Database Info

Disabling Direct Push on Dolphin 9900 Handset

I have a Dolphin 9900 handset which runs WM 6.1. Each day at 12:00PM and 12:00AM the device turns on automatically. There are no e-mail accounts setup on this device. I have tried to disable Direct Push, assuming that's the reason for its issue, but nothing has worked. I have tried the following:
[HKEY_CURRENT_USER\ControlPanel\Notifications\Remin ders\AutoSnooze]
"AutoSnoozeMins"=dword:0
HKCU\ControlPanel\Notifications\{A877D65A239C-47a7-9304-0D347F580408}
set value "Options" to 20000000 (hexadecimal) or 536870912 (decimal)
And the steps found here:
The Exchange Security Policy (4131) updates the device policy:
HKLM\Security\Policies\00001023: 0 = Enabled; 1 = Disabled
To change the inactivity timer:
HKLM\Comm\Security\Policy\LASSD\AE\{50C13377-C66D-400C-889E-C316FC4AB374}\
AEFrequencyType: 0 = No inactivity time; 1 = Activity time enable
AEFrequencyValue: = number of minutes before timeout
To change the password strength policy:
HKLM\Comm\Security\Policy\LASSD\LAP\lap_pw\
MinimumPasswordLength: minimum number of characters in password (0 defaults to 1)
PasswordComplexity: 0 = Require Alphanumeric; 1 = Require numeric (PIN); 2 = No restriction
And finally to change the Device wipe settings:
HKLM\Comm\Security\Policy\LASSD\
DeviceWipeThreshold: -1 = disabled; (any positive number) = # failed attempts before device memory gets whacked
CodewordFrequency: # of attempts before a codeword is displayed to prevent accidental device wipe.
None of these steps worked as the device still turns on at 12:00 each time. Does anyone have any suggestions?

default wimax ##data# settings

Hopefully these will be useful if someone messed up theirs. Eventually after I update/root I will post any changes.
stock unrooted evo 4g
hardware 0003
baseband = 1.39.00.05.31
software = 1.32.651.6
pri = 1.40_003
prl = 60668
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeout(s) = 1
wimax scan retry(s) = 900
wimax idle sleep(s) = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
wimax entry delay(s) = 600
wimax exit cinr (db) = 2
wimax exit delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
obviously replace the 4g mac and username with your own.
--------------------------------------------
edit: after OTA update, some missing and modified settings
stock unrooted evo 4g
hardware 0003
baseband = 2.05.00.06.10
software = 1.47.651.6
pri = 1.40_003
prl = 60668
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
[STRIKE]spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76[/STRIKE]
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeout(s) = 1
[COLOR="SeaGreen"]wimax scan retry(s) = 300[/COLOR]
wimax idle sleep(s) = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
[COLOR="SeaGreen"]wimax entry delay(s) = 300[/COLOR]
wimax exit cinr (db) = 2
wimax exit delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
edit 2: added additional settings per request
------------------------------------
Code:
data profile
active profile = 1
username = [email protected]
spi mn-ha = 4d2
spi mn-aaa = 4d2
reverse tunnel preferred = enable
home ip address = 0.0.0.0
primary home agent = 255.255.255.255
second home agent = 68.28.89.76
dsa server url = https://dsa.spcsdns.net:443/dsa/
Code:
evdo
ddtm = disable
preferred mode = automatic
Code:
advanced
meid(hex) = your meid
p_rev = IS-2000 (6)
scm = 58
slot mode = enable
slot cycle index = 2
mcc (mobile country code) = 310
mnc (mobile network code) = 00
msid = (not sure if this is private so not posting)
accolc (access overload class) = 2
vocoder = enable
evrc-b = disable
home orig = evrc
roam orig = voice 13k
home sys registration = enable
foreign sid registration = enable
foreign nid registration = enable
mn ha spi set = enable
mn aaa spi set = enable
home side/nid #1 = 4139/65535
mms server url = http://mms.sprintpcs.com
rtsp proxy port = 554
rtsp proxy address = rtsp.vog.sprintpcs.com
http pd proxy port = 8085
http pd proxy address = pd.vog.sprintpcs.com
======================================
after froyo ota update
android version = 2.2
baseband = 2.15.00.07.28
kernel = 2.6.32.15-g746f4f0 [email protected] #58
build = 3.26.651.6 cl218634 release-keys
software = 3.26.651.6
browser = webkit3.1
pri = 1.40_003
prl = 60668
Code:
##data#
standby time (minutes) = 10
scan rate (minutes) = 30
NAI = [email protected]
user name = [email protected]
realm = sprintpcs.com
center frequency = 2647000,2657000,2667000
bandwidth = 10,10,10
napdis = 000002
nspdis = 000004
wimax_scan_attempt_timeout(s) = 1
[COLOR="Lime"]wimax_scan_retrys = 120[/COLOR]
wimax_idle_sleep(s) = 10
wimax_entry_rx(rssi)dbm = -89
wimax_entry_cinr(db) = 4
wimax_entry_delay(s) = 300
wimax_exit_cinr (db) = 2
wimax_exit_delay(s) = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable

Awesome thanks!
Swyped from my EVO via XDA app

When you root your PRI will roll back to 1.34

There is quite a few obvious entries that are missing on a rooted evo with 4g working.
Hmm
Interesting
James

added wimax data settings after applying OTA update

Thanks for this, it was a big help!
I had screwed with some settings and ended up not remembering what they were

Can some post the screen shots/info for the other settings under data plz, looking for default unmodified ones.

