I was running the NKD Odexed ROM, and out of nowhere my phone just froze up and eventually went to Upload Mode where I was able to see that my Modem Crashed. When I pulled the batter and restarted my phone, I had no mobile service, and my Baseband and Software information both say Unknown. I cannot reboot into recovery, it just keeps bootlooping . I was able to flash the NK4 full restore, but when that loads up, even though it shows the LTE icon, my mobile data network status is set to disconnected. I also cannot boot to recovery from NK4 or any 4.4 bootloader to restore a backup. Any help would be incredibly appreciated. I'll be more than happy to buy some beers for anybody who can help me with this. Sprint is unable to help me on their end.
Edit: I should also note that I've tried Odin'ing the NKD modem several times when I am on android L, and the NK4 when on 4.4, neither do a thing to help.
jsmcmahon89 said:
I was running the NKD Odexed ROM, and out of nowhere my phone just froze up and eventually went to Upload Mode where I was able to see that my Modem Crashed. When I pulled the batter and restarted my phone, I had no mobile service, and my Baseband and Software information both say Unknown. I cannot reboot into recovery, it just keeps bootlooping . I was able to flash the NK4 full restore, but when that loads up, even though it shows the LTE icon, my mobile data network status is set to disconnected. I also cannot boot to recovery from NK4 or any 4.4 bootloader to restore a backup. Any help would be incredibly appreciated. I'll be more than happy to buy some beers for anybody who can help me with this. Sprint is unable to help me on their end.
Edit: I should also note that I've tried Odin'ing the NKD modem several times when I am on android L, and the NK4 when on 4.4, neither do a thing to help.
Click to expand...
Click to collapse
I had almost the same problem yesterday and was able to restore my backup this morning.
Here's the steps I took:
1. Using Odin 3.10.0
2. Make sure your phone is completely off (battery pull if necessary).
3. Go into Download Mode (Volume Down, Home, Power), then Volume UP
4. Plug phone via USB to computer, run Odin. Make sure you have a blue ID:COM light in Odin.
5. Uncheck Auto-Reboot.
6. Odin either NE5 firmware or NK4 firmware (depending on what your nanoid was).
7. Wait till Odin gives you a PASS, unplug USB and immediately go into Recovery (Volume UP, Home, Power).
8. Restore your nanoid and reboot.
This is assuming you have an extSD card and your nanoid is on it. If you don't you'll need to get one. If you don't have a nanoid, copy the rom you want to flash onto extSD and replace step 8.
Edit: FYI, the firmware files include the modem and TWRP recovery.
Edit: My reading skills are a little slow today, if you prefer the firmware with Philz, here's NE5 and NK4 firmware with Philz.
Ramer said:
I had almost the same problem yesterday and was able to restore my backup this morning.
Here's the steps I took:
1. Using Odin 3.10.0
2. Make sure your phone is completely off (battery pull if necessary).
3. Go into Download Mode (Volume Down, Home, Power), then Volume UP
4. Plug phone via USB to computer, run Odin. Make sure you have a blue ID:COM light in Odin.
5. Uncheck Auto-Reboot.
6. Odin either NE5 firmware or NK4 firmware (depending on what your nanoid was).
7. Wait till Odin gives you a PASS, unplug USB and immediately go into Recovery (Volume UP, Home, Power).
8. Restore your nanoid and reboot.
This is assuming you have an extSD card and your nanoid is on it. If you don't you'll need to get one. If you don't have a nanoid, copy the rom you want to flash onto extSD and replace step 8.
Edit: FYI, the firmware files include the modem and TWRP recovery.
Click to expand...
Click to collapse
Unfortunately, I can't count how many times I've tried this, both the firmware with TWRP, and firmware with Philz, my recovery will not boot. I get RECOVERY BOOTING.... in blue, RECOVERY IS NOT SEANDROID ENFORCING in red and Set Warranty Bit : recovery in yellow. This lasts about 30 seconds, and then it reboots to the same thing. The only way to get out of the recovery bootloop is to flash a firmware and not try to boot into recovery after, but then stuck with my modemless problem .
I can't even just go back Stock everything because I won't have service, my phone is basically a paperweight at this time.
jsmcmahon89 said:
Unfortunately, I can't count how many times I've tried this, both the firmware with TWRP, and firmware with Philz, my recovery will not boot. I get RECOVERY BOOTING.... in blue, RECOVERY IS NOT SEANDROID ENFORCING in red and Set Warranty Bit : recovery in yellow. This lasts about 30 seconds, and then it reboots to the same thing. The only way to get out of the recovery bootloop is to flash a firmware and not try to boot into recovery after, but then stuck with my modemless problem .
I can't even just go back Stock everything because I won't have service, my phone is basically a paperweight at this time.
Click to expand...
Click to collapse
Have you tried to odin the .tar version of Philz?
---------- Post added at 04:14 PM ---------- Previous post was at 04:05 PM ----------
As a last resort type thing, this is a one-click file from @rwilco12 to bring you back to stock unrooted NE5.
Ramer said:
Have you tried to odin the .tar version of Philz?
---------- Post added at 04:14 PM ---------- Previous post was at 04:05 PM ----------
As a last resort type thing, this is a one-click file from @rwilco12 to bring you back to stock unrooted NE5.
Click to expand...
Click to collapse
Yes, a previous version of Philz I can try this newer one though. I've also tried just TWRP. It's looking more and more like the weirdest brick I've ever heard of :-\.
Ramer said:
Have you tried to odin the .tar version of Philz?
---------- Post added at 04:14 PM ---------- Previous post was at 04:05 PM ----------
As a last resort type thing, this is a one-click file from @rwilco12 to bring you back to stock unrooted NE5.
Click to expand...
Click to collapse
Thanks for your attempted help , I actually ran both a NI3 and NE5 restore today . It would be safe to say I am not a noob at this stuff, I think I just got me a lemon :-\. I've been doing this for way too long now, I just don't get it.
jsmcmahon89 said:
Thanks for your attempted help , I actually ran both a NI3 and NE5 restore today . It would be safe to say I am not a noob at this stuff, I think I just got me a lemon :-\. I've been doing this for way too long now, I just don't get it.
Click to expand...
Click to collapse
It just seems to me that if you can get into Download Mode, it should be solvable. @tdunham, do you have anything to add that I didn't cover?
Try to do a phone reset with ##786# from the dialer. It's possible the phone cant authenticate with the network and that is why you're not getting signal.
I think this wipes internal storage but its worth a try to begin.
Next...
Pull the SD and the Sprint sim card.
Odin custom recovery and wipe absolutely everything including internal storage.
Power off the phone again, either from the recovery menu or battery pull.
Reinsert the sim card only, no SDcard, and do FULL factory Odin tar install, not the mini-bootloaders.
Let the rom boot fully but skip logging into Google and anything else and go straight into settings/backup and reset/factory reset.
Reboot again and see how it goes.
