[Q] help!!!!! - Sprint Galaxy S 5 Q&A, Help & Troubleshooting

so i have a galaxy s5 from sprint and it updated to 4.4.4 i wanted to root it and i couldnt find out how to do it via 4.4.4 so i downloaded the stock of 4.4.2 from http://www.sammobile.com/firmwares/download/28041/G900PVPU1ANCB_G900PSPT1ANCB_SPR.zip/ and i used odin 3.07 to flash it to my phone. it said successful. here is the log. <OSM> G900PVPU1ANCB_G900PSPT1ANCB_G900PVPU1ANCB_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl1.mbn
<ID:0/004> rpm.mbn
<ID:0/004> tz.mbn
<ID:0/004> sdi.mbn
<ID:0/004> NON-HLOS.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> cache.img.ext4
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
then i let it reboot and now it gets stuck at the sprint screen and wont go to my home screen when i go into download mode afterwards it says knox is 0x0
i tired wipeing the cache

Hi,
I will have your thread moved to your device section so the experts who own your device can help. ?

Sounds like you need to do a full wipe. But before flashing a custom recovery that will trip knox, see what sort of reset settings there are by booting up into stock recovery first.
---------- Post added at 02:33 PM ---------- Previous post was at 02:30 PM ----------
And if you are worried about tripping the Knox counters, DONT flash a custom recovery. I'd recommend taking it in to the local Sprint store and let them factory restore it for you. That way they take any responsibility.

Thank you I figured it out I just did a hardware factory reset and it came back with 4.4.2 on there and rooted

raivyn said:
Thank you I figured it out I just did a hardware factory reset and it came back with 4.4.2 on there and rooted
Click to expand...
Click to collapse
Oh good, glad you got it.
Doing the odin restores doesn't normally wipe anything so you end up restoring right over the top of whatever you were running before.

Related

[Q] Samsung Galaxy I9003 upgrade prob:Froyo to Gingerbird by ODIN and Service Center.