I thought these were the default unmodified settings?
~Jasecloud4

jasecloud4 said:
I thought these were the default unmodified settings?
~Jasecloud4
Click to expand...
Click to collapse
they prob are but i need the ones for evdo

stress1ner said:
Can some post the screen shots/info for the other settings under data plz, looking for default unmodified ones.
Click to expand...
Click to collapse
added info to first post

TeknoJnky said:
added info to first post
Click to expand...
Click to collapse
Good move not posting your MSID, it's private

my 4g isnt working after the simple root process. how might i go about figuring out why?

jbcain said:
my 4g isnt working after the simple root process. how might i go about figuring out why?
Click to expand...
Click to collapse
I would recommend flashing whitslacks rooted oem to make sure all the radios and such are up to date.
http://forum.xda-developers.com/showthread.php?t=715915
Once its all working from there, then you can try out other roms if you desire.

TeknoJnky said:
added info to first post
Click to expand...
Click to collapse
good looking out.

TeknoJnky said:
Code:
##data# > wimax settings
standby time (minute) = 10
scan rate (minute) = 30
NAI = [email protected]
username = [email protected]
realm = sprintpcs.com
[STRIKE]spi mn-aaa = 4D2
spi mn HA = 4D2
home ip address = 0.0.0.0
second home agent = 68.28.89.76[/STRIKE]
center frequency = 2647000,2657000,2667000
bandwidth = 10, 10, 10
napdis = 000002
nspdis = 000004
wimax scan attempt timeouts = 1
[COLOR="SeaGreen"]wimax scan retrys = 300[/COLOR]
wimax idle sleeps = 10
wimax entry rx (rssi) (dbm) = -89
wimax entry cinr (db) = 4
[COLOR="SeaGreen"]wimax entry delays = 300[/COLOR]
wimax exit cinr (db) = 2
wimax exist delays = 2
handoff threshold = 0
idle mode timer = 0
tls = enable
ttls = disable
Click to expand...
Click to collapse
Just FYI: If you change the WIMAX_scan_attempt_Timeout - the only valid entries are 5-300, so you won't be able to restore the default value of "1"

updated with froyo OTA defaults
only change noticed was
wimax_scan_retrys = 120 (from 300)

...and the update resets all values that were manually changed.

Question: How would the MN HA SPI Set and MN AAA SPI Set values be changed from Enable (stock) to Disable? I was checking speed downloads tonight on my Evo and my wife's and noticed are settings are different, but I didn't change my values manually something else did... All other settings are consistent.
Both phones are rooted and running MikFroyo 4.5.
I tried to google what those settings are even for, but didn't have much luck. Any help would be appreciated.

Question: What are the MN HA SPI Set and MN AAA SPI Set values for?
I was comparing download speeds on my wife's Evo and mine tonight after the latest PRL update and noticed our settings are different.
Her phone shows both values as Enable and mine show Disable. I have no idea how mine got changed.
I tried to google search but didn't find anything helpful. Any help would be appreciated.
Edit: Both of our phones are rooted and currently running MikFroyo 4.5.

Is there a way to disable 4G? My 4G keeps turning itself on and I *DONT* want it on EVER AGAIN.
SOLVED: Chaged 4G MAC to 00:00:00:00:00:00 and now it doesn't connect and after a few attemps it idles. Still haven't checked how much the battery drains... Another solution is to change the RSA key just 1 character will make it not connect. (both the MAC & RSA keys can be edited in wimax.img)

[Q] I need Galaxy S 4G Dialer/Menu Codes

I tired finding a thread to my second question but was unsuccessful again so here it is.
Does anyone know the galaxy S 4G Service Codes??? Thanks!