As a last resort you can try to re-pit (repartition) the phone but lets see how it goes from here.
tdunham said:
Try to do a phone reset with ##786# from the dialer. It's possible the phone cant authenticate with the network and that is why you're not getting signal.
I think this wipes internal storage but its worth a try to begin.
Next...
Pull the SD and the Sprint sim card.
Odin custom recovery and wipe absolutely everything including internal storage.
Power off the phone again, either from the recovery menu or battery pull.
Reinsert the sim card only, no SDcard, and do FULL factory Odin tar install, not the mini-bootloaders.
Let the rom boot fully but skip logging into Google and anything else and go straight into settings/backup and reset/factory reset.
Reboot again and see how it goes.
As a last resort you can try to re-pit (repartition) the phone but lets see how it goes from here.
Click to expand...
Click to collapse
I pulled the SD and Sim Card, and odin'd a custom recovery, but I cannot reach a custom recovery, just goes through the RECOVERY BOOTING.... boot loop explained in the OP. From there I've already done everything else close to 50 times now it just doesn't work.
When you go into settings/backup and restore/factory reset it's supposed to do something on it's own, mine just goes to recovery (ONLY IF STOCK RECOVERY IS INSTALLED OTHERWISE IT RECOVERY BOOTLOOPS) and the android guy falls over. It does not do the reset, I have to manually do it from stock recovery, but it doesn't seem to be helping.
Also, ##786# doesn't do anything. Neither does ##72786# as the Sprint rep was suggesting. My dialer (for one is lagging to all hell along with my keyboard) does not react, it just continues to show that #. This is on 100% stock too.
jsmcmahon89 said:
I pulled the SD and Sim Card, and odin'd a custom recovery, but I cannot reach a custom recovery, just goes through the RECOVERY BOOTING.... boot loop explained in the OP. From there I've already done everything else close to 50 times now it just doesn't work.
When you go into settings/backup and restore/factory reset it's supposed to do something on it's own, mine just goes to recovery (ONLY IF STOCK RECOVERY IS INSTALLED OTHERWISE IT RECOVERY BOOTLOOPS) and the android guy falls over. It does not do the reset, I have to manually do it from stock recovery, but it doesn't seem to be helping.
Also, ##786# doesn't do anything. Neither does ##72786# as the Sprint rep was suggesting. My dialer (for one is lagging to all hell along with my keyboard) does not react, it just continues to show that #. This is on 100% stock too.
Click to expand...
Click to collapse
It sounds like you corrupted your efs but I cant say for sure because I haven't seen it happen too often. You can always try to flash pit through odin and repartition. I'll attach the pit file in a zip so you can try it.
It seems like I would be more likely to have luck on Android L because at least when I flash that I have a phone that somewhat functions, I am missing a modem, and can not get one to stick at all, but I can at least connect to wifi, log into gmail accounts and do anything else. Where as on a stock 4.4 refresh I have a sick lag, it shows I have a modem but I am not provisioned for data, and sprint support is no help. They want me to bring my phone to a tech which is not something I am looking to do knowing I tripped the KNOX flag.
tdunham said:
It sounds like you corrupted your efs but I cant say for sure because I haven't seen it happen too often. You can always try to flash pit through odin and repartition. I'll attach the pit file in a zip so you can try it.
Click to expand...
Click to collapse
I odin'd that pit and tried to start fresh, no luck. I can't thank you guys enough for your continued effort
Edit: I am reading this post http://forum.xda-developers.com/showthread.php?t=2610757
I have never used the Nand Erase All or Phone EFS Clear options in Odin, but this seems like it might help?
2nd Edit: After flashing the PIT file with NE5 stock rom I achieved data. Now I have an incredibly laggy stock rom, which might just have to do for now, because I still can't get to a custom recovery.
I did not use Nand Erase All or Phone EFS Clear, but am still very interested.
Realized a new issue today. My phone will only charge when off. Still open to suggestions.
Im haveing the exact same issue you are and no clue what to do about it.
Wow I must be lucky all I did was a battery pull and my phone worked again (back when I was on moar 5.0) (i haven't encountered it on moar 6.1)
Sent from my SM-G900P
gtuansdiamm said:
Wow I must be lucky all I did was a battery pull and my phone worked again (back when I was on moar 5.0) (i haven't encountered it on moar 6.1)
Sent from my SM-G900P
Click to expand...
Click to collapse
I don't think you are haveing the same issues we are.
I had similar happen to me and the only thing that fixed it was to go back to the first stock, ND2 I think and work my way back up. It happened to me on NKD also, not sure if it was the same exact thing but sounds close. IIRC after flashing back to the first stock ROM thing started working but prior to that I Odin flashed every package that came with a pit file.
miked63017 said:
I had similar happen to me and the only thing that fixed it was to go back to the first stock, ND2 I think and work my way back up. It happened to me on NKD also, not sure if it was the same exact thing but sounds close. IIRC after flashing back to the first stock ROM thing started working but prior to that I Odin flashed every package that came with a pit file.
Click to expand...
Click to collapse
i was on nkd last i could remember but as far as know you cant downgrade the bootloader.
jackrabbit72380 said:
I don't think you are haveing the same issues we are.
Click to expand...
Click to collapse
well back when i had the issue id randomly take out my phone from my pocket and see it stuck on a screen that said upload mode modem crashed
lets hope that there isnt a second issue out there as well
back then it was a 50/50 shot doing a battery pull and getting the phone to boot
sometimes even while i had charge i would have to plug phone into a power supply and then try turning it on
but regardless i wish you guys best of luck
jackrabbit72380 said:
i was on nkd last i could remember but as far as know you cant downgrade the bootloader.
Click to expand...
Click to collapse
Downgrade on the sprint s5 is possible with Odin, no negative side effects. FWIW theres a few threads around too that back this statement.
Related
Hope someone has some info.
I have recently tried to recover my phone via Odin flash. I'm flashing the GummyCharged 1.9 FE odin file. I've done this SEVERAL times w/ out any problems.
My problem now is that when the Odin flash is complete it shows "Pass" and when I reboot my phone it boots with an old version of CWM (4.0.0.1). Not only that but when I try to "reboot phone" it boot loops back to CWM and will not load ANY for of an OS. I've tried multiple Odin files with no luck. Same thing over and over.
Anyone have any suggestions? I'm used to having to recover my phone from a bricked state... but never had an issue where I push a file to the phone and it will not boot after. Tried wiping data/cache after Odin as well... Still nothing.
I would try going back to stock using Imnuts' stock ROM and PIT file which can be found here: http://forum.xda-developers.com/showthread.php?t=1111486
That has always fixed any and all issues I've been having with the phone after messing something up.
EDIT: Here is the stock EE4 ROM http://forum.xda-developers.com/showthread.php?t=1172182
hazard209 said:
I would try going back to stock using Imnuts' stock ROM and PIT file which can be found here: http://forum.xda-developers.com/showthread.php?t=1111486
That has always fixed any and all issues I've been having with the phone after messing something up.
