Hi,
my GT-P3100 tablet keeps restarting after a few minutes.
So I tried to uninstall lastly installed app, but the device restarted every time I tried to do something with it - even a factory reset or opening the play store app. I also couldn't perform a factory reset form the recovery - it seemed like it was done ("Data wipe complete"), but it changed nothing. The next step I made was to flash a new firmware through Odin (3.09). The original firmware was 4.1.0, I flashed 4.2.2 - the whole process seemed to be OK, but an error occurred when the SYSTEM part was being flashed. I tried it 2 more times with the same result. Then I tried to root it with CF-Auto-root through Odin. The process was made successfully (as Odin wrote). The next step was to flash the CWM recovery (with hope that I will be able to perform a working factory reset). This was successful again, but the recovery didn't change.
AFTER ALL THIS STEPS I HAVE THE SAME LOOKING SYSTEM - with all apps, same restart problem,... It seems like it is protected against writing/deleting of anything.
I would be really thankful, if anybody gives me an advice what to do...
Thank you very much.[/QUOTE]
So I tried to my Samsung galaxy Tab 2 GT-P3100.
1. Tried to uninstall software, but it's restore again after every reboot.
2. Tried to delete some Images, video and sms but again it restart and restore.
3. Tried using safe mode but nothing changed.
4. Tried to wipe data/factory reset using system recovery. when I entered recovery menu some massage shown at bottom
Applied the CSC-code: TMZ... did not match sized '/system/csc/common/system/csc/default_workspace.xml' (No data available)
5. Flash ROM with odin 3.09 but it failed at 50%, but nothing changed.
6. Flash ROM using ADB bootloader, but nothing changed.
7. Flash rom from sd card, but nothing changed.
8. Tried to flash a CWM, TWRP recovery image, via fastboot, ADB, SD card, odin, but nothing changed.
9. Flash ROM with Heimdall (Heimdall is a cross-platform open-source tool suite used to flash firmware (aka ROMs) onto Samsung mobile devices).:crying:
10. When I went to the service center they suggest me replace motherboard. (cost Rs. 7500/-)
any suggestions are welcome
Hi
Thanks for writing to us at XDA Assist. I can see you've posted the same topic in this thread. Please refer to the XDA forum rules for information on creating duplicate posts. I'm going to let the good folks of the Galaxy Tab 2 forum continue to help you out.
Good luck!
Thread closed.
Related
So, friend of mine tried to update his Telenor Serbia tab from HC to ICS via kies, it offered upade, he tried, and finished being stucked with samsung galaxy tab 7.7 logo.
Tab can enter both to download mode or recovery.
He gave to me and what I did so far is this:
- First, downloaded LQG and installed via odin, but tab is still stucked.
- I installed CWM 6.0.2.3 and tried to wipe data, but it refuses to wipe, it kind of starts, but reset immediately.
- Downloading LA4 (HC) rom to instal via odin and try to wipe from custom recovery, same result, actualy, it refuses to enter factory recovery, it says "updating aplication".
- Installed Touch recovery TWRP 2.4.0.0. but it wont even enter it.
- Now I am trying with some LQG_BLG ICS rom, and ig it fails, I'll try with Open Austria rom.
Any other ideas? Do I have to repartition data or it still can be restored?
UPDATE: I have managed to restore it via double flashing LQC_BLG rom that bassem.mohsen here. One time was not enough, but twice with not allowing it to boot, before the second time.
I have installed CWM after so I don't have issues with mmc, and that's it.
djurkash said:
So, friend of mine tried to update his Telenor Serbia tab from HC to ICS via kies, it offered upade, he tried, and finished being stucked with samsung galaxy tab 7.7 logo.
Tab can enter both to download mode or recovery.
He gave to me and what I did so far is this:
- First, downloaded LQG and installed via odin, but tab is still stucked.
- I installed CWM 6.0.2.3 and tried to wipe data, but it refuses to wipe, it kind of starts, but reset immediately.