[email protected] said:
I tired finding a thread to my second question but was unsuccessful again so here it is.
Does anyone know the galaxy S 4G Service Codes??? Thanks!
Click to expand...
Click to collapse
~Samsung Mobile Global Codes~
*#1234# = Firmware Version.
*#2222# = H/W Version.
*#8999*8376263# = All Versions Together.
*#8999*8378# = Test Menu.
*#4777*8665# = GPSR Tool.
*#8999*523# = LCD Brightness.
*#8999*377# = Error Menu.
*#8999*327# = EEP Menu.
*#8999*667# = Debug Mode.
*#92782# = PhoneModel. (Wap)
#*5737425# = JAVA Mode.
*#2255# = Call List.
*#232337# = Bluetooth MAC Adress.
*#5282837# = Java Version.
#*4773# = Incremental Redundancy.
#*7752# = 8 PSK uplink capability bit.
#*7785# = Reset wakeup & RTK timer cariables/variables.
#*7200# = Tone Generator Mute.
#*3888# = BLUETOOTH Test mode.
#*7828# = Task screen.
#*#8377466# = S/W Version & H/W Version.
#*2562# = Restarts Phone.
#*2565# = No Blocking? General Defense.
#*3353# = General Defense, Code Erased.
#*3837# = Phone Hangs on White screen.
#*3849# = Restarts Phone.
#*3851# = Restarts Phone.
#*3876# = Restarts Phone.
#*7222# = Operation Typ: (Class C GSM)
#*7224# = !!! ERROR !!!
#*7252# = Operation Typ: (Class B GPRS)
#*7271# = CMD: (Not Available)
#*7274# = CMD: (Not Available)
#*7337# = Restarts Phone. (Resets Wap Settings)
#*2787# = CRTP ON/OFF.
#*2886# = AutoAnswer ON/OFF.
#*3737# = L1 AFC.
#*5133# = L1 HO Data.
#*7288# = GPRS Detached/Attached.
#*7287# = GPRS Attached.
#*7666# = White Screen.
#*7693# = Sleep Deactivate/Activate.
#*7284# = L1 HO Data.
#*2256# = Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# = Databattery.
#*2527# = GPRS switching set to (Class 4, 8, 9, 10)
#*2679# = Copycat feature Activa/Deactivate.
#*3940# = External looptest 9600 bps.
#*4263# = Handsfree mode Activate/Deactivate.
#*4700# = Please use function 2637.
#*7352# = BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# = Time ON.
#*3370# = Same as 4700.
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep.
#*7462# = SIM Phase.
#*7983# = Voltage/Freq.
#*7986# = Voltage.
#*8466# = Old Time.
#*2255# = Call Failed.
#*5187# = L1C2G trace Activate/Deactivate.
#*5376# = DELETE ALL SMS!!!!.
#*6837# = Official Software Version: (0003000016000702)
#*7524# = KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# = LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# = Permanent Registration Beep.
#*2474# = Charging Duration.
#*2834# = Audio Path. (Handsfree)
#*3270# = DCS Support Activate/Deactivate.
#*3282# = Data Activate/Deactivate.
#*3476# = EGSM Activate/Deactivate.
#*3676# = FORMAT FLASH VOLUME!!!
#*4760# = GSM Activate/Deactivate.
#*4864# = White Screen.
#*5171# = L1P1.
#*5172# = L1P2.
#*5173# = L1P3.
#*7326# = Accessory.
#*7683# = Sleep variable.
#*8465# = Time in L1.
#*2252# = Current CAL.
#*2836# = AVDDSS Management Activate/Deactivate.
#*3877# = Dump of SPY trace.
#*7728# = RSAV.
#*2677# = Same as 4700.
#*3728# = Time 2 Decod.
#*3725# = B4 last off.
#*7372# = Resetting the time to DPB variables.
#*7732# = Packet flow context bit Activate/Deactivate.
#*6833# = New uplink establishment Activate/Deactivate.
#*3273# = EGPRS multislot. (Class 4, 8, 9, 10)
#*7722# = RLC bitmap compression Activate/Deactivate.
#*2351# = Blinks 1347E201 in RED.
#*4472# = Hysteresis of serving cell: 3 dB
#*2775# = Switch to 2 inner speaker.
#*9270# = Force WBS.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3757# = DSL UART speed set to. (LOW, HIGH)
#*8726# = Switches USBACM to Normal.
#*8724# = Switches USBACM to Generator mode.
#*8727# = Switches USBACM to Slink mode.
#*8725# = Switches USBACM to Loop-back mode.
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*8370# = Tfs4.0 Test 0.
#*8371# = Tfs4.0 Test 1.
#*8372# = Tfs4.0 Test 2.
#*8373# = Tfs4.0 Test 3.
#*8374# = Tfs4.0 Test 4.
#*8375# = Tfs4.0 Test 5.
#*8376# = Tfs4.0 Test 6.
#*8377# = Tfs4.0 Test 7.
#*8378# = Tfs4.0 Test 8.
#*8379# = Tfs4.0 Test 9.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*22671# = AMR REC START.
#*22672# = Stop AMR REC. (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# = Pause REC.
#*22674# = Resume REC.
#*22675# = AMR Playback.
#*22676# = AMR Stop Play.
#*22677# = Pause Play.
#*22678# = Resume Play.
#*77261# = PCM Rec Req.
#*77262# = Stop PCM Rec.
#*77263# = PCM Playback.
#*77264# = PCM Stop Play.
#*22679# = AMR Get Time.
*#8999*364# = Watchdog ON/OFF.
*#8999*427# = WATCHDOG signal route setup.
*2767*226372# = Camera Reset. (deletes photos)
*2767*3855# = E2P Full Reset.
*2767*2878# = E2P Custom Reset.
*2767*927# = E2P Wap Reset.
*2767*226372# = E2P Camera Reset.
*2767*688# = Reset Mobile TV.
#7263867# = RAM Dump. (On or Off)
~Samsung Mobile Lock Codes~
*#7465625# = Check the locks.
*7465625*638*Code# = Enables Network lock.
#7465625*638*Code# = Disables Network lock.
*7465625*782*Code# = Enables Subset lock.
#7465625*782*Code# = Disables Subset lock.
*7465625*77*Code# = Enables SP lock.
#7465625*77*Code# = Disables SP lock.
*7465625*27*Code# = Enables CP lock.
#7465625*27*Code# = Disables CP lock.
*7465625*746*Code# = Enables SIM lock.
#7465625*746*Code# = Disables SIM lock.
*7465625*228# = Activa lock ON.
#7465625*228# = Activa lock OFF.
*7465625*28638# = Auto Network lock ON.
#7465625*28638# = Auto Network lock OFF.
*7465625*28782# = Auto subset lock ON.
#7465625*28782# = Auto subset lock OFF.
*7465625*2877# = Auto SP lock ON.
#7465625*2877# = Auto SP lock OFF.
*7465625*2827# = Auto CP lock ON.
#7465625*2827# = Auto CP lock OFF.
*7465625*28746# = Auto SIM lock ON.
#7465625*28746# = Auto SIM lock OFF.
~Samsung Mobile MMS Codes~
*2767*43927# = Austria WAP Settings.
*2767*420927# = Czech WAP Settings.
*2767*33927# = France WAP Settings.
*2767*49927# = Germany WAP Settings.
*2767*30927# = Greece WAP Settings.
*2767*39927# = Italy WAP Settings.
*2767*31927# = Netherlands WAP Settings.
*2767*351927# = Portugal WAP Settings.
*2767*7927# = Russia WAP Settings.
*2767*34927# = Spain WAP Settings.
*2767*46927# = Sweden WAP Settings.
*2767*44927# = UK WAP Settings.
*2767*380927# = Ukraine WAP Settings.
*2767*73738927# = WAP Settings Reset.
*2767*43667# = Austria MMS Settings.
*2767*420667# = Czech MMS Settings.
*2767*33667# = France MMS Settings.
*2767*49667# = Germany MMS Settings.
*2767*30667# = Greece MMS Settings.
*2767*39667# = Italy MMS Settings.
*2767*31667# = Netherlands MMS Settings.
*2767*351667# = Portugal MMS Settings.
*2767*7667# = Russia MMS Settings.
*2767*34667# = Spain MMS Settings.
*2767*46667# = Sweden MMS Settings.
*2767*44667# = UK MMS Settings.
*2767*380667# = Ukraine MMS Settings.
~Samsung Mobile Sound Codes~
Dial *#6984125*#
Test menu dial *#9072641*# (You need this one i think.)
Click 5 Audio - 2 AP volume config
Now you see zie je 4 things:
1 RCV config
2 EAR config
3 SPK config
4 BTH config
Now you see this:
1 MP volume
2 Keytone volume
3 Ringtone volume
4 Rec volume
5 FM radio volume
6 Camera volume
7 Voice call volume
8 Vt call volume
9 Voice memo volume
( SPK = Speaker )( Ear = Headset )
Tune Headset volume:
*#9072641*# - 2 EAR config - 3 Ringtone volume - Stap 6 tune it to 10
Tune movie volume:
*#9072641*# - 3 SPK config - 3 Ringtone volume - Stap 6 tune it to 10
Note it works but don't forget to type somewhere your old settings.
~Samsung Mobile Email Codes~
#*36245# Turns Email TestMenu on.
*2767*22236245# Email EPP set (....)!
*2767*837836245# Email Test Account!
*2767*29536245# Email Test2 Account!
*2767*036245# Email EPP reset!
*2767*136245# Email EPP set (1)!
*2767*736245# Email EPP set (7)!
*2767*3036245# Email...
*2767*3136245# Email...
*2767*3336245# Email...
*2767*3436245# Email...
*2767*3936245# Email...
*2767*4136245# Email...
*2767*4336245# Email...
*2767*4436245# Email...
*2767*4536245# Email...
*2767*4636245# Email...
*2767*4936245# Email...
*2767*6036245# Email...
*2767*6136245# Email...
*2767*6236245# Email...
*2767*6336245# Email...
*2767*6536245# Email...
*2767*6636245# Email...
*2767*8636245# Email...
*2767*85236245# Email...

