Does the Note 4 support ACA (Accessory Charging Adapter) to be able to charge the phone at the same time as using a usb OTG adapter?
I want to be able to use a USB DAC and charge the phone at the same time. Is this possible?
It's a very good question. I am curious about it as well.
I have 2 pieces OTG "Y" cable. 1 of them can to charge my phone but the phone can not recognize the usb flash drive. The other can not charge the phone but the phone can recognize the usb flash drive. I need a mixed cable from this 2 )
I need a quality OTG cable, any recommendations?
Related
Hello, we all know that there are USB OTG Cables with extra power plug (Y cable) but those are supposed to power external device like HDD, DVD, or anything what consumes more power than our android device can handle.
But my question is: is there any USB OTG cable with additional power plug but for simultaneous tablet / phone charging while USB stick is used?
I want to watch something long (i.e. TV Show series) from USB stick via OTG cable but I cannot simultaneously charge my tablet, so if it take too long my tablet will be out of power before I stop watching.
blackfire74 said:
Hello, we all know that there are USB OTG Cables with extra power plug (Y cable) but those are supposed to power external device like HDD, DVD, or anything what consumes more power than our android device can handle.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2617692
Roma-ES said:
http://forum.xda-developers.com/showthread.php?t=2617692
Click to expand...
Click to collapse
That means I have to add a resistor only to usb connector or just need a different kernel, or both?
On the native firmware say that this support function is disabled. Personally, I use this CivZ-FLEX-ЛУЧ-REV3.6.2 + SphereXtreme, where works flawlessly with OTG + charging resistor 64.9 K.
I call BS!!!!
I have a stock firmware, and have been using all kinds of USB cables. Found the best are made from Sony/Ericson and Blackberry. Once you have a quality cable your charging issues will go away.
Right now I am using a 7 foot cable that is from a Sony. No charging issues and works perfectly.
Lately I found another MHL cable 2hich is called HDMI to Micro HDMI, and that micro HDMI plug looks exactly like micro USB. Will such cable work with Note 8 properly without additional power?
The version of MHL our device supports requires a power source external to the tablet. That means the adapter itself needs to provide the power (battery or power adapter) or can pull enough off the HDMI cable, which is usually not enough juice to run the connection.
MicroHDMI and MicroUSB are also not physically compatible (won't fit the same port and different pin outs) even if they look so much a like. MHL typically uses MicroUSB at one end and full sized HDMI at the other.
Roma-ES said:
On the native firmware say that this support function is disabled. Personally, I use this CivZ-FLEX-ЛУЧ-REV3.6.2 + SphereXtreme, where works flawlessly with OTG + charging resistor 64.9 K.
Click to expand...
Click to collapse
This is correct u need to put a 63-65 k resistor between ground and Id pin(pin 4 &5) on USB connector. Doesn't work on civatos 4.4.2 as of now. USB host works fine with regular USB host cable but no charging when u use a y cable. I use civatos 4.2.2 kernel also. Works on yyks note 2 4.3 port also..
I have test multiple times. I use a USB dac in car and need charging and USB host.
what resistor should i use on my sghi257m samsung galaxy s4 mini otg usb cable?
on my dads galaxy s5 Active it shows message that says: Do you wanna enable power sharing
is that OTG? on my S4mini nothing pops up
I know this thread is really old but i want to use a USB DAC so need at cable with a resistor as mentioned above but What ROM should I use now?? also is there anywhere I can buy a cable with resistor in it or do i have to do it myself?
Hi,
I want to connect my NotePro to an external hard drive while charging it.
Do anyone knows how to do that?
wireless.tech.expert said:
Hi,
I want to connect my NotePro to an external hard drive while charging it.
Do anyone knows how to do that?
Click to expand...
Click to collapse
This: http://lavalink.com/products/samsun...bs-2/usb-otg-host-charge-adapter-tab4-tabpro/
Sent from my SM-P900 using Tapatalk
Thanks.