EDIT: Here is the stock EE4 ROM http://forum.xda-developers.com/showthread.php?t=1172182
Click to expand...
Click to collapse
Hey man, I cant thank you ENOUGH!!!! After A LOT of trial and error (had to download the ee4 file from another link) I was able to get this beast to boot back up. I REALLY appreciate your quick response and help!
KaneD20 said:
Hey man, I cant thank you ENOUGH!!!! After A LOT of trial and error (had to download the ee4 file from another link) I was able to get this beast to boot back up. I REALLY appreciate your quick response and help!
Click to expand...
Click to collapse
No problem. Glad you got her back up and running. No one likes a $500 paperweight.
Props to hazard he's always helping people... just want to let you know
Your a good dude...
SENT FROM THE DOG POUND
hazard209 said:
No problem. Glad you got her back up and running. No one likes a $500 paperweight.
Click to expand...
Click to collapse
Yeah, no doubt. And I was able to do a restore on the Imnuts PBJ OBT kernel from 7/30... my problem started when I installed the new kernel version (from 8/8) and tried to backup/restore. Working perfectly now though!
Having same issue still getting recovery mode
I did a fix sd cardupdate for the rom clocking.
I had gumicharge rom on it
After 4 hours my battery was at 50% so I decided hey i can just load the rom on it again and no problem clean free.
It did not work. I am using odin.
It did not work so I got the pit file from this and it gave my system life and the ed1 file wont download it stalls out and failes i tried using
CI510_VZW_EE4_ALL_ONE-LTE-CP_REV03_user_CL1014954.tar.md5
or
CI510_VZW_EP1F_ALL_ONE-LTE-CP_REV3_user_CL300919_Rooted_Debloated.tar.md5
both do nothing.
My phone just sits there reboots into Manual mode and looks like my blue recovery console.
Clear cache
Upload from SD Card
and clear memory so forth.
Thats all my options.
I am now stuck with phone i cant use or update. I am at work so now i cant use the megaupload since those are blocked by our firewall.
I was able to remote to pc to get a pit file.
At this point i dont know what to do or just do insurance claim on my phone and get another one. I dont know how to fix it now.
I cant read the sd card on any computer to put stuff on it and odin is writing things to it The pit file on this fix did give me a recovery enviroment but nothing on roms are on the sd card.
roms ive tried dont load for automaticaly its just in that manual mode thing with the icon of the little android dude.
it says
Android system recover (3e)
Enter: OK key, select:Vol Up/Vol Down
Reboot system now
apply update from sdcard
wipe data/factory reset
wipe cache partition
bewlo it syas #manual mode* and little android guy with eclamation point next to him.
I have tried severla tiems 3 different roms
2Much2Ask4 said:
I did a fix sd cardupdate for the rom clocking.
I had gumicharge rom on it
After 4 hours my battery was at 50% so I decided hey i can just load the rom on it again and no problem clean free.
It did not work. I am using odin.
It did not work so I got the pit file from this and it gave my system life and the ed1 file wont download it stalls out and failes i tried using
CI510_VZW_EE4_ALL_ONE-LTE-CP_REV03_user_CL1014954.tar.md5
or
CI510_VZW_EP1F_ALL_ONE-LTE-CP_REV3_user_CL300919_Rooted_Debloated.tar.md5
both do nothing.
My phone just sits there reboots into Manual mode and looks like my blue recovery console.
Clear cache
Upload from SD Card
and clear memory so forth.
Thats all my options.
I am now stuck with phone i cant use or update. I am at work so now i cant use the megaupload since those are blocked by our firewall.
I was able to remote to pc to get a pit file.
At this point i dont know what to do or just do insurance claim on my phone and get another one. I dont know how to fix it now.
I cant read the sd card on any computer to put stuff on it and odin is writing things to it The pit file on this fix did give me a recovery enviroment but nothing on roms are on the sd card.
roms ive tried dont load for automaticaly its just in that manual mode thing with the icon of the little android dude.
it says
Android system recover (3e)
Enter: OK key, select:Vol Up/Vol Down
Reboot system now
apply update from sdcard
wipe data/factory reset
wipe cache partition
bewlo it syas #manual mode* and little android guy with eclamation point next to him.
I have tried severla tiems 3 different roms
Click to expand...
Click to collapse
Not sure if you're going into download mode properly but try this:
open ODIN
add the PIT file in the PIT section
add the EE4 OEM file in the PDA section (do not use the phone section)
leave everything else in ODIN as default except click on "re-partition"
take your battery out of the phone
hold the volume down button & plug in your USB cable (do not let go of the volume down button until you are in download mode)
ODIN should now now show a yellow com port for your phone on top left of ODIN and your phone should display "download mode"
select start
When it's complete ODIN will show in green that it passed. Unplug your phone, put the battery back in & boot
Hope this helps & good luck
vudiff said:
Not sure if you're going into download mode properly but try this:
open ODIN
add the PIT file in the PIT section
add the EE4 OEM file in the PDA section (do not use the phone section)
leave everything else in ODIN as default except click on "re-partition"
take your battery out of the phone
hold the volume down button & plug in your USB cable (do not let go of the volume down button until you are in download mode)
ODIN should now now show a yellow com port for your phone on top left of ODIN and your phone should display "download mode"
select start
When it's complete ODIN will show in green that it passed. Unplug your phone, put the battery back in & boot
Hope this helps & good luck
Click to expand...
Click to collapse
I would do this but before starting the flash in odin put the battery back in and uncheck the auto reboot box, when its done unplug from pc and remove battery, put it back in then boot up phone
blazing through on my VZ Droid Charge 4G
anoninja118 said:
I would do this but before starting the flash in odin put the battery back in and uncheck the auto reboot box, when its done unplug from pc and remove battery, put it back in then boot up phone
blazing through on my VZ Droid Charge 4G
Click to expand...
Click to collapse
don't put the battery in during flash & leave auto reboot checked. Auto reboot will not do anything as there isn't a battery installed... it'll just turn off. Unplug the phone after you flash it & put battery back in & boot
vudiff said:
Not sure if you're going into download mode properly but try this:
open ODIN
add the PIT file in the PIT section
add the EE4 OEM file in the PDA section (do not use the phone section)
leave everything else in ODIN as default except click on "re-partition"
take your battery out of the phone
hold the volume down button & plug in your USB cable (do not let go of the volume down button until you are in download mode)
ODIN should now now show a yellow com port for your phone on top left of ODIN and your phone should display "download mode"
select start
When it's complete ODIN will show in green that it passed. Unplug your phone, put the battery back in & boot
Hope this helps & good luck
Click to expand...
Click to collapse
This is pretty much what fixed it for me. DON'T GIVE UP! Trust me, I literally had to try this several times before it booted up. I know its frustrating, trust me, but if you stick with it you can fix the phone.