Don't work...
luckyduck69 said:
~Samsung Mobile Global Codes~
*#1234# = Firmware Version.
*#2222# = H/W Version.
*#8999*8376263# = All Versions Together.
*#8999*8378# = Test Menu.
*#4777*8665# = GPSR Tool.
*#8999*523# = LCD Brightness.
*#8999*377# = Error Menu.
*#8999*327# = EEP Menu.
*#8999*667# = Debug Mode.
*#92782# = PhoneModel. (Wap)
#*5737425# = JAVA Mode.
*#2255# = Call List.
*#232337# = Bluetooth MAC Adress.
*#5282837# = Java Version.
#*4773# = Incremental Redundancy.
#*7752# = 8 PSK uplink capability bit.
#*7785# = Reset wakeup & RTK timer cariables/variables.
#*7200# = Tone Generator Mute.
#*3888# = BLUETOOTH Test mode.
#*7828# = Task screen.
#*#8377466# = S/W Version & H/W Version.
#*2562# = Restarts Phone.
#*2565# = No Blocking? General Defense.
#*3353# = General Defense, Code Erased.
#*3837# = Phone Hangs on White screen.
#*3849# = Restarts Phone.
#*3851# = Restarts Phone.
#*3876# = Restarts Phone.
#*7222# = Operation Typ: (Class C GSM)
#*7224# = !!! ERROR !!!
#*7252# = Operation Typ: (Class B GPRS)
#*7271# = CMD: (Not Available)
#*7274# = CMD: (Not Available)
#*7337# = Restarts Phone. (Resets Wap Settings)
#*2787# = CRTP ON/OFF.
#*2886# = AutoAnswer ON/OFF.
#*3737# = L1 AFC.
#*5133# = L1 HO Data.
#*7288# = GPRS Detached/Attached.
#*7287# = GPRS Attached.
#*7666# = White Screen.
#*7693# = Sleep Deactivate/Activate.
#*7284# = L1 HO Data.
#*2256# = Calibration info? (For CMD set DEBUGAUTONOMY in cihard.opt)
#*2286# = Databattery.
#*2527# = GPRS switching set to (Class 4, 8, 9, 10)
#*2679# = Copycat feature Activa/Deactivate.
#*3940# = External looptest 9600 bps.
#*4263# = Handsfree mode Activate/Deactivate.
#*4700# = Please use function 2637.
#*7352# = BVMC Reg value (LOW_SWTOFF, NOMINAL_SWTOFF)
#*2558# = Time ON.
#*3370# = Same as 4700.
#*3941# = External looptest 115200 bps
#*5176# = L1 Sleep.
#*7462# = SIM Phase.
#*7983# = Voltage/Freq.
#*7986# = Voltage.
#*8466# = Old Time.
#*2255# = Call Failed.
#*5187# = L1C2G trace Activate/Deactivate.
#*5376# = DELETE ALL SMS!!!!.
#*6837# = Official Software Version: (0003000016000702)
#*7524# = KCGPRS: (FF FF FF FF FF FF FF FF 07)
#*7562# = LOCI GPRS: (FF FF FF FF FF FF FF FF FF FF FF FE FF 01)
#*2337# = Permanent Registration Beep.
#*2474# = Charging Duration.
#*2834# = Audio Path. (Handsfree)
#*3270# = DCS Support Activate/Deactivate.
#*3282# = Data Activate/Deactivate.
#*3476# = EGSM Activate/Deactivate.
#*3676# = FORMAT FLASH VOLUME!!!
#*4760# = GSM Activate/Deactivate.
#*4864# = White Screen.
#*5171# = L1P1.
#*5172# = L1P2.
#*5173# = L1P3.
#*7326# = Accessory.
#*7683# = Sleep variable.
#*8465# = Time in L1.
#*2252# = Current CAL.
#*2836# = AVDDSS Management Activate/Deactivate.
#*3877# = Dump of SPY trace.
#*7728# = RSAV.
#*2677# = Same as 4700.
#*3728# = Time 2 Decod.
#*3725# = B4 last off.
#*7372# = Resetting the time to DPB variables.
#*7732# = Packet flow context bit Activate/Deactivate.
#*6833# = New uplink establishment Activate/Deactivate.
#*3273# = EGPRS multislot. (Class 4, 8, 9, 10)
#*7722# = RLC bitmap compression Activate/Deactivate.
#*2351# = Blinks 1347E201 in RED.
#*4472# = Hysteresis of serving cell: 3 dB
#*2775# = Switch to 2 inner speaker.
#*9270# = Force WBS.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3757# = DSL UART speed set to. (LOW, HIGH)
#*8726# = Switches USBACM to Normal.
#*8724# = Switches USBACM to Generator mode.
#*8727# = Switches USBACM to Slink mode.
#*8725# = Switches USBACM to Loop-back mode.
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*8370# = Tfs4.0 Test 0.
#*8371# = Tfs4.0 Test 1.
#*8372# = Tfs4.0 Test 2.
#*8373# = Tfs4.0 Test 3.
#*8374# = Tfs4.0 Test 4.
#*8375# = Tfs4.0 Test 5.
#*8376# = Tfs4.0 Test 6.
#*8377# = Tfs4.0 Test 7.
#*8378# = Tfs4.0 Test 8.
#*8379# = Tfs4.0 Test 9.
#*7878# = FirstStartup. (0=NO, 1=YES)
#*3838# = Blinks 3D030300 in RED.
#*2077# = GPRS Switch.
#*2027# = GPRS Switch.
#*0227# = GPRS Switch.
#*0277# = GPRS Switch.
#*22671# = AMR REC START.
#*22672# = Stop AMR REC. (File name: /a/multimedia/sounds/voice list/ENGMODE.amr)