- Downloading LA4 (HC) rom to instal via odin and try to wipe from custom recovery, same result, actualy, it refuses to enter factory recovery, it says "updating aplication".
- Installed Touch recovery TWRP 2.4.0.0. but it wont even enter it.
- Now I am trying with some LQG_BLG ICS rom, and ig it fails, I'll try with Open Austria rom.
Any other ideas? Do I have to repartition data or it still can be restored?
UPDATE: I have managed to restore it via double flashing LQC_BLG rom that bassem.mohsen here. One time was not enough, but twice with not allowing it to boot, before the second time.
I have installed CWM after so I don't have issues with mmc, and that's it.
Click to expand...
Click to collapse
thanks for the up-date.. This sounds like a breakthru that alot of people (like me) could use...
Most that are stuck at boot loop...
ONE thing though....
you said in part.... " twice with not allowing it to boot, before the second time. "
Now can you elaborate on your 'timing' on when to push the start button again on Odin on the second flash..
Ive read this once before....
BUT... I think we need a specific instruction on the exact timing.. on WHEN to flash the second time.... what should be showing on our screens when we hit Odins start button for the second flash.....
Please instruct us on exactly when to flash the second time.... thanks alot....
Have a Verizon Samsung Galaxy Note II (SCH-i605). Took the latest OTA update to VRUEMJ9. Have since rooted and installed SafeStrap and was happily running N3BULA ROM, when I decided to explore a bit and tried to flash Alliance ROM. Now I'm stuck on the Samsung boot screen and can go no further. I am able to access Android system recovery, but when I try to 'apply update from external storage' I get 'E:signature verication failed' message. Tried to flash to stock via Odin, but unsuccessful. Shows Added in Odin but nothing happens when I select the .pit file or the .tar file. This is a work issued phone, so any help to get up and running would be greatly appreciated!
Brantosapien said:
Have a Verizon Samsung Galaxy Note II (SCH-i605). Took the latest OTA update to VRUEMJ9. Have since rooted and installed SafeStrap and was happily running N3BULA ROM, when I decided to explore a bit and tried to flash Alliance ROM. Now I'm stuck on the Samsung boot screen and can go no further. I am able to access Android system recovery, but when I try to 'apply update from external storage' I get 'E:signature verication failed' message. Tried to flash to stock via Odin, but unsuccessful. Shows Added in Odin but nothing happens when I select the .pit file or the .tar file. This is a work issued phone, so any help to get up and running would be greatly appreciated!
Click to expand...
Click to collapse
Have you performed a "wipe data" option from the recovery after flashing the alliance ROM (it wipes your user data)?
Because I just visited the alliance ROM thread ( http://forum.xda-developers.com/showthread.php?t=2032447 and in the install instructions its mentioned so.
Better take a little time and properly read the install instructions during flashing..
Sent from my GT-I9070 using Tapatalk
dagger said:
Have you performed a "wipe data" option from the recovery after flashing the alliance ROM (it wipes your user data)?
Because I just visited the alliance ROM thread ( http://forum.xda-developers.com/showthread.php?t=2032447 and in the install instructions its mentioned so.
Better take a little time and properly read the install instructions during flashing..
Sent from my GT-I9070 using Tapatalk
Click to expand...
Click to collapse
I never had that option. I've flashed numerous ROMS before and am pretty meticulous when it comes to following instructions. It appeared to have a custom flash script which allowed me to pick what I did and didn't want to install. I tried to keep it mostly stock and when it completed, it automatically rebooted (didn't give me an option to 'wipe data') and now leaves me stuck on the Samsung Boot Screen. I was able to flash the .pit file via Odin, but keep getting a 'MD5 hash value is invalid' when I try to flash the .tar file.