Each time you're able to get to recovery mode, if you're phone doesn't boot, do like five data wipes and wipe cache. Then Odin the .pit and the EE4 from the link above in the pda field (both at the same time).
Good luck! Stick with it I know you CAN fix this!
Sent from my SCH-I510 using XDA Premium App
KaneD20 said:
This is pretty much what fixed it for me. DON'T GIVE UP! Trust me, I literally had to try this several times before it booted up. I know its frustrating, trust me, but if you stick with it you can fix the phone.
Each time you're able to get to recovery mode, if you're phone doesn't boot, do like five data wipes and wipe cache. Then Odin the .pit and the EE4 from the link above in the pda field (both at the same time).
Good luck! Stick with it I know you CAN fix this!
Sent from my SCH-I510 using XDA Premium App
Click to expand...
Click to collapse
No need to wipe anything... when you have "re-partition" checked it wipes everything but the sd card
vudiff said:
No need to wipe anything... when you have "re-partition" checked it wipes everything but the sd card
Click to expand...
Click to collapse
I'm sure you're right, these are just the things that I did when I finally got it working.
I got stuck myself last night and odin started to fail every attempt, even with the pit file and following numerous instructions found around the site. I actually thought my phone was bricked for good.
I installed PST lite and selected the PIT and EE4 and selected to repartition. It took longer to do but everything came back up. Then using odin I was able to flash back to the rom I had before.
This was after an hour of trying to fix it as I mentioned and Odin kept failing.
^attempting to reflash via samsung pst lite.
loaded PIT, stock EE4. checked "repartition". when I click download, it starts, but freezes at 9%. RX_TIMEOUT shows on the phone screen.
I'm trying this method b/c Odin is not working. Same thing, just hangs, sez RX_TIMEOUT. (repartition w/ PIT, stock EE4)
sushi_stalker said:
^attempting to reflash via samsung pst lite.
loaded PIT, stock EE4. checked "repartition". when I click download, it starts, but freezes at 9%. RX_TIMEOUT shows on the phone screen.
I'm trying this method b/c Odin is not working. Same thing, just hangs, sez RX_TIMEOUT. (repartition w/ PIT, stock EE4)
Click to expand...
Click to collapse
Have you tried putting the battery back in during the flash?
Sent from my Droid Charge running GummyFroyo 1.9.1
kvswim said:
Have you tried putting the battery back in during the flash?
Sent from my Droid Charge running GummyFroyo 1.9.1
Click to expand...
Click to collapse
Yes. tried both with and without. Just hangs. Can never fully make it through the flash.
Stuck with soft bricked phone.
Waiting for my wife to get home with her PC laptop. Hoping it really is just a platform issue (running ODIN on Mac Boot Camp)
sushi_stalker said:
Yes. tried both with and without. Just hangs. Can never fully make it through the flash.
Stuck with soft bricked phone.
Waiting for my wife to get home with her PC laptop. Hoping it really is just a platform issue (running ODIN on Mac Boot Camp)
Click to expand...
Click to collapse
What version of Odin are you using? I'm pretty sure I'm using Odin v. 1.82 or something close to that. Not too sure that it would make the difference. Just a thought.
Also, I had to Odin QUITE a few times to get it back up. I had even run the Odin w/ JUST the .pit file. Thought I read somewhere to run the .pit an UNCHECK the repartition box (I know it says it'll give you an error but I did not get one).
All in all, not too sure what exactly it was that finally got it working. But I eventually ran the .pit and ee4 (both posted in post #2 of this thread). Then when my phone booted up, it looked like the problem remained. I had to get back to work from lunch so I just put the phone in my pocket. Then out of nowhere I heard the boot animation come on.
Just make sure you read through, pretty much, all of the threads that deal w/ this stuff. There is almost always someone that has come across the same problem that you may have and almost always someone who had figured out how to fix it.
Good luck, this CAN be fixed!
I just rooted my phone and I was trying to flash it to gingerbread and it was working fine, but clockwork mod wouldn't let me backup. A forum told me to dlete the recovery in the system and replace it and i did, but the replacement was titled "recovery - copy". i tried to reboot my phone but it is stuck at the "Galaxys S 4G - TMOBILE" screen. I can't get into recovery mode and i could never get into download mode. HELP!
How did you try to get into download mode and what rom did you flash?
Sent from my SGH-T959V using xda premium
here is a guide http://forum.xda-developers.com/showthread.php?t=1069032
pull battery and then plug in usb then hold down volume and then you should be in download mode. you should see phone on odin.
GMSonicX said:
I just rooted my phone and I was trying to flash it to gingerbread and it was working fine, but clockwork mod wouldn't let me backup. A forum told me to dlete the recovery in the system and replace it and i did, but the replacement was titled "recovery - copy". i tried to reboot my phone but it is stuck at the "Galaxys S 4G - TMOBILE" screen. I can't get into recovery mode and i could never get into download mode. HELP!
Click to expand...
Click to collapse
i have yet to see anyone say "delete" the recovery file. it is always "overwrite". regardless, put your phone into download mode. you are doing it wrong. try again until you get it right.
remove the battery. leave it off for 10 seconds. put it back in. press and hold the two volume buttons at the same time. then plug in the usb cable that is connected to your computer. odin should be running already. i would follow gb start pack from here.
i turned of the phone and held the volume down button and the power button, letting go of the power once the turn on screen came up. i was trying to flash the leaked android 2.3.5 for the galaxy s 4g
please read my previous post carefully. i never said to press the power button at all.
OKAY, dwld mode is volumes plus USB cable, never failed me, even when I failed a flash through odin/heimdall and just maybe a yellow pixel or even nothing shows up.
If it flashes it is dwld. The GS4g has absolutely no junk bootloader witthout proper download mode unlike other galaxies.
PS. Who else wants a Galaxy Nexus?
What is the tmobile warranty policy, I know if there is a problem with your phone even due to damage, the warranty covers it for replacement after paying contract price, but do they allow a change of phone eg instead of paying 99 or 139 for another gs4g, get a galaxy nexus for 199?
My phone works, but after it fell, it overheats and loses battery. I even got a free new battery, and I even went back to stock KD1 for a while, no difference.
So, I did what you said, and i got into download mode, no problem. but when i tried to flash with odin it just said fail.. any suggestions?
Although the square window might say "Fail" there's a status window in the bottom left-hand side of ODIN that should give you more information. What does that window say when you try to flash?
It said succesful 0/ failed 1. I tried to reboot my phone and now it won't turn on at all...
It sounds like your boot loaders are hosed.
Keep ODIN open & use the battery-pull method to see if it'll go into download mode (the screen might still be black, but see if ODIN recognizes it).