#*22673# = Pause REC.
#*22674# = Resume REC.
#*22675# = AMR Playback.
#*22676# = AMR Stop Play.
#*22677# = Pause Play.
#*22678# = Resume Play.
#*77261# = PCM Rec Req.
#*77262# = Stop PCM Rec.
#*77263# = PCM Playback.
#*77264# = PCM Stop Play.
#*22679# = AMR Get Time.
*#8999*364# = Watchdog ON/OFF.
*#8999*427# = WATCHDOG signal route setup.
*2767*226372# = Camera Reset. (deletes photos)
*2767*3855# = E2P Full Reset.
*2767*2878# = E2P Custom Reset.
*2767*927# = E2P Wap Reset.
*2767*226372# = E2P Camera Reset.
*2767*688# = Reset Mobile TV.
#7263867# = RAM Dump. (On or Off)
~Samsung Mobile Lock Codes~
*#7465625# = Check the locks.
*7465625*638*Code# = Enables Network lock.
#7465625*638*Code# = Disables Network lock.
*7465625*782*Code# = Enables Subset lock.
#7465625*782*Code# = Disables Subset lock.
*7465625*77*Code# = Enables SP lock.
#7465625*77*Code# = Disables SP lock.
*7465625*27*Code# = Enables CP lock.
#7465625*27*Code# = Disables CP lock.
*7465625*746*Code# = Enables SIM lock.
#7465625*746*Code# = Disables SIM lock.
*7465625*228# = Activa lock ON.
#7465625*228# = Activa lock OFF.
*7465625*28638# = Auto Network lock ON.
#7465625*28638# = Auto Network lock OFF.
*7465625*28782# = Auto subset lock ON.
#7465625*28782# = Auto subset lock OFF.
*7465625*2877# = Auto SP lock ON.
#7465625*2877# = Auto SP lock OFF.
*7465625*2827# = Auto CP lock ON.
#7465625*2827# = Auto CP lock OFF.
*7465625*28746# = Auto SIM lock ON.
#7465625*28746# = Auto SIM lock OFF.
~Samsung Mobile MMS Codes~
*2767*43927# = Austria WAP Settings.
*2767*420927# = Czech WAP Settings.
*2767*33927# = France WAP Settings.
*2767*49927# = Germany WAP Settings.
*2767*30927# = Greece WAP Settings.
*2767*39927# = Italy WAP Settings.
*2767*31927# = Netherlands WAP Settings.
*2767*351927# = Portugal WAP Settings.
*2767*7927# = Russia WAP Settings.
*2767*34927# = Spain WAP Settings.
*2767*46927# = Sweden WAP Settings.
*2767*44927# = UK WAP Settings.
*2767*380927# = Ukraine WAP Settings.
*2767*73738927# = WAP Settings Reset.
*2767*43667# = Austria MMS Settings.
*2767*420667# = Czech MMS Settings.
*2767*33667# = France MMS Settings.
*2767*49667# = Germany MMS Settings.
*2767*30667# = Greece MMS Settings.
*2767*39667# = Italy MMS Settings.
*2767*31667# = Netherlands MMS Settings.
*2767*351667# = Portugal MMS Settings.
*2767*7667# = Russia MMS Settings.
*2767*34667# = Spain MMS Settings.
*2767*46667# = Sweden MMS Settings.
*2767*44667# = UK MMS Settings.
*2767*380667# = Ukraine MMS Settings.
~Samsung Mobile Sound Codes~
Dial *#6984125*#
Test menu dial *#9072641*# (You need this one i think.)
Click 5 Audio - 2 AP volume config
Now you see zie je 4 things:
1 RCV config
2 EAR config
3 SPK config
4 BTH config
Now you see this:
1 MP volume
2 Keytone volume
3 Ringtone volume
4 Rec volume
5 FM radio volume
6 Camera volume
7 Voice call volume
8 Vt call volume
9 Voice memo volume
( SPK = Speaker )( Ear = Headset )
Tune Headset volume:
*#9072641*# - 2 EAR config - 3 Ringtone volume - Stap 6 tune it to 10
Tune movie volume:
*#9072641*# - 3 SPK config - 3 Ringtone volume - Stap 6 tune it to 10
Note it works but don't forget to type somewhere your old settings.
~Samsung Mobile Email Codes~
#*36245# Turns Email TestMenu on.
*2767*22236245# Email EPP set (....)!
*2767*837836245# Email Test Account!
*2767*29536245# Email Test2 Account!
*2767*036245# Email EPP reset!
*2767*136245# Email EPP set (1)!
*2767*736245# Email EPP set (7)!
*2767*3036245# Email...
*2767*3136245# Email...
*2767*3336245# Email...
*2767*3436245# Email...
*2767*3936245# Email...
*2767*4136245# Email...
*2767*4336245# Email...
*2767*4436245# Email...
*2767*4536245# Email...
*2767*4636245# Email...
*2767*4936245# Email...
*2767*6036245# Email...
*2767*6136245# Email...
*2767*6236245# Email...
*2767*6336245# Email...
*2767*6536245# Email...
*2767*6636245# Email...
*2767*8636245# Email...
*2767*85236245# Email...
Click to expand...
Click to collapse
Nearly all of these codes don't work on my sgs4g... Im running GB 2.3.5 ROM with KJ1 kernel. Does that make a difference?