Brantosapien said:
I never had that option. I've flashed numerous ROMS before and am pretty meticulous when it comes to following instructions. It appeared to have a custom flash script which allowed me to pick what I did and didn't want to install. I tried to keep it mostly stock and when it completed, it automatically rebooted (didn't give me an option to 'wipe data') and now leaves me stuck on the Samsung Boot Screen. I was able to flash the .pit file via Odin, but keep getting a 'MD5 hash value is invalid' when I try to flash the .tar file.
Click to expand...
Click to collapse
You should enter into recovery and then manually wipe data..
Also if that thing doesnt work, then have a look at this thread which explains how to go back to stock rom..
In addition,
A. Why doesnt Odin work?
Did you unextract the tar and pit from the rar/zip so that odin could recognize the files as suggested in dagger's link in section 1b step 2?
Did you install samsung drivers on your computer properly? You may use this toolkit for that
B. Rescue by CWM
Signature verification failed is caused (I think) by stock samsung recovery's choosiness, if you are sure you downloaded the zip correctly. What zip did you exactly try to flash?
So now, you may want to flash a cwm recovery or a kernel that contains cwm inside. Flashing usually uses adb using fastboot. Search "flashing a recovery image" or "flashing a kernel" where your chosen kernel should have cwm inside. cwm usually does not put out that signature verification error.
Remember:
You can access recovery mode through an app or by pressing a button combo when turning your phone on. Device specific.
Stock samsung recovery can wipe data.
CWM can also wipe data, and is the preferred installation method for most/all custom roms. And it can make a nandroid backup.
If ever you do choose to flash, you'll need the toolkit to install adb/fastboot drivers, but maybe since yours in locked bootloader the adb thing might not work.
Hope this helps
It turns on for a few seconds and then turns off again. I tried everything that I could think of.
1. I tried Clearing the Cache using recovery mode but it only say "Error"
2. I tried Factory data reset. It says Successful but when i hit reboot. nothing has changed, all my apps are still there. and my tab kept restarting.
3. I tried flashing cwm using odin (hoping that i could install a custom rom) i said pass but when i boot into recovery mode, it is just stock recovery not cwm.
4. I also tried uninstalling apps (hoping that something will change) but alas! when my tab restarts, the apps i did install is still there...
5. Finally, I tried flashing stock rom using odin but to my suprise, rom flashing will fail halfway...
Im out of options. please tell me what to do..
XDA Visitor said:
It turns on for a few seconds and then turns off again. I tried everything that I could think of.
1. I tried Clearing the Cache using recovery mode but it only say "Error"
2. I tried Factory data reset. It says Successful but when i hit reboot. nothing has changed, all my apps are still there. and my tab kept restarting.
3. I tried flashing cwm using odin (hoping that i could install a custom rom) i said pass but when i boot into recovery mode, it is just stock recovery not cwm.
4. I also tried uninstalling apps (hoping that something will change) but alas! when my tab restarts, the apps i did install is still there...
5. Finally, I tried flashing stock rom using odin but to my suprise, rom flashing will fail halfway...
Im out of options. please tell me what to do..
Click to expand...
Click to collapse
Hi, thanks for using XDA assist!
First, please create an account so you can post in other forums.
After creating your account, please ask your question here:
http://forum.xda-developers.com/galaxy-tab-2/help
Also, you should bookmark this for future reference:
http://forum.xda-developers.com/galaxy-tab-2
That's where you'll find anything and everything for your device.
Good luck!
Phone Info:
Samsung Galaxy s5 (sm-g900p) (Sprint)
Android Version 5.0
Build: LRX21T.G900PVPU1BOA6
Hi, Thank you ahead of time to anyone who might have a minute to help me out. I have been combing XDA and as well as some other sites trying to find a solution myself but given my limited experience in this area Im at the point where I thought it best to stop and ask for help rather than do the wrong thing and have my phone blow up in my hands TNT style
I rooted my s5 a few weeks ago using Odin with C-f--auto-root, which went perfectly and I had zero issues afterwards.. This was only my second rooted device so of course I was exploring all of my new options out there to customize my phone.