If it does:
Download chadster's KG4: http://forum.xda-developers.com/showthread.php?t=1183413
Put CODE_T959VUVKG4_CL138158_REV00_user_low_noship.tar.md5 in PDA
Put Hawk_Sidekick_VibrantPlus_831.pit in PIT
Put SGH-T959V-CSC-TMB-VIBRANT.tar.md5 in CSC
Put T959VUVKG4-Phone-CL1037720.tar.md5 in PHONE
Let ODIN decide what boxes need to be checked and flash. That will get you booted up on GB with the proper boot loaders.
Try the Unbrickable Mod in the dev section. Brought mine back today. I had a Bright WHITE screen. lol
NO BOOT
After flashing this kernel> sms-T959V-KJ6-antsvx.v1.1.3 my Galaxy S4G will not boot AFTER restoring my backup using CWM 5.0.2.8. My phone runs perfect with the stock rom and this kernel. ONLY after restoring does it NOT boot.
Can someone shine some light on this situation?
You need to restore using the kernel you made the back up from. You can then flash the new kernel over the restored back up.
lumin30 said:
You need to restore using the kernel you made the back up from. You can then flash the new kernel over the restored back up.
Click to expand...
Click to collapse
I can only get into download mode, what app would I use to flash the kernel ? (its saved on my pc)
---------- Post added at 05:06 PM ---------- Previous post was at 04:42 PM ----------
Thanks much Lumin30. Had to read your post sloooow and figure it out, and I got it. I flashed the stock+Voodoo-T959VKJ1 in Odin and it booted right up
then flashed the sms-T959V-KJ6-antsvx.v1.1.3 kernel in CWM. Im good to go now.
This has happened to me 2 other times can you suggest why? The other times I restored phone back to factory :crying:.
Still not booting AFTER restoring cwm backup
I always attempt to restore a backup that I have made using cwm as a test. Im trying to restore using the same kernel I made the backup with. When I proceed the full restore appears to go through (I get "restore complete" message in CWM v.5.0.2.8), but when I click on "reboot system now" my phone goes ONLY to the Samsung screen and stays there.
I have restored my phone to stock about 5 times carefully re-rooting and flashing the kernel with the stock firmware. Now, I have AntonX Barebones and Basic with a twist kernel installed, they work perfectly! But I CANNOT boot AFTER restoring a full backup, unless I use Odin. Can someone help me to address and fix the cause?
Edit> I was able to restore and boot up automatically a backup using CWM 5.0.2.8 of AntonX's Barebones Rom with bhundven's Blastoff 2.5 kernel. Dont know why it restored and booted properly this time but this is what I did:
I made a fresh backup of Barebones with Blastoff because I wanted to try Valhalla Black (nice ROM). I flashed it first using the "generic" install and checked through its features then wanted to see how the "custom" install felt. I decided I liked Barebones better and flashed the Blastoff kernel onto Valhalla Black, Then booted into CWM and restored my Barebones with Blastoff backup. Without wiping anything or fixing permissions my backup was fully restored and my phone booted properly on its own. I know this is what should happen, but it wasnt for me. And every time I attempted this I was restoring using the same kernel that the backup was made with. I restored twice since just to test it and both times my phone booted on its own. I believe my problemo is solved. It is possible I had a couple of bad downloads on my part with AntonX Basic with a twist 1.1.3
Thanks to the community (XDA)
My VZW rooted 4.4.4 GS5 decided to shut off, and reboot into recovery. Had TWRP with SS installed about 3 weeks ago, and all was working EXCELLENT, without any problems. I've been using this thing rooted and debloated for about 2 or more years. I have never tried to install any other custom ROMs. All I did was debloat the VZW crap off of it. I tried SS in the past, but it did not seem to do anything, so I uninstalled it, so I thought.
It appears as though through recovery, that it has been wiped.
The ROM installed was the 4.4.4, which all I wanted to do was debloat a couple years ago, which I did. Now the phone seems to have taken a crap, and I can't seem to get it to do anything. There is probably about 70% battery to play with. I can get it booted to recovery, but nothing else. I attempted to sideload the 4.4.4 firmware, but was unsuccessful. Maybe I don't know what I am doing. When I originally rooted, I used Odin to downgrade to 4.4.4, per instructions I found. But now, I don't know what to do.
Can someone please hold my hand here, and PM or email me so I can get this phone up and running again? This is both my personal and business phone. Please PM me, or email to [email protected]
Thank you.
Can you get into Download mode? If so, from there you should be able to Odin flash firmware located at sammobile's site.
Beeko said:
Can you get into Download mode? If so, from there you should be able to Odin flash firmware located at sammobile's site.
Click to expand...
Click to collapse
It will boot to Recovery mode, and give me the options to install via ADB, from external, etc. Not sure if I know exactly what you are meaning by d/l mode.
It obviously does not boot normally.
When it boots to recovery, my options are reboot system, apply update from 1. ADB, 2. External, 3. Cache, or the two wipe options.
That is as far as it will go now.
Just put batt back in, connected USB cord from PC and tried to boot. Up top, in red Secure Fail: Recovery. Then a msg on the screen. System software not authorized by VZW has been found on your phone. Please turn off and go to a VZW store for help.
When it does turn on, it goes to the Samsung screen and says Custom, with the unlocked padlock. It has displayed that since the day I rooted, back about two years ago, but has always booted through.
Now it is going back to Recovery, and gives me those 5 previous options for installing / recovery. But that's where I am stuck, and need a little (a lot) of expertise and guidance.
Pull battery, put battery back in , then hold power, volume down and home at same time. If it boots to download mode then use Odin
johnnycooper said:
Pull battery, put battery back in , then hold power, volume down and home at same time. If it boots to download mode then use Odin
Click to expand...
Click to collapse
I don't think it boots to d/l mode. It boots to Recovery, then gives me the options that I previously listed; ABD, External, or cache. I don't believe that ADB is d/l mode, is it?
johnnycooper said:
Pull battery, put battery back in , then hold power, volume down and home at same time. If it boots to download mode then use Odin
Click to expand...
Click to collapse
It only boots to recovery.
You tried to boot to download mode with battery pulled - volume down, power, home button?
johnnycooper said:
Pull battery, put battery back in , then hold power, volume down and home at same time. If it boots to download mode then use Odin
Click to expand...
Click to collapse
johnnycooper said:
You tried to boot to download mode with battery pulled - volume down, power, home button?
Click to expand...
Click to collapse
Okay, now it seems like I 'might' be getting somewhere. Yes, now the battery is OUT, and it did boot to ODIN, and I think it might be doing something. See?, need the hand holding. Will update, in a bit to see if this works. Thank you!
The phone says it's d/l, but there doesn't seem to be much happening on the ODIN screen.