OTG + Charging cable
wireless.tech.expert said:
Hi,
I want to connect my NotePro to an external hard drive while charging it.
Do anyone knows how to do that?
Click to expand...
Click to collapse
OTG + Charging USB cable, find it on amazon: DECEC® Harrier Cable Portable USB 2.0 A Male to Micro B Data and OTG Cable USB Charge Cable
Dghan said:
OTG + Charging USB cable, find it on amazon: DECEC® Harrier Cable Portable USB 2.0 A Male to Micro B Data and OTG Cable USB Charge Cable
Click to expand...
Click to collapse
Unfortunately, this product actually does not allow the OP's device to simultaneously charge and act as the USB host device. The DECEC product has a switch for toggling between its two functions:
1. OTG Host Mode:Allows the OP's device to connect to USB peripheral (slave) devices and power them. This mode will also charge peripheral devices.2. Data Cable (Charge) Mode:Allows the OP's device to charge via an external power supply or via another USB host device (i.e., laptop).
Read the Q&A for this device on Amazon (go to Amazon and search for "Micro USB Male To USB Female Host OTG Cable + USB Power Cable Y Splitter"). The Q&A indicates that users have been able to use it for simultaneously charging a Nexus 7 and having the Nexus 7 act as a USB host device. One user mentioned that a custom kernel is needed to unlock this capability of the Nexus 7. They also recommended that a powered USB hub be used to ensure that the USB peripheral devices don't draw more power than the Nexus 7 can supply.
Current Limited to 1A
dodo99x said:
This: http://lavalink.com/products/samsun...bs-2/usb-otg-host-charge-adapter-tab4-tabpro/
Sent from my SM-P900 using Tapatalk
Click to expand...
Click to collapse
This adapter LIMITS THE CURRENT TO 1000mA as opposed to 1800mA using the 2.1A Samsung charger for TAB S 10.5. Presumably this would be the same for the Note 5 which comes with the higher capacity charger as well..
Hello,
I have the TF300T (without the keyboard dock), and I want to get a USB port dongle. However I have two needs:
I want the USB port to provide enough power for a USB 2.5" hard disk. I suppose I can use a powered USB hub for this?
I would really like to be able charge the tablet when the USB dongle is on. Is this possible?
Thank you
Evan_ said:
Hello,
I have the TF300T (without the keyboard dock), and I want to get a USB port dongle. However I have two needs:
I want the USB port to provide enough power for a USB 2.5" hard disk. I suppose I can use a powered USB hub for this?
I would really like to be able charge the tablet when the USB dongle is on. Is this possible?
Thank you
Click to expand...
Click to collapse
If that USB HDD requires 2 USB (one data one power), then a powered hub is your best bet.
When the USB dongle is in, it takes the place of the charging port. You can either charge the tablet or use the dongle.
Considering to use a Huawei Mediapad X2 7.0 for my 2DIN car install, since the dimensions of the tablet are nearly identical to 2DIN,
Therefore I would like to know if the device supports USB OTG Host mode and charging the battery of the mediapad simultaneously using a certain Y cable?
Thanks, much appreciated if you can give it a try!
FrankZZ said:
Considering to use a Huawei Mediapad X2 7.0 for my 2DIN car install, since the dimensions of the tablet are nearly identical to 2DIN,
Therefore I would like to know if the device supports USB OTG Host mode and charging the battery of the mediapad simultaneously using a certain Y cable?
Thanks, much appreciated if you can give it a try!
Click to expand...
Click to collapse
Not sure about OTG Host cum charging combination because my understanding if you use OTG Host mode very likely you plug in a USB OTG thumb drive meaning you cannot charge at the same time.
