Database Info

Need Help to Revive My Dead Xperia M2

Hello
Recently i flashed my m2 with latest lollipop frimware with flashtools, i just excluded "userdata" and "cache" to save my data on the phone BUT after a full flash progress i ended up with a almost dead phone.
no flashmode,fastboot or any indicator led
when i connect the cable flashtool says:
"Device connected with USB debugging off
For 2011 devices line, be sure you are not in MTP mode"
I think whole boot section wiped , Any idea what should i do ?
and by the way any one knows where is the test point on its board ?
Thanks in advance

mory_zh said:
Hello
Recently i flashed my m2 with latest lollipop frimware with flashtools, i just excluded "userdata" and "cache" to save my data on the phone BUT after a full flash progress i ended up with a almost dead phone.
no flashmode,fastboot or any indicator led
when i connect the cable flashtool says:
"Device connected with USB debugging off
For 2011 devices line, be sure you are not in MTP mode"
I think whole boot section wiped , Any idea what should i do ?
and by the way any one knows where is the test point on its board ?
Thanks in advance
Click to expand...
Click to collapse
Try to reboot the phone by holding 10sec vol+ and Power keys when the phone is plugged. Your phone should reboot in fastboot mode and then unplug and it should be powered off.

If you coming from KK to LP do fresh install with wiping everything.
Good Luck.
Sent from my D2303 using Tapatalk

tromine said:
Try to reboot the phone by holding 10sec vol+ and Power keys when the phone is plugged. Your phone should reboot in fastboot mode and then unplug and it should be powered off.
Click to expand...
Click to collapse
Nothing Happens

mory_zh said:
Nothing Happens
Click to expand...
Click to collapse
There's a hole by the sim card, press it with some sharp pin (i use paperclip) then hold volume down connect to usb, you should connect in Flashmode.
Good Luck.
Sent from my D2303 using Tapatalk

Hello.
I have the same problem, any solution?

Try doing a software repair via sonys pcc see if this helps, you should always wipe the phone clean when using flashtool to avoid any problems
D2303 5.1 customised NCB LB rooted Nuts t2u dual recovery bravia engine+x-reality debloated

[email protected] said:
Try doing a software repair via sonys pcc see if this helps, you should always wipe the phone clean when using flashtool to avoid any problems
D2303 5.1 customised NCB LB rooted Nuts t2u dual recovery bravia engine+x-reality debloated
Click to expand...
Click to collapse
pls can u provide flash tool ?

XDADEVX said:
pls can u provide flash tool ?
Click to expand...
Click to collapse
XDA have pretty good search engine, try it.
Sent from my D2303 using Tapatalk

Dzepar said:
XDA have pretty good search engine, try it.
Sent from my D2303 using Tapatalk
Click to expand...
Click to collapse
Revived M2 thnx

mory_zh said:
Hello
Recently i flashed my m2 with latest lollipop frimware with flashtools, i just excluded "userdata" and "cache" to save my data on the phone BUT after a full flash progress i ended up with a almost dead phone.
no flashmode,fastboot or any indicator led
when i connect the cable flashtool says:
"Device connected with USB debugging off
For 2011 devices line, be sure you are not in MTP mode"
I think whole boot section wiped , Any idea what should i do ?
and by the way any one knows where is the test point on its board ?
Thanks in advance
Click to expand...
Click to collapse
Did anyone come up with a solution for this? I have the exact same problem right now. Tried the little button near the SIM card slot, tried charging. Phone won't boot into flashmode, or fastboot. No LED-s flash at all.

Donwlaod flashtool and choose flash mode then press vol down and connect it to computer. Without enabling USB debugging also it will go into flash mode. Then jusy flash kitkat or lolipop and dont forget to wipe data this time

Sudin said:
Donwlaod flashtool and choose flash mode then press vol down and connect it to computer. Without enabling USB debugging also it will go into flash mode. Then jusy flash kitkat or lolipop and dont forget to wipe data this time
Click to expand...
Click to collapse
The phone WILL NOT go into flash mode nor fastboot. No LED-s blink when trying to do so, nothing happens when I connect the charger or press the power button.

Try having a good read through this thread it may be of some help.
http://forum.xda-developers.com/showthread.php?p=38567003
When using flashtool always best to wipe cache and user data to avoid problems especially when going from kk to lollipop and vice versa a clean wipe n install always works wonders also use 9.18.6 or older version of flashtool they work better. Also try leaving it on charge over night
D2303 5.1lollipop customised NCB LB rooted Nuts t2u dual recovery bravia engine 2+x-reality debloated viper audio

Sony Xperia E3 Bricked

I tried to put AOSP 5.1 from FXP in my phone, and my cellphone bricked. It wont turn on, it keeps the Sony Logo 2 seconds. It haven't connection with flashtool. Please Help me.