You have to have usb hooked to pc , open Odin on pc. Then press up on phone then load factory tar to Odin
---------- Post added at 10:36 PM ---------- Previous post was at 10:33 PM ----------
Go here and read the part that days prepare your phone after #9
http://forum.xda-developers.com/showthread.php?t=3290370
Working Root Method For 5.0 Lollipop Roms [OE1] [OG5] [OK3] [PB1] [3-3-16]
Okay, it went through what appeared to be an install, then it showed that it was upgrading, through 145, did a reboot, but now all it is doing is turning on and off, showing the GS5 screen with the Custom padlock logo.
Pull battery , boot to recovery, wipe cache. If that dont work, start over
boblpn said:
Okay, it went through what appeared to be an install, then it showed that it was upgrading, through 145, did a reboot, but now all it is doing is turning on and off, showing the GS5 screen with the Custom padlock logo.
Click to expand...
Click to collapse
It prepared the phone, rebooted, showed the red VZW screen, and now seems to be stuck in a boot loop. I have done a battery pull, and rebooted, but still stuck in a loop.
Should I try installing a different ROM? If yes, which one? Can you provide a link?
boblpn said:
Should I try installing a different ROM? If yes, which one? Can you provide a link?
Click to expand...
Click to collapse
Already did, it's in the link
question..What if he ONLY wants to go back to his KK 4.4...all he has to do is ODIN the NCG, towelroot, install SuperSU and then flash the 4.4 and he'll be back...what is being offered may not be what he wants and then may not go back to KK if he so desires...you got to give and explain to users what will happen if done...
If you can get to DL mode, Run Odin as admin on your PC and then load up whatever stock firmware you want from HERE.
He can use this thread here which could be helpful as well. http://forum.xda-developers.com/showthread.php?p=53447942#post53447942
boblpn said:
The phone says it's d/l, but there doesn't seem to be much happening on the ODIN screen.
Click to expand...
Click to collapse
It won't download anything unless you push it using Odin. Boot into recovery and give me the build number at the top. Then we can find the factory firmware to push with Odin in download mode.
Hey guys,
decided to flash the latest DBT Firmware via Odin to get back to stock completely. (G930FXXU3ESA3)
After flashing the firmware through Odin the phone reboots and then installs an update and erases data (blue background).
After a second reboot I end up with a blue screen and the simple error: "No command".
I can not get into recovery, as I end up with the same error message wether booting into recovery or the system.
I CAN however get into downloadmode and flash twrp, after that I can boot into system but I want to keep the whole system vanilla, without TWRP.
Installing TWRP keeps the device encrypted, no matter what. I can wipe, then install no-verity-encrypt and as soon as I reboot the device is encrypted again.
Ive tried: Different Firmware Version (December 2018), 3 different cables, different odin versions.
Edit: attached an Image of the message that Pops up after about 30sec on the no command screen.
Ok, so your device will take UK Unbranded BTU firmware. You can get it from a few sources and even direct from Samsung servers with Samtool.
Forget all that flashing TWRP and non verify nonsense, if you can get into download mode you can flash firmware, obviously make sure the firmware downloaded is not corrupt etc.
I've used Odin V10 -13 to flash BTU and every version flashed it correctly. Sometimes you do get that "installing update" and then "erasing" but that's fine just leave the phone for a few minutes it should eventually reboot normally.
FLASH No verity.zip
VIA TWRP
https://forum.xda-developers.com/attachment.php?attachmentid=4490455&d=1525176288
cooltt said:
Ok, so your device will take UK Unbranded BTU firmware. You can get it from a few sources and even direct from Samsung servers with Samtool.
Forget all that flashing TWRP and non verify nonsense, if you can get into download mode you can flash firmware, obviously make sure the firmware downloaded is not corrupt etc.
I've used Odin V10 -13 to flash BTU and every version flashed it correctly. Sometimes you do get that "installing update" and then "erasing" but that's fine just leave the phone for a few minutes it should eventually reboot normally.
Click to expand...
Click to collapse
Just tried the latest BTU with Odin 3.13.1, same problem. Its reboots into the blue screen, applying system update to about 32% and then switches to "Erasing". After about 1min it reboots, shows "Installing System update" for a second and I end up with "No command" again. And from there on it just constantly reboots into the "No command" screen.
This seems like the same problem. I can not enter stock recovery to wipe though...
Things ive tried so far:
- Different firmware Versions (all oreo since downgrading is impossible)
- Formating with pit files
- Different Odin Versions
- Unplugging and replugging the battery
- Installing TWRP, wiping data and then installing stock recovery through TWRP
Did u try in Odin nand erase and repatition option? If not try it ( make sure u have pit file extracted or downloaded from the net)
Scorpionea said:
Did u try in Odin nand erase and repatition option? If not try it ( make sure u have pit file extracted or downloaded from the net)
Click to expand...
Click to collapse
Did a efs backup through TWRP just in case, then flashed the latest DBT firmware with nand erase -> still the same problem.
I can only guess that this was caused by using a backup from another phone back when Oreo came out, this probably messed something up really badly. Very weird, im kinda lost.
Killuminati91 said:
Just tried the latest BTU with Odin 3.13.1, same problem. Its reboots into the blue screen, applying system update to about 32% and then switches to "Erasing". After about 1min it reboots, shows "Installing System update" for a second and I end up with "No command" again. And from there on it just constantly reboots into the "No command" screen.
This seems like the same problem. I can not enter stock recovery to wipe though...
Things ive tried so far:
- Different firmware Versions (all oreo since downgrading is impossible)
- Formating with pit files
- Different Odin Versions
- Unplugging and replugging the battery
- Installing TWRP, wiping data and then installing stock recovery through TWRP
Click to expand...
Click to collapse
Ok, from the no command screen do the following.
Hold power until phone switches off, then press power+home+volume up. The phone should now boot into original recovery screen. Select "wipe/factory reset" and then reboot device. Job done.
cooltt said:
Ok, from the no command screen do the following.
Hold power until phone switches off, then press power+home+volume up. The phone should now boot into original recovery screen. Select "wipe/factory reset" and then reboot device. Job done.
Click to expand...
Click to collapse
Tried that, recovery is simply not working. If I hold vol - + power + home to restart and switch immediatly to vol + I boot into the usual blue screen with No command. I even tried unplugging the battery to shut off the phone and boot into recovery from there but that is not working either. Sorry should have stated that more clearly.
If I flash TWRP however, I can easily boot into TWRP with the recovery button combo.
Killuminati91 said:
Tried that, recovery is simply not working. If I hold vol - + power + home to restart and switch immediatly to vol + I boot into the usual blue screen with No command. I even tried unplugging the battery to shut off the phone and boot into recovery from there but that is not working either. Sorry should have stated that more clearly.
If I flash TWRP however, I can easily boot into TWRP with the recovery button combo.
Click to expand...
Click to collapse
Ok it's a tricky one so one more thing I would suggest is download and install Samsung smart switch on your PC, place the phone in download mode plug it into lap top and choose emergency software recovery in smart switch
Edit. I just remembered before that try this button combo from the no command screen volume up+volume down+power.
cooltt said:
Ok it's a tricky one so one more thing I would suggest is download and install Samsung smart switch on your PC, place the phone in download mode plug it into lap top and choose emergency software recovery in smart switch
Edit. I just remembered before that try this button combo from the no command screen volume up+volume down+power.