Search sgs secret codes on the market.
Sent from my SGH-T959V using xda premium

Please use the Q&A Forum for questions Thanks
Moving to Q&A

Updated 2011 List of Samsung Secret Codes For All Phones, includes Galaxy S II

Find Samsung’s MAC Address
Step 1 ) Go to the phone’s dialpad like you’re about to call someone.
Step 2 ) Press *#2222#
Step 3 ) Press Menu key
Step 4 ) Press WiFi
Find IMEI
Step 1 ) Go to the phone’s dialpad like you’re about to call someone.
Step 2 ) Press *#06#
Go to the phone’s dialpad and press….
*#232337# Find Bluetooth MAC Address
More Codes:
Software version: *#9999#
IMEI number: *#06#
Serial number: *#0001#
Battery status- Memory capacity : *#9998*246#
Debug screen: *#9998*324# – *#8999*324#
LCD kontrast: *#9998*523#
Vibration test: *#9998*842# – *#8999*842#
Alarm beeper – Ringtone test : *#9998*289# – *#8999*289#
Smiley: *#9125#
Software version: *#0837#
Display contrast: *#0523# – *#8999*523#
Battery info: *#0228# or *#8999*228#
Display storage capacity: *#8999*636#
Display SIM card information: *#8999*778#
Show date and alarm clock: *#8999*782#
The display during warning: *#8999*786#
Samsung hardware version: *#8999*837#
Show network information: *#8999*638#
Display received channel number and received intensity: *#8999*9266#
*#1111# S/W Version
*#1234# Firmware Version
*#2222# H/W Version
*#8999*8376263# All Versions Together
*#8999*8378# Test Menu
*#4777*8665# GPSR Tool
*#8999*523# LCD Brightness
*#8999*377# Error LOG Menu
*#8999*327# EEP Menu
*#8999*667# Debug Mode
*#92782# PhoneModel (Wap)
#*5737425# JAVA Mode
*#2255# Call List
*#232337# Bluetooth MAC Adress
*#5282837# Java Version
Type in *#0000# on a Samsung A300 to reset the language
Master reset(unlock) #*7337# (for the new samsungs E700 x600 but not E710)
Samsung E700 type *#2255# to show secret call log (not tested)
Samsung A300, A800 phone unlock enter this *2767*637#
Samsung V200, S100, S300 phone unlock : *2767*782257378#
...(more)

Great post! Thanks!