The problem occurred after installing the apps Layers Manager and Layers Showcase (BitSyko Development) from the Playstore. Both seem like great apps and were not to blame for this problem, I just happened to be using them when I jacked something up.
Basically, over a day or two I tried several Layers Themes and they applied just fine, but one did not. Shortly after applying the Layer, and rebooting my phone I ended up on the bright Yellow Sprint Spark startup screen and my phone wont budge past this point.
I am able to boot into Recovery Mode as well as Download mode. I tried wiping the cache Partition as i had read to do as well as doing a full data clear and reset ,but it still; wouldnt move past the yellow screen. Then I very carefully followed directions to flash the stock firmware using Odin, making sure i used the right one for this phone and Odin displayed PASS! at the end. From what i could tell, it all went fine... But it STILL wont move past that enraging yellow screen!!
I think I may have missed something in regards to flashing stock firmware but i dont know. Ive read some other suggestions and things to try but, like i said, at this point and with my limited experience, I thought it best to concede and ask the experts for some help.
I hope I included any information needed...
Are you waiting long enough to allow for loading? Did you try installing a stock rom that matches bootloader version?
gdrocks said:
Are you waiting long enough to allow for loading? Did you try installing a stock rom that matches bootloader version?
Click to expand...
Click to collapse
Hi, thank you for your reply. Yes, the stock rom i used matched the original rom on the device. I had taken some screen shots of the Device Info screen a while back for something else, so luckily i had a lot of general info right there shot the s5. And i waited a good amount of time. Odin took a few minutes and it read PASS at the end. From what i could tell, it was all done and i still waited just to be sure. But the more i think about it, the more i feel that i did do something wrong at this step. I'm just not certain what
Amandajbee86 said:
Hi, thank you for your reply. Yes, the stock rom i used matched the original rom on the device. I had taken some screen shots of the Device Info screen a while back for something else, so luckily i had a lot of general info right there shot the s5. And i waited a good amount of time. Odin took a few minutes and it read PASS at the end. From what i could tell, it was all done and i still waited just to be sure. But the more i think about it, the more i feel that i did do something wrong at this step. I'm just not certain what
Click to expand...
Click to collapse
Flash the TWRP recovery in odin
After that enter in recovery mode and format system, data, cache, dalvik cache, sdcards.
Then put the phone into download mode, and flash with odin the last stock rom (OG1) but make sure you don't have selected the "reboot" option in odin
After you got your phone flashed, take the battery out put it again and enter in recovery mode, choose "wipe data/factory reset"
Then put your phone in download mode and flash again the stock rom (OG1) this time with the "reboot" option selected
After you flashed your phone the first boot takes some minutes (in the yellow screen), just be patient.
After this you should have your phone complety clean and your problem solved.
DOWNLOADS
Odin 3.10.7
Stock Rom OG1
TWRP 2.8.7.0
daniel3x said:
Flash the TWRP recovery in odin
After that enter in recovery mode and format system, data, cache, dalvik cache, sdcards.
Then put the phone into download mode, and flash with odin the last stock rom (OG1) but make sure you don't have selected the "reboot" option in odin
After you got your phone flashed, take the battery out put it again and enter in recovery mode, choose "wipe data/factory reset"
Then put your phone in download mode and flash again the stock rom (OG1) this time with the "reboot" option selected
After you flashed your phone the first boot takes some minutes (in the yellow screen), just be patient.
After this you should have your phone complety clean and your problem solved.
Click to expand...
Click to collapse
Thank you so much! I am going to give this a try hopefully tonight, or in the morning if I cant make time tonight. I will report back once I do. Again, thank you so much for taking the time to help me out. It really means a lot! :fingers-crossed:
i had the same problem and tried over 10 other ways to fix it. i finally found this post and it worked! ty so much. was almost ready to throw the phone out
daniel3x said:
Flash the TWRP recovery in odin
After that enter in recovery mode and format system, data, cache, dalvik cache, sdcards.