Hi. Can you give me more information what you did exactly step by step. So maybe i can help you. My E3 was bricked too. I found a solution. But i need more information.

Flash stock rom it'll unbrick it

#4
Thank you answer back! I did exactly the following:
The model is my Xperia E3 D2212 dual sim.
- Unlocked the bootloader, :laugh:
- CWM installed a custom recovery, :laugh:
- I reinstalled the original rom, :laugh:
- I made a backup of the entire system using CWM.
And everything went super normal way, without complications.
The mistake was when he wanted to installing a custom ROM called "AOSP_L_MR1_150718_flamingo" because I found out later that he had not read that it was for ANOTHER XPERIA as follow the you tube tutorial . The ROM's for another Xperia, if I remember correctly.
After doing the installation process of the new AOSP ROM, the phone is less than a minute on the logo of SONY XPERIA down with, looped, can not enter the bootloader, and no longer recognizes the PC. I can not recognize it at FlashTool. I think that's all. :crying:
I greatly appreciate your attention.
I ended up editing this text in the google translator, then I'm sorry, if you are not very good.
Thank you

Matteus Maximo Felisberto said:
I tried to put AOSP 5.1 from FXP in my phone, and my cellphone bricked. It wont turn on, it keeps the Sony Logo 2 seconds. It haven't connection with flashtool. Please Help me.
Click to expand...
Click to collapse
Someone can help me please?

nibeal said:
Hi. Can you give me more information what you did exactly step by step. So maybe i can help you. My E3 was bricked too. I found a solution. But i need more information.
Click to expand...
Click to collapse
Could you help me? I can not make the pc recognize him ... He barely turns on and off since. The PC Companion software tells recognize it, but when you are installing the software says "it is not possible for this phone is changed." I can not scessar the bootloader does not give time and it shuts down.

Thanks, my error was with the fastboot driver and adb in flashtool. The Windows drivers wasn't been recognized, I've to install the drivers, all of they. After this, I Flashed the Stcok ROM, installed SuperSU and Restored the backup, everything works fine and fluid now. Thanks, anyway, for encouraging me.

I flashed my D2203 back to factory rom yesterday using Flashtool (flashtool.net/downloads.php) on Windows 7 PC.
How did I do it:
1) Install flashtool
2) Install Flashtool-drivers.exe from flashtool subfolder /drivers and select flashmode and fastboot drivers.
3) Run Flashtool and open XperiFirm (letters XF on logo)
4) Select Xperia E3 Flamingo -> proper D22** you have -> Market -> and select latest release below PayPal logo
5) Press "Download" and wait for download and unpacking
6) Switch off phone (if power on/off button does not respond then open back cover and push "OFF" by using pen)
7) Press and hold volume down button and connect phone to PC using original USB cable
8) Using Flashmode flash device

I have hard bricked a Xperia M2. Help please.

I think I was not suppose to do a full factory reset and then flash Cyncyanogen 12.1. Can this phone still be fixed?

I should have realised that I could not flash non stock custom ROMS when my device cannot be unlocked. I should have downloaded Z5 style in Android development.

droyjul said:
I think I was not suppose to do a full factory reset and then flash Cyncyanogen 12.1. Can this phone still be fixed?
Click to expand...
Click to collapse
Dis you try to flash original ftf for your model ?

It is fine now

Gauravs deodexed z2 port works well aswell.
D2303 5.1 deodexed z2 port+z5+X apps+themes, be,xr,sv,ad,XZRt2urecovery,xposed,z5 cam2.0,xLOUD,S-Force,viperaudio+more

I hard bricked my phone for 2 times but I managed to fix it
REQUIREMENTS
Usb debugging should be on
Xperia M2 stock ftf
Pc companion
Flashtool
First install the right usb driver for your phone downloadad install Pc Companion same as Flash tool get a pin and press the OFF butto near sim card slot for 5secs after charge it for 1 hour you should see a red led while charging. And then remove the charger and plug the usb cable I know that it can't be recognize but there's a way. Press the OFF button near sim card slotfor 5secs press the powerbutton and volume down at same time open Pc Companion wait for Pc Companion to recognize and release the 2 button eait for Pc Companion to recognize your phone don't release it yet if Pc Companiom didn't recognize try it again. Then go to flashtool click the lightning logo or button whatsover click flashmode click te 3 dots find where you put the stock ftf flash and wit for fastboot message then press the 2 button again wait for PcCompanion to recognize it and taraaa done.
Xperia m2,deodedexed,xposed,2.0 cam,themes,x reality,xperia 4.6 style,modded buildprop tweaks and more..

