Hello,
I have been working with Motorola devices and fastboot for several years, but I have never seen a situation like this.
I recently sold a RAZR HD to a customer that was stock but rooted and bootloader unlocked. Without consulting me, he proceeded to install some bad software that is now causing endless freezing and force closing when the phone is powered on. I told him I would take the phone back to flash new firmware to the device.
First, I started by erasing userdata and cache with mfastboot. Both commands succeeded. Then, I rebooted the device.. and all of his apps and software were still installed! Confused, I booted to the stock recovery and wiped data and cache there. After rebooting, all of the apps were still installed! This is where I decided to nuke it with the latest firmware in RSD lite. The phone rebooted again with all of the software installed. I then tried flashing CWM recovery to the recovery partition, but when I tried booting to recovery, it was still the stock recovery.
To make a long story short, this phone acts like it is accepting and processing my mfastboot commands, but the phone seems infected with these apps and data and I cannot erase them. Not even a full SBF in RSD lite was able to clear the bad apps.
Are there any special commands with fastboot that I can try to get this device cleared out? Has anyone ever seen something like this before?
Thanks in advance.
boostedcx said:
Hello,
I have been working with Motorola devices and fastboot for several years, but I have never seen a situation like this.
I recently sold a RAZR HD to a customer that was stock but rooted and bootloader unlocked. Without consulting me, he proceeded to install some bad software that is now causing endless freezing and force closing when the phone is powered on. I told him I would take the phone back to flash new firmware to the device.
First, I started by erasing userdata and cache with mfastboot. Both commands succeeded. Then, I rebooted the device.. and all of his apps and software were still installed! Confused, I booted to the stock recovery and wiped data and cache there. After rebooting, all of the apps were still installed! This is where I decided to nuke it with the latest firmware in RSD lite. The phone rebooted again with all of the software installed. I then tried flashing CWM recovery to the recovery partition, but when I tried booting to recovery, it was still the stock recovery.
To make a long story short, this phone acts like it is accepting and processing my mfastboot commands, but the phone seems infected with these apps and data and I cannot erase them. Not even a full SBF in RSD lite was able to clear the bad apps.
Are there any special commands with fastboot that I can try to get this device cleared out? Has anyone ever seen something like this before?
Thanks in advance.
Click to expand...
Click to collapse
Other than fastboot erase commands to erase each partition, I have no earthly idea. Sounds like possibly partitions got corrupted or something. I'd ask the guy specifically what has he done to the phone since he received it? Sounds to me like he borked it up pretty good.
This is one of the reasons why I don't sell my devices to other people, but rather, trade them in. I just don't want to deal with the hassles it causes, especially if they borked it and then try to say that's how you gave it to them.
Is there anyway to flash a new partition file to this device similar to how Samsung devices can flash a .pit file in Odin? I agree that the partitions or partition table seem corrupted.
I flashed the JB 4.1.2 OTA in RSD lite last night, and it was successful, but when the phone rebooted it was still on KK with all the same apps. I tried "mfastboot erase system", but I got a permission denied error. Anyone have any other tips?
It sounds like the phone is in a read-only state. This has popped up a few times lately. As far as I know, no one had recovered.
Sent from my HTC6525LVW using Tapatalk
Related
Hi all,
I have a Xoom, running one of the nightlies from Team EOS (#34) and it was running fine until it started to get a lot of force closes. I figured thats fine ... I'm running a nightly, but then I started noticing that when I delete or install apps, then do a reboot, the apps are either not there (if I'd done an install) or still there (if I'd removed).
So then I figured, oh well, high time I got up to the latest nightly or even the stable build, and tried that, but low and behold after flashing the stable version of the Team EOS rom, when I booted back into the OS it was still the nightly #34.
So I tried restoring to the stock Motorola rom via fastboot, same result: booted into the OS on nightly #34. I tried a simple factory reset but when I boot back in all my data is still there.
