProtocol at the top and has options for [0] Set LG Fast Dormancy, [1] APN setting, [2' Block DataRecovery.
VoLTE and VoWifi are enabled in the hidden menu, but I can't access Settings>Mobile Network>Network Mode. I can't figure out how to check the GSM and other options. I can go to Settings>Mobile Networks and then I can go to:
Mobile data - just turns it on or off
Mobile data reminder
Review reminder settings
International data roaming
Disable 2G
Access Point Names
Search for AT&T MicroCell - When I search, none are found
I hope I'm not just throwing too much useless information for you to sift through. I'm just not entirely sure of what all is relevant.
Click to expand...
Click to collapse
reboot after build.prop edit
then all the options show up
the icons change on their own as a result of the build prop edit
clsA said:
reboot after build.prop edit
then all the options show up
the icons change on their own as a result of the build prop edit
Click to expand...
Click to collapse
Alright, I've done this, I've also made a few different access point names for att to try and see if any of those have better reception. Nothing's working all that great, but hopefully at least one of them works a little better than what I've been used to.
Currently I still have no reception where I'm used to having one or two bars around the house. I'm not sure if there is anything else to do without opening up the phone and replacing any parts. If there is anything else you can think of that I might try, please let me know.
Do you think that changing the screen would make any difference on reception? I did have to have mine changed shortly after rooting the phone, but I can't really imagine that could be the cause since I still do get occasional reception.
Thanks again for all of your help.
platypus25_5 said:
Alright, I've done this, I've also made a few different access point names for att to try and see if any of those have better reception. Nothing's working all that great, but hopefully at least one of them works a little better than what I've been used to.
Currently I still have no reception where I'm used to having one or two bars around the house. I'm not sure if there is anything else to do without opening up the phone and replacing any parts. If there is anything else you can think of that I might try, please let me know.
Do you think that changing the screen would make any difference on reception? I did have to have mine changed shortly after rooting the phone, but I can't really imagine that could be the cause since I still do get occasional reception.
Thanks again for all of your help.
Click to expand...
Click to collapse
Any hardware change could easily damage the antenna or it may be completely unplugged. Check the tear down video on ifixit
Sent from my ONEPLUS A6010 using Tapatalk
I am having the same problem after following the root guide - no data. I'm on T-Mobile with an ATT phone running H91010r. I installed your modem.bat file with my dumped modem files using twrp, I changed the ATT buildprop to open, rebooted and made sure to select the first auto option. I tried dialing the secret menu number but it gives an error. Zero data. Everything else seems to be working phone. Data worked on stock phone before rooting. Please help!
Classpro said:
I am having the same problem after following the root guide - no data. I'm on T-Mobile with an ATT phone running H91010r. I installed your modem.bat file with my dumped modem files using twrp, I changed the ATT buildprop to open, rebooted and made sure to select the first auto option. I tried dialing the secret menu number but it gives an error. Zero data. Everything else seems to be working phone. Data worked on stock phone before rooting. Please help!
Click to expand...
Click to collapse
it's most likely an APN problem
what do you mean the dialer code did not work ? it works on all H910
When I put in the dialer code and hit call I get "ussd code RUNNING" and then "connection problem or invalid mmi code"
I did get 4g working by reseting the Sim card, so I'm not panicking, but it seems slower than before. APN is off the t-mobile site.
Classpro said:
When I put in the dialer code and hit call I get "ussd code RUNNING" and then "connection problem or invalid mmi code"
I did get 4g working by reseting the Sim card, so I'm not panicking, but it seems slower than before. APN is off the t-mobile site.
Click to expand...
Click to collapse
are you sure you have a H910 ?
the dialer code depends on the Motherboard
*#546368#*910#
see the 910# at the end must match your phone
the Verizon LG V20 VS995 dialer code is disabled > worth reading
The unlocked LG V20 US995 would use dialer code *#546368#*995#
I'm not sure what works with the F800 version
clsA said:
are you sure you have a H910 ?
Click to expand...
Click to collapse
Yes, I'm sure. AT&T version, model number LG-H910. Running rooted software version H91010r.
I have the same problem on 800l entered the menu changing the model 996 at the end, as I understand it, without twrp how can I fix the problem?
Hi,
How can I recover from the settings of my android phone a APN password stored on an existing access point saved on my android Samsung work phone?
My device is not rooted and I cannot install app files outside of google store.
The APN is not readily available on the internet as is work
Appreciate advise on method could use to extract this password from the settings.
Would a backup of the device and then extracting the system directory to discover the apn config file work?
dreambro2 said:
Hi,
How can I recover from the settings of my android phone a APN password stored on an existing access point saved on my android Samsung work phone?
My device is not rooted and I cannot install app files outside of google store.
The APN is not readily available on the internet as is work
Appreciate advise on method could use to extract this password from the settings.
Would a backup of the device and then extracting the system directory to discover the apn config file work?
Click to expand...
Click to collapse
Edit: you should provide more info about the phone and android version if you want help
Thanks,
Its a Galaxy Cover 5 Android Version 11. One UI version 3.1
When go into Connections->Mobile Networks->Access point Names->Select the Apn->
There is a APN password already there and I want to copy this or reveal it.
Is this possible?
Thanks for your help