Hi,
I have visited to Samsung Service Center to upgrade from Froyo to Gingerbird, But they failed. Even when I upgraded thorugh Kies and with ODIN, The uprading process has been done successfully, but porblem to reboot just after the upgrading.
Now again i have to degrade the version and my mobile now Froyo "I9003DDKB2_ODDKA6_DDKA5".
What Can i do for upgrading...Please help.
Thanks...
to gingerbread just flash
1.Flash full XXKPE(PDA,PHONE,BOOTLOADER,CSC)+pit
2.Flash full XXKPE
and for stable firmware GB
3.Flash DDLF2
Samsung Galaxy I9003 upgrade prob:Froyo to Gingerbird by ODIN and Service Center.
MR.Volkf said:
to gingerbread just flash
1.Flash full XXKPE(PDA,PHONE,BOOTLOADER,CSC)+pit
2.Flash full XXKPE
and for stable firmware GB
3.Flash DDLF2
Click to expand...
Click to collapse
Thanks for your feedback...
I tired to search the following task list but not able to found.:crying:
CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
MODEM_I9003XXKPE_REV_00_CL1041909.tar
APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
GT-I9003-CSC-MULTI-OXAKPE.tar
can anybody provide the downable link....
Thanks ......
singh29 said:
Thanks for your feedback...
I tired to search the following task list but not able to found.:crying:
CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
MODEM_I9003XXKPE_REV_00_CL1041909.tar
APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
GT-I9003-CSC-MULTI-OXAKPE.tar
can anybody provide the downable link....
Thanks ......
Click to expand...
Click to collapse
You can find it all here bro.. http://forum.xda-developers.com/showthread.php?t=1004647
Samsung Galaxy I9003 upgrade prob:Froyo to Gingerbird by ODIN and Service Center.
malungkot said:
You can find it all here bro.. http://forum.xda-developers.com/showthread.php?t=1004647
Click to expand...
Click to collapse
Can I flesh with the "XKPQ (4 files + pit)" files instead of "XXKPE (4 files + pit)" files ?
singh29 said:
Can I flesh with the "XKPQ (4 files + pit)" files instead of "XXKPE (4 files + pit)" files ?
Click to expand...
Click to collapse
Yes, best to skip the bootloader(APBOOT_I9003XXKPQ_CL709629_REV08_user_low_ship.tar)..flash PIT + PDA + PHONE +CSC
Samsung Galaxy I9003 upgrade prob:Froyo to Gingerbird by ODIN and Service Center.
wee2wee said:
Yes, best to skip the bootloader(APBOOT_I9003XXKPQ_CL709629_REV08_user_low_ship.tar)..flash PIT + PDA + PHONE +CSC
Click to expand...
Click to collapse
Thanks for your replay...
Again Unable to Flesh.......
I have tried with the both XXKPE and XXKPQ files for flesh but unable to flesh. The problem is only coming for booting after fleshed. I have also tried with the "GT-I9003_PDA-XXKPE-fixed (2).tar" but again failed. Used Odin is "Odin3_v3.04". I have done "Restore Factory" internal SD card and then tried but unable to flesh.
After that i have to back with the "I9003DDKB2_ODDKA6_DDKA5.rar" Version.
Used the following files.
PI: latona_20110114.pit
PDA: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
PHONE: MODEM_I9003XXKPE_REV_00_CL1041909.tar
BOOTLOADER: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
CSC: GT-I9003-CSC-MULTI-OXAKPE.tar
AND
latona_20110114.pit
APBOOT_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
CODE_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
GT-I9003-CSC-SERKPQ.tar.md5
MODEM_I9003XXKPQ_REV_00_CL1076353.tar.md5
I don't know what the problem is? :crying::crying::crying:
singh29 said:
Thanks for your replay...
Again Unable to Flesh.......
I have tried with the both XXKPE and XXKPQ files for flesh but unable to flesh. The problem is only coming for booting after fleshed. I have also tried with the "GT-I9003_PDA-XXKPE-fixed (2).tar" but again failed. Used Odin is "Odin3_v3.04". I have done "Restore Factory" internal SD card and then tried but unable to flesh.
After that i have to back with the "I9003DDKB2_ODDKA6_DDKA5.rar" Version.
Used the following files.
PI: latona_20110114.pit
PDA: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
PHONE: MODEM_I9003XXKPE_REV_00_CL1041909.tar
BOOTLOADER: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
CSC: GT-I9003-CSC-MULTI-OXAKPE.tar
AND
latona_20110114.pit
APBOOT_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
CODE_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
GT-I9003-CSC-SERKPQ.tar.md5
MODEM_I9003XXKPQ_REV_00_CL1076353.tar.md5
I don't know what the problem is? :crying::crying::crying:
Click to expand...
Click to collapse
Do you mean the phone does not boot up(stuck at Samsung logo)after flashed XXKPE or XXKPQ and you can boot up after flashed back to Froyo "I9003DDKB2_ODDKA6_DDKA5..that's strange
singh29 said:
Thanks for your replay...
Again Unable to Flesh.......
I have tried with the both XXKPE and XXKPQ files for flesh but unable to flesh. The problem is only coming for booting after fleshed. I have also tried with the "GT-I9003_PDA-XXKPE-fixed (2).tar" but again failed. Used Odin is "Odin3_v3.04". I have done "Restore Factory" internal SD card and then tried but unable to flesh.
After that i have to back with the "I9003DDKB2_ODDKA6_DDKA5.rar" Version.
Used the following files.
PI: latona_20110114.pit
PDA: CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar
PHONE: MODEM_I9003XXKPE_REV_00_CL1041909.tar
BOOTLOADER: APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar
CSC: GT-I9003-CSC-MULTI-OXAKPE.tar
AND
latona_20110114.pit
APBOOT_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
CODE_I9003XXKPQ_CL709629_REV08_user_low_ship.tar.md5
GT-I9003-CSC-SERKPQ.tar.md5
MODEM_I9003XXKPQ_REV_00_CL1076353.tar.md5
I don't know what the problem is? :crying::crying::crying:
Click to expand...
Click to collapse
dnt panic...download XXKPE package, inside that package itself u will find Latona.pit file......now put ur mobile in download mode,connect to odin,flash latona.pit...then remove usb cable nd battery ..again put ur phone in download mode,connect to odin, then flash all 4 files in xxkpe,....that's it..wait for 15 min..u phone will boot up.
---------- Post added at 09:33 PM ---------- Previous post was at 09:30 PM ----------
frst flash latona.pit file alone separately...then u will get a black screen..after that again enter download mode and then connect to odin and flash remaining 4 files..
devasenan200 said:
dnt panic...download XXKPE package, inside that package itself u will find Latona.pit file......now put ur mobile in download mode,connect to odin,flash latona.pit...then remove usb cable nd battery ..again put ur phone in download mode,connect to odin, then flash all 4 files in xxkpe,....that's it..wait for 15 min..u phone will boot up.
---------- Post added at 09:33 PM ---------- Previous post was at 09:30 PM ----------
frst flash latona.pit file alone separately...then u will get a black screen..after that again enter download mode and then connect to odin and flash remaining 4 files..
Click to expand...
Click to collapse
Thanks for your feedback...
Again, Fail to upgrade. As per your comment, I have stand for 30 min after fleshed. Please find the below process has been done with XXKPE package:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5 is valid.
<OSM> GT-I9003-CSC-MULTI-OXAKPE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> normalboot.img
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> system.rfs
<ID:0/004> cache.rfs
<ID:0/004> userdata.rfs
<ID:0/004> modem.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> cache.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
When above process has not been done again i have to back with the Froyo Version. Please find the below process has been done with Froyo "I9003DDKB2_ODDKA6_DDKA5.rar" package:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.rfs
<ID:0/004> modem.bin
<ID:0/004> normalboot.img
<ID:0/004> Sbl.bin
<ID:0/004> system.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
<ID:0/003> Added!!
Thanks......
singh29 said:
Thanks for your feedback...
Again, Fail to upgrade. As per your comment, I have stand for 30 min after fleshed. Please find the below process has been done with XXKPE package:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5 is valid.
<OSM> GT-I9003-CSC-MULTI-OXAKPE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> normalboot.img
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> system.rfs
<ID:0/004> cache.rfs
<ID:0/004> userdata.rfs
<ID:0/004> modem.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> cache.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
When above process has not been done again i have to back with the Froyo Version. Please find the below process has been done with Froyo "I9003DDKB2_ODDKA6_DDKA5.rar" package:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.rfs
<ID:0/004> modem.bin
<ID:0/004> normalboot.img
<ID:0/004> Sbl.bin
<ID:0/004> system.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed
after flashing xxkpe, what Is happening?..did you flash latona file separately first?
Click to expand...
Click to collapse
devasenan200 said:
singh29 said:
Thanks for your feedback...
Again, Fail to upgrade. As per your comment, I have stand for 30 min after fleshed. Please find the below process has been done with XXKPE package:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> APBOOT_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> CODE_I9003XXKPE_CL409735_REV08_user_low_ship.tar.md5 is valid.
<OSM> MODEM_I9003XXKPE_REV_00_CL1041909.tar.md5 is valid.
<OSM> GT-I9003-CSC-MULTI-OXAKPE.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> normalboot.img
<ID:0/004> boot.bin
<ID:0/004> Sbl.bin
<ID:0/004> param.lfs
<ID:0/004> system.rfs
<ID:0/004> cache.rfs
<ID:0/004> userdata.rfs
<ID:0/004> modem.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> cache.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Removed!!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
When above process has not been done again i have to back with the Froyo Version. Please find the below process has been done with Froyo "I9003DDKB2_ODDKA6_DDKA5.rar" package:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.rfs
<ID:0/004> modem.bin
<ID:0/004> normalboot.img
<ID:0/004> Sbl.bin
<ID:0/004> system.rfs
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed
after flashing xxkpe, what Is happening?..did you flash latona file separately first?
Click to expand...
Click to collapse
Yes.... I have tested on both condition with use "Restore factory". Previous i did with the package. but result : Negative
Again I have fleshed separately (latona) and other 4 files.
After 30 min when found result as a negative; I have to flesh with Froyo Version "I9003DDKB2_ODDKA6_DDKA5.rar" and It working fine. No problem found for rebooting.
Click to expand...
Click to collapse
singh29 said:
devasenan200 said:
Yes.... I have tested on both condition with use "Restore factory". Previous i did with the package. but result : Negative
Again I have fleshed separately (latona) and other 4 files.
After 30 min when found result as a negative; I have to flesh with Froyo Version "I9003DDKB2_ODDKA6_DDKA5.rar" and It working fine. No problem found for rebooting.
Click to expand...
Click to collapse
I think prob is only rebooting.
Click to expand...
Click to collapse
any update regarding prob for upgrading froyo to gingerbird or upper version...
singh29 said:
singh29 said:
I think prob is only rebooting.
Click to expand...
Click to collapse
any update regarding prob for upgrading froyo to gingerbird or upper version...
Click to expand...
Click to collapse
Successfully Root the galaxy I9003 but unable to upgrade from froyo to upper version.
singh29 said:
singh29 said:
any update regarding prob for upgrading froyo to gingerbird or upper version...
Click to expand...
Click to collapse
I have successfully Rooted the galaxy I9003 but unable to upgrade from froyo to upper version.
I have tried with the both XXKPE and XXKPQ files for flesh but result is negative. The problem is only coming for booting after fleshed.
Pelase help..
Should i visit to service center for upgrading. ??
Click to expand...
Click to collapse
Hi guys, don't use Odin 3.04
It cause problems, use Odin 1.85
Sent from my C2105 using Tapatalk
..
Could u please put the files needed for flashing the jpkp5 rom?(pit,bootloader,etc)
as chongns said use odin 1.85 or 1.85
remember to check re-partition when flashing latona.pit and uncheck it when flashing the rest of the files
when flashing remember to flash two times the same passage some phones dosen't update correctly with only one flash