So this is what I've tried:
- install Team EOS 1.0.0 stable build via CWM
- install Motorola stock rom via fastboot
- wipe data and cache via fastboot
- wipe data and cache via CWM
- factory reset via OS
... all with the same result - it just boots back into the OS with apps still there that I've deleted many times, and apps not there that I've installed many times. One slight point of note is that when I do the factory reset via OS, for some reason it boots into recovery, rather than back into the OS ... not sure if this is significant
Please help? I've searched around and people have mentioned this problem, but the threads always end without an answer
you could try to unlock your xoom again (even if it is not locked!), that should wipe your /data partition. As to why it doesn't through fastboot (assuming you used fastboot erase userdata), no clue... Also, if you're flashing something through fastboot and you don't get an error message and it still didn't work, that sounds like serious trouble...:-\
Thanks for your reply.
I'll try that out (the unlock) and I'll give fastboot another go with that command. I may have used fastboot -w on one occasion, and:
fastboot flash boot boot.img
fastboot flash system system.img
fastboot flash recovery recovery.img
fastboot flash userdata userdata.img
fastboot erase cache
on another.
I was wondering if I can do anything tricky with mounting/unmounting in CWM, but thats an area I have little of my own knowledge. Any thoughts?
I tried both of those suggestions, with no luck. And no error messages either.
Please continue to help .. I appreciate it!
Must say ive got the same problem - getting spurious erros after updating to the final build (3.0) - even after a hard reset and then going through the startup stuff i still end up with my desktop wallpaper from before....although i must confess i havent done the command line stuff yet...
Sorry buddy, but the bad news is that i put mine in for repair, and they were unable to fix it. They said that some aspect of the hardware had been fried and would need an expensive replacement, which would not be worth the cost. One of the risks of custom ROMs .....
Hey guys,
I've been using this website as reference for years but never had an issue I hadn't already seen asked.
I've been looking for weeks for a solution to this and haven't found anything.
I tried to flash cm10.1 over my stock 4.1.2 and corrupted the system.
It was booting directly to AP Fastboot and showing an error about not calling the ROM properly.
I tried reflashing using RSD Light 5.7 but every time it tried to flash the system it said the phone returned failed.
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
ShiningRaven said:
Hey guys,
I've been using this website as reference for years but never had an issue I hadn't already seen asked.
I've been looking for weeks for a solution to this and haven't found anything.
I tried to flash cm10.1 over my stock 4.1.2 and corrupted the system.
It was booting directly to AP Fastboot and showing an error about not calling the ROM properly.
I tried reflashing using RSD Light 5.7 but every time it tried to flash the system it said the phone returned failed.
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
Click to expand...
Click to collapse
Format system via any of the custom recoveries before flashing your new ROM - this will wipe out any leftover problems completely & should let you start 100% fresh with a new ROM.
tzlot said:
Format system via any of the custom recoveries before flashing your new ROM - this will wipe out any leftover problems completely & should let you start 100% fresh with a new ROM.
Click to expand...
Click to collapse
I lost my root when I originally got stuck in fastboot. And I can't boot up the phone until I can get it fixed.
ShiningRaven said:
I lost my root when I originally got stuck in fastboot. And I can't boot up the phone until I can get it fixed.
Click to expand...
Click to collapse
Can you get back into fastboot now? If so
Use fastboot to flash a custom recovery (CWM, TWRP or OUDHS)
use the recovery to factory reset, wipe cache/dalvic, AND format system (sometimes in the advanced menu)
then flash rom of your choice.
If you can't get fastboot working you'll need smarter help than I can give you... but the format system step clears out all kinds of gremlins.
I can get into fast boot but I don't have an unlocked boot loader to flash anything custom.
ShiningRaven said:
I can get into fast boot but I don't have an unlocked boot loader to flash anything custom.[/QUOTE
If you can get into fastboot then you should be able to unlock b/l with this toolkit I used it and it worked for me you can also flash rom with it its in the orginial development thread
http://forum.xda-developers.com/showthread.php?t=2154995
Click to expand...
Click to collapse
ShiningRaven said:
So I upgraded RSD to v6.1 and tried again. This time the phone says it flashed properly but it freezes during the droid boot logo.
I've tried using the utility and it gives me the same results.
I can get into factory recovery and I've performed several hard resets. But the phone still freezes whenever it tries to load the system.
I'm using a Motorola Factory Cable on a high speed USB port.
Any ideas why I'm stuck in a soft brick that I can't flash out of?