Click to expand...
Click to collapse
Hmmh. Searched a lot for the version that still supported emergency recovery. (which seems to be 4.0). If I go into download mode, start smartswitch and try to use emergency recovery there is nothing for me to select.
Volume up + down and power gives me the terminal like look which I attached in the first post with all those error messages.
Killuminati91 said:
Hmmh. Searched a lot for the version that still supported emergency recovery. (which seems to be 4.0). If I go into download mode, start smartswitch and try to use emergency recovery there is nothing for me to select.
Volume up + down and power gives me the terminal like look which I attached in the first post with all those error messages.
Click to expand...
Click to collapse
The EFS partition is corrupt or blank, it's the only logical explanation but the TWRP back up should solve that, without looking at it my self and running some commands i cant help your further.
cooltt said:
The EFS partition is corrupt or blank, it's the only logical explanation but the TWRP back up should solve that, without looking at it my self and running some commands i cant help your further.
Click to expand...
Click to collapse
TWRP backup was created after I ran into problems though. Ive checked some more things and it seems like the serial number that is displayed (in combination rom and or Z3X) is not the same SN that is printed on the back of the phone. Could this be related? And how would I go about changing it back to the one on the sticker? The IMEI is correct.
Had someone who was more into the whole thing contact me here but when I wanted to "donate" only half of what he was asking he refused to help me.
Killuminati91 said:
TWRP backup was created after I ran into problems though. Ive checked some more things and it seems like the serial number that is displayed (in combination rom and or Z3X) is not the same SN that is printed on the back of the phone. Could this be related? And how would I go about changing it back to the one on the sticker? The IMEI is correct.
Had someone who was more into the whole thing contact me here but when I wanted to "donate" only half of what he was asking he refused to help me.
Click to expand...
Click to collapse
Thats because he's a scammer. Never donate to get your phone fixed! Donate to Rom developers and things you like but never to get the phone fixed, they're usually lying.
The serial number should be the same ON the phone as displayed IN phone. Tell me the story about the phone, how did you get it? what region? where are you? what firmware was installed? Can you still flash a ROM with TWRP? Can you check OEM unlock?
---------- Post added at 04:53 PM ---------- Previous post was at 04:51 PM ----------
nmnmnmnmnmnmnmnmnm
Pretty sure he was just trying to remote repair for a price, which is not allowed on XDA. Would obviously donated on my own if he actually fixed it.
Bought the phone unlocked directly from a provider (simply - germany - dbt - g930f) back in 2016. Tripped kn0x after a few months, installed a few custom roms until Oreo came out.
This is where I messed up I think: I used a TWRP backup from someone else that he had shared here on XDA, which probably included his /efs too.
Since then I had constant connection problems, weak internet connection, dropped calls and so on.
Broke my screen and then decided to repair it myself. Bought a new frame, screen, battery, usb-port, earpiece and vibrator - managed to assemble all of that.
I can install all latest official firmwares (bootloader 3) through Odin. If I leave it at that I have no recovery and end up with the initially shown screen and "No command".
If i install TWRP from there and simply root with magisk or apply dm-verity-fix I can boot into the stock firmware with everything working.
I can also install ROMs. Just going completely vanilla is not possible anymore. OEM Unlock is checked, USB debugging works.
Edit: What is also astounding: If I flash version DBT-G930FXXS3ERHD-20180918145033 (oldest possible Oreo Version) I can enter recovery and do a factory reset and wipe cache.
If I do that however I am stuck at the Galaxy S7 Logo, not even bootlooping.
Killuminati91 said:
This is where I messed up I think: I used a TWRP backup from someone else that he had shared here on XDA, which probably included his /efs too.
Click to expand...
Click to collapse
awww.....come on man you should have said this at the start! Of course you can't use someone else's EFS data, it's unique to your handset. Custom Rom's patch some but not all EFS data that's why they work and in your case that's why Stock firmware isn't going too.
Anyway if this is the problem (and i suspect it is) there is only one way to fix it with Octopus box which can write all the important info back onto the EFS. Your IMEI, Serial, Mac address etc. Odin reads the info from the EFS prior to nand write start, if the phone serials don't match it will always fail at some point.
You can install a custom via twrp but it will not work correctly due to EFS data miss match. Octopus box is your answer.
cooltt said:
awww.....come on man you should have said this at the start! Of course you can't use someone else's EFS data, it's unique to your handset. Custom Rom's patch some but not all EFS data that's why they work and in your case that's why Stock firmware isn't going too.
Anyway if this is the problem (and i suspect it is) there is only one way to fix it with Octopus box which can write all the important info back onto the EFS. Your IMEI, Serial, Mac address etc. Odin reads the info from the EFS prior to nand write start, if the phone serials don't match it will always fail at some point.
You can install a custom via twrp but it will not work correctly due to EFS data miss match. Octopus box is your answer.
Click to expand...
Click to collapse
Dang it. Thank you! Off to find someone who can do this via remote access or in Berlin.
Same situation right now with my S7. Damn.
Hi everyone. Did you guys find any way to resolve this issue? i have exactly the same issue here.. but in my case i cannot use twrp cuz i never installed it before... the issue happened right after i tried to enter the recovery mode by pressing the buttons...
my wife's galaxy s7 touch screen was acting weird and i tried to get into the recovey mode..which is pretty muh easy to do... but once i tried the no command msg came up and now i have exatly the same case as the guy that opened this thread....also done everything hes done....any clue about this anyone?
id appreciate some help..
thanks in advance
Diego Boffa
Anyone?
I have exactly the same error with "fail to open recovery_cause(No such file or directory)#
My Tablet is now stuck with a blue "android dead" screen saying "No command".
My history to disaster:
- i've recovered a "broken" Samsung Tablet (sm-T585) with corrupted file system via
* Download Mode works -> TWRP install -> Mount option -> use ADB to recreate EFS partition -> re-flash stock image (android 8) with odin
- device works fine
- then i've noticed it can only be used with a certain cell provider (o2)
- then i've tried to flash an older version of the stock rom (android 7) due some problems in Android 8 (often some slow downs while operating)
- this doesn't work, the flash don't start
- therefore nothing should be happend, or?
- then i've can't get anymore in the stock recovery to wipe all data
...therefore the mess began:
* i can't flash TWRP anymore
* i can't flash stock recovery anymore
* i only can get into download mode
* i can only flash a certain rom type successfully (green PASS within odin), but with the final stuck with boot loop, with the mentioned blue screen
* other rom version can't flashed
I hopefully ask you guys here, if anyone can help me?
Any help would be very appreciated ...
Looking for some help please! My phone battery died the other day, I plugged it in to charge and turned it on at 3% battery life only to get stuck in a boot loop.