[HOW-TO][GUIDE] - Samsung S4 Dial pad Phone Codes Discussion

This is a discussion thread dealing with and related to
all of the Secret Codes for the Samsung Galaxy S4
Here you will find all of the official dial pad codes for
Samsung Galaxy S4 and other Samsung phones​
Here is a complete listing of these codes:
----------------------------------------------------------------------
*#06# Shows IMEI (International Mobile Equipment Identity) number
*#0*# LCD Test Menu
Dial the secret code *#0*#. Now you get a screen with title LCD TEST as shown in image and
below that you have lots of option to test various hardware parts of your phone such as speaker, sensor, lcd, etc
*#8999*523# LCD Brightness
*#1234# To check Software and Hardware information, PDA, CSC, MODEM (Firmware Version)
*#2222# H/W Version
*#*#4636#*#* user statistics and Phone Info
*#0011# Displays status information for the GSM
*#7780# Factory Reset
*2767*3855# Full factory reset (Don’t dial unless you have problem, it does not ask you to confirm )
*#12580*369# SW & HW Info
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*5376# DELETE ALL SMS!!!!
*#197328640# Service Mode
*#0228# Battery status (ADC, RSSI reading)
*#32489# Service mode (Ciphering Info)
*#2255# Call List
#*3888# BLUETOOTH Test mode
#*7828# Task screen
*#5282837# Java Version
*#232337# Bluetooth MAC Adress
*#232331# Bluetooth Test Mode
*#232338# WLAN MAC Address
*#232339# WLAN Test Mode
*#8999*8378# Test Menu
*#0842# Vibra Motor Test Mode
*#0782# Real Time Clock Test
*#0673# Audio Test Mode
*#0*# General Test Mode
*#2263# RF Band Selection / Network modes select
*#9090# Diagnostic ConfiguratioN
*#7284# USB I2C Mode Control
*#872564# USB Logging Control
*#4238378# GCF Configuration
*#0283# Audio Loopback Control
*#1575# GPS Control Menu
*#3214789650# LBS Test Mode
*#745# RIL Dump Menu
*#746# Debug Dump Menu
*#9900# Takes you to System Dump, where Disabling Fast Dormancy gives a boost to your network
speed on some networks (both wifi and Gprs), same code to re-enable it
*#44336# Sofware Version Info
*#0289# Melody Test Mode
*#2663# TSP / TSK firmware update
*#03# NAND Flash S/N
*#0589# Light Sensor Test Mode
*#0588# Proximity Sensor Test Mode
*#273283*255*3282*# Data Create Menu
*#273283*255*663282*# Data Create SD Card
*#3282*727336*# Data Usage Status
*#7594# Remap Shutdown to End Call TSK
*#34971539# Camera Firmware Update
*#526# WLAN Engineering Mode
*#528# WLAN Engineering Mode
*#7412365# Camera Firmware Menu
*#07# Test History
*#3214789# GCF Mode Status
*#272886# Auto Answer Selection
*#8736364# OTA Update Menu
*#301279# HSDPA/HSUPA Control Menu
*#7353# Quick Test Menu
*2767*4387264636# Sellout SMS / PCODE view
*#7465625# View Phone Lock Status
*7465625*638*# Configure Network Lock MCC/MNC
#7465625*638*# Insert Network Lock Keycode
*7465625*782*# Configure Network Lock NSP
#7465625*782*# Insert Partitial Network Lock Keycode
*7465625*77*# Insert Network Lock Keycode SP
#7465625*77*# Insert Operator Lock Keycode
*7465625*27*# Insert Network Lock Keycode NSP/CP
#7465625*27*# Insert Content Provider Keycode
*#272*IMEI# then we will get buyer code (For samsung galaxy sIII csc code)
*#*#7780#*#* Factory data reset – Clears Google-account data, system and program
settings and installed programs. system will not be deleted, and OEM programs, as well
as My Documents (pictures, music, videos)​
Feel free to post any questions or comments you may have relating to these codes.

Is anyone else having trouble getting these to work on kangakat or kit Kat in general? I had them working fine in kangabean and used it to diagnose a miscalibrated proximity sensor (that I then was able to reset)

Thank you for the list.

I'm on an att business account and have the ability to dial *data# to get a data usage report via sms. Thanks for the list!

How bout giving him a thanks on the forums lol...
mf3 rooted SHOstock 2.3

USSD codes are either carrier-specific or phone-specific.
However, my understanding is that the catch is that phone-specific means the stock ROM, not just the physical phone. So if you're running another ROM, phone-specific USSD codes may not work.
I've got CM 10.1.3, and I have not found a single phone-specific USSD code that works.