Click to expand...
Click to collapse
Had the same problem after a fastboot via the utility. Try powering your phone down completely and leaving it off for about 5-10 min. This can be tricky with the hardware buttons so if you have access to TWRP that will help as it has a power off option. You might also try flashing again via the utility. I believe that's what I had to do, but the power down method is what a friend suggested based of his experience with the same exact problem you documented.
FIXED!!!
OK first I want to thank everybody who responded. I got tied up with work and kind of forgot about this project for a few days.
Repeated uses of the Utility and RSD both left me stuck with the phone freezing every time it tried to load the system into memory.
I had checked out the toolbox before but I didn't think I could do much from a locked bootloader.
After your suggestion jmcdonald I tried it again. It says my device isn't available to be unlocked so I tried downgrading back to ICS.
The toolbox says that it failed but it must have fixed something because the phone booted back up to android 4.1.2 stock!
So far I have bricked a lot of phones and learned a lot about ADB in the process of fixing them but I've never had one I was so certain was bricked permanently. But now it seems to be working fine, I'm scared to try rebooting in now.
Definatly going to unlock the bootloader pronto.
Thanks again jmcdonald!
FINAL EDIT: FIXED!!! Sparsechunk files 1,2and 3 have to match the exact name with the firmware folder sparsechunk files.
I did not notice that my firmware sparsechunk files ended in .0 .1 .2 and not 1 2 3 like the tutorial had listed, so I was fastbooting the wrong sparsechunk command. That was the final fix that finally worked for me.
Original post:
SHORT VERSION:
My god this has been one crazy root journey.
I have done absolutely EVERYTHING I could pull up on google to fix my phone, and what seemed to be the final piece to the puzzle, still has not fixed anything.
My phone is bricked, and i would really appreciate help at this point.
The current problem:
When I turn on my phone, it vibrates, and displays the WARNING BOOT LOADER UNLOCKED screen, and stays there forever.
I can access my boot loader, and recovery, but I dont know what to do at this point.
I tried a quick flash stock recovery kit kat with moto tool AIO, and it didnt help.
Any ideas?
LONG VERSION (backround info may help to understand the current issue)
Now, if you want to know what began all of this, continue reading, otherwise the above is my current issue.
After successfully unlocking and rooting my phone
I downloaded SWITCHME, an app that lets you create multible users on the phone. the instructions say that you can use a sub account to test and mess around with anything because you can simply go back to the admin account that has everything untouched.
That was a lie.
1.I deleted .setup, along with a few other things THAT WHERE NOT FLAGGED AS IMPORTANT, assuming the phone would still work. and my phone went bonkers, displaying this infinite message: UNFORTUNATELY, SETUP HAS STOPPED. It was impossible to use the phone, and I could only access bootloader.
2.After endless googling, driver downloading, xda mod installing, I managed to set up my boot loader to do the guide restore stock firmware:http://forum.xda-developers.com/showthread.php?t=2542219
Sadly, I flashed the wrong model number package, I was flashing x35, when I later discovered that my phone is x45.
Flashing the x35 firmware bricked my phone further, to where it would "fail to boot up" and would only display bootloader over and over after attempting to turn the phone on.
3. Simple, I realized I flashed the wrong thing, so I downloaded the x45 firmware from the firmware teem on this website, flashed all of the commands, and bam, the phone starts up with the boot loader warning, and DOES NOT get stuck in the previous boot loader issue I had.
But now the phone wont get past that warning screen so... now im pissed.
Please, if anyone can help me I would greatly appreciate it, Im so close to getting my phone back...
EDIT 2: Looks like the phone wont stay shut down, I realized that if I dont open up boot loader, it will turn itself on and display the warning message.
EDIT:
The stuffs I have, ready to try anything:
CWM touch mod
Moto Tool AIO
Minimal ADB and Fast boot
RETUS x1045 factory firmware
All directories, folders, cmd commands are set up and working properly between all of the programs.
The phone appears to be responding to all cmd commands properly.
I also have the windows one touch super boot root method. (he superboot-windows.bat )
Im afraid to try anything major after freshly flashing the x45 firmware that seemed to bring me one step closer without the help of someone else.