Xperia Z3 stuck at SONY logo has TWRP but no OS Installed

Hey Guys,
I'm not sure if this issue has been solved, but I was kinda clumsy when i tried to install superSU.zip via twrp (I have TWRP 3.0.2-0)and my Z3 still turns on but wont go to the home screen. I tried downloading the stock firmware and used flashtool but I can't get my phone to flashmode via volume down and plugging it. When I plug it on my laptop (windows 10) while holding any button it shows me the sony logo and nothing happens, no lights. so I turn off the device via the emergency button and holding it down for a few seconds. Good thing is im still able to go to TWRP via turning the phone on and waiting for the purple LED and pressing the volume up and down.
I tried looking for a back up file for my Z3 d6603 and planning to put it on my SD card and restore via TWRP. is my phone really dead? I'm not losing hope yet since i can still charge my phone (i dont see the battery icon though) but it charged from 70 to 83 while plugged in without the red LED and the battery logo.
Can someone please help me with this dilemma? I cant find the right keywords for this problem using google. any help will be much appreciated guys!

bootloop solution
Hello, regarding your question ami happened to me several times when trying to root my old good z1 what you can do if you did not make a backup of your rom, you must have Sony PC Companion on your pc ok and then connect your z3 Off, the pc companion detect the phone and what you have to do is go to the section where it says Support Zone and followed where it says software update of the phone will appear a window that says that the phone could not be found but more abajito says repair phone You click there and start the process ok, look for more reference and accuracy look for a video of it on youtube, I would leave the link but I block it I'll leave you the name of the video and try to find it out, luck. :good::good::good:
Flashear o Revivir Xperia ion con Sony PC companion ----- Search on youtube

Accidental wrong flash with Flashtool

Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.

Macs1209 said:
Looks like I killed my Z5. The model is 6683 (Z5 dual), and I flashed with E6533 (Z3+ dual).
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device", in detail VID_0000&PID_0000.
But if I disconnect the battery, it recognized as "SOMC Flash device", VID_0FCE&PID_DDDE
Is it possible to resurrect it?
I hope if I can flash with correct bootloader in this state, it will enought to boot up and able to flash with the right firmware.
Click to expand...
Click to collapse
Are you able to connect it in flashmode and fastboot ?

With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)

Macs1209 said:
With battery, no.
Without battery, my laptop recognize as "SOMC Flash device", but no tool can connect to it (like FlashTool).
(I think then different PID is the reason)
Click to expand...
Click to collapse
it seems to me that you are an advanced person in playing with your mobile, this kind of issues is beyond of my knowledge but I was replying to your thread hopefully someone here can help, I'm fearing that you have messed up with your mobile

Well, you could try to flash it from Ubuntu (NOT inside Windows 10 !) via FlashTool,
under windows there are limitations with different device IDs that separate drivers would be needed (and if only "wrong" ID is detected under Linux it doesn't really matter, since it's detected anyway),
perhaps under Linux operating systems you have more luck

Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.

Macs1209 said:
Thank you for idea, but not working.
Finally I found an old SETool3 box , and successfully flashed with it without battery
Somehow it can fixed it.
Click to expand...
Click to collapse
I am facing a similar situation, can you help me by telling me what exactly did you do to solve the issue step by step?

Same Problem With Me PLZ HELP
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..

[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please

Flashtool Doesn't Recognise This Device. U can use Setool/ Setool Fusion Box to Repai
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
Bro
In this Condition Flashtool Not Recognised Ur Device. There is only a best solution U Can Use SETOOL/SETOOL FUSION BOX To Repair/ Flash Ur Device.

[email protected] said:
Dear Bro Ive same problem with my Xperia e6683 Total Dead After Wrong Flash with Xperia Z3+ File... SO Plz help me how to fit step by step guide plz....
As on 20 Jan 2017
I've Flash Successfully It With Setool fusion Box Without Battery Use Test Pin Method. Now My My Phone Again Alive..
Click to expand...
Click to collapse
bma1973 said:
Dear Bro Ive same problem with my Xperia x Total Dead After Wrong Flash
The phone is completely dead, cannot turn on, not vibrating on power button etc.
When I connect to my laptop, it says "unable to recognize USB device"
using test pin method it is recognized as "SOMC Flash device"
i have backup ta partition and ftf firmware of my xperia i can't find any tool to flash
can you guide me please
Click to expand...
Click to collapse
wrong flash means wrong kernel!
you might be stuck on black screen when you frist switchon device! the device is running! but since its stuck on bootloops no interface is open!
press power and volume up button for 15+ seconds and let it JERK 3 times , this if force shutdown. the device should get connected now in flashmode