Cool
Thanks For Sharing Sir

*#8736364# OTA Update Menu
Sir,
I Need Your Help *#8736364# OTA Update Menu On AT&T S4
I Am In INDIA .. I Can't Update My Phone Via OTA Because I Unlocked My AT&T S4..
If I Change Any Setting On OTA Update Menu After I Will Get Update ?
---------- Post added at 12:21 PM ---------- Previous post was at 12:18 PM ----------
Misterjunky said:
This is a discussion thread dealing with and related to
all of the Secret Codes for the Samsung Galaxy S4
Here you will find all of the official dial pad codes for
Samsung Galaxy S4 and other Samsung phones​
Here is a complete listing of these codes:
----------------------------------------------------------------------
*#06# Shows IMEI (International Mobile Equipment Identity) number
*#0*# LCD Test Menu
Dial the secret code *#0*#. Now you get a screen with title LCD TEST as shown in image and
below that you have lots of option to test various hardware parts of your phone such as speaker, sensor, lcd, etc
*#8999*523# LCD Brightness
*#1234# To check Software and Hardware information, PDA, CSC, MODEM (Firmware Version)
*#2222# H/W Version
*#*#4636#*#* user statistics and Phone Info
*#0011# Displays status information for the GSM
*#7780# Factory Reset
*2767*3855# Full factory reset (Don’t dial unless you have problem, it does not ask you to confirm )
*#12580*369# SW & HW Info
#*#8377466# S/W Version & H/W Version
#*2562# Restarts Phone
#*3849# Restarts Phone
#*3851# Restarts Phone
#*3876# Restarts Phone
#*5376# DELETE ALL SMS!!!!
*#197328640# Service Mode
*#0228# Battery status (ADC, RSSI reading)
*#32489# Service mode (Ciphering Info)
*#2255# Call List
#*3888# BLUETOOTH Test mode
#*7828# Task screen
*#5282837# Java Version
*#232337# Bluetooth MAC Adress
*#232331# Bluetooth Test Mode
*#232338# WLAN MAC Address
*#232339# WLAN Test Mode
*#8999*8378# Test Menu
*#0842# Vibra Motor Test Mode
*#0782# Real Time Clock Test
*#0673# Audio Test Mode
*#0*# General Test Mode
*#2263# RF Band Selection / Network modes select
*#9090# Diagnostic ConfiguratioN
*#7284# USB I2C Mode Control
*#872564# USB Logging Control
*#4238378# GCF Configuration
*#0283# Audio Loopback Control
*#1575# GPS Control Menu
*#3214789650# LBS Test Mode
*#745# RIL Dump Menu
*#746# Debug Dump Menu
*#9900# Takes you to System Dump, where Disabling Fast Dormancy gives a boost to your network
speed on some networks (both wifi and Gprs), same code to re-enable it
*#44336# Sofware Version Info
*#0289# Melody Test Mode
*#2663# TSP / TSK firmware update
*#03# NAND Flash S/N
*#0589# Light Sensor Test Mode
*#0588# Proximity Sensor Test Mode
*#273283*255*3282*# Data Create Menu
*#273283*255*663282*# Data Create SD Card
*#3282*727336*# Data Usage Status
*#7594# Remap Shutdown to End Call TSK
*#34971539# Camera Firmware Update
*#526# WLAN Engineering Mode
*#528# WLAN Engineering Mode
*#7412365# Camera Firmware Menu
*#07# Test History
*#3214789# GCF Mode Status
*#272886# Auto Answer Selection
*#8736364# OTA Update Menu
*#301279# HSDPA/HSUPA Control Menu
*#7353# Quick Test Menu
*2767*4387264636# Sellout SMS / PCODE view
*#7465625# View Phone Lock Status
*7465625*638*# Configure Network Lock MCC/MNC
#7465625*638*# Insert Network Lock Keycode
*7465625*782*# Configure Network Lock NSP
#7465625*782*# Insert Partitial Network Lock Keycode
*7465625*77*# Insert Network Lock Keycode SP
#7465625*77*# Insert Operator Lock Keycode
*7465625*27*# Insert Network Lock Keycode NSP/CP
#7465625*27*# Insert Content Provider Keycode
*#272*IMEI# then we will get buyer code (For samsung galaxy sIII csc code)
*#*#7780#*#* Factory data reset – Clears Google-account data, system and program
settings and installed programs. system will not be deleted, and OEM programs, as well
as My Documents (pictures, music, videos)​
Feel free to post any questions or comments you may have relating to these codes.
Click to expand...
Click to collapse
Sir,
I Need Your Help *#8736364# OTA Update Menu On AT&T S4
I Am In INDIA .. I Can't Update My Phone Via OTA Because I Unlocked My AT&T S4..
If I Change Any Setting On OTA Update Menu After I Will Get Update ?
Please Please Please

Actually for some reason I can't get the majority of the codes to work on my 2 Galaxy S4s, which are running on 4.2.2 and 4.4.2 respectively. I was particularly interested in the factory reset codes because of some ongoing demo work in current Android vulnerabilities, but similarly there is no response from the dialler after entering the code.

Factory reset codes do not work, as well, on my S4 mini 9195 with 4.2.2.
Anybody knows working codes, or we should use Settings - Accounts - Backup and reset, or Recovery Mode reset option?

Nice.

It should be noted that a lot of them won't work on certain modems. When I went to mk2, I was locked out of service mode. So i have been using MDL modem to have access to more codes.
For instance running mk2 modem, when I would try *#9090# menu back, menu back, menu back, key input 1. My phone would reboot every time. Now on MDL modem. I have access again. The were other codes that did the same don't remember them.
Seems att/Samsung locked you out after each modem update.
Sent from my Nexus 7 using XDA Free mobile app

Not so good
Hi
Sorry to tell you that most of these codes don't work on my GT-I9505.
The phone has a rooted stock ROM.

jack_ssl said:
Sir,
I Need Your Help *#8736364# OTA Update Menu On AT&T S4
I Am In INDIA .. I Can't Update My Phone Via OTA Because I Unlocked My AT&T S4..
If I Change Any Setting On OTA Update Menu After I Will Get Update ?
---------- Post added at 12:21 PM ---------- Previous post was at 12:18 PM ----------
Sir,
I Need Your Help *#8736364# OTA Update Menu On AT&T S4
I Am In INDIA .. I Can't Update My Phone Via OTA Because I Unlocked My AT&T S4..
If I Change Any Setting On OTA Update Menu After I Will Get Update ?
Please Please Please
Click to expand...
Click to collapse
I don't think that Is a problem. Im in Bolivia with an unlocked sgh-i337 and received the NI1 update.

I'm in Virginia Beach, Virginia USA I have a T Mobile SGHM919 running rooted, with the sickness ROM v3 and v5 sickness theme on the dialer when I enter any code nothing happens unless unless call, when I press call it says " unable to process request" anybody know why? Fob I need to be all stock again to do it? I'm trying unlock my phone because I nerd yp leavevyhe crappy service I get from T Mobile
Sent from my SGH-M919 using XDA Free mobile app

Please Help Me
emptyPD said:
I don't think that Is a problem. Im in Bolivia with an unlocked sgh-i337 and received the NI1 update.
Click to expand...
Click to collapse
Sir , You Bought AT&T S4 From USA .. Then You Unlocked .. Came To Bolivia .. Still You Are Getting Update .. How Still You Are Using AT&T SIM CARD .. Pleas e Help Me