I restored stock to my phone using this link yesturday http://www.ibtimes.co.uk/how-restore-motorola-moto-g-stock-firmware-1447290
it may work for you
I have almost the same problem as if the fastboot not install anything despite not display errors
great that you got it done.
maybe my few cents about my "bricking" story. (xt1032 moto g)
yesterday i wanted to change the rom from cm11 nightly to another custom rom like ehndroix/carbonrom...
first i thought that will be done in a few mins, after having already flashed a custom rom.
then the story began, getting adb work, but, 2weeks ago everything was setup and went fine. dunno why my laptop lost the "drivers".
thats the link which solved that problem: tinyurl . com / kgffjh4 [sorry cant post links outside of xda yet, spam protection]
so after a few hours of getting that fixed i, i began flashing.
suddently i got stuck in bootscreen (ehndroix logo for example)...
then i wanted to go back with my previous backup made internaly of clockworkmod. though i couldnt restore my backup because there was an error message while restoring /data of my backup
also when restoring to factory/wipe in cwm there was that error message about clouldnt "touch" /data, i dont remember the message exactly.
after thinking i bricked everything, i though lets wipe my internal sdcard, maybe that causes the /data error.
then i restarted the device and went for a shower... after 15min i came back and my device was "started".
now i dont know that exactly helped, maybe wiping all data on my phone, or just letting my device boot for a "long" time...
so, thats my yesterdays brick story.
do a factory reset if the bootloader has that option.. otherwise install or run/boot a custom revovery, then either
try the factory reset option there and reboot or..
wipe everything and install a rom
Ok try this, I'm was a victim too:
Relock and unlock bootloader
Download and flash latest Philz
From there format everything...EVERY PARTITION...switch F2FS
After switching wipe every partition again
Select and execute the other 3 wiping option ie., Clean to install new ROM and the other 2 (I can't remember now)
Do this all over again via TWRP too
Now, this is important, don't use the mfastboot for restoring stock...use the one provided by Google for its Android SDK
Flash the stock images
Flash the Moto Razr boot animation and not the one for Moto G to remove the warning sign
I'm 99.99% sure your phone will boot properly
After the phone boots, reflash the Moto G bootanimation
Good Luck!
ngr.hd said:
Ok try this, I'm was a victim too:
Relock and unlock bootloader
Download and flash latest Philz
From there format everything...EVERY PARTITION...switch F2FS
After switching wipe every partition again
Select and execute the other 3 wiping option ie., Clean to install new ROM and the other 2 (I can't remember now)
Do this all over again via TWRP too
Now, this is important, don't use the mfastboot for restoring stock...use the one provided by Google for its Android SDK
Flash the stock images
Flash the Moto Razr boot animation and not the one for Moto G to remove the warning sign
I'm 99.99% sure your phone will boot properly
After the phone boots, reflash the Moto G bootanimation
Good Luck!
Click to expand...
Click to collapse
I try to flash any recovery but after entering I get an android and says no commands, and installation does not throw errors
angelgzg said:
I try to flash any recovery but after entering I get an android and says no commands, and installation does not throw errors
Click to expand...
Click to collapse
You're still in stock recovery.
Use fastboot flash recovery xyz.zip to flash philz recovery
Use this when you're in bootloader mode.
ngr.hd said:
You're still in stock recovery.
Use fastboot flash recovery xyz.zip to flash philz recovery
Use this when you're in bootloader mode.
Click to expand...
Click to collapse
I flash the recovery but rebooted into recovery, the android keeps popping up (no commands)
FINAL EDIT: FIXED!!! Sparsechunk files 1,2and 3 have to match the exact name with the firmware folder sparsechunk files.
I did not notice that my firmware sparsechunk files ended in .0 .1 .2 and not 1 2 3 like the tutorial had listed, so I was fastbooting the wrong sparsechunk command. That was the final fix that finally worked for me.
Sorry I'm traveling a d couldnt update thread fast enough.
Hi, guys.
I picked this xt1033 and it had the microusb input damaged, so i replaced it, but since then, it got stucked on motorola logo.