Then put the phone into download mode, and flash with odin the last stock rom (OG1) but make sure you don't have selected the "reboot" option in odin
After you got your phone flashed, take the battery out put it again and enter in recovery mode, choose "wipe data/factory reset"
Then put your phone in download mode and flash again the stock rom (OG1) this time with the "reboot" option selected
After you flashed your phone the first boot takes some minutes (in the yellow screen), just be patient.
After this you should have your phone complety clean and your problem solved.
DOWNLOADS
Odin 3.10.7
Stock Rom OG1
TWRP 2.8.7.0
Click to expand...
Click to collapse
see, nw this is the type of post i like to see!! @daniel3x , for future reference, idoneapps.com has WAAAAAAY faster downloads then sammobile and the tar.md5 files are 100% legit! But youre reply is pretty much exactly what i would have said. I personally would have advised on OK4 vs OG1. OK4 is just easier to mess with on TWRP and stuff.
wait a while for first stock boot from yellow screen
I've read that flashing a stock firmware will take 10 to 20 or more minutes on your first boot. Let the heat sink from your body and give it time.
I want to flash to a stock as well. Can I just full system wipe in twrp and Odin og1 or ok4>what I'm currently on and would like to keep it? Should I take out my SIM? Should I take out my sd card? Will I need to re partition my ext2/4 on the sd? Does the stock image replace the bootloader? I have a twrp backup on my extsd, can I use it after attempting to flash stock? Flash stock tar/zip should stock be a tar?, Odin kltespr twrp in pda mode, leave everything alone, root method of choice, phh su so flash in twrp, should I update Odin? I have 3.07 and 3.10.6. Then wait out that initial boot. I don't want a backup of what I have now because I've done things I wantedd to revert and do differently this time as I'm not AS clueless
Amandajbee86 said:
Phone Info:
Samsung Galaxy s5 (sm-g900p) (Sprint)
Android Version 5.0
Build: LRX21T.G900PVPU1BOA6
--SNIP--
I hope I included any information needed...
Click to expand...
Click to collapse
Oh, some app permissions can cause a bootloop. Instead of flashing the whole stock rom, you can flash the recoveries through odin.
You can either:
-Flash stock recovery through Odin (BL slot) and perform a factory reset/cache wipe
-Go through TWRP and restore your backup
-Go through TWRP and wipe your cache partitions on ADVANCED WIPE
SAMSUNG S5 SPRINT STOCK RECOVERIES:
mega(DOT)nz/#!bRxE1QRD!1-mAR_T6tvb-83xohTD6Q8uNxW4TdpcqnDT3Uq6s5ms
mega(DOT)nz/#!mEwQCDrS!I8pGn8Wa4TSlCpsazD2_ZOh7t1r9sy5kJZ_ujk6viOY
Bl is the recovery? Odin can't flash a bootloader?
This salvaged my sprint phone
I had to flash back from LineageOS 14.1 to stock rom temporarily to "update profile" so I could make phone calls again after moving the phone to a new line. I tried several different versions of stock rom and flashed via ODIN, but all got stuck on the boot loop. It felt like I had searched endlessly for a solution until I came across this thread. I followed the process (Thank you @daniel3x & @youdoofus) using the stock rom ending in OK4; it worked flawlessly!
If possible, I would like to see this thread "stickied" for Sprint Galaxy S5. It will likely save other users a lot of time.
:good: :victory:
kentc said:
I had to flash back from LineageOS 14.1 to stock rom temporarily to "update profile" so I could make phone calls again after moving the phone to a new line. I tried several different versions of stock rom and flashed via ODIN, but all got stuck on the boot loop. It felt like I had searched endlessly for a solution until I came across this thread. I followed the process (Thank you @daniel3x & @youdoofus) using the stock rom ending in OK4; it worked flawlessly!
If possible, I would like to see this thread "stickied" for Sprint Galaxy S5. It will likely save other users a lot of time.