Did a factory reset and then successfully flashed with odin and current firmware G930TUVS9CSC1. After flashing it went to installing a system update screen only getting to about 32%, then it said erasing for a while and went back to the samsung startup screen stuck in apparently the same boot loop I started with.
Is my phone screwed or did I miss something? looking for any help, thanks.
vexcesban said:
Looking for some help please! My phone battery died the other day, I plugged it in to charge and turned it on at 3% battery life only to get stuck in a boot loop.
Did a factory reset and then successfully flashed with odin and current firmware G930TUVS9CSC1. After flashing it went to installing a system update screen only getting to about 32%, then it said erasing for a while and went back to the samsung startup screen stuck in apparently the same boot loop I started with.
Is my phone screwed or did I miss something? looking for any help, thanks.
Click to expand...
Click to collapse
It sometimes does this, make sure the firmware your using is correct for your device and flash again.
UNCHECK "auto reboot" in Odin
Disconnect when flash complete Do Not Turn The Phone On
Reboot into recovery volume up+home+power
Wipe cache/factory rest
Reboot
cooltt said:
It sometimes does this, make sure the firmware your using is correct for your device and flash again.
UNCHECK "auto reboot" in Odin
Disconnect when flash complete Do Not Turn The Phone On
Reboot into recovery volume up+home+power
Wipe cache/factory rest
Reboot
Click to expand...
Click to collapse
Thanks. Appreciate the input, but it didn't work for me after trying it twice. I am positive I have the right firmware.
It boots up with no led indicating light and continues to just flash the opening samsung screen for eternity.
Got the phone to boot up normally but now it wont read my sim card. sim works in my other phone. Any ideas?
vexcesban said:
Got the phone to boot up normally but now it wont read my sim card. sim works in my other phone. Any ideas?
Click to expand...
Click to collapse
SIM reader on phone, blow into hole to dislodge any dust and make sure sim is flat in adapter. Very rarely a software problem with sim not read.
cooltt said:
SIM reader on phone, blow into hole to dislodge any dust and make sure sim is flat in adapter. Very rarely a software problem with sim not read.
Click to expand...
Click to collapse
interesting, it worked fine before this started 2 days ago. I guess maybe the sim card reader broke? theres definitely no dirt in there and it seems to make a good connection (tried a new sim card had lying around and it etched lines into the sim card nicely).
Also I should mention that I had no clue what I was doing and flashed a dozen or so different versions of firmwares probably like 20 times, so maybe I caused it.
vexcesban said:
interesting, it worked fine before this started 2 days ago. I guess maybe the sim card reader broke? theres definitely no dirt in there and it seems to make a good connection (tried a new sim card had lying around and it etched lines into the sim card nicely).
Also I should mention that I had no clue what I was doing and flashed a dozen or so different versions of firmwares probably like 20 times, so maybe I caused it.
Click to expand...
Click to collapse
Er.... Yes!
You have to flash the correct region firmware for your device or you end up with problems like you have.
Search for the SamFirm tool on here it's great for getting the correct firmware direct from Samsung servers.
cooltt said:
Er.... Yes!
You have to flash the correct region firmware for your device or you end up with problems like you have.
Search for the SamFirm tool on here it's great for getting the correct firmware direct from Samsung servers.
Click to expand...
Click to collapse
Okay well that tool's forum post says it's deprecated so I followed the alternative link to updato and got stock 8.0 from there. Flashed phone, everything works 100% but still no sim detected.
I'm wondering If I broke my phone because I even tried some custom rom with a pit file and probably did that wrong as well.
vexcesban said:
Okay well that tool's forum post says it's deprecated so I followed the alternative link to updato and got stock 8.0 from there. Flashed phone, everything works 100% but still no sim detected.
I'm wondering If I broke my phone because I even tried some custom rom with a pit file and probably did that wrong as well.
Click to expand...
Click to collapse
PIT won't do anything to SIM.
Try all of these
Hey i am having the same problem odin flash with succes but the phone still only shows the first samsung glaxy s7 screen and then reboots.
Also i cant acces recovery.
i have the same problem
Huzalio said:
Hey i am having the same problem odin flash with succes but the phone still only shows the first samsung glaxy s7 screen and then reboots.
Also i cant acces recovery.
Click to expand...
Click to collapse
hi, did you find a way to fix it?
@cooltt I made an account here in order to thank you! I was stuck in a boot loop after flashing a stock ROM and your advice saved my phone. I thought I bricked it!!
q-l-p said:
@cooltt I made an account here in order to thank you! I was stuck in a boot loop after flashing a stock ROM and your advice saved my phone. I thought I bricked it!!
Click to expand...
Click to collapse
Glad I could help
cooltt said:
It sometimes does this, make sure the firmware your using is correct for your device and flash again.
UNCHECK "auto reboot" in Odin
Disconnect when flash complete Do Not Turn The Phone On
Reboot into recovery volume up+home+power
Wipe cache/factory rest
Reboot
Click to expand...
Click to collapse
I'm having this same issue but it won't boot into recovery at all, I don't know what to do.
iroveashe said:
I'm having this same issue but it won't boot into recovery at all, I don't know what to do.
Click to expand...
Click to collapse
First MAKE SURE you are flashing correct firmware for your device.
What device do you have and what country?
If you are sure it's correct. Flash again with Odin but uncheck "auto reboot" in options.
When pass appears just disconnect phone, it doesn't matter what it shows on the screen.
In this sequence press and hold the following... Volume down+home+power.
As soon as the screen goes black move your finger to Volume up while still pressing home+power. It may take several attempts.
When recovery menu appears wipe cache partition then reboot.
Leave phone go through boot sequence, ignore what appears on the screen during this time it is normal. This boot should take around 5 minutes.
EDIT: FIXED, I did what you did, but for that to work I had to flash it without the hidden.img. Then it rebooted and got stuck on the logo again, but i was able to boot into recovery. Thank you so much.
cooltt said:
First MAKE SURE you are flashing correct firmware for your device.
What device do you have and what country?
Click to expand...
Click to collapse
Hey, thank you for responding.
I'm not 100% sure it's the right one
Device: Samsung A510M
Country: Argentina
Carrier: Personal
I downloaded a firmware from sammobile matching those specifications, but it fails at the last step with hidden.img.
This morning I downloaded another firmware through samfirm, but that one fails at modem.img instead.
I will try your instructions with either of them.
---------- Post added at 07:01 PM ---------- Previous post was at 06:06 PM ----------
cooltt said:
As soon as the screen goes black move your finger to Volume up while still pressing home+power. It may take several attempts.
Click to expand...
Click to collapse
To be clear, I only need to repeat this part of the process, not reinstall the firmware every time, correct? I've been trying to do this for a while, but it just shows:
"An error has occurred while updating the device software. Use the Emergency recovery function in the Smart Switch PC software."