I guessed that the system got corrupted and then i uploaded some new system. It went through nicely, but when it rebooted got stucked again. So, i'ved unlocked it bootloader (to start from zero) and re-locked it, putting a new system from the ground and apparently it ended well, but it got stucked again on logo (and later i've founded that it didn't lock). I've begin to put TWRP to install a custom rom on it (to see if i've could pass throgh that) and founded that my files was still there (EVEN AFTER I'VE UNLOCKED THE BOOTLOADER, who would've erased everything from inside), system, images and even whatsapp files. MTP Service give-me a taste of what was inside and everything was there, nothing corrupt.
So i'ved erased it and put a new rom, TWRP said it did it and was asking for reboot, so i did.
And it got stucked again and nothing was erased.
So the thing is, it's internal storage is freezed and i can't do anything with it.
Could you guys help me? Thanks in advance.
i may be wrong here... but i dont remember unlocking bootloader erased my data.... but it was long time ago...
coming back to your problem.. have you tried using repair option in twrp?
also try wiping all partitions and do a recovery reboot to see if it works
access_unlimited said:
i may be wrong here... but i dont remember unlocking bootloader erased my data.... but it was long time ago...
coming back to your problem.. have you tried using repair option in twrp?
also try wiping all partitions and do a recovery reboot to see if it works
Click to expand...
Click to collapse
Already done.
I could only enter TWRP by boot it on bootloader, not flashing ('cuz was impossible to write on memory and was saying that the flash was successful).
TWRP said it wipe it completely without any error, but it's was there.
And by ordering to reboot on Recovery Mode, it went back to original recovery and trying to erase from there do the same thing (said that was complete, but everything is still there).
Same problem here, this is a problem with emmc bricked
Well, not fully bricked, but it's completely non-working just the same.
I've had the K1 for a few years now and have been fine with the standard, stock OTA updates. Recently though I've been seeing constant notifications that I'm short on ram and after uninstalling apps, deleting old files, it would work ok for a few days and then start complaining about low memory again. So I figured that something must be corrupt and now is a good a time as any to root and see about flashing a new rom.
I've owned many android devices over the years and have rooted and patched most of them. so I'm familiar with the tools.
This time however, I think I must have crossed something up somewhere.
What I did was this:
Grabbed the minimal ADB package and fastboot drivers.
Booted into the bootloader and ran the fastboot oem unlock. No problem.
From the nVidia site, I then grabbed and flashed the latest stock image and recovery, just to ensure I was on a clean slate. No problem.
Flashed the latest TWRP for the device. No problem.
Flashed SuperSU. No problem.
Booted into the stock system to make sure everything was still working and it was. But, this is the start of where I maybe hosed things up(?).
While running stock, I converted the SD card to internal memory, just so I wasn't having to mess with it later, not thinking that I'd have to do it again anyway after flashing a new rom.
Rebooted back to TWRP and proceeded to flash the new rom (AOSP Extended (AEX) 5.8).
I flashed it by way of the sideload method rather than from a zip file sitting on the SD card. This all seemed to work just fine.
Next I went ahead and flashed OpenGapps Mini. This resulted in an error 70 and after reading about it, it was a simple matter of going into the advanced settings in TWRP and extending the system partition. Did that and OpenGapps then flashed with no problem.
Finally I wrapped it up by flashing tegra124-tn8-p1761-1270-a04-e-battery.dtb and rebooted.
... Nothing. Now I know that when flashing a new rom, the first boot can take some time, but I let it sit for about 2 hours with no result. It didn't appear to be boot looping, but instead just stuck on the nVidia boot screen. Forced it to boot back to the bootloader and brought up TWRP. I obviously did something wrong, so I prepared to reflash the stock image.
Did the wipe, flashed the files and rebooted. Again, nothing.
This time however, not only can I not boot to the system, I now also can't get back into recovery.
No matter how many times I reboot, or attempt to reflash anything, it hangs on the boot screen when attempting to get back into recovery.
So I'm stuck. I've tried reflashing TWRP, stock recovery and stock system, with the SD card in and out, a number of times, all with no joy.
I can access the bootloader, so I can at least run fastboot commands, but that's all I can do. Without being in recovery, I can't access an ADB shell if I need to repair anything.
If you're still with me after this rambling mess, do I have any hope at all in recovering this thing?