However connecting the X2 micro USB port via standard USB cable to my laptop, I noticed I could use it as an USB device and it charges at the same time albeit not as as fast as a dedicated charging.
kpcheang2 said:
Not sure about OTG Host cum charging combination because my understanding if you use OTG Host mode very likely you plug in a USB OTG thumb drive meaning you cannot charge at the same time.
However connecting the X2 micro USB port via standard USB cable to my laptop, I noticed I could use it as an USB device and it charges at the same time albeit not as as fast as a dedicated charging.
Click to expand...
Click to collapse
Yes, but not OTG.
I can confirm that, on my side, using an OTG hub with a external power plug, no way to have the device charged by external power when in OTG mode.
It is OTG or Normal charge and functions via USB.
Seems Logical because the Phone is supposed to provide the power to its USB accessories in OTG. Just my HUB has a switch that provide power to those accessories instead of the phone Itself. May-I add that switching this power button on the HUB does not function until you had unplugged & replugged the Hub in the phone after switching between the two modes. I'm afraid of the survival of the Micro USB plug of my phone, on the long run, with all those plugin, unplugin actions !!!
It's possible but with anothere Device the Nexus 7 (2012/2013) with Timurs Kernel. What's the difference of this kernel to the normal kernel, so OTG with charging is working for this device,too.
hI everyone in regard to otg using Usb and charging tablet at same time, I have a fusion5 tablet and a usb hub the kind with 3 usb hubs and a power in with a micro usb male plug. and a switch for otg or charge. Ive tried using a potentiometer to find the magic resistor value between pin 4 (the id ) and pin 5 ground of the micro plug.
(thought i had it at one point but not sure) as could play a avi file while charging) However now most of the timee either accesses the usb or charges, I can get it to do both , but stops charging after 8 seconds.
Anybody happen to know if a specific resistance value works for both charging and otg.
I have seen another schematic but havent tried it.
It doesn't sound like the micro usb otg cable to me. I built one without a resistor and mine works just fine. Have a look at your usb settings. Some devices require you select your choice: usb otg or charging.
nastiero said:
It doesn't sound like the micro usb otg cable to me. I built one without a resistor and mine works just fine. Have a look at your usb settings. Some devices require you select your choice: usb otg or charging.
Click to expand...
Click to collapse
Thanks How do I look at my usb settings?. I think I may not have the proper resistor setting as will currently provide power to usb and charge at same time for a few seconds then stops charging.. I turn resistance up it will charge , turn it down and will allow access to usb.. i think have to find that magic number inbetween.
jmxda21 said:
Thanks How do I look at my usb settings?. I think I may not have the proper resistor setting as will currently provide power to usb and charge at same time for a few seconds then stops charging.. I turn resistance up it will charge , turn it down and will allow access to usb.. i think have to find that magic number inbetween.
Click to expand...
Click to collapse
Depending on which phone and version of Android you have, the most recent versions of Android have the USB settings under Developers Options.
The USB OTG charging works differently from phone to phone. Sometimes you must plug your charger cable and the USB device you want to connect to into the OTG cable prior to plugging the OTG cable into your phone. This way the phone detects charging and device.
nastiero said:
Depending on which phone and version of Android you have, the most recent versions of Android have the USB settings under Developers Options.
The USB OTG charging works differently from phone to phone. Sometimes you must plug your charger cable and the USB device you want to connect to into the OTG cable prior to plugging the OTG cable into your phone. This way the phone detects charging and device.
Click to expand...
Click to collapse
Yes that is what I have been doing . In developer options under Usb default , no charge option there, only file transfer, USB tEThering, MID, PTP ,and o data transfer
I thanks. However i believe the default USB option is charge as thats what it is when i plug in USB to a powered cable.
. As I said jt works for A short time using USB and charging at same time with resistor between 45K and 68k
then either stops charging and continues usb or keeps charging but gives usb errrors or cant access usb but continues charging.
Fusion5 tablet android 9
Update this works fine with unmodified USB hub or charge power and USB on my LG k32 phone but not on the fusion ta blet.