:good: :victory:
Click to expand...
Click to collapse
glad to help
Samsung Galaxy Tab 2
GT-P5110
Android version: 4.2.2.
Hi there, I have a rooted device running on CyanogenMod 10.1.3-p5110, with a custom recovery CWM 6.0.2.7
After 3 years (or so) of smooth operation it started to slow down and getting unstable from time to time, so I decided to factory reset.
I did the factory reset from CWM following the regular regular instructions, however after reset completion the devices booted back to the original CM10, with all the original data (nothing was cleaned at all or reset). I tried several times from - cleaning cache, date, system, dalvik cache, factory reset ... still the same result.
I also tried to replace the CWM with TWRP (GT-P5110_TWRP_3.0.0-0.tar.md5) - same result, it shows success but if I restart to recovery, it goes to CWM 6.0.2.7
If I boot into recovery (CWM) and flash any rom, it shows success and then reboots (guess what) into the original CM 10 like nothing happened.
I tried to flash the stock firmware using Odin. I got an original firmware "P5110XXDMI1_P5110OXXDMJ1_HOME.tar.md5" from a reliable source (sammobile)
Model:GT-P5110, Model name:GT-P5110, Country:Czech Republic, Version:Android 4.2.2, Changelist:1709803, Build date:Wed, 18 Sep 2013 06:13:11 +0000, Security Patch Level: N/A, Product code:XEZ, PDA: P5110XXDMI1, CSC5110OXXDMJ1
Every time I flash the original stock rom with Odin, the ID:COM box in Odin goes green and everything looks just fine but after reboot the tablet restarts to the original CM10. I was using Odin3-v1.85, as well as newer versions of the tool - namely Odin3_v3.07, Odin3_v3.11.1, all with the same result.
I even tried form very scratch - repartitioning the device using a .pit file "signed_espresso_20120220_16G.pit", flashing stock using Odin, same result.
I also tried flashing rom Heimdall Suite - same result
I have no problem to connect to the device using ADB shell and communicate with the device ...
However, I am not any Android guru, so I cannot "decode" what I get.
To me it seems like I somehow messed up my partitions or mounts and thats the reason for the strange behaviour.
So now I am stuck in strange state, which I cannot call a bootloop ... seems like I am running some sort of cached system or someting and I am unable to get out of with any standard tool available. As I said ... device is rooted, running CWM and I can boot to any mode I want ... download, recovery, system.
Any help will be more than appreciated.
You could have an faulty emmc firmware or your emmc reached end of life.
You are from europe? I know someone who can fix it for you.
You can also read the faq on my github userpage for more information about your bug.
kozyn said:
Samsung Galaxy Tab 2
GT-P5110
Android version: 4.2.2.
Hi there, I have a rooted device running on CyanogenMod 10.1.3-p5110, with a custom recovery CWM 6.0.2.7
After 3 years (or so) of smooth operation it started to slow down and getting unstable from time to time, so I decided to factory reset.
I did the factory reset from CWM following the regular regular instructions, however after reset completion the devices booted back to the original CM10, with all the original data (nothing was cleaned at all or reset). I tried several times from - cleaning cache, date, system, dalvik cache, factory reset ... still the same result.
I also tried to replace the CWM with TWRP (GT-P5110_TWRP_3.0.0-0.tar.md5) - same result, it shows success but if I restart to recovery, it goes to CWM 6.0.2.7
If I boot into recovery (CWM) and flash any rom, it shows success and then reboots (guess what) into the original CM 10 like nothing happened.