Hi,
I think the problem is in the modified .dtb try flash the original file.
Or : https://forum.xda-developers.com/showpost.php?p=82359331&postcount=39
greetings
kozaqu said:
Hi,
I think the problem is in the modified .dtb try flash the original file.
Or : https://forum.xda-developers.com/showpost.php?p=82359331&postcount=39
greetings
Click to expand...
Click to collapse
That got me in the right direction and I can at least get back into recovery now. Thanks! :good:
Also in the same boat
mkhopper said:
Well, not fully bricked, but it's completely non-working just the same.
I've had the K1 for a few years now and have been fine with the standard, stock OTA updates. Recently though I've been seeing constant notifications that I'm short on ram and after uninstalling apps, deleting old files, it would work ok for a few days and then start complaining about low memory again. So I figured that something must be corrupt and now is a good a time as any to root and see about flashing a new rom.
I've owned many android devices over the years and have rooted and patched most of them. so I'm familiar with the tools.
This time however, I think I must have crossed something up somewhere.
What I did was this:
Grabbed the minimal ADB package and fastboot drivers.
Booted into the bootloader and ran the fastboot oem unlock. No problem.
From the nVidia site, I then grabbed and flashed the latest stock image and recovery, just to ensure I was on a clean slate. No problem.
Flashed the latest TWRP for the device. No problem.
Flashed SuperSU. No problem.
Booted into the stock system to make sure everything was still working and it was. But, this is the start of where I maybe hosed things up(?).
While running stock, I converted the SD card to internal memory, just so I wasn't having to mess with it later, not thinking that I'd have to do it again anyway after flashing a new rom.
Rebooted back to TWRP and proceeded to flash the new rom (AOSP Extended (AEX) 5.8).
I flashed it by way of the sideload method rather than from a zip file sitting on the SD card. This all seemed to work just fine.
Next I went ahead and flashed OpenGapps Mini. This resulted in an error 70 and after reading about it, it was a simple matter of going into the advanced settings in TWRP and extending the system partition. Did that and OpenGapps then flashed with no problem.
Finally I wrapped it up by flashing tegra124-tn8-p1761-1270-a04-e-battery.dtb and rebooted.
... Nothing. Now I know that when flashing a new rom, the first boot can take some time, but I let it sit for about 2 hours with no result. It didn't appear to be boot looping, but instead just stuck on the nVidia boot screen. Forced it to boot back to the bootloader and brought up TWRP. I obviously did something wrong, so I prepared to reflash the stock image.
Did the wipe, flashed the files and rebooted. Again, nothing.
This time however, not only can I not boot to the system, I now also can't get back into recovery.
No matter how many times I reboot, or attempt to reflash anything, it hangs on the boot screen when attempting to get back into recovery.
So I'm stuck. I've tried reflashing TWRP, stock recovery and stock system, with the SD card in and out, a number of times, all with no joy.
I can access the bootloader, so I can at least run fastboot commands, but that's all I can do. Without being in recovery, I can't access an ADB shell if I need to repair anything.
If you're still with me after this rambling mess, do I have any hope at all in recovering this thing?
Click to expand...
Click to collapse
I'm also sort of in the same boat i had a custom rom installed and decided to go back to stock os and now i'm stuck at either the Nvidia Logo or the Fastboot menu there's nothing else it let's me do i'd take any advice at this point. I can use Fastboot commands and I've tried Flashing Twrp.img and also flashing all the stock os which goes through with no problems i reboot the device and it's just stuck at the Nvidia logo
Ps: how did you manage to get back into recovery
Hello.
I think i had the same Problem.
I Flashed a Custom Rom, MiniGapps and the tegra...Battery file and since then i had boot loop an the NVidia Logo.
The Problem was: i flashed the tegra-Battery.ZIP file!!!
I noticed that i have to unzip it and flash teh tegra-..battery.DTP file.
since then it booted up again.
the OpenGappMini was buggy. it worked with the Nano!
Hope this helps for you as well!
OMG you guys. I did the exact same damn thing. Flashed the ZIP instead of the DTP file. 100 million thanks to you. I'm going to give it a shot now.
It worked! I wonder how many other folks didn't realize it wasn't a zip to flash to dtb and bricked their devices.