[Q] aboot.mbn FAIL I337m

Since I'm a noob and can't post in this thread http://forum.xda-developers.com/showthread.php?t=2261573
I was installing the sphere camea app when I went into Recovery and went to wipe delvik I wiped system instead of cache since the order had changed from when doing this on my S2, I didn't notice that the first 2 options had changed. I tried downloading the stock ROM in the above thread from the first mirror site and when I went to install via ODIN, it keeps giving me the fail message, aboot.mbn. Any ideas ? I have since been able to flash the cyanogenmod, but would like to go back to stock.
I am getting the same type of error except for the Galaxy S4.
Code:
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl1.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl2.mbn
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
That is with the .pit also. Any help out there for this issue?

Soft-Brick - S6 G20F

Hey everyone,
I have first tried to update my cellphone both directly via the phone itself and smart switch with no success. I have no idea why these two didn't work and because I am a very stubborn person I have googled the issue and found out that I can flash a firmware via Odin. Which I tried as well.
My old firmware was G920FXXU1AOD4, I tried to flash the version G920FXXU2BOGG.
Sadly, the result was this :
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1005)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> cm.bin
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am now unable to reboot my phone properly. I have tried to use Smart Switch to use the emergency recovery but it seems like it doesn't recognize my phone so it's not working.
I have also tried to flash a recovery system called twrp but it didn't work either and wouldn't let me enter the recovery system.
I have no idea what to do anymore. My phone is a week old and I feel really stupid for ruining it because I was stubborn and wanted it updated. I am a rookie with flashing, rooting, etc.. I have never done this before.
Any idea of what I can do ? Thanks a lot for any future help, you have my phone's life in your hands and I couldnt be thankful enough if I manage to save it thanks to you all.
Bring your S6 back to Samsung for warranty repair.

[Completed] Soft-bricked SM-P900 stucks on system.img in Odin

Hello. Sorry for my enlgish.
Theres a soft-bricked SM-P900, I can normally open download mode. (But on normal system loading it asking for Kies)
(Samsung Galaxy Note Pro 12.2 WiFi SM-P900)
No ROM installed now. I just can't install it.
Here's the Odin log:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
It's always stucks on "system.img" in ANY .tar I try to flash.
Yesterday, it could power on. But now it's not powering on at all. I hope this is because of battery charge.
===UPD: Yes, it was because of battery charge. Now it's powered on
===UPD2: Now it's powered off again and I can't power it on, what the hell?...
What should I do, guys? Help, please!
Thread closed / Duplicate

Flashing fail SM-G955W

Hey,
I keep having issues with my S8+ that has never been rooted. I flashed it trying to fix an issue with my WiFi forgetting saved networks. If I turned off WiFi or rebooted my phone it forget all saved networks.
I used Samfirm and Odin 3.12.7 to flash it to the latest firmware AQJ4 and then did an OTA update that popped up. I'm still having the issue but keep getting a notification about "Unauthorized modifications, reboot".
Now, I can't even flash the phone anymore... I keep getting a Fail! (Auth) error when trying to flash BL, AP, or CSC... CP seems to work fine.
I've tried everythign I can find online but nothing helps... When in download mode I see:
FRP Lock is off
Warranty Voidis 0x0
System Status is Official
The one thing I've noticed is that my device shows Baseband version AQJ4 but my Build number is AQK3... Is that normal?
Any ideas?
Code:
<ID:0/004> Added!!
<ID:0/004> Odin engine v(ID:3.1207)..
<ID:0/004> File analysis..
<ID:0/004> skip file list for home binary
<ID:0/004> apdp.mbn
<ID:0/004> msadp.mbn
<ID:0/004> persist.img.ext4
<ID:0/004> userdata.img.ext4
<ID:0/004> Home Binary Download
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> NAND Write Start!!
<ID:0/004> SingleDownload.
<ID:0/004> abl.elf
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Categories

Resources