I tried to flash the stock firmware using Odin. I got an original firmware "P5110XXDMI1_P5110OXXDMJ1_HOME.tar.md5" from a reliable source (sammobile)
Model:GT-P5110, Model name:GT-P5110, Country:Czech Republic, Version:Android 4.2.2, Changelist:1709803, Build date:Wed, 18 Sep 2013 06:13:11 +0000, Security Patch Level: N/A, Product code:XEZ, PDA: P5110XXDMI1, CSC5110OXXDMJ1
Every time I flash the original stock rom with Odin, the ID:COM box in Odin goes green and everything looks just fine but after reboot the tablet restarts to the original CM10. I was using Odin3-v1.85, as well as newer versions of the tool - namely Odin3_v3.07, Odin3_v3.11.1, all with the same result.
I even tried form very scratch - repartitioning the device using a .pit file "signed_espresso_20120220_16G.pit", flashing stock using Odin, same result.
I also tried flashing rom Heimdall Suite - same result
I have no problem to connect to the device using ADB shell and communicate with the device ...
However, I am not any Android guru, so I cannot "decode" what I get.
To me it seems like I somehow messed up my partitions or mounts and thats the reason for the strange behaviour.
So now I am stuck in strange state, which I cannot call a bootloop ... seems like I am running some sort of cached system or someting and I am unable to get out of with any standard tool available. As I said ... device is rooted, running CWM and I can boot to any mode I want ... download, recovery, system.
Any help will be more than appreciated.
Click to expand...
Click to collapse
Once I had same problem with Motorola xoom and guess what was realy the problem. It was the external SD memory remove it then flash the stock rom.. If problem persists see with Andi
Thank you for your response. To me it also seems like faulty emmc. I have check the frequently asked questions on your blog and the description there exactly matches with what I'm experiencing on my device. Yes I am from Europe, Czech Republic. I have already tried to get in touch with two people who have the proper tooling to flash the firmware (JTAG). Hope I get some response fast and the solution is going to work. Still if you have someone in the CZ that you can recommend I'm grateful for any advice.
@zidane: All of the above steps where performed without external SD card.
kozyn said:
@zidane: All of the above steps where performed without external SD card.
Click to expand...
Click to collapse
Don't lose hope Try latest recovery 3.0.2.5 and the cm13 22/9 by Andi (made specially for certain cases like yours the files are in his folder the link in his signature ) if nothing happens then I guess dev Andi will be glad to help you fix your Emmc. contact him to provide you with the contacts..
Good luck
zidane01 said:
Don't lose hope Try latest recovery 3.0.2.5 and the cm13 22/9 by Andi (made specially for certain cases like yours the files are in his folder the link in his signature ) if nothing happens then I guess dev Andi will be glad to help you fix your Emmc. contact him to provide you with the contacts..
Good luck
Click to expand...
Click to collapse
@zidane01: thanx for cheerin' up
I have tried to replace my CWM 6.0.2.7 with TWRP 3.0.2.5, 3.0.2.6. from a .zip file using current recovery. Result is the same as described - after I reboot to recovery (using advanced option in CWM) it boots back to the original CWM 6.0.2.7. Flashing latest CM13 (as of 27/9/2016, downloaded from Andi's site) from CWM 6.0.2.7 ends with error. The tablet seems like READ ONLY not matter what I do. Maybe I am doing something wrong. I can describe the procedure step by step in detail, if you wish.
kozyn said:
@zidane01: thanx for cheerin' up
I have tried to replace my CWM 6.0.2.7 with TWRP 3.0.2.5, 3.0.2.6. from a .zip file using current recovery. Result is the same as described - after I reboot to recovery (using advanced option in CWM) it boots back to the original CWM 6.0.2.7. Flashing latest CM13 (as of 27/9/2016, downloaded from Andi's site) from CWM 6.0.2.7 ends with error. The tablet seems like READ ONLY not matter what I do. Maybe I am doing something wrong. I can describe the procedure step by step in detail, if you wish.
Click to expand...
Click to collapse
sounds like that you have a faulty emmc. same what android-andi said.
@kozyn Hi buddy.. have the same thing on a p5110 -- emmc is in read only mode and I can't seem to PM Andi for some contacts.
Can you help me recover this galaxy tab2 pls? Appreciate your time